Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “tables”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

IMS/Satellite Situation Center report: Predicted orbit plots for IMP-J-1976

Predicted orbit plots for the IMP-J satellite were given for the time period January-December 1976. These plots are shown in three projections. The time period covered by each set of projections is 12 days and 6 hours, corresponding approximately to the period of IMP-J. The three coordinate systems used are the Geocentric Solar Ecliptic system (GSE), the Geocentric Solar Magnetospheric system (GSM), and the Solar Magnetic system (SM). For each of the three projections, time ticks and codes are given on the satellite trajectories. The codes are interpreted in the table at the base of each plot. Time is given in the table as year/day/decimal hour, and the total time covered by each plot is shown at the bottom of each table.

Source record↗

Multi-asteroid flyby trajectories using Venus-earth gravity assists

The feasibility of using Venus and earth gravity assists for delivering spacecraft to the asteroid belt with a low launch energy but with the additional flight time from earth to Venus and back to earth. A numerical investigation for this kind of trajectory reveals a wide range of possibilities. Energy gain tables and synodic and resonance interval tables are presented for the gravity-assist trajectories. Tables are presented for the first twenty asteroids on the trajectories. These gravity-assist flybys are compared to direct launch multi-asteroid flybys, illustrating the advantage of the gravity-assist type in launch energy requirements.

Bender, D. F.↗

Summary of studies for a solar optical telescope in space: 1968-1976

The primary objective of this review is to tabulate the basic recommendations of several solar telescope studies. A primary matrix, listing some of the basic optical parameters, was compiled and forms the basis for a table. From this table it is apparent that a strong consensus exists on the configuration of the telescope and on its fundamental dimensionless parameters. Other tables presented in this document address the basic approach of each study to the telescope design as well as to the design of critical subsystems. These subsystem problems include the material, coating, configuration, mounting, launch locks, and thermal control of the primary mirror, the structure of the main telescope and the instrument bay, the mechanisms for radiation rejection, thermal control, and meteoroid shielding, and methods of maintaining image quality by proper alignment and by image motion compensation.

Bremer, J.↗

Rotary leveling base platform

A leveling apparatus for the precise adjustment of a scientific instrument is reported. A base member is provided having a hollow cylindrical shape. A table for supporting the instrument rests on the base and has a shaft portion extending below the table. The upper portion of the shaft fits tightly into the hollow portion of the base member whereas the lower portion of the shaft is machined to fit loosely. The lower portion of the shaft is provided with a groove. Adjusting screws are threaded through the hollow cylindrical portion and are adapted to enter the groove. By adjusting the screws, the lower portion of the shaft is moved in a vertical plane since the shaft is loosely fitted into the cylinder. The upper portion of the shaft which is tightly fitted into the upper end of the cylinder causes the cylinder to deform slightly providing a fulcrum point which allows the table to be leveled in response to the adjustment of the adjusting screws.

Delaplaine, R. W.↗

Jig for assembling large composite panels

Layup of composite panels as large as 15 by 60 ft is greatly facilitated by simple mechanism. Jig consists of flat, detachable table, and curved laminating-plate joined by rack and pinion to insure accurate registration. Vacuum holds thin plastic film to laminating-plate. Preimpregnated composite sheet is applied to plate, which is then lowered face down onto table. Release of vacuum leaves layer and film and table. Film is peeled off, and steps are repeated for next layer of laminate.

Watts, J. T.↗

Asteroid rotation. IV

The results from the year 1979 of an ongoing program of asteroid photometry at Table Mountain Observatory are presented. The results for 53 asteroids are summarized in a table, showing the number, name, opposition date, taxonomic class, diameter, absolute magnitude, mean absolute magnitude at zero phase angle and values of the absolute magnitude and linear phase coefficient derived from it, the rotation period in hours, peak-to-peak amplitude of variation, difference between mean and maximum brightness, and reliability index. Another table presents data on aspect and comparison stars, including brightness and distance data. Reliable rotation periods are reported for 22 asteroids for which no previous values are known. For seven asteroids, periods are reported which are revisions of previously reported values.

Harris, A. W.↗

JPL pulsar timing observations. II - Geocentric arrival times

Monitoring of the behavior of naturally pulsating galactic radio sources, or pulsars, through regularly spaced measurements of pulse arrival times, has been conducted by several laboratories. A tabular presentation is here made of pulse arrival time measurements from the NASA Deep Space Network between late 1968 and early 1981. By expressing the measurements in ephemeris time, and referring them to the geocenter, usable tables of results have been generated for each pulsar listed in the first of the tables given. The considerations addressed by the tables are: (1) a necessary step in the study of pulsar dynamics is the reduction of topocentric arrival times to the barycenter of the solar system; (2) the tabulated data are accessible to all opinions as to the procedures to be used in interpreting arrival time data; and (3) different observing programs can usually be combined to produce an improvement in the total data set.

Downs, G. S.↗

Heterodyne frequency measurements and frequency calibration standards for tunable diode lasers

New frequency calibration tables are required to keep abreast of the resolution attainable by currently available tunable lasers. One key to the generation of tables with requisite accuracy involves accurate heterodyne frequency measurements; another key consists of reliable fitting and analysis. Coordinated activity in NBS involves selection of suitable molecular calibration candidates, their frequency measurement and analysis, and dissemination of the results in the form of frequency calibration tables. Current status of these efforts is described.

Wells, J. S.↗

Combustion gas properties. 2: Natural gas fuel and dry air

A series of computations has been made to produce the equilibrium temperature and gas composition for natural gas fuel and dry air. The computed tables and figures provide combustion gas property data for pressures from 0.5 to 50 atmospheres and equivalence ratios from 0 to 2.0. Only samples tables and figures are provided in this report. The complete set of tables and figures is provided on four microfiche films supplied with this report.

Wear, J. D.↗

A New CO2 Transmittance Parameterization and Its Impact on the GLA GCM

The Wu-Kaplan radiation parameterization (Krishnamurthy, 1982) used in the GLA Global Circulation Model (GCM) was improved by replacing its fixed tables of CO2 transmittance in the 15 micron band with models developed by regression on line-by-line transmittances. The transmittances between layers are modeled as products of effective sublayer transmittances. The GLA GCM was integrated for 20 days starting at OZ, January 21, 1979, using the transmittance model. In the control run the fixed table of 15 micron CO2 transmittances is used. The effect of the change of initial cooling rate is illustrated by a map of the difference of 50 mb temperature after 6 hours. The cooling is reduced over high topography, where the fixed table underestimates the transmittance, and is reduced slightly throughout the tropics and the north polar area where the stratosphere is relatively cold. Over elevated topography the surface cooling increases, also as expected. The stratospheric temperature increases over a degree in the arctic and smaller amounts over Antarctica and elsewhere. Tropospheric equilibrium temperature response is obscured by time dependent differences in synoptic disturbances.

Wobus, R.↗

Benchmark data on the separability among crops in the southern San Joaquin Valley of California

Landsat MSS data were input to a discriminant analysis of 21 crops on each of eight dates in 1979 using a total of 4,142 fields in southern Fresno County, California. The 21 crops, which together account for over 70 percent of the agricultural acreage in the southern San Joaquin Valley, were analyzed to quantify the spectral separability, defined as omission error, between all pairs of crops. On each date the fields were segregated into six groups based on the mean value of the MSS7/MSS5 ratio, which is correlated with green biomass. Discriminant analysis was run on each group on each date. The resulting contingency tables offer information that can be profitably used in conjunction with crop calendars to pick the best dates for a classification. The tables show expected percent correct classification and error rates for all the crops. The patterns in the contingency tables show that the percent correct classification for crops generally increases with the amount of greenness in the fields being classified. However, there are exceptions to this general rule, notably grain.

Morse, A.↗

Confidence limits for small numbers of events in astrophysical data

The calculation of limits for small numbers of astronomical counts is based on standard equations derived from Poisson and binomial statistics; although the equations are straightforward, their direct use is cumbersome and involves both table-interpolations and several mathematical operations. Convenient tables and approximate formulae are here presented for confidence limits which are based on such Poisson and binomial statistics. The limits in the tables are given for all confidence levels commonly used in astrophysics.

Gehrels, N.↗

Identification of a constellation from a position

A table is presented which permits rapid determination of the constellation in which an object is located from its 1875.0 position. Directions for accessing and using the table are given. The historical background to the table's development is briefly stated.

Roman, Nancy G.↗

Permanent-File-Validation Utility Computer Program

Errors in files detected and corrected during operation. Permanent File Validation (PFVAL) utility computer program provides CDC CYBER NOS sites with mechanism to verify integrity of permanent file base. Locates and identifies permanent file errors in Mass Storage Table (MST) and Track Reservation Table (TRT), in permanent file catalog entries (PFC's) in permit sectors, and in disk sector linkage. All detected errors written to listing file and system and job day files. Program operates by reading system tables , catalog track, permit sectors, and disk linkage bytes to vaidate expected and actual file linkages. Used extensively to identify and locate errors in permanent files and enable online correction, reducing computer-system downtime.

Derry, Stephen D.↗

Proposed reference models for ozone

Ozone reference models are proposed here similar to the Keating and Young (1985) models which were prepared for the new COSPAR International Reference Atmosphere. This paper updates tables provided in the Keating and Young ozone model, giving improved monthly zonal mean total column ozone in 10 deg latitude increments, improved monthly zonal mean ozone volume mixing ratios (ppmv) from 20 to 0.003 mb in 10 deg latitude increments, and conversion tables providing ozone vertical structure in other units. Also, a new table is provided giving ozone vertical structure as a function of altitude (from 25 to 80 km), latitude, and month. The models are based on measurements from six contemporary satellite instruments.

Keating, G. M.↗

Programmable Remapper

Input image remapped rapidly and accurately onto different coordinate grid. Analog/digital electronic image-processing system developed to warp input images onto arbitrary coordinate grids at video rates. Advantages of system include antialiasing effect of many-to-one data path and speed of lookup-table operation. Lookup tables reprogrammed easily with help of computer that generates table values from mathematical description of desired transformation. Applications include real-time corrections of distortions in input optics of image sensors, corrections for repeatable nonlinear scanning, and aiding persons of impaired vision by deliberately distorting images onto remaining functional portions of retinas.

Juday, Richard D.↗

Reliability growth modeling analysis of the space shuttle main engines based upon the Weibull process

The Weibull process, identified as the inhomogeneous Poisson process with the Weibull intensity function, is used to model the reliability growth assessment of the space shuttle main engine test and flight failure data. Additional tables of percentage-point probabilities for several different values of the confidence coefficient have been generated for setting (1-alpha)100-percent two sided confidence interval estimates on the mean time between failures. The tabled data pertain to two cases: (1) time-terminated testing, and (2) failure-terminated testing. The critical values of the three test statistics, namely Cramer-von Mises, Kolmogorov-Smirnov, and chi-square, were calculated and tabled for use in the goodness of fit tests for the engine reliability data. Numerical results are presented for five different groupings of the engine data that reflect the actual response to the failures.

Wheeler, J. T.↗

Free-floating experiments in orbiter and space station

Manned spacecraft will never be free of acceleration perturbations due to necessary motions of crewmembers. However, in most cases, the perturbations can be minimized or even isolated from sensitive experiments when required. The principal disturbances and methods of isolation are described. As the crew moves about the spacecraft, no external forces are applied and the average acceleration remains near zero. External force will be exerted when jets are fired for spacecraft attitude control or translation, and these must be transferred to the microgravity experiments. Transitory acceleration and vibration are produced by crew and equipment. The most significant on Orbiter have been wall push-offs used for body translation within the spacecraft, the exercise conducted on a treadmill within the middeck area, closing doors of stowage compartments and the vibration of some machinery, such as a sample centrifuge. For short periods of perhaps a few minutes, crew and equipment motion can be largely inhibited, but not for much longer intervals. It may be necessary to mount especially sensitive experiments on an isolation table, which can greatly reduce the acceleration transferred to the experiment. Either weak mechanical springs or, even better, a computer-controlled electromagnetic suspension can be used to effectively insulate the table from vibration at frequencies above about 0.01 Hz. Another option is to free-float an experiment table within the spacecraft. All of the above-mentioned perturbations can be eliminated for some minutes if the entire experiment package is allowed to free-float within the spacecraft until a wall contact is made. Package acceleration levels should be maintainable below 10(exp -8) g sub o in this way.

Garriott, Owen K.↗