Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BACKSCATTER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Seven years of aerosol scattering hygroscopic growth measurements from SGP: Factors influencing water uptake: Aerosol Scattering Hygroscopic Growth

Long-term measurements of changes in the aerosol scattering coefficient hygroscopic growth at the U.S. Department of Energy Southern Great Plains site provide information on the seasonal as well as size and chemical dependence of aerosol hygroscopic growth. Annual average sub 10 um fRH values (the ratio of aerosol scattering at 85%/40% RH) were 1.75 and 1.87 for the gamma and kappa fit algorithms, respectively. The study found higher growth rates in the winter and spring seasons that correlated with high aerosol nitrate mass fraction. FRH, exhibited strong, but differing correlations with the scattering Ångström exponent and backscatter fraction, two optical size-dependent parameters. The aerosol organic fraction had a strong influence, with fRH decreasing with increases in the organic mass fraction and absorption Ångström exponent and increasing with the aerosol single scatter albedo. Uncertainty analysis if the fit algorithms revealed high uncertainty at low scattering coefficients and slight increases in uncertainty at high RH and fit parameters values.

Jefferson, A.↗

Raman study of amorphization in nanocrystalline 3C-SiC irradiated with C+ and He+ ions

This study examines C+ and He+ ion irradiation induced amorphization processes in 3C-SiC nanograins embedded in an amorphous SiC matrix. Raman spectroscopy and Rutherford backscattering spectrometry are used for damage characterization. SiC grains with an average size of either ~6 or ~20 nm were observed to be fully amorphized to a lower dose at room temperature compared to their monocrystalline counterpart under the identical irradiation condition. In addition to damage accumulation induced amorphization in the grains, preferential amorphization at the crystalline/amorphous interfaces could play a significant role. This interface-driven amorphization proceeds at comparable rates for C+ and He+ ion irradiations. The results may have an important implication for nanocrystalline SiC to be applied in advanced nuclear reactors.

Amorphization, Ion irradiation, Silicon carbide, N↗

Relating Texture and Thermomechanical Processing Variables in Mg–Zn–Ca Alloys

It is well known that the strong basal texture commonly produced in magnesium alloy sheets leads to poor formability at room temperature. A sizable body of work has explored how changing the alloy composition and rolling conditions can yield more desirable textures; however important thermomechanical variables, such as the feed rate during rolling, are often not included in the literature, making it difficult to correlate how changes in processing affect the final crystallographic texture. This work explores the texture evolution and grain refinement in Mg-Zn-Ca alloys during plane strain compression (PSC) using a Gleeble thermomechanical simulator. This instrument allows for precise control and capture of the thermomechanical history of the sample. The texture and grain morphology of the compressed samples were characterized using Electron Backscatter Diffraction (EBSD). The texture results will be used to identify which alloys and processing conditions should be scaled up for future rolling studies.

36 MATERIALS SCIENCE↗

Experimental characterization and crystal plasticity modeling of heterogeneous deformation in polycrystalline {alpha}-Ti.

Grain-level heterogeneous deformation was studied in a polycrystalline {alpha}-Ti specimen deformed by four-point bending. Dislocation slip activity in the microstructure was investigated by surface slip trace analysis. Three-dimensional-X-ray diffraction (3D-XRD) was used to investigate subsurface lattice rotations and to identify geometrically necessary dislocations (GNDs). The slip systems of local GNDs were analyzed by studying the streaking directions of reflections in corresponding Laue patterns. The analysis performed in one grain indicated that the subsurface GNDs were from the same slip system identified using slip trace analysis in backscattered electron images. A crystal plasticity finite element (CPFE) model was used to simulate deformation of the same microstructural region. The predictions of dislocation slip activity match the general aspects of the experimental observations, including the ability to simulate the activation of different slip systems in grains where multiple slip systems were activated. Prediction of local crystal rotations, however, was the least accurate aspect of the CPFE model.

36 MATERIALS SCIENCE↗

Microstructure and In Situ Observations of Undercooling for Nucleation of [beta]-Sn Relevant to Lead-Free Solder Alloys

Difficult nucleation of {beta}-Sn during solidification of tin and tin-based lead-free solder alloys can result in high degrees of undercooling of the liquid prior to solidification. The undercooling can produce solder joints with large grains, anisotropic behavior, and undesirable mechanical properties. This paper describes our examination of the amount of undercooling of tin on both graphite (non-wetting) and copper (wetting) surfaces using in situ x-ray diffraction. The microstructure was further characterized by optical microscopy, scanning electron microscopy, and electron backscattering diffraction imaging microscopy. Undercoolings as high as 61 C were observed for Sn solidified on graphite, while lower undercoolings, up to 30 C, were observed for Sn solidified on copper. The microstructure of the high purity Sn sample solidified on graphite showed very few grains in the cross-section, while the commercially pure Sn sample solidified with only one grain and was twinned. Tin solidified on copper contained significant amounts of copper in the tin, intermetallic phase formation at the interface, and a eutectic microstructure.

36 MATERIALS SCIENCE↗

Importance of Martensite Spatial Distribution at Large Volume Fractions in Imparting Ductility in High-Strength Dual-Phase Steel

Controlled austenite decomposition in a cold-rolled steel was carried out in a hot-dip process simulator with different inter-critical annealing process parameters to produce dual-phase steel consisting of martensite phase fraction above 50%. The evolving microstructure was characterized by using scanning electron microscope and electron backscattered diffraction techniques. Macro- and micro-texture was characterized by using x-ray diffraction and electron backscattered diffraction techniques, respectively. Uniaxial tensile deformation showed a very good combination of ultra-high strength above 900 MPa with uniform elongation of above 7%. An anomalous increase in ductility was observed for steel with high martensite volume fraction of 62.2% compared to that of lower fraction of 52.3%, indicating the influence of size and spatial distribution arrangement of ferrite and martensite phases. The enhancement in the ductility with high strength was attributed to the improved plastic deformability of hard fine martensite phase along with fine ferrite surrounding it. The nature of micro- and macro-texture was also found to affect strain partitioning compatibility between ferrite and martensite in this study.

36 MATERIALS SCIENCE↗

Damage evolution of ion irradiated defected-fluorite La 2 Zr 2 O 7 epitaxial thin films

Pyrochlore-structure oxides, A2B2O7, may exhibit remarkable radiation tolerance due to the ease with which they can accommodate disorder by transitioning to a defected fluorite structure. The mechanism of defect formation was explored by evaluating the radiation damage behavior of high quality epitaxial La2Zr2O7 thin films with the defected fluorite structure, irradiated with 1 MeV Zr+ at doses up to 10 displacements per atom (dpa). The level of film damage was evaluated as a function of dose by Rutherford backscattering spectrometry in the channeling geometry (RBS/c) and scanning transmission electron microscopy (STEM). At lower doses, the surface of the La2Zr2O7 film amorphized, and the amorphous fraction as a function of dose fit well to a stimulated amorphization model. As the dose increased, the surface amorphization slowed, and amorphization appeared at the interface. Even at a dose of 10 dpa, the core of the film remained crystalline, despite the prediction of amorphization from the model. To inform future ab initio simulations of La2Zr2O7, the bandgap of a thick La2Zr2O7 film was measured to be indirect at 4.96 eV, with a direct transition at 5.60 eV.

Environmental Molecular Sciences Laboratory↗

Effect of stress on Laves phase precipitation in creep ruptured Grade 92 ferritic martensitic steel characterized by a novel accessible method

At high temperature conditions relevant to fossil and nuclear energy plants, Laves phase (Fe 2 X, X=Mo, W) precipitation is observed in common ferritic martensitic (FM) structural steels, with various reported effects on creep behavior. Despite being valuable metrics to correlate with mechanical properties and other precipitate phases, the volume fraction and number density of Laves phase precipitates has been difficult to quantify accurately using common techniques such as transmission electron microscopy (TEM) due to the relatively large size (∼0.25 μm) and low number density (∼10 11 cm −3 ) of Laves precipitates. Here, to address this characterization challenge, we developed and demonstrated a high-throughput and widely accessible method to quantify the volume fraction and number density of the Laves phase based on scanning electron microscope (SEM) images with a backscattered electron signal and the information depth (ID) of backscattered electrons. We applied this new technique in creep ruptured Grade 92 FM steel to study the effect of Laves phase on creep properties and determine the influence of stress on Laves phase precipitation. The quantitative accuracy of the SEM-based volume fraction and number density values was verified using synchrotron high energy X-ray diffraction and serial sectioning tomography. Stress did not significantly affect the Laves phase size or volume fraction during creep testing at 550 – 650°C and stress levels of 90 – 260 MPa (vs. unstressed conditions). Conversely, a moderate but statistically significant stress-enhanced increase in Laves phase number density, corresponding to an increase in nucleation rate, occurred during creep exposure above 110 MPa.

Creep↗

The causal relationship between melt pool geometry and energy absorption measured in real time during laser-based manufacturing

During laser powder bed fusion additive manufacturing, laser power absorption is governed by a pro -tean pool of molten metal that can present as a highly reflective surface, a deeply absorbing cavity, or some amalgamation thereof. These melt pool dynamics have been linked to defect creation, porosity, and surface finish quality. Although these are therefore critical for determining final part quality, their in-stantaneous influence on laser absorption have only been explored through simulation. To date, direct real-time observations have been elusive due to the locally extreme environment. In this work, we fo-cus a laser on Ti-6Al-4V powder and bare plate while quantifying the time-dependent, absolute energy absorption by monitoring omnidirectional backscattered laser intensity. We also simultaneously record the projective melt pool geometries with high-speed synchrotron x-ray imaging. We find that laser ab-sorption strongly reflects the stability of the vapor depression over a wide range of applied laser powers, oxygen content in the processing atmosphere, and with the presence of powder. During laser scanning of a powder bed surface, we find a significant absorption reduction after 400 mu s due to a dramatic change in the vapor depression aspect ratio-an event known to create porosity. Furthermore, as several industrial scan strate-gies necessitate thousands of these events during a build, their identification and control is of significant practical importance. Lastly, a normalized enthalpy model is demonstrated to be effective in quantifying the relationship between the laser absorption and cavity depth, even under transient conditions. In addi-tion to providing vital quantitative data for simulation calibration, the correlation of melt pool geometry with laser absorption during realistic processing conditions suggests the use of a total backscattered light detection system for real-time process control.

36 MATERIALS SCIENCE↗

Sea spray aerosol production flux retrieval based on Doppler lidar measurements

Supermicron sea spray aerosols (SSA) play a crucial role in stratocumulus cloud microphysics and drizzle formation. However, our understanding of SSA's spatiotemporal distribution, production mechanisms, and fluxes in the marine boundary layer remains limited. This study introduces a novel approach to determine supermicron SSA production flux and number concentration at various heights above the ocean surface. Our method leverages Doppler lidar data, specifically attenuated backscatter and vertical velocity, collected at a 105 m range gate during the Eastern Pacific Clouds and Aerosols for Precipitation Experiment (EPCAPE) at Scripps Pier, La Jolla, California. To focus on nascent SSA, we analyzed data from periods with wind directions between 225° and 315° and wind speeds exceeding 4 m s −1 . Cloud and precipitation events were excluded using relative humidity, backscatter thresholds, and 2D Video Disdrometer observations. Results show that calculated supermicron SSA number concentrations at 105 m ranged from 0.26 to 2.93 cm −3 for surface wind speeds between 4 and 6 ms −1 . When exceeding the method's Limit of Detection, estimated production fluxes ranged from 0.20 to 1.53 cm −2 s −1 . This methodology has potential for application in various oceanic locations, likely enhancing our understanding of SSA's role in atmospheric processes and climate interactions.

54 ENVIRONMENTAL SCIENCES↗

In Vivo Dosimetry for Single-Fraction Targeted Intraoperative Radiotherapy (TARGIT) for Breast Cancer

Purpose: In vivo dosimetry provides an independent check of delivered dose and gives confidence in the introduction or consistency of radiotherapy techniques. Single-fraction intraoperative radiotherapy of the breast can be performed with the Intrabeam compact, mobile 50 kV x-ray source (Carl Zeiss Surgical, Oberkochen, Germany). Thermoluminescent dosimeters (TLDs) can be used to estimate skin doses during these treatments. Methods and Materials: Measurements of skin doses were taken using TLDs for 72 patients over 3 years of clinical treatments. Phantom studies were also undertaken to assess the uncertainties resulting from changes in beam quality and backscatter conditions in vivo. Results: The mean measured skin dose was 2.9 {+-} 1.6 Gy, with 11% of readings higher than the prescription dose of 6 Gy, but none of these patients showed increased complications. Uncertainties due to beam hardening and backscatter reduction were small compared with overall accuracy. Conclusions: TLDs are a useful and effective method to measure in vivo skin doses in intraoperative radiotherapy and are recommended for the initial validation or any modification to the delivery of this technique. They are also an effective tool to show consistent and safe delivery on a more frequent basis or to determine doses to other critical structures as required.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

On the onset of deformation twinning in the CrFeMnCoNi high-entropy alloy using a novel tensile specimen geometry

Deformation-induced nanoscale twinning is one of the mechanisms responsible for the excellent combination of strength and fracture toughness of the single-phase, face-centered cubic CrMnFeCoNi (Cantor) alloy, especially at cryogenic temperatures. In this work, we use a novel, modified dogbone geometry that allows the sampling of varying stress and strain regions within a single tensile specimen to characterize the onset of twinning in CrMnFeCoNi at 293 K, 198 K and 77 K. Electron backscatter diffraction (EBSD) and backscattered electron (BSE) imaging revealed the presence of deformation nano-twins in regions of the samples that had experienced plastic strains of ~25% at 293 K, ~16% at 198 K, and ~8% at 77 K, which are similar to the threshold strains described by Laplanche et al. ( Acta Mater. 118, 2016, 152–163). From these strains we estimate that the critical tensile stress for the onset of twinning in this alloy is on the order of 750 MPa.

36 MATERIALS SCIENCE↗

Relationships among diurnal variations of polar night cloud, precipitation, surface temperatures, and the fair-weather return current of the global electric circuit (GEC)

Over the past five years (June 2017-current), the vertical electric field (E z ) as well as numerous cloud, precipitation and radiation properties have been monitored at the Department of Energy-Atmospheric Radiation Measurement (DOE ARM) North Slope of Alaska (NSA) field site. Comparisons between the composite diurnal averaged fair-weather E z , and composite ceilometer derived cloud base height during the polar night, reveal a significant correlation between the parameters (r = 0.62), supporting previous studies that there is high correlation between local electric field and cloud properties. With the use of extensive instrumentation at the site, such as the Micro Pulse Lidar (MPL), Ka-band Zenith Radar (KAZR), ceilometer, SKYRAD, Precipitation Imaging Package (PIP), among others, this study provides a more comprehensive examination of the diurnal cycle of cloud and precipitation properties along with the localized fair-weather return current of the larger Global Electric Circuit (GEC) system. Comparisons between the composite diurnal averaged fair-weather E z , and cloud thickness, maximum column backscatter, and precipitation particle counts all show similar diurnal variability during the polar night, indicating that during the largest magnitude fair weather E z time periods, clouds bases tend to be higher, clouds are thicker, have a larger column backscatter, and display more precipitating particles. Furthermore, a slight diurnal variability in the polar night surface temperature was found to be highly correlated (r = 0.87) to the longwave downwelling irradiance measured by SKYRAD, indicating that the variations in the physical properties of local clouds could modulate the diurnal polar night surface temperature variability on the order of 0.5 °C/day. In conclusion, these findings emphasize the importance and global nature of the GEC system, with the global aggregate of thunderstorms and electrified clouds potentially influencing polar night cloud properties as well as diurnal wintertime polar surface temperature variation.

54 ENVIRONMENTAL SCIENCES↗

Processing effects on microstructure in Er and ErD 2 thin-films

Erbium metal thin-films have been deposited on molybdenum-on-silicon substrates and then converted to erbium dideuteride (ErD 2 ). Here in this work, we study the effects of deposition temperature (≈300 or 723 K) and deposition rate (1 or 20 nm/s) upon the initial Er metal microstructure and subsequent ErD 2 microstructure. We find that low deposition temperature and low deposition rate lead to small Er metal grain sizes, and high deposition temperature and deposition rate led to larger Er metal grain sizes, consistent with published models of metal thin-film growth. ErD 2 grain sizes are strongly influenced by the prior-metal grain size, with small metal grains leading to large ErD 2 grains. A novel sample preparation technique for electron backscatter diffraction of air-sensitive ErD 2 was developed, and allowed the quantitative measurement of ErD 2 grain size and crystallographic texture. Finer-grained ErD 2 showed a strong (1 1 1) fiber texture, whereas larger grained ErD 2 had only weak texture. Finally, we hypothesize that this inverse correlation may arise from improved hydrogen diffusion kinetics in the more defective fine-grained metal structure or due to improved nucleation in the textured large-grain Er.

36 MATERIALS SCIENCE↗

Channeling analysis in studying ion irradiation damage in materials containing various types of defects

We present that ion channeling is a powerful quantitative technique for studying ion-irradiation induced defect evolution in single crystalline materials. An iterative procedure to determine dechanneling yields has been developed for decades, serving as a major method for analyzing experimental channeling data. The applicability of such procedure is, however, generally limited to the crystalline damage with only point defects and local amorphous domains. For the other cases, such as irradiated metals, the assumption of direct-backscattering free has usually been made. In the present study, Ni, TiAl, MgO, and SrTiO 3 single crystals are selected as four model materials, representing metals, intermetallic alloys, and ceramic compounds with different defect evolution processes under irradiation, to investigate the fidelity of applying dechanneling analysis on various types of defects. The pure dechanneling assumption is shown oversimplified in Ni irradiated with low fluence self-ions and may result in error on the derived damage profile. Moreover, the iterative procedure of dechanneling analysis is shown valid for more general situations than the randomly distributed atoms, including those not exhibiting a peak in channeling spectra. The disappearance of damage peak in channeling spectra is attributed to the combined effects of small (but non-zero) scattering factor, long-range damage effects, and non-ignorable damage level in pristine crystals. Furthermore, the ratio of direct backscattering to dechanneling areas provides information on defect configurations in the materials containing a well-defined damage peak in channeling spectra. Finally, the contribution from dechanneling sources increases from SrTiO 3 , TiAl, to MgO, according to the derived scattering and dechanneling factors.

36 MATERIALS SCIENCE↗