Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Compressive limiters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Development of a medium-duty stoichiometric diesel micro-pilot natural gas engine

Fueling a compression-ignition engine with premixed natural gas offers the potential to combine a clean-burning, low-carbon fuel with a high compression ratio, high-efficiency engine. This work describes the development of a multi-cylinder 6.7 L diesel engine converted to run stoichiometric diesel micro-pilot/ natural gas premix combustion with a maximum diesel contribution target of 5% of the total fuel energy and a three-way catalyst aftertreatment system. Results are given by comparing the stoichiometric combustion to the diesel baseline operation, showing combustion characteristics differences, including the rapid two stage heat release. A high load output of 23 bar brake mean effective pressure was obtained with diesel-like brake thermal efficiency of 41%. This operating condition enabled a brake specific CO 2 emissions reduction of up to 25% when compared to diesel. It was observed that the low load output is limited by combustion stability when operated at stoichiometric condition. The three-way catalyst is observed to run at peak efficiency with an equivalence ratio of 1.01. Injector fouling was observed through the inspection of the nozzle and its internal parts, indicating carbon build-up similar to that seen in injector coking mechanisms. A comparison of the developed engine to other engine technologies is given, showing that the diesel micro-pilot natural gas engine performance is in good standing among other diesel and gas engines in the market.

Engineering↗

Investigations of Dual-Purpose Canister Direct Disposal Feasibility (FY14)

Results reported here continue to support the FY13 conclusion that direct disposal of DPCs is technically feasible, at least for some DPCs, and for some disposal concepts (geologic host media). Much of the work performed has reached a point where site-specific information would be needed for further resolution. Several activities in FY14 have focused on clay/shale media because of potential complications resulting from low thermal conductivity, limited temperature tolerance, and the need to construct hundreds of kilometers of emplacement drifts that will remain stable for at least 50 years. Technologies for rapid excavation and liner installation have significantly advanced in the past 20 years. Tunnel boring machines are the clear choice for large-scale excavation. The first TBM excavations, including some constructed in clay or shale media, are now approaching 50 years of service. Open-type TBMs are a good choice but the repository host formation would need to have sufficient compressive strength for the excavation face to be self-supporting. One way to improve the strength-stress relationship is to reduce the repository depth in soft formations (e.g., 300 m depth). The fastest construction appears to be possible using TBMs with a single-pass liner made of pre-fabricated concrete segments. Major projects have been constructed with prefabricated segmented liner systems, and with cast-in-place concrete liners. Cost comparisons show that differences in project management and financing may be larger cost factors than the choice of liner systems. Costs for large-scale excavation and construction in clay/shale media vary widely but can probably be limited to $10,000 per linear meter, which is similar to previous estimates for repository construction. Concepts for disposal of DPC-based waste packages in clay/shale media are associated with thermal management challenges because of the relatively low thermal conductivity and limited temperature tolerance. Peak temperature limits of 100°C or lower for clay-rich materials have been selected by some international programs, but a limit above 100°C could help to shorten the duration of surface decay storage and repository ventilation. The effects of locally higher peak temperatures on repository performance need to be evaluated (in addition to the effects at lower temperatures). This report describes a modeling approach that couples the TOUGH2 and FLAC3D codes to represent thermally driven THM processes, as a demonstration of the types of models needed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Characterization of Static Recrystallization of a Ni-Cr-Mo-Based C276 Superalloy in Two-Stage Isothermal Compression

In order to clarify the microstructure evolution characteristics during holding period after slight degree of deformation for a Ni-Cr-Mo-based C276 superalloy, two-stage isothermal compression tests have been performed at the temperature range of 1000-1150 °C and the strain rate range of 0.1-5 s{sup −1}. The stress–strain curves and microstructure observation infer that both static recovery (SRV) and static recrystallization (SRX) took place during the holding period when the specimens were deformed at 1100-1150 °C and only SRV occurred in the specimens that deformed at the temperatures lower than 1100 °C. The softening effects increase with the increasing temperature and deformation degree, while the influence of strain rate seems less pronounced because of the limited stored energy resulted from the small deformation. The grain boundary characteristics, analyzed using electron backscatter diffraction technique, indicate that high densities of twins and Σ3 grain boundaries form associated with the nucleation and growth of SRX grains. Finally, the recrystallization during and after deformation, i.e., dynamic recrystallization, SRX and metadynamic recrystallization, was discussed concurrently.

36 MATERIALS SCIENCE↗

Compliant Intramedullary Stems for Joint Reconstruction

The longevity of current joint replacements is limited by aseptic loosening, which is the primary cause of non-infectious failure for hip, knee, and ankle arthroplasty. Aseptic loosening is typically caused either by osteolysis from particulate wear, or by high shear stresses at the bone-implant interface from over-constraint. Our objective was to demonstrate feasibility of a compliant intramedullary stem that eliminates over-constraint without generating particulate wear. The compliant stem is built around a compliant mechanism that permits rotation about a single axis. We first established several models to understand the relationship between mechanism geometry and implant performance under a given angular displacement and compressive load. We then used a neural network to identify a design space of geometries that would support an expected 100-year fatigue life inside the body. We additively manufactured one representative mechanism for each of three anatomic locations, and evaluated these prototypes on a KR-210 robot. The neural network predicts maximum stress and torsional stiffness with 2.69% and 4.08% error respectively, relative to finite element analysis data. We identified feasible design spaces for all three of the anatomic locations. Simulated peak stresses for the three stem prototypes were below the fatigue limit. Benchtop performance of all three prototypes was within design specifications. Our results demonstrate the feasibility of designing patient- and joint-specific compliant stems that address the root causes of aseptic loosening. Guided by these results, we expect the use of compliant intramedullary stems in joint reconstruction technology to increase implant lifetime.

60 APPLIED LIFE SCIENCES↗

Extrusion compression molded critical rare earth free bonded permanent magnets

Samarium iron nitride (Sm-Fe-N) bonded magnets have emerged as promising candidates for various industrial applications due to their exceptional magnetic properties. Compounds with magnetic material 95 wt fraction (wt.%) (∼74 vol%) and 97 wt.% (∼81 vol%) of SmFeN in a polyamide (PA12) polymer binder are manufactured using a batch mixer followed by compression molding. A maximum energy product ( BH ) max of 186.21 kJ.m -3 (23.4 MGOe) is achieved in the 95 wt.% bonded magnets; 97 wt.% magnets had a ( BH ) max of 165.52 kJ.m -3 (20.8 MGOe). It is found that the degree of alignment (DoA) of 99 % is achieved in the 95 wt.% magnets, whereas the 97 wt.% magnets are limited to a DoA of 90 % respectively. The high DoA can be attributed to low particle-particle interaction during the post-magnetic field alignment process. Finally, this research provides a useful insight of binder-particle interactions at very high magnet weight fractions and their effect on magnetic strength and performance.

36 MATERIALS SCIENCE↗

Deterministic switching of hierarchy during wrinkling in quasi-planar bilayers

Emergence of hierarchy during compression of quasi-planar bilayers is preceded by a mode-locked state during which the quasi-planar form persists. Transition to hierarchy is determined entirely by geometrically observable parameters. This results in a universal transition phase diagram that enables one to deterministically tune hierarchy even with limited knowledge about material properties.

36 MATERIALS SCIENCE↗

Hydrogen-Steam Separation Using Mechanical Vapor Recompression Cycle

Solar thermochemical hydrogen and fuel production is a promising pathways for producing sustainable fuels and chemicals. One of the main challenges in the development of these systems is their low steam conversion extent, dictated by its restrictive thermodynamics requiring extremely high temperatures and low oxygen partial pressure to obtain conversions over 10 \%. While condensing the unreacted steam is technically simple, the latent heat is thus lost, which can be larger than the producd hydrogen higher heating value. We propose to use a modified mechanical vapor recompression cycle, allowing to recover the latent heat by compressing the steam-hydrogen mixture prior to the condensation process, thus creating a temperature different between the hot exhaust and cold inlet streams. We show that this method can recover over 90 % of the latent heat, thus increasing the viability of solar thermochemical hydrogen production cycles even under limited conversion conditions.

hydrogen technology↗

The Ammonia-Hydrogen System under Pressure

Binary mixtures of hydrogen and ammonia were compressed in diamond anvil cells to 15 GPa at room temperature over a range of compositions. The phase behavior was characterized using optical microscopy, Raman spectroscopy, and synchrotron X-ray diffraction. Below 1.2 GPa we observed two-phase coexistence between liquid ammonia and fluid hydrogen phases with limited solubility of hydrogen within the ammonia-rich phase. Complete immiscibility was observed subsequent to the freezing of ammonia phase III at 1.2 GPa, although hydrogen may become metastably trapped within the disordered face-centered-cubic lattice upon rapid solidification. For all compositions studied, the phase III to phase IV transition of ammonia occurred at ~3.8 GPa and hydrogen solidified at ~5.5 GPa, transition pressures equivalent to those observed for the pure components. A P-x phase diagram for the NH 3 -H 2 system is proposed on the basis of these observations with implications for planetary ices, molecular compound formation, and possible hydrogen storage materials.

08 HYDROGEN↗

Coupling of dust acoustic and shear mode through velocity shear in a strongly coupled dusty plasma

In the strongly coupled limit, the generalized hydrodynamic model shows that a dusty plasma, acquiring significant rigidity, is able to support a “shear” like mode. It is being demonstrated here that in presence of velocity shear gradient, this shear like mode gets coupled with the dust acoustic mode which is generated by the compressibility effect of the dust fluid due to the finite temperatures of the dust, electron, and ion fluids. In the local analysis, the dispersion relation shows that velocity shear gradient not only couples the two modes but is also responsible for the instabilities of that coupled mode which is confirmed by nonlocal analysis with numerical techniques.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A comparison of Raman and pyrometry dynamic temperature measurements of shocked cyclohexane

Optical pyrometry is a well-developed, broadly applicable method to determine temperature in dynamic compression experiments. However, it measures radiation from only the skin depth of the radiant material, is highly susceptible to spurious backgrounds, and requires an often-unmeasurable free parameter—the sample dynamic emissivity. Raman spectroscopy offers a method to determine temperature directly from fundamental theory, but it is practically limited in applications to a small subset of shock experiments. In this work, we describe an experiment allowing simultaneous application of Raman and pyrometric temperature techniques to benchmark a specific instance of pyrometry. We attempted both measurements on multiple experiments and compare the successful temperature results between the separate but highly repeatable shots. Here, we find that dynamic shock temperatures inferred from Raman spectroscopy and pyrometry generally agree within the uncertainties of each measurement, although those uncertainties are larger than typical for a specially designed pyrometry experiment on a shocked metal sample.

74 ATOMIC AND MOLECULAR PHYSICS↗

Development and validation of a new guidance device for lateral approach stereotactic breast biopsy

Stereotactic breast biopsy (SBB) is the gold standard for minimally invasive breast cancer diagnosis. Current systems rely on one of two methods for needle insertion: A vertical approach (perpendicular to the breast compression plate) or a lateral approach (parallel to the compression plate). While the vertical approach is more frequently used, it is not feasible in patients with thin breasts (<3 cm thick after compression) or with superficial lesions. Further, existing SBB guidance hardware provides at most one degree of rotational freedom in the needle trajectory, and as such requires a separate skin incision for each biopsy target. The authors present a new design of lateral guidance device for SBB, which addresses the limitations of the vertical approach and provides improvements over the existing lateral guidance hardware. Specifically, the new device provides (1) an adjustable rigid needle support to minimize needle deflection within the breast and (2) an additional degree of rotational freedom in the needle trajectory, allowing the radiologist to sample multiple targets through a single skin incision. This device was compared to a commercial lateral guidance device in a series of phantom experiments. Needle placement error using each device was measured in agar phantoms for needle insertions at lateral depths of 2 and 5 cm. The biopsy success rate for each device was then estimated by performing biopsy procedures in commercial SBB phantoms. SBB performed with the new lateral guidance device provided reduced needle placement error relative to the commercial lateral guidance device (0.89{+-}0.22 vs 1.75{+-}0.35 mm for targets at 2 cm depth; 1.94{+-}0.20 vs 3.21{+-}0.31 mm for targets at 5 cm depth). The new lateral guidance device also provided improved biopsy accuracy in SBB procedures compared to the commercial lateral guidance device (100% vs 58% success rate). Finally, experiments were performed to demonstrate that the new device can accurately sample lesions within thin breast phantoms and multiple lesions through a single incision point. This device can be incorporated directly into the clinical SBB procedural workflow, with no additional electrical hardware, software, postprocessing, or image analysis.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

MO-A-BRD-01: An Investigation of the Dynamic Response of a Novel Acousto-Optic Liquid Crystal Detector for Full-Field Transmission Ultrasound Breast Imaging

Purpose: To characterize the dynamic response of a novel acousto-optic (AO) liquid crystal detector for high-resolution transmission ultrasound breast imaging. Transient and steady-state lesion contrast were investigated to identify optimal transducer settings for our prototype imaging system consistent with the FDA limits of 1 W/cm{sup 2} and 50 J/cm{sup 2} on the incident acoustic intensity and the transmitted acoustic energy flux density. Methods: We have developed a full-field transmission ultrasound breast imaging system that uses monochromatic plane-wave illumination to acquire projection images of the compressed breast. The acoustic intensity transmitted through the breast is converted into a visual image by a proprietary liquid crystal detector operating on the basis of the AO effect. The dynamic response of the AO detector in the absence of an imaged breast was recorded by a CCD camera as a function of the acoustic field intensity and the detector exposure time. Additionally, a stereotactic needle biopsy breast phantom was used to investigate the change in opaque lesion contrast with increasing exposure time for a range of incident acoustic field intensities. Results: Using transducer voltages between 0.3 V and 0.8 V and exposure times of 3 minutes, a unique one-to-one mapping of incident acoustic intensity to steady-state optical brightness in the AO detector was observed. A transfer curve mapping acoustic intensity to steady-state optical brightness shows a high-contrast region analogous to the linear portion of the Hurter-Driffield curves of radiography. Using transducer voltages between 1 V and 1.75 V and exposure times of 90 s, the lesion contrast study demonstrated increasing lesion contrast with increasing breast exposure time and acoustic field intensity. Lesion-to-background contrast on the order of 0.80 was observed. Conclusion: Maximal lesion contrast in our prototype system can be obtained using the highest acoustic field intensity and the longest breast exposure time allowable under FDA standards. Department of Defense (DOD) Breast Cancer Research Program IDEA Award W81XWH-11-1-0332; National Institutes of Health (NIH) Grant T32 EB002103-21 from the National Institute of Biomedical Imaging and Bioengineering (NIBIB)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The high-foot implosion campaign on the National Ignition Facility

If you could identify only one key skill that a primary or secondary designer should possess, it would be the ability to design an implosion that works reliably and as advertised. Being able to harness an implosion is a key skill because of what an implosion does – an implosion is a “pressure amplifier” that takes absorbed energy and turns that energy, with significant energy loss, into pressure. The pressure generated in implosions is used to compress materials to high densities in the primary designers case, and high densities and temperatures in the secondary designers case. While primary designers and their simulation tools can be tested against experiments at scale fielded at high-explosive facilities around the NNSA complex, secondary designers are much more limited in the experimental facilities that can access relevant conditions (facilities such as Omega at the Laboratory for Laser Energetics, the Z-machine at Sandia National Lab in Albuquerque and the National Ignition Facility at Livermore are more-or-less it). Ignition conditions are the highest-pressure and therefore hardest conditions to access with facility levels of energy, but the struggle to obtain ignition has been an illuminating test of the stockpile stewardship model. If you thought the criteria for ignition is when the fusion energy output from an inertially confined fusion (ICF) implosion exceeds the energy delivered to the target, you’d be wrong. While the above definition is used for milestone tracking purposes, the actually definition of ignition that has been used in fusion research since 1957 is when the power produced by the fusing region exceeds the rate at which energy is lost from the fusing region due to x-ray radiation processes and heat conduction processes. This simple statement about fusion power and rates of energy loss lead to a quantitative criterion for ignition that is known as the “Lawson Criteria.”

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Research and Development Needs to Enable Expansion of Natural Gas Use in Transportation

In the transportation sector, users are taking a new look at natural gas (NG) as an affordable alternative, often priced at $1.50-2.00/gasoline gallon equivalent (GGE) less than gasoline or diesel, and offering potential societal benefits like reductions in petroleum use, air pollutant emissions, and greenhouse gas (GHG) emissions. Unlike petroleum, a significant portion of which is imported and vulnerable to external disruptions at key points in the supply chain, NG is almost completely domestic and supplies are diverse. NG from renewable sources like landfills and anaerobic digesters or from fossil sources like shale gas is found in nearly every state, with associated benefits for state economies. An extensive transmission and distribution infrastructure exists in much of the country. There are, however, significant barriers that limit the speed and breadth of NG uptake into the transportation sector. Many of the barriers to NG use in this sector are technical in nature and overcoming them will require a concerted R&D effort. This paper focuses on those barriers and associated R&D opportunities for using compressed natural gas (CNG), liquefied natural gas (LNG), and NG-derived liquid fuels in internal combustion engines (ICEs) for light duty vehicle (LDV) and medium- and heavy-duty truck (M/HDT) applications. This paper is organized into five key areas that highlight R&D needs: NG distribution, liquid fuel production from stranded gas, vehicle fuel use, NG storage, and impact analysis and assessment.

03 NATURAL GAS↗

Forward slanted slot throat stability bypass to increase the stable airflow range of a Mach 2.5 inlet with 60 percent internal contraction

The results of an experimental investigation to increase the stable airflow operating range of a supersonic mixed-compression inlet are presented. Two forward-slanted slot stability-bypass entrance configurations were tested. In terms of diffuser-exit corrected airflow, a large inlet stable airflow range of 18.5 percent was obtained with the superior configuration if a constant pressure was maintained in the bypass plenum. Limited unstart angle-of-attack data are presented.

Shaw, R. J.↗

The comparative performance of superchargers

This report presents a comparison of superchargers on the basis of the power required to compress the air at a definite rate, and on the basis of the net engine power developed at altitudes from 0 to 40,000 feet. The investigation included geared centrifugal, turbine-driven centrifugal, roots, and vane-type superchargers. It also includes a brief discussion of the mechanical limitations of each supercharger and explains how the method of control affects the power requirements.

Schey, Oscar W↗

Application of symbolic and algebraic manipulation software in solving applied mechanics problems

As its name implies, symbolic and algebraic manipulation is an operational tool which not only can retain symbols throughout computations but also can express results in terms of symbols. This report starts with a history of symbolic and algebraic manipulators and a review of the literatures. With the help of selected examples, the capabilities of symbolic and algebraic manipulators are demonstrated. These applications to problems of applied mechanics are then presented. They are the application of automatic formulation to applied mechanics problems, application to a materially nonlinear problem (rigid-plastic ring compression) by finite element method (FEM) and application to plate problems by FEM. The advantages and difficulties, contributions, education, and perspectives of symbolic and algebraic manipulation are discussed. It is well known that there exist some fundamental difficulties in symbolic and algebraic manipulation, such as internal swelling and mathematical limitation. A remedy for these difficulties is proposed, and the three applications mentioned are solved successfully. For example, the closed from solution of stiffness matrix of four-node isoparametrical quadrilateral element for 2-D elasticity problem was not available before. Due to the work presented, the automatic construction of it becomes feasible. In addition, a new advantage of the application of symbolic and algebraic manipulation found is believed to be crucial in improving the efficiency of program execution in the future. This will substantially shorten the response time of a system. It is very significant for certain systems, such as missile and high speed aircraft systems, in which time plays an important role.

Tsai, Wen-Lang↗

Obstetrical Forceps Would Limit Force On An Infant's Head

Improved obstetrical forceps proposed to reduce injuries to newborn infants. Fabricated mostly of thermoplastic material. Reinforcing fibers added in hinge region of forceps. Combination of material, size, and shape chosen to make forceps yield elastically by amount keeping applied force from rising beyond maximum allowable value. Fiber-optic sensors for measuring strains embedded in forceps. Strain measurements used to compute tensile and compressive forces applied to infant's head.

Smeltzer, Stan↗