Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diffusion model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Hydrogen Sensor for Parabolic Trough Expansion Tanks

The National Renewable Energy Laboratory and Acciona Energy North America are developing and implementing a process that addresses the issue of hydrogen buildup in parabolic trough power plants. We are pursuing a method that selectively removes hydrogen from the expansion tanks of the power plant to control hydrogen levels in the circulating heat-transfer fluid. As part of this effort, we are developing a sensor that measures hydrogen partial pressure in the expansion-tank headspace gas. During previous work, we demonstrated that our sensor design measures hydrogen levels over a wide partial pressure range from 1.33 mbar down to 0.003 mbar with an accuracy of +/-20%. We acquired these results under limited conditions because we measured hydrogen partial pressure in gas mixtures of hydrogen and nitrogen only. In this paper, we report our most recent results in which we measured hydrogen partial pressures in gas mixtures that contain hydrogen, nitrogen, biphenyl, and diphenylether. Our results for this gas mixture were essentially the same as those obtained for the hydrogen/nitrogen mixture only, and they also had the same accuracy of +/-20%. This level of accuracy is sufficient to evaluate the performance of a hydrogen mitigation process because hydrogen partial pressure in the expansion tank decreases more than an order of magnitude when the mitigation process is operating. We examined the palladium/silver membrane after completing these measurements and did not observe any signs of membrane deterioration or contamination due to exposure to biphenyl and diphenylether at 405 degrees C. The membrane for these tests was 25 um thick. For the next sensor design that we are developing in 2018, we are using a membrane that is 127 um thick. This thickness is required for the membrane to withstand the 150 psi pressure drop across the membrane when exposed to actual headspace gas from the expansion tank. We performed initial tests in which we exposed a 127-um-thick palladium alloy membrane to 400 degrees C and 150 psi pressure drop and observed no signs of failure or gas leakage. Finally, we developed a transient model that accounts for hydrogen transport mechanisms within the sensor when measurements are made. Our model accounted for hydrogen diffusion through the boundary layer that is adjacent to the membrane and for hydrogen permeation across the membrane and into the permeate volume. Our modeling results agreed very closely with our experimental data when we assumed a boundary-layer thickness of 0.2 cm. This thickness is within the range of expected thicknesses for this gas composition, temperature, and pressure at minimum flowrate. Our model results showed that hydrogen diffusion through the boundary layer adjacent to the membrane is the rate-determining step for the transient pressure response when measuring hydrogen partial pressure.

14 SOLAR ENERGY↗

NMR spin-rotation relaxation and diffusion of methane

The translational diffusion-coefficient and the spin-rotation contribution to the 1 H NMR relaxation rate for methane (CH 4 ) are investigated using MD (molecular dynamics) simulations, over a wide range of densities and temperatures, spanning the liquid, supercritical, and gas phases. Here, the simulated diffusion-coefficients agree well with measurements, without any adjustable parameters in the interpretation of the simulations. A minimization technique is developed to compute the angular velocity for non-rigid spherical molecules, which is used to simulate the autocorrelation function for spin-rotation interactions. With increasing diffusivity, the autocorrelation function shows increasing deviations from the single-exponential decay predicted by the Langevin theory for rigid spheres, and the deviations are quantified using inverse Laplace transforms. The 1 H spin-rotation relaxation rate derived from the autocorrelation function using the “kinetic model” agrees well with measurements in the supercritical/gas phase, while the relaxation rate derived using the “diffusion model” agrees well with measurements in the liquid phase. 1 H spin-rotation relaxation is shown to dominate over the MD-simulated 1 H- 1 H dipole-dipole relaxation at high diffusivity, while the opposite is found at low diffusivity. At high diffusivity, the simulated spin-rotation correlation time agrees with the kinetic collision time for gases, which is used to derive a new expression for 1 H spin-rotation relaxation, without any adjustable parameters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

GALACTIC WINDS DRIVEN BY ISOTROPIC AND ANISOTROPIC COSMIC-RAY DIFFUSION IN DISK GALAXIES

The physics of cosmic rays (CRs) is a promising candidate for explaining the driving of galactic winds and outflows. Recent galaxy formation simulations have demonstrated the need for active CR transport either in the form of diffusion or streaming to successfully launch winds in galaxies. However, due to computational limitations, most previous simulations have modeled CR transport isotropically. Here, we discuss high-resolution simulations of isolated disk galaxies in a 10{sup 11} M {sub ⊙} halo with the moving-mesh code Arepo that include injection of CRs from supernovae, advective transport, CR cooling, and CR transport through isotropic or anisotropic diffusion. We show that either mode of diffusion leads to the formation of strong bipolar outflows. However, they develop significantly later in the simulation with anisotropic diffusion compared to the simulation with isotropic diffusion. Moreover, we find that isotropic diffusion allows most of the CRs to quickly diffuse out of the disk, while in the simulation with anisotropic diffusion, most CRs remain in the disk once the magnetic field becomes dominated by its azimuthal component, which occurs after ∼300 Myr. This has important consequences for the gas dynamics in the disk. In particular, we show that isotropic diffusion strongly suppresses the amplification of the magnetic field in the disk compared to anisotropic or no diffusion models. We therefore conclude that reliable simulations which include CR transport inevitably need to account for anisotropic diffusion.

79 ASTRONOMY AND ASTROPHYSICS↗

Metal Removal by a Free Surface Constructed Wetland and Prediction of Metal Bioavailability and Toxicity with Diffusive Gradients in Thin Films (DGT) and Biotic Ligand Model (BLM)

The H-02 constructed wetland is a free water surface wetland to remove copper (Cu) and zinc (Zn) from the industrial wastewater. In this study, we evaluated the performance of the wetland from 2018 to 2019 and coupled the diffusive gradients in thin films (DGTs) and biotic ligand model (BLM) to explore metal speciation and bioavailability in wetland waters. Surface water samples were collected and piston DGTs were deployed in different sites of the wetland. The H-02 wetland functioned well during the sampling period with high removal efficiencies (Cu: 73.8 ± 1.2% and Zn: 75.2 ± 16.0%). In our study, with the assumption that the combination of BLM predicted inorganic metals species, BLM Cu(II) and BLM Zn(II), were the bioavailable and toxic species, DGT-Cu did not correlate to BLM Cu(II) (P = 0.47), but DGT-Zn positively correlated to BLM Zn(II) (R 2 = 0.35, P < 0.001). Compared to the modeling results of BLM, DGT-indicated labile and/or bioavailable Cu included not only free Cu ions and inorganic Cu complexes but also a high percentage of Cu-labile organic matter complexes. DGT-indicated Zn included free Zn ion, inorganic Zn, and only a low percentage of Zn-labile organic matter complexes. Our findings illustrated the appropriate use of passive sampling techniques and geological modeling when biomonitoring could be substituted. Furthermore, the close monitoring of metal concentrations, speciation, and bioavailability helps us understand metal biogeochemistry and metal removal processes and ensure the long-term sustainability of the constructed wetland.

54 ENVIRONMENTAL SCIENCES↗

Correlation between self-diffusion in Si and the migration mechanisms of vacancies and self-interstitials: An atomistic study

The migration of point defects in silicon and the corresponding atomic mobility are investigated by classical molecular dynamics simulations using the Stillinger-Weber potential and the Tersoff potential. In contrast to most of the previous studies both the point defect diffusivity and the self-diffusion coefficient per defect are calculated separately so that the diffusion-correlation factor can be determined. Simulations with both the Stillinger-Weber and the Tersoff potential show that vacancy migration is characterized by the transformation of the tetrahedral vacancy to the split vacancy and vice versa and the diffusion-correlation factor is about 0.5. This value was also derived by the statistical diffusion theory under the assumption of the same migration mechanism. The mechanisms of self-interstitial migration are more complex. The detailed study, including a visual analysis and investigations with the nudged elastic band method, reveals a variety of transformations between different self-interstitial configurations. Molecular dynamics simulations using the Stillinger-Weber potential show, that the self-interstitial migration is dominated by a dumbbell mechanism, whereas the interstitialcy mechanism prevails with the Tersoff potental. The corresponding values of the correlation factor are different, namely 0.59 and 0.69 for the dumbbell and the interstitialcy mechanism, respectively. The latter value is nearly equal to that obtained by the statistical theory which assumes the interstitialcy mechanism. Recent analysis of experimental results demonstrated, that in the framework of state-of-the-art diffusion and reaction models the best interpretation of point defect data can be given by assuming . The comparison with the present atomistic study leads to the conclusion that a dumbbell mechanism governs the self-interstitial migration in Si. Simulations using the Stillinger-Weber potential reveal two dominating migration paths which are characterized by transformation between the extended <110> dumbbell and the <110> dumbbell and vice versa. This process occurs either in a single {110} plane or includes a change into an equivalent {110} plane.

36 MATERIALS SCIENCE↗

Electric dipolar interaction assisted growth of single crystalline organic thin films

We report on a forest-like-to-desert-like pattern evolution in the growth of an organic thin film observed by using an atomic force microscope. We use a modified diffusion limited aggregation model to simulate the growth process and are able to reproduce the experimental patterns. The energy of electric dipole interaction is calculated and determined to be the driving force for the pattern formation and evolution. Based on these results, single crystalline films are obtained by enhancing the electric dipole interaction while limiting effects of other growth parameters.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Model Parameter Development for Complex Materials: Species-Specific Diffusion Barriers in 316 Stainless Steel from Systematic DFT Calculations

Vacancy-mediated diffusion barriers in 316 stainless steel have been systematically calculated using density functional theory to provide essential parameters for mesoscale microstructure evolution models. A statistical sampling approach employing 210 nudged elastic band calculations across multiple special quasi-random structures captures the effects of local chemical environments in this concentrated alloy. The computational methodology addresses challenges specific to chemically disordered systems, including proper magnetic treatment throughout multi-step calculations and validation against experimental structural properties. The calculated activation barriers reveal clear species-dependent diffusion behavior with the hierarchy Ni >> Fe ˜ Cr >> Mo. Nickel exhibits the highest barriers (0.74–1.31 eV, mean 1.045 eV), confirming its role as the slowest-diffusing major component. Iron and chromium show similar moderate barriers averaging 0.587 eV and 0.522 eV, respectively. Remarkably, molybdenum demonstrates exceptionally low barriers (0.12–0.28 eV, mean 0.194 eV), suggesting much higher mobility than previously recognized and potentially significant implications for precipitation kinetics and microstructure evolution. The barrier ranges remain consistent across different 316 SS compositions, supporting parameter transferability for modeling applications. The overall mean barrier of 0.64 eV provides a practical approximation for phase field simulations, while species-specific values enable detailed treatments of diffusion-controlled processes. This systematic approach establishes a validated framework for generating diffusion parameters in other concentrated alloys where experimental data are limited, while providing the first systematic set of species-specific barriers for predictive modeling of 316 stainless steel microstructure evolution.

36 MATERIALS SCIENCE↗

Channel length dependence of negative-bias-illumination-stress in amorphous-indium-gallium-zinc-oxide thin-film transistors

We have investigated the dependence of Negative-Bias-illumination-Stress (NBIS) upon channel length, in amorphous-indium-gallium-zinc-oxide (a-IGZO) thin-film transistors (TFTs). The negative shift of the transfer characteristic associated with NBIS decreases for increasing channel length and is practically suppressed in devices with L = 100-μm. The effect is consistent with creation of donor defects, mainly in the channel regions adjacent to source and drain contacts. Excellent agreement with experiment has been obtained by an analytical treatment, approximating the distribution of donors in the active layer by a double exponential with characteristic length L{sub D} ∼ L{sub n} ∼ 10-μm, the latter being the electron diffusion length. The model also shows that a device with a non-uniform doping distribution along the active layer is in all equivalent, at low drain voltages, to a device with the same doping averaged over the active layer length. These results highlight a new aspect of the NBIS mechanism, that is, the dependence of the effect upon the relative magnitude of photogenerated holes and electrons, which is controlled by the device potential/band profile. They may also provide the basis for device design solutions to minimize NBIS.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Physical effects on compact high-velocity clouds in the circumgalactic medium

ABSTRACT We numerically investigate the evolution of compact high-velocity clouds (CHVCs) passing through a hot, tenuous gas representing the highly ionized circumgalactic medium (CGM) by applying the adaptive-mesh refinement code flash. The model clouds start from both hydrostatic and thermal equilibrium and are in pressure balance with the CGM. Here, we present 14 models, divided into two mass categories and two metallicities each and different velocities. We allow for self-gravity and thermal conduction or not. All models experience mass diffusion, radiative cooling, and external heating leading to dissociation and ionization. Our main findings are (1) self-gravity stabilizes clouds against Rayleigh–Taylor instability, which is disrupted within 10 sound-crossing times without; (2) clouds can develop Jeans-instable regions internally even though they are initially below Jeans mass; (3) all clouds lose mass by ram pressure and Kelvin–Helmholtz instability; (4) thermal conduction substantially lowers mass-loss rates, by this, extending the clouds’ lifetimes, particularly, more than doubling the lifetime of low-mass clouds; (5) thermal conduction leads to continuous, filamentary stripping, while the removed gas is heated up quickly and mixes efficiently with the ambient CGM; (6) without thermal conduction the removed gas consists of dense, cool, clumpy fragments; (7) thermal conduction might prevent CHVCs from forming stars; and (8) clouds decelerated by means of drag from the ambient CGM form head-tail shapes and collapse after they reach velocities characteristic for intermediate-velocity clouds. Conclusively, only sophisticated modelling of CHVCs as non-homogeneous and non-isothermal clouds with thermal conduction and self-gravity explains observed morphologies and naturally leads to the suppression of star formation.

Sander, Bastian↗

Modeling Tritium Transport, Deposition and Re-emission

The atmospheric release of tritium oxide (HTO) potentially impacts human health, typically through inhalation or absorption. Due to HTO's similarity to water, vegetation will absorb HTO by solution in the leaf water and then re-emit it, creating a number of secondary sources of HTO. Currently, models used for emergency response at Savannah River Site incorporate the transport and deposition of HTO but do not provide estimates for its potential re-emission from vegetation or soil surface though re-emission could result in prolonged exposure and greater than predicted dose for an individual downwind. A simple model of HTO transport, deposition and re-emission has been developed to examine the potential increase in exposure and dose. The model simulates an initial release of HTO that moves with a mean wind and expands through diffusion as a Gaussian puff. Deposition is modeled using previous estimates of deposition velocity for HTO and re-emission is modeled using a time constant that describes how quickly HTO is transferred between the surface and atmosphere. Additional puffs are created to simulate re-emission of HTO as well as horizontal diffusion across model grid cells. An evaluation of field data indicates that the use of a re-emission module tends to improve model predictions through improved prediction of peak concentration magnitude and location. When considering dose, nearly all of the released material is included in the dose calculation when re-emission is included. Although exposure to HTO through re-emission occurs over a few hours, the incremental increase in dose is relatively small because the atmospheric concentration of re-emitted HTO is much lower than the initial release.

54 ENVIRONMENTAL SCIENCES↗

Kinetic analysis of the interactions between calcium ferrite and coal char for chemical looping gasification applications: Identifying reduction routes and modes of oxygen transfer

Chemical Looping Gasification (CLG) is an emerging technology that shows promise for efficient coal gasification by eliminating the need for energy intensive gas separations to achieve a non-nitrogen diluted syngas stream. Oxygen from oxygen carriers, such as CaFe 2 O 4 , are used for coal gasification in place of conventionally produced gaseous oxygen from cryogenic separation of air. These oxygen carriers are unique for their ability to selectively oxidize coal to form syngas and show limited reactivity with syngas components (H 2 , CO). To gain a deeper understanding of how these unique oxygen carriers perform and to offer a first attempt at the reaction modeling of solid mediated interactions of this nature, this study was carried out to determine the kinetic parameters associated with the selective oxidation of coal derived char (Wyodak and Illinois #6) with a metal ferrite, CaFe 2 O 4 . Using thermogravimetric analysis (TGA) coupled with mass spectrometry, the selective oxygen release of metal ferrite in the presence of char by proximal contact was examined. The application of combinatory model fitting approaches was used to describe controlling resistances during oxygen release. A combination of the modified shrinking core model (SCM) with planar oxygen ion diffusion control and reaction order based models was used for kinetic parameter determination. CaFe 2 O 4 particle size plays a major role in the prevailing mode of oxygen release. Particle sizes on the order of 40–50 μm tend to favor first order kinetically controlled regimes independent of geometric and diffusion controls. The probability for oxygen ion diffusion controlling regimes increased when the particle size range of the oxygen carrier was increased up to 350 μm. Char type also impacted the prevalence of the controlling regime. Higher ranked chars react in a slower manner, limiting the gradient for oxygen ion release from the oxygen carrier. Activation energies determined for this process range from 120–200kJ/mol and oxygen ion diffusion coefficients are on the order of 10-8 cm 2 /s. It is suggested that oxygen ion movement is regulated by lattice diffusion out of partially reduced phases (Ca 2 Fe 2 O 5 ) and through reduced outer layers composed of CaO and Fe. The controlled movement of oxygen ions influences the rate of carbon oxidation in the char and therefore the selectivity towards partial oxidation products, which are desirable in CLG applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

THE INFLUENCE OF DEUTERATION AND TURBULENT DIFFUSION ON THE OBSERVED D/H RATIO

The influence of turbulent mixing on the chemistry of the interstellar medium (ISM) has so far received little attention. Previous studies of this effect have suggested that it might play an important role in mixing the various phases of the ISM. In this paper, we examine the potential effects of turbulent diffusion on the deuterium chemistry within molecular clouds. We find that such mixing acts to reduce the efficiency of deuteration in these clouds by increasing the ionization fraction and reducing freeze-out of heavy molecules. This leads to lower abundances for many deuterated species. We also examine the influence of turbulent mixing on the transition from atomic hydrogen to H{sub 2} and from atomic deuterium to HD near the cloud edge. We find that including turbulent diffusion in our models serves to push these transitions deeper into the cloud and helps maintain a higher atomic fraction throughout the cloud envelope. Based on these findings, we propose a new process to account for the significant scatter in the observed atomic D/H ratio for galactic sightlines extending beyond the Local Bubble. Although several mechanisms have been put forward to explain this scatter, they are unable to fully account for the range in D/H values. We suggest a scenario in which turbulent mixing of atomic and molecular gas at the edges of molecular clouds causes the observed atomic D/H ratio to vary by a factor of {approx}2.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effects of various parameters of different porous transport layers in proton exchange membrane water electrolysis

Porous transport layers (PTLs) play an important role in proton exchange membrane water electrolysis (PEMWE) cells. The PTL facilitates water and gas transport, as well as thermal and electrical conduction, and is required to sustain good contact with adjacent components. It is expected that using PTLs with variations in material properties such as structure, composition, thickness and wettability results in performance changes of the PEMWE. Here, a general mathematical PEMWE model is developed that separates and analyzes the contributions of ohmic, activation, diffusion and Nernst potentials. For model validation, three inherently different anode PTL structures (carbon paper, sintered titanium particles, and titanium felt) are operated over a range of conditions. Additionally, the effects of PTL wettability were used to verify the model using Polytetrafluoroethylene (PTFE) treated Toray papers with PTFE loading ranging from 0% to 20%. The modeling results of both PTFE treated and untreated materials show good agreement with the experimental data. Mass transport or diffusion loss is the primary reason for performance differences between PTFE treated and untreated PTLs. Sintered titanium PTLs with thicknesses above 1 mm suffer from up to 33% increased ohmic losses without indicating any obvious changes in activation and diffusion losses when compared to untreated PTLs. The losses of the cell increase when using PTFE treated Toray paper. Individual contributions are quantified and assigned to increased ohmic, activation, and diffusion losses. In conclusion, the proposed model offers insights into the overpotential contributions of a PEMWE. It is a useful tool for predicting performance of various PTL materials and can be applied for PTL development and optimization efforts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Estimation of unsaturated zone traveltimes for Rainier Mesa and Shoshone Mountain, Nevada Test Site, Nevada, using a source-responsive preferential-flow model

Traveltimes for contaminant transport by water from a point in the unsaturated zone to the saturated zone are a concern at Rainier Mesa and Shoshone Mountain in the Nevada Test Site, Nevada. Where nuclear tests were conducted in the unsaturated zone, contaminants must traverse hundreds of meters of variably saturated rock before they enter the saturated zone in the carbonate rock, where the regional groundwater system has the potential to carry them substantial distances to a location of concern. The unsaturated-zone portion of the contaminant transport path may cause a significant delay, in addition to the time required to travel within the saturated zone, and thus may be important in the overall evaluation of the potential hazard from contamination. Downward contaminant transport through the unsaturated zone occurs through various processes and pathways; this can lead to a broad distribution of contaminant traveltimes, including exceedingly slow and unexpectedly fast extremes. Though the bulk of mobile contaminant arrives between the time-scale end members, the fastest contaminant transport speed, in other words the speed determined by the combination of possible processes and pathways that would bring a measureable quantity of contaminant to the aquifer in the shortest time, carries particular regulatory significance because of its relevance in formulating the most conservative hazard-prevention scenarios. Unsaturated-zone flow is usually modeled as a diffusive process responding to gravity and pressure gradients as mediated by the unsaturated hydraulic properties of the materials traversed. The mathematical formulation of the diffuse-flow concept is known as Richards' equation, which when coupled to a solute transport equation, such as the advection-dispersion equation, provides a framework to simulate contaminant migration in the unsaturated zone. In recent decades awareness has increased that much fluid flow and contaminant transport within the unsaturated zone takes place as preferential flow, faster than would be predicted by the coupled Richards' and advection-dispersion equations with hydraulic properties estimated by traditional means. At present the hydrologic community has not achieved consensus as to whether a modification of Richards' equation, or a fundamentally different formulation, would best quantify preferential flow. Where the fastest contaminant transport speed is what needs to be estimated, there is the possibility of simplification of the evaluation process. One way of doing so is by a two-step process in which the first step is to evaluate whether significant preferential flow and solute transport is possible for the media and conditions of concern. The second step is to carry out (a) a basic Richards' and advection-dispersion equation analysis if it is concluded that preferential flow is not possible or (b) an analysis that considers only the fastest possible preferential-flow processes, if preferential flow is possible. For the preferential-flow situation, a recently published model describable as a Source-Responsive Preferential-Flow (SRPF) model is an easily applied option. This report documents the application of this two-step process to flow through the thick unsaturated zones of Rainier Mesa and Shoshone Mountain in the Nevada Test Site. Application of the SRPF model involves distinguishing between continuous and intermittent water supply to preferential flow paths. At Rainier Mesa and Shoshone Mountain this issue is complicated by the fact that contaminant travel begins at a location deep in the subsurface, where there may be perched water that may or may not act like a continuous supply, depending on such features as the connectedness of fractures and the nature of impeding layers. We have treated this situation by hypothesizing both continuous and intermittent scenarios for contaminant transport to the carbonate aquifer and reporting estimation of the fastest speed for both of these end members.

58 GEOSCIENCES↗

Helium segregation on surfaces of plasma-exposed tungsten

Here we report a hierarchical multi-scale modeling study of implanted helium segregation on surfaces of tungsten, considered as a plasma facing component in nuclear fusion reactors. We employ a hierarchy of atomic-scale simulations based on a reliable interatomic interaction potential, including molecular-statics simulations to understand the origin of helium surface segregation, targeted molecular-dynamics (MD) simulations of near-surface cluster reactions, and large-scale MD simulations of implanted helium evolution in plasma-exposed tungsten. We find that small, mobile He-n (1 <= n <= 7) clusters in the near-surface region are attracted to the surface due to an elastic interaction force that provides the thermodynamic driving force for surface segregation. Elastic interaction force induces drift fluxes of these mobile Hen clusters, which increase substantially as the migrating clusters approach the surface, facilitating helium segregation on the surface. Moreover, the clusters' drift toward the surface enables cluster reactions, most importantly trap mutation, in the near-surface region at rates much higher than in the bulk material. Moreover, these near-surface cluster dynamics have significant effects on the surface morphology, near-surface defect structures, and the amount of helium retained in the material upon plasma exposure. We integrate the findings of such atomic-scale simulations into a properly parameterized and validated spatially dependent, continuum-scale reaction-diffusion cluster dynamics model, capable of predicting implanted helium evolution, surface segregation, and its near-surface effects in tungsten. This cluster-dynamics model sets the stage for development of fully atomistically informed coarse-grained models for computationally efficient simulation predictions of helium surface segregation, as well as helium retention and surface morphological evolution, toward optimal design of plasma facing components.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Focused Ion Beam Tomography of Alloy 617 Corroded in Molten Chloride Salt

Materials qualification of reactor structural materials is a critical step in rapid implementation of advanced nuclear reactor technologies, particularly to assess the corrosion performance in these designs. Accelerated qualification of reactor structural materials requires incorporating powerful computational toolsets, such as phase field modelling in the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework, to predict the evolution of structural materials due to corrosion. Accordingly, computational toolsets will require experimental data generated at appropriate length scales to validate accuracy. Focused ion beam (FIB) provides a high degree of control over manipulation of materials for analytical purposes, including capturing data on the evolution in the microstructure and elemental composition of materials at the mesoscale, an appropriate length scale for phase field modelling of intergranular diffusion phenomena using the MOOSE framework. For instance, the FEI Helios G4 UX dual beam plasma FIB microscope at the Irradiated Materials Characterization Laboratory (IMCL) is capable of backscatter diffraction (EBSD) and energy-dispersive x-ray spectroscopy (EDS) documenting the evolution in the microstructure and elemental composition, respectively. The Helios can perform EDS and EBSD three-dimensionally (3D) using tomography, which is then combined using different software packages to visualize 3D volumes correlating elemental composition to microstructural data. The purpose of this investigation was to develop a streamlined characterization and data processing workflow for 3D tomography studies on the FEI Helios G4 plasma FIB. The investigation is segmented into three parts: 1) Optimizing the data collection workflow, 2) identifying appropriate data processing and visualization software (i.e. DREAM.3D, MIPAR, and VGStudioMax), and 3) establishing an infrastructure for public release. The optimization of the data collection workflow is in collaboration with members of the U220 department to setup formal training on the tomography operation of the G4, through ThermoFisher Scientific, and exploring DREAM.3D, MIPAR, and VGStudioMax data processing/visualization software packages. VGStudioMax currently demonstrates the most promise for future use. Optimization of the data collection and processing workflow is still ongoing. A collaboration with INL High Performance Computing (HPC) established an open-source license for expediting the public release of FIB tomography datasets through HPC. FIB tomography data generated by the G4 will provide comprehensive data for validating 3D phase field mesoscale modelling tools within the MOOSE framework for accelerated qualification of reactor structural materials.

Copeland-Johnson, Trishelle↗

Metastable phase formation and magnetic properties of the Fe-Nb system studied by atomistic modeling and ion beam mixing

With the aid of ab initio calculations, an n-body Fe-Nb embedded-atom potential is first constructed and then applied to study the crystal-to-amorphous phase transition through molecular dynamic simulations. The simulations determine that the glass-forming range of the Fe-Nb system is 18-83 at. % of Nb. In ion beam mixing experiments, five Fe-Nb multilayered films with overall compositions of Fe{sub 85}Nb{sub 15}, Fe{sub 75}Nb{sub 25}, Fe{sub 55}Nb{sub 45}, Fe{sub 25}Nb{sub 75}, and Fe{sub 15}Nb{sub 85}, respectively, are irradiated by 200 keV xenon ions to doses in the range of (1-7)x10{sup 15}Xe{sup +}/cm{sup 2}. The result shows that the Fe-Nb metallic glasses can be synthesized within a composition range of 25-75 at. % of Nb, matching reasonably well the theoretical prediction. Moreover, in the Fe{sub 55}Nb{sub 45} sample, a fcc-structured alloy phase with a large lattice constant of a{approx_equal}0.408 nm was obtained at a dose of 3x10{sup 15} Xe{sup +}/cm{sup 2} and the associated magnetic moment per Fe atom was measured to be 2.41{mu}{sub B}. The observed magnetic moment is much greater than the initial value of 1.42{mu}{sub B} in the bcc-Fe lattice and can thus serve as evidence confirming the high-spin ferromagnetic state of fcc Fe predicted by ab initio calculations. Interestingly, further irradiation induced phase separation in the Fe{sub 55}Nb{sub 45} sample, i.e., irradiation to a dose of 5x10{sup 15} Xe{sup +}/cm{sup 2} results in the growth of a fractal pattern consisting of Fe{sub 72}Nb{sub 28} nanoclusters embedded in Fe{sub 35}Nb{sub 65} matrix. The formation mechanism of the metastable phases as well as that of the fractal pattern observed in the Fe-Nb system was discussed in terms of the atomic collision theory and the well-known cluster-diffusion-limited-aggregation model.

36 MATERIALS SCIENCE↗