Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPATIBILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

In Vivo Dosimetry of High-Dose-Rate Interstitial Brachytherapy in the Pelvic Region: Use of a Radiophotoluminescence Glass Dosimeter for Measurement of 1004 Points in 66 Patients With Pelvic Malignancy

Purpose: To perform the largest in vivo dosimetry study for interstitial brachytherapy yet to be undertaken using a new radiophotoluminescence glass dosimeter (RPLGD) in patients with pelvic malignancy and to study the limits of contemporary planning software based on the results. Patients and Methods: Sixty-six patients with pelvic malignancy were treated with high-dose-rate interstitial brachytherapy, including prostate (n = 26), gynecological (n = 35), and miscellaneous (n = 5). Doses for a total of 1004 points were measured by RPLGDs and calculated with planning software in the following locations: rectum (n = 549), urethra (n = 415), vagina (n = 25), and perineum (n = 15). Compatibility (measured dose/calculated dose) was analyzed according to dosimeter location. Results: The compatibility for all dosimeters was 0.98 {+-} 0.23, stratified by location: rectum, 0.99 {+-} 0.20; urethra, 0.96 {+-} 0.26; vagina, 0.91 {+-} 0.08; and perineum, 1.25 {+-} 0.32. Conclusions: Deviations between measured and calculated doses for the rectum and urethra were greater than 20%, which is attributable to the independent movements of these organs and the applicators. Missing corrections for inhomogeneity are responsible for the 9% negative shift near the vaginal cylinder (specific gravity = 1.24), whereas neglect of transit dose contributes to the 25% positive shift in the perineal dose. Dose deviation of >20% for nontarget organs should be taken into account in the planning process. Further development of planning software and a real-time dosimetry system are necessary to use the current findings and to achieve adaptive dose delivery.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Magnetic Resonance Imaging Protocol Optimization for Delineation of Gross Tumor Volume in Hypopharyngeal and Laryngeal Tumors

Purpose: To optimize the use of MRI for delineation of gross tumor volume for radiotherapy treatment planning purposes in hypopharyngeal and laryngeal tumors. Methods and Materials: Magnetic resonance images (T1 weighted and T2 weighted) of a healthy volunteer were acquired using a 1.5 T and 3.0 T MR scanner. Various receiver coils were investigated that were compatible with the immobilization mask needed for reliable coregistration with computed tomography data. For the optimal receiver coil, the influence of resolution, slice thickness, and strength of magnetic field on the signal-to-noise ratio (SNR) was studied. Feasibility of the definitive protocol was tested on patients with hypopharyngeal (n = 19) and laryngeal (n = 42) carcinoma. Results: Large differences in SNR were obtained for the various coils. The SNR values obtained using surface coils that were compatible with the immobilization mask were three times higher than those obtained using a standard head-and-neck coil and five times higher than those obtained using a body coil. High-resolution images (0.4 x 0.4 x 4 mm{sup 3}) showed superior anatomic detail and resulted in a 4-min scan time. Image quality at 3.0 T was not significantly better compared with 1.5 T. In 3 patients the MR study could not be performed; for 5 patients images were severely deteriorated by motion artefacts. High-quality MR images were obtained in 53 patients. Conclusions: High-resolution MR images of the hypopharynx and larynx can be obtained in the majority of patients using surface receiver coils in combination with the radiotherapy mask. These MR images can be successfully used for tumor delineation in radiotherapy.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Microscopic Gold Particle-Based Fiducial Markers for Proton Therapy of Prostate Cancer

Purpose: We examined the feasibility of using fiducial markers composed of microscopic gold particles and human-compatible polymers as a means to overcome current problems with conventional macroscopic gold fiducial markers, such as dose reduction and artifact generation, in proton therapy for prostate cancer. Methods and Materials: We examined two types of gold particle fiducial marker interactions: that with diagnostic X-rays and with a therapeutic proton beam. That is, we qualitatively and quantitatively compared the radiographic visibility of conventional gold and gold particle fiducial markers and the CT artifacts and dose reduction associated with their use. Results: The gold particle fiducials could be easily distinguished from high-density structures, such as the pelvic bone, in diagnostic X-rays but were nearly transparent to a proton beam. The proton dose distribution was distorted <5% by the gold particle fiducials with a 4.9% normalized gold density; this was the case even in the worst configuration (i.e., parallel alignment with a single-direction proton beam). In addition, CT artifacts were dramatically reduced for the gold particle mixture. Conclusion: Mixtures of microscopic gold particles and human-compatible polymers have excellent potential as fiducial markers for proton therapy for prostate cancer. These include good radiographic visibility, low distortion of the depth-dose distribution, and few CT artifacts.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Optical tomography reconstruction algorithm with the finite element method: An optimal approach with regularization tools

Highlights: •New strategies to improve the accuracy of the reconstruction through mesh and finite element parameterization. •Use of gradient filtering through an alternative inner product within the adjoint method. •An integral form of the cost function is used to make the reconstruction compatible with all finite element formulations, continuous and discontinuous. •Gradient-based algorithm with the adjoint method is used for the reconstruction. -- Abstract: Optical tomography is mathematically treated as a non-linear inverse problem where the optical properties of the probed medium are recovered through the minimization of the errors between the experimental measurements and their predictions with a numerical model at the locations of the detectors. According to the ill-posed behavior of the inverse problem, some regularization tools must be performed and the Tikhonov penalization type is the most commonly used in optical tomography applications. This paper introduces an optimized approach for optical tomography reconstruction with the finite element method. An integral form of the cost function is used to take into account the surfaces of the detectors and make the reconstruction compatible with all finite element formulations, continuous and discontinuous. Through a gradient-based algorithm where the adjoint method is used to compute the gradient of the cost function, an alternative inner product is employed for preconditioning the reconstruction algorithm. Moreover, appropriate re-parameterization of the optical properties is performed. These regularization strategies are compared with the classical Tikhonov penalization one. It is shown that both the re-parameterization and the use of the Sobolev cost function gradient are efficient for solving such an ill-posed inverse problem.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A quadratic programming flux correction method for high-order DG discretizations of S transport

In this work, we present a new flux-fixup approach for arbitrarily high-order discontinuous Galerkin (DG) discretizations of the S N transport equation, and we demonstrate the compatibility of this approach with the Variable Eddington Factor (VEF) method. The new fixup approach is sweep-compatible: during a transport sweep (block Gauss-Seidel iteration in which the scattering source is lagged), a local quadratic programming (QP) problem is solved in each spatial element to ensure that the solution satisfies certain physical constraints, including local particle balance. In this paper, we describe two choices of physical constraints, resulting in two variants of the method: QP Zero (QPZ) and QP Maximum Principle (QPMP). In QPZ, the finite element coefficients of the solution are constrained to be nonnegative. In QPMP, they are constrained to adhere to an approximate discrete maximum principle. There are two primary takeaways in this paper. First, when the positive Bernstein basis is used for DG discretization, the QPMP method eliminates negativities, preserves high-order accuracy for smooth problems, and significantly dampens unphysical oscillations in the solution. The latter feature – the dampening of unphysical oscillations – is an improvement upon standard, simpler fixup approaches such as the approach described in (denoted as the “zero and rescale” (ZR) method in this paper). This improvement comes at a moderate computational cost, but it is not prohibitive. Our results show that, even in an unrealistic worst-case scenario where 83% of the spatial elements require a fixup, the computational cost of performing a transport sweep with fixup is only ~31% greater than performing one without fixup. The second takeaway is that the VEF method can be used to accelerate the convergence of transport sweeps even when a fixup is applied. When optically thick regions are present, transport sweeps converge slowly, regardless of whether a fixup is applied, and acceleration is needed. However, attempting to apply standard diffusion synthetic acceleration (DSA) to fixed-up transport sweeps results in divergence for optically thick problems. Our results show that the same is not true for VEF. When VEF is combined with fixed-up transport sweeps, the result is a scheme that produces a nonnegative solution, converges independently of the mean free path, and, in the case of the QPMP fixup, adheres to an approximate discrete maximum principle.

97 MATHEMATICS AND COMPUTING↗

Towards sharp error analysis of extended Lagrangian molecular dynamics

The extended Lagrangian molecular dynamics (XLMD) method provides a useful framework for reducing the computational cost of a class of molecular dynamics simulations with constrained latent variables. The XLMD method relaxes the constraints by introducing a fictitious mass ε for the latent variables and solving a set of singularly perturbed ordinary differential equations. While favorable numerical performance of XLMD has been demonstrated in several different contexts in the past decade, mathematical analysis of the method remains scarce. Here, we propose the first error analysis of the XLMD method in the context of a classical polarizable force field model. While the dynamics with respect to the atomic degrees of freedom are general and nonlinear, the key mathematical simplification of the polarizable force field model is that the constraints on the latent variables are given by a linear system of equations. We prove that when the initial value of the latent variables is compatible in a sense that we define, XLMD converges as the fictitious mass ε is made small with $\mathscr{O}$(ε) error for the atomic degrees of freedom and with $\mathscr{O}$($\sqrt{ε}$) error for the latent variables, when the dimension of the latent variable d' is 1. Furthermore, when the initial value of the latent variables is improved to be optimally compatible in a certain sense, we prove that the convergence rate can be improved to $\mathscr{O}$(ε) for the latent variables as well. Numerical results verify that both estimates are sharp not only for d'=1, but also for arbitrary d'. In the setting of general d', we do obtain convergence, but with the non-sharp rate of $\mathscr{O}$($\sqrt{ε}$) for both the atomic and latent variables.

74 ATOMIC AND MOLECULAR PHYSICS↗

Multiscale graph neural network autoencoders for interpretable scientific machine learning

The goal of this work is to address two limitations in autoencoder-based models: latent space interpretability and compatibility with unstructured meshes. This is accomplished here with the development of a novel graph neural network (GNN) autoencoding architecture with demonstrations on complex fluid flow applications. To address the first goal of interpretability, the GNN autoencoder achieves reduction in the number nodes in the encoding stage through an adaptive graph reduction procedure. Further, this reduction procedure essentially amounts to flowfieldconditioned node sampling and sensor identification, and produces interpretable latent graph representations tailored to the flowfield reconstruction task in the form of so-called masked fields. These masked fields allow the user to (a) visualize where in physical space a given latent graph is active, and (b) interpret the time-evolution of the latent graph connectivity in accordance with the time-evolution of unsteady flow features (e.g. recirculation zones, shear layers) in the domain. To address the goal of unstructured mesh compatibility, the autoencoding architecture utilizes a series of multi-scale message passing (MMP) layers, each of which models information exchange among node neighborhoods at various lengthscales. The MMP layer, which augments standard single-scale message passing with learnable coarsening operations, allows the decoder to more efficiently reconstruct the flowfield from the identified regions in the masked fields. Analysis of latent graphs produced by the autoencoder for various model settings are conducted using unstructured snapshot data sourced from large-eddy simulations in a backward-facing step (BFS) flow configuration with an OpenFOAM-based flow solver at high Reynolds numbers.

97 MATHEMATICS AND COMPUTING↗

A combined experimental and crystal plasticity study of grain size effects in magnesium alloys

This work presents a method to incorporate the micro Hall-Petch equation into the crystal plasticity finite element (CPFE) framework accounting for the microstructural features to understand the coupling between grain size, texture, and loading direction in magnesium alloys. The effect of grain size and texture is accounted for by modifying the slip resistances of individual basal and prismatic systems based on the micro Hall-Petch equation. The modification based on the micro Hall-Petch equation endows every slip system at each microstructural point with a slip system-level grain size and maximum compatibility factor, which are in turn used to modify the slip resistance. While the slip-system level grain size is a measure of the grain size, the maximum compatibility factor encodes the effect of the grain boundary on the slip system resistance modification and is computed based on the Luster-Morris factor. The model is calibrated using experimental stress-strain curves of Mg-4Al samples with three different grain sizes from which the Hall-Petch coefficients are extracted and compared with Hall-Petch coefficients predicted using original parameters from previous work. The predictability of the model is then evaluated for a Mg-4Al sample with different texture and three grain sizes subjected to loading in different directions. The calibrated parameters are then used for some parametric studies to investigate the variation of Hall-Petch slope for different degrees of simulated spread in basal texture, variation of Hall-Petch slope with loading direction relative to basal poles for a microstructure with strong basal texture, and variation of yield strength with change in grain morphology. The proposed approach to incorporate the micro Hall-Petch equation into the CPFE framework provides a foundation to quantitatively model more complicated scenarios of coupling between grain size, texture and loading direction in the plasticity of Mg alloys.

Crystal plasticity↗

Performance of U 3 Si 2 in an LWR following a cladding breach during normal operation

High-density fuels have been proposed as a possible replacement for uranium-dioxide as a fuel for light water reactors (LWRs) due to their increased loading of fissionable material. The objectives of this proposal are (1) to increase reactor cycle length and reactor power, and (2) to offset any neutronic penalty associated with advanced cladding systems. Of the high-density fuels under consideration, there is particular interest in triuranium disilicide (U 3 Si 2 ) due to its increased metal density and favorable thermal properties as compared to UO 2 . However, there are concerns regarding the chemical compatibility of U 3 Si 2 with water and steam as used for LWR coolant.This paper summarizes research on fuel-coolant chemical compatibility for UO 2 LWR fuel during a cladding breach and highlights that generally, because of its chemical inertness, UO 2 -coolant reactions are of little consequence to reactor operation. However, the volumetric expansion associated with the reaction of UO 2 and oxygen is a concern for possible conditions encountered during air ingress of dry storage. These same concerns arise for U 3 Si 2 , which exhibits greater volumetric expansion than UO 2 when exposed to water or steam. These reactions ultimately result in increased fuel volume that the cladding must accommodate, as well as additional heat generated as the fuel reacts.The BISON fuel performance code was used to perform a comparative analysis on the behavior of UO 2 and U 3 Si 2 under normal operation. Silicide fuel simulations were then extended to demonstrate how varying thermodynamic and chemical kinetics influence fuel expansion and subsequent cladding performance during a cladding breach. These simulations were further extended to a 3D subsection of a fuel rod to demonstrate the characteristics of the resulting cladding crack.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Composite blend polymer membranes with increased proton selectivity and lifetime for vanadium redox flow batteries

Composite membranes based on sulfonated fluorinated poly(arylene ether) (SFPAE) and poly(vinylidene fluoride-co-hexafluoropropene) (P(VDF-co-HFP)) were prepared with various contents of P(VDF-co-HFP) for vanadium redox flow battery (VRFB) applications. The compatibility and interaction of SFPAE and P(VDF-co-HFP) were characterized by atomic force microscopy, differential scanning calorimetry, and Fourier transform infrared spectroscopy. The water uptake, mechanical properties, thermal property, proton conductivity, VO2+ permeability and cell performance of the composite membranes were investigated in detail and compared to the pristine SFPAE membrane. It was found that SFPAE had good compatibility with P(VDF-co-HFP) and the incorporation of P(VDF-co-HFP) increased the mechanical properties, thermal property, and proton selectivity of the materials effectively. An SFPAE composite membrane with 10 wt.% P(VDF-co-HFP) exhibited a 44% increase in VRFB cell lifetime as compared to a cell with a pure SFPAE membrane. Therefore, the P(VDF-co-HFP) blending approach is a facile method for producing low-cost, high-performance VRFB membranes.

composite↗

On the magnetic structure of DyNiO{sub 3}

The crystallographic structure of DyNiO{sub 3} has been investigated at T=200, 100, and 2 K from high-resolution neutron powder diffraction (NPD) data. We show that the structure is monoclinic, space group P2{sub 1}/n, from the metal-insulator transition temperature at T{sub MI}=564 K down to 2 K. The Ni atoms occupy two different sites 2d (Ni1) and 2c (Ni2), whose valences, estimated from bond-valence consideration, are +2.43(1) and +3.44(1) at 2 K, respectively. This is interpreted as the result of a partial charge disproportionation of the type 2Ni{sup 3+}->Ni1{sup (3-{delta})+}+Ni2{sup (3+{delta})+}, with {delta}{approx}0.55 at T=2 K. The magnetic structure has been studied from a NPD pattern at T=2 K, well below the establishment of the antiferromagnetic (AFM) ordering at T{sub N}=154 K, as well as from sequential data collected from 16 K down to 2 K. The magnetic order is defined by the propagation vector k=(1/2,0,1/2). Two possible magnetic structures are compatible with the magnetic intensities. In the second solution both Ni sublattices participate in the magnetic order, as well as Dy since it corresponds to a total disproportionation of Ni{sup 3+} to Ni{sup 2+} and Ni{sup 4+}. In the second solution both Ni sublattices participate in the magnetic order, as well as Dy. The magnetic moments for Ni1 and Ni2 atoms at T=2 K are 1.8 (2) and 0.8 (2) mu{sub B}, respectively. These values are also compatible with a partial charge disproportionation. Dy{sup 3+} ions exhibit long-range magnetic ordering below 8 K. An abrupt contraction of the unit-cell volume is observed at this temperature, due to a magnetoelastic coupling. The magnetic moment for Dy{sup 3+} at T=2 K is 7.87 (6) {mu}{sub B}. - Abstract: DyNiO{sub 3} undergoes a metal-insulator transition at T{sub MI}=564 K. Below T{sub MI} the structure is monoclinic with two different sites for the Ni atoms, which present a different valence. It is interpreted as a partial charge disproportionation. Below T{sub N}=154 K DyNiO{sub 3} orders with an antiferromagnetic structure defined by k=(1/2,0,1/2). Display Omitted

36 MATERIALS SCIENCE↗

Phase equilibria of the Ba-Sm-Y-Cu-O system for coated conductor applications

The complex phase relationships near the BaO-poor region of the quaternary Ba-Sm-Y-Cu-O oxide system prepared in pure air (p{sub O{sub 2}}=22 kPa, 950 {sup o}C) and in 0.1% O{sub 2} (p{sub O{sub 2}}=100 Pa, 810 {sup o}C) have been determined. This investigation also included the subsolidus compatibilities in ten subsystems (Ba-Sm-Y-O, Ba-Sm-Cu-O, Ba-Y-Cu-O, Sm-Y-Cu-O, Ba-Sm-O, Ba-Y-O, Ba-Cu-O, Sm-Y-O, Sm-Cu-O, and Y-Cu-O), and the homogeneity range of five solid solutions (Ba(Sm{sub x}Y{sub 2-x})CuO{sub 5}, (Sm,Y){sub 2}O{sub 3}, (Sm,Y){sub 2}CuO{sub 4}, (Y,Sm){sub 2}Cu{sub 2}O{sub 5}, and Ba(Sm,Y){sub 2}O{sub 4}). The single phase range of the superconductor solid solution, (Ba{sub 2-x}Sm{sub x})(Sm{sub 1-y}Y{sub y})Cu{sub 3}O{sub 6+z}, and the phase compatibilities in its vicinity, which are particularly important for processing, are described in detail. The phase equilibrium data of the Ba-Sm-Y-Cu-O system will enable the improvement of the intrinsic superconducting properties of second-generation wires, and facilitate the flux-pinning process. -- Graphical Abstract: Phase diagram overview of the Ba-Sm-Y-Cu-O system in the BaO-poor region prepared in p{sub O2}=22 kPa, 950 {sup o}C. Display Omitted

36 MATERIALS SCIENCE↗

Designing new n=2 Sillen–Aurivillius phases by lattice-matched substitutions in the halide and [Bi{sub 2}O{sub 2}]{sup 2+} layers

A new n=2 Sillen–Aurivillius compound Bi{sub 3}Sr{sub 2}Nb{sub 2}O{sub 11}Br has been synthesised based on Bi{sub 3}Pb{sub 2}Nb{sub 2}O{sub 11}Cl by simultaneously replacing Pb{sup 2+} with Sr{sup 2+} and Cl{sup −} with Br{sup −}. Rietveld refinements against X-ray and neutron powder diffraction data revealed a significant relative compression in the stacking axis (c-axis) of the new compound. Sr{sup 2+} doping reduces the impact of the stereochemically active 6s{sup 2} lone pair found on Pb{sup 2+} and Bi{sup 3+}, resulting in a contraction of the c-axis by 1.22% and an expansion of the ab plane by 0.25%. This improves the inter-layer compatibility with the larger halide Br{sup −}. Analysis of X-ray absorption near-edge spectroscopy data show that the ferroelectric distortion of the B-site cation is less apparent in Bi{sub 3}Sr{sub 2}Nb{sub 2}O{sub 11}Br compared to Bi{sub 3}Pb{sub 2}Nb{sub 2}O{sub 11}Cl, and variable-temperature neutron diffraction data show no evidence for a ferroelectric distortion. - Graphical abstract: The structural expansion and contractions in the stacking axis of co-doped Sillen–Aurivillius phases. Display Omitted - Highlights: • A new Sillen–Aurivillius phase Bi{sub 3}Sr{sub 2}Nb{sub 2}O{sub 11}Br is synthesised based on Bi{sub 3}Pb{sub 2}Nb{sub 2}O{sub 11}Cl. • The stacking axis contracts although local expansion accommodates the larger halide Br. • Majority of the contraction is observed in the [Bi{sub 2}O{sub 2}]{sup 2+} layers where we replaced Pb{sup 2+} for Sr{sup 2+}. • Removing the Pb{sup 2+} lowers the lone pair effect and improves inter-layer compatibility. • XANES and NPD suggest that the ferroelectric properties are minimised or suppressed.

36 MATERIALS SCIENCE↗

Synthesis and characterization of La{sub 0.6}Sr{sub 0.4}Fe{sub 0.8}Cu{sub 0.2}O{sub 3−δ} oxide as cathode for Intermediate Temperature Solid Oxide Fuel Cells

Nanocrystalline La{sub 0.6}Sr{sub 0.4}Fe{sub 0.8}Cu{sub 0.2}O{sub 3−δ} (LSFCu) material was synthetized by combustion method using EDTA as fuel/chelating agent and NH{sub 4}NO{sub 3} as combustion promoter. Structural characterization using thermodiffraction data allowed to determine a reversible phase transition at 425 °C from a low temperature R-3c phase to a high temperature Pm-3m phase and to calculate the thermal expansion coefficient (TEC) of both phases. Important characteristics for cathode application as electronic conductivity and chemical compatibility with Ce{sub 0.9}Gd{sub 0.1}O{sub 2−δ} (CGO) electrolyte were evaluated. LSFCu presented a p-type conductor behavior with maximum conductivity of 135 S cm{sup −1} at 275 °C and showed a good stability with CGO electrolyte at high temperatures. This work confirmed that as prepared LSFCu has excellent microstructural characteristics and an electrical conductivity between 100 and 60 S cm{sup −1} in the 500–700 °C range which is sufficiently high to work as intermediate temperature Solid Oxide Fuel Cells (IT-SOFCs) cathode. However a change in the thermal expansion coefficient consistent with a small oxygen loss process may affect the electrode-electrolyte interface during fabrication and operation of a SOFC. - Graphical abstract: Nanocrystalline La{sub 0.6}Sr{sub 0.4}Fe{sub 0.8}Cu{sub 0.2}O{sub 3−δ} was prepared by gel combustion and characterized by X-ray thermodiffraction and its conductivity was determined. The phase shows a reversible rhombohedral to cubic structural phase transition at 425 °C and a semiconductor to metallic phase transition at 275 °C. - Highlights: • LSFCu was prepared by gel combustion route using EDTA and NH{sub 4}NO{sub 3}. • LSFCu shows a reversible phase transition at 425 °C from R-3c to Pm-3m phase. • The sample has a maximum conductivity value of 135 S cm{sup −1} at 275 °C. • LSFCu shows a good chemical compatibility with CGO at 900 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

New series of triple molybdates AgA{sub 3}R(MoO{sub 4}){sub 5} (A=Mg, R=Cr, Fe; A=Mn, R=Al, Cr, Fe, Sc, In) with framework structures and mobile silver ion sublattices

Triple molybdates AgA{sub 3}R(MoO{sub 4}){sub 5} (A=Mg, R=Cr, Fe; A=Mn, R=Al, Cr, Fe, Sc, In) of the NaMg{sub 3}In(MoO{sub 4}){sub 5} type were synthesized and single crystals of AgMg{sub 3}R(MoO{sub 4}){sub 5} (R=Cr, Fe) were grown. In their structures, the MoO{sub 4} tetrahedra, pairs and trimers of edge-shared (Mg, R)O{sub 6} octahedra are connected by common vertices to form a 3D framework. Large framework cavities involve Ag{sup +} cations disordered on three nearby positions with CN=3+1 or 4+1. Alternating (Mg, R)O{sub 6} octahedra and MoO{sub 4} tetrahedra in the framework form quadrangular windows penetrable for Ag{sup +} at elevated temperatures. Above 653–673 K, the newly obtained molybdates demonstrate abrupt reduction of the activation energy to 0.4–0.6 eV. At 773 K, AgMg{sub 3}Al(MoO{sub 4}){sub 5} shows electric conductivity 2.5·10{sup −2} S/cm and E{sub a}=0.39 eV compatible with characteristics of the best ionic conductors of the NASICON type. - Graphical abstract: Triple molybdates AgA{sub 3}R(MoO{sub 4}){sub 5} (A=Mg, R=Cr, Fe; A=Mn, R=Al, Cr, Fe, Sc, In) of the NaMg{sub 3}In(MoO{sub 4}){sub 5} type were synthesized, AgMg{sub 3}R(MoO{sub 4}){sub 5} (R=Cr, Fe) were structurally characterized, ion-conductive properties of AgMg{sub 3}Al(MoO{sub 4}){sub 5} were measured. Display Omitted - Highlights: • Triple molybdates AgA{sub 3}R(MoO{sub 4}){sub 5} (A=Mg, R=Cr, Fe; A=Mn, R=Al, Cr, Fe, Sc, In) of the NaMg{sub 3}In(MoO{sub 4}){sub 5} type were synthesized. • Single crystals of AgMg{sub 3}R(MoO{sub 4}){sub 5} (R=Cr, Fe) were grown and their crystal structures were determined. • Disordering Ag{sup +} ions and penetrable framework structures of AgMg{sub 3}R(MoO{sub 4}){sub 5} (R=Cr, Fe) suggest 2D-character of silver-ion mobility. • Measured ion-conductive properties of AgMg{sub 3}Al(MoO{sub 4}){sub 5} are compatible with characteristics of the best ionic conductors of the NASICON type.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructures and mechanical properties of Ti-Mo alloys cold-rolled and heat treated

In this study, the microstructures and mechanical properties of Ti-10Mo and Ti-20Mo alloys (mass%) are investigated to assess the potential use in biomedical applications. The microstructures are examined by X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM). The mechanical properties are determined from uniaxial tensile tests. The experimental results indicate that the microstructures and mechanical properties of Ti-Mo alloys are dependent upon the cold rolling, solution heat treatment, and Mo content. The Ti-10Mo alloy exhibits ({alpha}'' + {beta}) and ({beta} + {omega}) phases under the cold rolling (CR) and solution treatment (ST), respectively. By contrast, the Ti-20Mo alloy comprises only {beta} phase under such conditions. The quenched Ti-20Mo alloy has the lowest elastic modulus and CR Ti-20Mo alloy has the highest tensile strength. The quenched Ti-10Mo alloy exhibits the excellent ductility and two-stage yielding from stress-strain curves due to the stress-induced martensite transformation from {beta} to {alpha}'' during tensile deformation. These Ti-Mo alloys exhibit low yield strength and good ductility, and they are more suitable for biomedical applications than the conventional metallic biomaterials from the viewpoint of better mechanical compatibility. The quenched Ti-10Mo alloy has some advantages over the other {beta} binary Ti-Mo alloys for biomedical applications. {beta} type Ti-Mo-Sn alloys are expected to be promising candidates for novel metallic biomaterials. - Highlights: {yields} The microstructures and mechanical properties of Ti-Mo alloys are dependent upon the cold rolling, solution heat treatment, and Mo content. {yields} The quenched Ti-10Mo alloy exhibits the excellent ductility and two-stage yielding due to stress-induced martensite transformation from beta to alpha double prime during tensile deformation. {yields} The Ti-Mo alloys are more suitable for biomedical applications than the conventional metallic biomaterials from the viewpoint of better mechanical compatibility. {yields} The quenched Ti-10Mo alloy has more advantages over the other beta binary Ti-Mo alloys for biomedical applications.

36 MATERIALS SCIENCE↗

New compositional data on ancient mortars and plasters from Pompeii (Campania – Southern Italy): Archaeometric results and considerations about their time evolution

Highlights: • Mortar samples from Pompeii, with different constructive functions, were studied. • Characterization of the materials can be used for preparing compatible mortars. • Analogies and differences were highlighted to identify the constructive phases. • Preliminary statistic models were proposed to discriminate materials and constructive phases. Twenty-six samples of mortar used for various construction applications (joint mortars, floor mortars, filling mortars and plasters) were collected from different areas of the archaeological site of Pompeii (Campania - Sothern Italy). The mortar samples belong to various historical periods covering approximately 2000 years, from the 2nd century BC to the post excavation period (18–19th century). The samples were characterized employing Optical Microscopy (OM), X-ray Powder Diffraction (XRPD), X-ray Fluorescence (XRF), Electron Probe Micro Analysis (EPMA) and Raman Spectroscopy. Moreover, image analysis was carried out using JMicroVision software in order to determine the percentages of binder, macropores and aggregate, in terms of crushed ceramic fragments (cocciopesto), rock fragments and monocrystals. The application of these techniques allowed obtaining a complete chemical and minero-petrographic characterization of the samples, which may prove useful for preparing compatible repair mortars for future restoration works. The archaeometric study provided new data on the production technology of the mortars and the analogies and differences observed among the samples, enabled us to distinguish different constructive phases, thus confirming or rebutting the archaeological hypothesis on the dating of some samples. By combining compositional variables through the discriminant analysis, it was also possible to analyse the time evolution of the materials and to construct preliminary multivariate statistical models, helpful to identify the various typologies of mortars used in the different historical periods.

36 MATERIALS SCIENCE↗