SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Approximate spectral analysis faster and less expensive than transient analysis. Method of vibration analysis combines separate modes of spacecraft and launcher to determine approximate conditions for resonance. Useful for analysis of any complex structure made up of substructures not coupled too closely; however important to note, method includes effect of dynamic impedance between launcher and payload.
Computational efficiency in structural optimization can be enhanced if the intensive computations associated with the calculation of the sensitivities, that is, gradients of the behavior constraints, are reduced. Approximation to gradients of the behavior constraints that can be generated with small amount of numerical calculations is proposed. Structural optimization with these approximate sensitivities produced correct optimum solution. Approximate gradients performed well for different nonlinear programming methods, such as the sequence of unconstrained minimization technique, method of feasible directions, sequence of quadratic programming, and sequence of linear programming. Structural optimization with approximate gradients can reduce by one third the CPU time that would otherwise be required to solve the problem with explicit closed-form gradients. The proposed gradient approximation shows potential to reduce intensive computation that has been associated with traditional structural optimization.
Suitably formulated spatial modulation of a scene imaged by a computed-tomography imaging spectrometer (CTIS) has been found to be useful as a means of improving the imaging performance of the CTIS. As used here, "spatial modulation" signifies the imposition of additional, artificial structure on a scene from within the CTIS optics. The basic principles of a CTIS were described in "Improvements in Computed- Tomography Imaging Spectrometry" (NPO-20561) NASA Tech Briefs, Vol. 24, No. 12 (December 2000), page 38 and "All-Reflective Computed-Tomography Imaging Spectrometers" (NPO-20836), NASA Tech Briefs, Vol. 26, No. 11 (November 2002), page 7a. To recapitulate: A CTIS offers capabilities for imaging a scene with spatial, spectral, and temporal resolution. The spectral disperser in a CTIS is a two-dimensional diffraction grating. It is positioned between two relay lenses (or on one of two relay mirrors) in a video imaging system. If the disperser were removed, the system would produce ordinary images of the scene in its field of view. In the presence of the grating, the image on the focal plane of the system contains both spectral and spatial information because the multiple diffraction orders of the grating give rise to multiple, spectrally dispersed images of the scene. By use of algorithms adapted from computed tomography, the image on the focal plane can be processed into an image cube a three-dimensional collection of data on the image intensity as a function of the two spatial dimensions (x and y) in the scene and of wavelength (lambda). Thus, both spectrally and spatially resolved information on the scene at a given instant of time can be obtained, without scanning, from a single snapshot; this is what makes the CTIS such a potentially powerful tool for spatially, spectrally, and temporally resolved imaging. A CTIS performs poorly in imaging some types of scenes in particular, scenes that contain little spatial or spectral variation. The computed spectra of such scenes tend to approximate correct values to within acceptably small errors near the edges of the field of view but to be poor approximations away from the edges. The additional structure imposed on a scene according to the present method enables the CTIS algorithms to reconstruct acceptable approximations of the spectral data throughout the scene.
The NMC method has proven utility for prescribing approximate background-error covariances required by variational data assimilation systems. Here, untunedNMCmethod estimates are compared with explicitly determined error covariances produced within an OSSE context by exploiting availability of the true simulated states. Such a comparison provides insights into what kind of rescaling is required to render the NMC method estimates usable. It is shown that rescaling of variances and directional correlation lengths depends greatly on both pressure and latitude. In particular, some scaling coefficients appropriate in the Tropics are the reciprocal of those in the Extratropics. Also, the degree of dynamic balance is grossly overestimated by the NMC method. These results agree with previous examinations of the NMC method which used ensembles as an alternative for estimating background-error statistics.
The behavior of vortex flow at high swirls is investigated. The problem was first formulated in the method of weighted residuals, using Bessel functions as approximating functions. Convergent solutions require a large number of steps in the axial direction and do not seem to offer an advantage over traditional methods. As the results do not differ substantially from those of the zeroth approximation (the solution for 'cylindrical' flow), this approximation is then explored and discussed in more detail. It is used to derive a relationship predicting a critical radius for which stagnation on the axis (vortex breakdown) can be expected for a given swirl. Flow patterns with open and closed vortex bubbles are explored. At high swirls, even minute variations in outer streamtube radius have profound effects on the flow. Vortex breakdown bubbles in divergences, tubes, and free flows can be explained.
A method for generating finite-dimensional approximations to the solutions of optimal control problems is introduced. By employing a description of the dynamical system in terms of its attainable sets in favor of using differential equations, the controls are completely eliminated from the system model. Besides reducing the dimensionality of the discretized problem compared to state-of-the-art collocation methods, this approach also alleviates the search for initial guesses from where standard gradient search methods are able to converge. The mechanics of the new method are illustrated on a simple double integrator problem. The performance of the new algorithm is demonstrated on a 1-D rocket ascent problem ('Goddard Problem') in presence of a dynamic pressure constraint.
A method for generating finite-dimensional approximations to the solutions of optimal control problems is introduced. By employing a description of the dynamical system in terms of its attainable sets in favor of using differential equations, the controls are completely eliminated from the system model. Besides reducing the dimensionality of the discretized problem compared to state-of-the-art collocation methods, this approach also alleviates the search for initial guesses from where standard gradient search methods are able to converge. The mechanics of the new method are illustrated on a simple double integrator problem. The performance of the new algorithm is demonstrated on a I-D rocket ascent problem ('Goddard Problem') in presence of a dynamic pressure constraint.
A method for generating finite-dimensional approximations to the solutions of optimal control problems is introduced. By employing a description of the dynamical system in terms of its attainable sets in favor of using differential equations, the controls are completely eliminated from the system model. Besides reducing the dimensionality of the discretized problem compared to state-of-the-art collocation methods, this approach also alleviates the search for initial guesses from where standard gradient search methods are able to converge. The mechanics of the new method are illustrated on a simple double integrator problem. The performance of the new algorithm is demonstrated on a 1-D rocket ascent problem (`Goddard Problem') in presence of a dynamic pressure constraint.
The paper presents an unsteady aerodynamic influence coefficient method based on the low-frequency approximation. The influence coefficients are of a type which have been used to compute steady flow about wing-body combinations; therefore, the new method may be extended readily to low-frequency unsteady flow about wing-body combinations. The validity of the method is demonstrated by comparisons with numerical results from conventional, unsteady lifting surface methods. The method is valid for arbitrary wings in supersonic flow and for wings of finite span in subsonic flow. The method, when extended to include wing-body-tail interactions, will have important applications for predicting stability, control, and gust response characteristics of large airplanes. Dynamic stability derivatives and pressure distributions are given for several planforms. The comparison with either analytical or other well established numerical methods shows good agreement.-
A method for calculating the radiation pattern of end-fire tapered slot antennas with or without dielectric substrate is presented. The method involves a two-step procedure: (1) determine the field distribution of a traveling wave along the tapered slot, and (2) compute the radiation from this slot field by using the half-plane Green's function to account for termination effects. Acceptable estimates of the slot field usually can be obtained from a stepped approximation to the tapered geometry. The method has been verified by comparisons to measured patterns for various dielectric substrates and antenna dimensions. However, the effect of lateral truncation has not yet been successfully modeled. Experimental patterns showing this effect are presented.
Numerical solution of two dimensional, time dependent, compressible viscous Navier-Stokes equations about arbitrary bodies was treated using density gradients as additional dependent variables. Thus, six dependent variables were computed with the SOR iteration method. Besides formulation for pressure gradient terms, a formulation for computing the body density was presented. To approximate the governing equations, an implicit finite difference method was employed. In computing the solution for the flow about a circular cylinder, a problem arose near the wall at both stagnation points. Thus, computations with various conditions were tried to examine the problem. Also, computations with and without formulations are compared. The flow variables were computed on 37 by 40 field first, then on an 81 by 40 field.
In this work, several neural network function approximations are compared for inter- polating, storing, and sampling acoustic source spheres with applications to propeller noise estimation. These methods are compared using an acoustic model of the three bladed GL-10 propeller at different flight conditions, with training data generated using NASA’s ANOPP-PAS module. The source spheres used to train the networks capture the tonal propeller noise due to both the blade thickness and loading. This tonal noise prediction method allows the vehicle noise to be estimated for auralization and acoustic control. Three radial basis function neural network architectures are compared in this work. The first two networks directly estimate the parameters of the source sphere at different flight conditions but differ in the number of layers used. The third network estimates the parameters of the source sphere using a weighted combination of spherical basis functions. These networks are trained on numerically generated source spheres, with operating points given in terms of the propeller rotation rate, freestream speed, and propeller angle of attack. The performance of the neural network is determined using a validation dataset of withheld data points. This performance is quantified in terms of the approximation error, training time, and sample time. The third network, which estimates the weights of the spherical basis functions, performs the best in both average and maximum approximation errors in all cases. This network’s worst case performance is 5.6 % relative dif- ference of a model parameter associated with acoustic pressure. The direct estimation network with a single layer has the worst approximation error in all cases. Additionally, the spherically defined network has the slowest sample time at 0.05 seconds per thousand points. Both direct estimation methods produce a thousand sample points in approximately 0.001 seconds.
The modified structure method, which is based on Koiter's theory of imperfections, was used to calculate approximate buckling loads of several shells of revolution. The method does not appear to be practical for shells because, in many cases, the prebuckling nonlinearity may be too large to be treated accurately as a small imperfection.
Many future NASA programs require very high accurate pointing stability. These pointing requirements are well beyond anything attempted to date. This paper suggests a control system which has the capability of meeting these requirements. An optimal control law for the suggested system is specified. However, since no direct method of solution is known for this complicated system, a computation technique using successive approximations is used to develop the required solution. The method of calculus of variations is applied for estimating the changes of index of performance as well as those constraints of inequality of state variables and terminal conditions. Thus, an algorithm is obtained by the steepest descent method and/or conjugate gradient method. Numerical examples are given to show the optimal controls.
Computational structures technology (CST), which has emerged from FEM developments, is a fusion of materials modeling, structural and dynamic analysis and synthesis methods, on the one hand, and numerical analysis and approximation theory, on the other. In addition to computational materials modeling, CST encompasses computational methods for predicting the response, performance, failure, and service life of structures and their components, as well as automated methods for structural synthesis and optimization.
A method to evaluate the performance of fault tolerant systems whose configuration can be represented by time-invariant, discrete-time, discrete-state Markov models is introduced. Each state is assumed to be associated with a constant qualitative measure of the system's performance. The method first computes the moments of the performance probability mass function (PMF) and then finds an approximating function that has the same moments. The form of this function is a maximum entropy solution of the moment matching problem. A simple algorithm for calculating the necessary moments is derived and a method for finding the approximate performance PMF is suggested. After some modification, the method is applied to an example, the Inertial Upper Stage navigation system.
A method based on the use of constrained spline fits is used to overcome the difficulties arising when body-wave data in the form of T-delta are reduced to the tau-p form in the presence of cusps. In comparison with unconstrained spline fits, the method proposed here tends to produce much smoother models which lie approximately in the middle of the bounds produced by the extremal method. The method is noniterative and, therefore, computationally efficient. The method is applied to the lunar seismic data, where at least one triplication is presumed to occur in the P-wave travel-time curve. It is shown, however, that because of an insufficient number of data points for events close to the antipode of the center of the lunar network, the present analysis is not accurate enough to resolve the problem of a possible lunar core.
The Schwarz-Neumann alternating method is employed to obtain stress intensity solutions to two crack problems of practical importance: a semi-infinite elastic plate containing an edge crack which is subjected to concentrated normal and tangential forces, and an elastic half space containing a semicircular surface crack which is subjected to uniform opening pressure. The solution to the semicircular surface crack is seen to be a significant improvement over existing approximate solutions. Application of the alternating method to other crack problems of current interest is briefly discussed.