Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cross Section”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Electroproduction of the Λ/Σ 0 hyperons at Q 2 ≃ 0.5 (GeV/c) 2 at forward angles

In 2018, the E12-17-003 experiment was conducted at the Thomas Jefferson National Accelerator Facility (JLab) to explore the possible existence of an nn⁢Λ state in the reconstructed missing mass distribution from a tritium gas target [K. N. Suzuki et al., Prog. Theor. Exp. Phys. 2022, 013D01 (2022); B. Pandey et al., Phys. Rev. C 105, L051001 (2022)]. As part of this investigation, data were also collected using a gaseous hydrogen target, not only for a precise absolute mass scale calibration but also for the study of Λ/Σ 0 electroproduction. This dataset was acquired at Q 2 ≃ 0.5 (GeV/c) 2 , W = 2.14 GeV, and θ$^{c.m.}_{γK}$ ≃ 8°. It covers forward angles where photoproduction data are scarce and a low-Q 2 region that is of interest for hypernuclear experiments. On the other hand, this kinematic region is at a slightly higher Q 2 than previous hypernuclear experiments, thus providing crucial information for understanding the Q 2 dependence of the differential cross sections for Λ/Σ 0 hyperon electroproduction. Here, this paper reports on the Q 2 dependence of the differential cross section for the e + p → e' + K + + Λ/Σ 0 reaction at 0.2–0.8 (GeV/c) 2 , and provides comparisons with the currently available theoretical models.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Measurements of the associated production of a W boson and a charm quark in proton–proton collisions at $\sqrt{s}$ = $\mathrm{8 TeV}$

Measurements of the associated production of a W boson and a charm (c) quark in proton–proton collisions at a centre-of-mass energy of 8TeV are reported. The analysis uses a data sample corresponding to a total integrated luminosity of 19.7 fb -1 collected by the CMS detector at the LHC. The W bosons are identified through their leptonic decays to an electron or a muon, and a neutrino. Charm quark jets are selected using distinctive signatures of charm hadron decays. The product of the cross section and branching fraction σ(pp → W + c + X)β(W →ℓv), where ℓ = e or μ, and the cross section ratio σ(pp → W + + $\bar{c}$ + X)/σ(pp → W - + c + X) are measured in a fiducial volume and differentially as functions of the pseudorapidity and of the transverse momentum of the lepton from the W boson decay. The results are compared with theoretical predictions. The impact of these measurements on the determination of the strange quark distribution is assessed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Transport @ LANL: An Overview [Slides]

Deterministic neutron transport requires discretization of the Boltzmann transport equation in space, angle, energy, and time. Discretization in energy is typically performed with the multigroup approximation, which tries to preserve continuous energy cross section information by using a weighted average over discrete energy groups. There are two important requirements for accurate multigroup cross sections: appropriate energy group boundaries and an accurate weight function. The former can be selected with appropriate optimizers; the latter either requires flux solutions from comparable simulations or expert knowledge.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Conceptual Designs of the Structure of Inflatable Blades for Enabling Larger Turbines

Over the last couple of decades, increasingly larger rotor diameters have enabled significant reductions in the levelized cost of energy for wind through higher energy capture and improved capacity factors. But for onshore turbines, this has been met with manufacturing and transportation challenges. To enable larger onshore rotors, an innovative inflatable blade concept is investigated that employs both traditional and onsite manufacturing. The design architecture consists primarily of an inflatable aerodynamic shell attached to a factory-manufactured primary structure. Multiple architectures, cross-sectional topologies, and material combinations for the primary structure are investigated, as well as multiple skin materials. Structural cross-sectional characteristics are compared to a traditional blade, and inflatability and cost evaluations are presented. Results show that a box-beam architecture using only composite materials yields significant mass reduction with mature technologies/processes and modest cost decrease compared to traditional blade construction. This low-TRL study demonstrates the inflatable blade concept's techno-economic potential.

49 EE - Wind and Water Power Program - Wind (EE-4W↗
DOE OSTI2022

Friction Stir Welding – an Advanced Approach to Repair Nuclear Power Plant Components

Solid phase joining technique friction stir welding (FSW) has been shown to mitigate helium-related issues in fusion welding of irradiated steels. Here, we present detailed characterization results of the first friction stir weld of an irradiated 304L stainless steel (SS) coupon contained 5.2 atomic parts per million (appm) helium. Scanning electron microscopy (SEM) was used to characterize a cross section specimen removed from the friction stir weld. No macro helium induced crack was observed at the analyzed cross-section, and only 1 – 1.5 µm size pores were found in the stir zone (SZ) and the thermal-mechanical affected zone (TMAZ). Moreover, some minor helium aggregations (Maximum ~20 µm in length) appeared along grain boundaries inside the TMAZ. Thereafter, miniature tensile specimens were extracted from the SZ, TMAZ and heat affected zone (HAZ), and base metal (BM) and tested. All welded specimens showed high total elongations (> 60%) and strengths (> 75% BM strengths). Overall, the weld made by FSW showed much better results comparing with traditional fusion welding on irradiated SS.

Tang, Wei↗
DOE OSTI2022

Simulations of neutron noise in the research reactor AKR-2: comparison between a discrete ordinates and a diffusion-based method

A diffusion-based and a discrete ordinates method are used to simulate a neutron noise experiment in the research reactor AKR-2 at the Technical University in Dresden, Germany. The AKR-2 reactor provides an interesting case for the comparison between the two methods because it is characterized by large heterogeneities and regions with low macroscopic neutron cross-sections. For the calculations, the same spatial discretization and the same set of two-energy macroscopic neutron cross-sections with isotropic scattering are used. Significant discrepancies between the diffusion-based and discrete ordinates methods are found in regions of the systems where the diffusion approximation is expected to be inaccurate in reproducing characteristics of the static neutron flux and neutron noise. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2026

CFD Modeling of an 81" Single Slope Barrier Wall Drainage Window for on Grade and Sag Conditions

The main goal of this study is to design a drainage window in an 81" single slope barrier wall for on-grade and sag conditions that could replace the standard ODOT I-3 barrier catch basin. The ODOT design guidelines are as follows: a) Examine configurations of the opening to the flume behind the wall under the wall section to maximize conveyance of flow to a roadside ditch section. b) Examine window lengths and configurations to maximize hydraulic efficiency on a grade up to an absolute maximum window length of 20 ft. c) Use a minimum opening height of 4 in. and consider tapering to an increased height at the outlet to the flume to reduce the potential for debris clogging beneath the barrier section. On-grade locations are analyzed for longitudinal slope up to 5% and spread up to 10 ft. Sag locations, represented by pavement at zero longitudinal slope, are analyzed for water depths up to 18 in. The roadway cross section consists of a 10-ft shoulder at a 4.0% cross slope and pavement at a 1.6% cross slope. All surfaces are represented with Manning’s n = 0.015. Computational fluid dynamics (CFD) is used to perform the analysis. The modeling approach follows previous studies by the authors. The new design is similar to a slotted inlet: a rectangular opening cut into the bottom of a barrier (e.g., a temporary barrier or single slope barrier wall), which typically has a uniform cross section. Findings from laboratory tests of flow under Florida DOT barrier walls were used for additional validation of the modeling approach used in this study.

42 ENGINEERING↗
DOE OSTI2023

Freezing-in hadrophilic dark matter at low reheating temperatures

If the reheating temperature at the end of inflation is low, of order 10 MeV, then dark matter produced through ultraviolet freeze-in has a large direct detection cross section. We study such a scenario in which dark matter is hadrophilic. This leads to dark matter-nucleon scattering cross sections of interest for near-future experiments for dark matter masses in the range of 100 keV–100 MeV. We explore how these predictions vary if reheating is non-instantaneous.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Microstructural characterization of as-fabricated monolithic plates with boron carbide, aluminum boride, and zirconium boride burnable absorbers

The use of burnable absorbers can be beneficial for nuclear reactors by extending the fuel’s operational cycle, providing additional criticality control, and flattening the power profile. In this work, three burnable absorber materials (boron carbide, aluminum boride, and zirconium boride) embedded in aluminum have been fabricated into foils and clad in AA-6061 for potential use in high performance research reactors. The as-fabricated boron-containing phases were determined using transmission electron microscopy to be AlB2, B4C, and ZrB2. TEM also revealed weak bonding at the B4C-matrix interface. SEM showed a relatively uniform spatial distribution of boron-containing phases for all the candidate materials. Higher porosity was observed in the foil containing ZrB2 in its as-rolled condition. The porosity in the ZrB2 foil was reduced by hot isostatic pressing. The size and shape distributions of the boron-containing phases were analyzed on the criteria of cross-sectional area, perimeter, roundness, circularity, and aspect ratio. A method of converting the 2D burnable absorber dispersoids seen in cross-sectional microscopy images into 3D volumes was derived using both spherical and ellipsoidal geometry models. The difference in calculated burnable absorber dispersoid average volume between the two models ranges from 20% to 100%, which could impact burnable absorber burnout rates due to differences in neutron self-shielding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Measurement of material isotopics and atom number ratio with α-particle spectroscopy for a NIFFTE fission Time Projection Chamber actinide target

In this work, we present the results of a measurement of isotopic concentrations and atomic number ratio of a double-sided actinide target using α-spectroscopy and mass spectrometry. The double-sided actinide target, with predominantly 239 Pu on one side and 235 U on the other, was used in the fission Time Projection Chamber (fissionTPC) for a measurement of the neutron-induced fission cross-section ratio between the two isotopes. The measured atomic number ratio is needed to extract an absolute measurement fission cross-section ratio. The 239 Pu/ 235 U atom number ratio was measured with a combination of mass spectrometry and α-spectroscopy with a planar silicon detector achieving uncertainties of less than 1%. Different strategies for estimating isotopic concentration from the α-spectrum are presented to demonstrate the potential of these methods for non-destructive target assay. We found that a combination of fitting spectra with constraints from mass spectrometry, and summing counts in a region of the spectrum provided the most consistent results with the lowest uncertainty.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Search for heavy long-lived charged particles with level-1 trigger scouting data from proton-proton collisions at $\sqrt{s} = 13.6$ TeV

A search for heavy long-lived charged particles at the LHC is presented. Particles interacting with the CMS muon detector across several bunch crossings are searched for using a data sample of proton-proton collisions at $\sqrt{s}$ = 13.6 TeV collected with the CMS detector in 2024, corresponding to an integrated luminosity of 3.7 fb$^{-1}$. This is the first search relying on the novel level-1 trigger scouting data set collected without any trigger selection, allowing correlations between bunch crossings to be analyzed. The results are interpreted as upper limits on the cross sections of several benchmark processes with pair production of heavy long-lived charged particles. Upper limits on the fiducial cross section of a heavy long-lived charged particle with $p_\mathrm{T}$$\gt$ 500 GeV and $\lvertη\rvert$$\lt$ 0.83 are also set in different ranges of $β=v/c$. This analysis is a crucial proof of concept for the level-1 trigger data scouting system and complements existing searches for heavy long-lived charged particles by extending the sensitivity to lower $β$ values.

CMS↗
DOE OSTI2025

Incorporating Physical Priors into Weakly Supervised Anomaly Detection

We propose a new machine-learning-based anomaly detection strategy for comparing data with a background-only reference (a form of weak supervision). The sensitivity of previous strategies degrades significantly when the signal is too rare or there are many unhelpful features. Our prior-assisted weak supervision (PAWS) method incorporates information from a class of signal models to significantly enhance the search sensitivity of weakly supervised approaches. As long as the true signal is in the prespecified class, PAWS matches the sensitivity of a dedicated, fully supervised method without specifying the exact parameters ahead of time. On the benchmark LHC Olympics anomaly detection dataset, our mix of semisupervised and weakly supervised learning is able to extend the sensitivity over previous methods by a factor of 10 in cross section. Furthermore, if we add irrelevant (noise) dimensions to the inputs, classical methods degrade by another factor of 10 in cross section while PAWS remains insensitive to noise. This new approach could be applied in a number of scenarios and pushes the frontier of sensitivity between completely model-agnostic approaches and fully model-specific searches.

artificial neural networks↗
DOE OSTI2020

Interlaboratory Reproducibility of Contour Method Data Analysis and Residual Stress Calculation

While the contour method for residual stress assessment has developed rapidly, no published study documents its interlaboratory reproducibility. Objective: Here we report an initial reproducibility experiment focused on contour method data analysis and residual stress calculation. The experiment uses surface topography data from a physical process simulation of elastic-plastic beam bending. The simulation provides surface topography, for input to the contour method data analysis, as well as a known residual stress field with 130 MPa peak magnitude. Additionally, to increase realism, noise and specific artifacts are added to the topography data. A group of participants received the topography data (without the known residual stress), independently analyzed the data, and submitted results as a two-dimensional residual stress field. Analysis of submissions provides a group average residual stress field and the spatial distribution of reproducibility standard deviation. The group average residual stress agrees with the known stress in magnitude and spatial trend. The reproducibility standard deviation ranges from 2 to 54 MPa over the measurement plane, with an average of 5.4 MPa. Reproducibility standard deviation is smaller in the cross-section interior (≤ 5 MPa), modest near local extrema in the stress field (5 to 10 MPa), and larger near the cross-section boundaries (10 to 30 MPa). Overall, the largest values of reproducibility standard deviation (up to 54 MPa) occur in limited areas where artifacts had been added to the topography data; while some participants identified and removed these artifacts, some did not, leading to systematic differences that elevated the standard deviation.

42 ENGINEERING↗
DOE OSTI2024

Energy-resolved fast-neutron radiography using an event-mode neutron imaging detector

Energy-resolved fast-neutron radiography is a powerful non-destructive technique that can be used to remotely measure the quantity and distribution of elements and isotopes in a sample. This is done by comparing the energy-dependent neutron transmission of a sample with the known cross-sections of individual isotopes. The reconstruction of the composition is possible due to the unique features (e.g. resonances) in the cross-sections of individual isotopes. At short-pulsed (≲ 1 ns) neutron sources, such information is accessible via time-of-flight neutron imaging in principle, but requires a detector with nanosecond temporal resolution. Conventional neutron detectors can meet this requirement only by heavily compromising spatial resolution or efficiency. Here, we present a unique approach on fast neutron resonance radiography using a scintillator-based event-mode imaging detector at a short-pulsed neutron source, including first results on spatially mapped resonance profiles using MeV neutrons. The event mode approach applied in the presented detector allows recording of individual neutron interactions with nanosecond precision in time and sub-mm resolution in space. As a result, the entire available neutron energy spectrum can be measured for each pulse. At the same time, the use of a thick scintillator screen and lenses to focus the produced light results in a highly flexible field of view and a high interaction probability in the sensitive volume of the detector.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Constraining the impact of chlorine as a neutron absorber in next-gen fast reactor designs

The role of chlorine as a neutron poison and as a seed for producing radioactive waste in nuclear systems has driven a renewed interest to improve its nuclear data uncertainties. Additionally, basic and applied science programs that use CLYC (Cs 2 LiYCl 6 :Ce) detectors for neutron spectroscopy and monitoring are also very sensitive to any change in chlorine nuclear data for simulations of the detector response. In this work, sensitivities relevant for these different applications are addressed through simulations of the efficiency of CLYC detectors in a fast fission spectrum when applying new chlorine nuclear data as input. These simulations are validated by an experimental measurement using CLYC detectors coupled to an ionization chamber loaded with a 252 Cf spontaneous fission source. The results are then used to obtain the first reliable direct measurement of the 35 Cl(n,p 0 ) and summed Cl(n,p+n,α) fission spectrum average cross sections, found to be 54.7(32) and 105.0(98) mb, respectively. The results are within uncertainty of calculated fission spectrum averaged cross sections based on recently re-evaluated chlorine nuclear data, which confirm recent impact studies performed for the Molten Chloride Reactor Experiment. Meanwhile, there currently exists only one published criticality benchmark experiment that is sufficiently sensitive to chlorine nuclear data. Discrepancies are found with this set of criticality safety benchmarks, which are more sensitive to thermal and epithermal neutron energies than the energies, above 100 keV, tested in this current work. Hence, there is still a need to re-evaluate the chlorine nuclear data at lower energies to assess these discrepancies. Interpretation of the data from future “faster” criticality benchmarks, which are needed for next-gen fast reactor designs, benefit from the improved constraints on the chlorine nuclear data validated in this work.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Quantum scattering of HC 5 N and para -H 2 on a new potential energy surface

In the interstellar medium (ISM), non-local thermodynamic equilibrium situations are common due to low density, and one needs to consider the effect of molecular collisions in order to interpret the observations. Among the species detected in the ISM, cyanopolyynes, with the general molecular formula HC 2n+1 N (n = 1, 2, …), are characterized by large dipole moments and small rotational constants and constitute an indispensable class of candidates for the sensitive tracers of local density and temperature. We present a study of the collisional (de-) excitation of HC 5 N by para -H 2 (p-H 2 ) in its ground rotational state, namely HC 5 N ( j 1 ) + H 2 ( j 2 = 0) → HC 5 N (j$_1^′$) + H2 (j$_2^′$ = 0), where j 1 (or j$_1^′$) and j 2 (or j$_2^′$) denote the initial (or final) rotational quantum numbers of HC 5 N and H 2 , respectively. We performed the quantum scattering calculations at low collision energy using a new four-dimensional ab initio potential energy surface. In the regime where p-H 2 remains in its rotational ground state, converged cross sections did not require including excited rotational states of p-H 2 in the rotational basis. State-to-state cross sections were computed by means of the quantum-mechanical close-coupling (CC) method and the coupled states (CS) approximation, and rate coefficients for the first 61 levels of HC 5 N were computed for the first time up to 20 K with the CC approach and up to 50 K with the CS method. CC and CS results were found to agree well at temperatures up to 20 K. Finally, these data should allow a more accurate derivation of the HC 5 N abundance in molecular clouds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Constraining dark matter-proton scattering from molecular cloud ionization

Optically dense clouds in the interstellar medium composed predominantly of molecular hydrogen, known as molecular clouds, are sensitive to energy injection in the form of photon absorption, cosmic-ray scattering, and dark matter (DM) scattering. The ionization rates in dense molecular clouds are heavily constrained by observations of abundances of various molecular tracers. Recent studies have set constraints on the DM-electron scattering cross section using measurements of ionization rates in dense molecular clouds. Here we calculate the analogous bounds on the DM-proton cross section using the molecular Migdal effect, recently adapted from the neutron scattering literature to the DM context. These bounds may be the strongest limits on a strongly coupled DM subfraction, and represent the first application of the Migdal effect to astrophysical systems. Published by the American Physical Society 2024

Astronomy & Astrophysics↗