Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “stability analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

High performance, high density hydrocarbon fuels

The fuels were selected from 77 original candidates on the basis of estimated merit index and cost effectiveness. The ten candidates consisted of 3 pure compounds, 4 chemical plant streams and 3 refinery streams. Critical physical and chemical properties of the candidate fuels were measured including heat of combustion, density, and viscosity as a function of temperature, freezing points, vapor pressure, boiling point, thermal stability. The best all around candidate was found to be a chemical plant olefin stream rich in dicyclopentadiene. This material has a high merit index and is available at low cost. Possible problem areas were identified as low temperature flow properties and thermal stability. An economic analysis was carried out to determine the production costs of top candidates. The chemical plant and refinery streams were all less than 44 cent/kg while the pure compounds were greater than 44 cent/kg. A literature survey was conducted on the state of the art of advanced hydrocarbon fuel technology as applied to high energy propellents. Several areas for additional research were identified.

Frankenfeld, J. W.↗
NASA NTRS1979

Experimental study of the flight envelope and research of safety requirements for hang-gliders

The flight mechanic computations were computed, providing both the flight envelopes with all sorts of limits and a fairly precise idea of the influence of several parameters, such as pilot's weight, wing settings, aeroelasticity, etc... The particular problem of luffing dives was thoroughly analyzed, and two kinds of causes were exhibited in both the rules of luffing and aeroelastic effects. The general analysis of longitudinal stability showed a strong link with fabric tension, as expected through Nielsen's and Twaites' theory. Fabric tension strongly depending upon aeroelasticity, that parameter was found to be the most effective design one for positive stability. Lateral stability was found to be very similar in all gliders except perhaps the cylindro-conical. The loss of stability happens in roll at low angle of attack, whereas it happens in yaw at high angle. Turning performance was a bit suprising, with a common maximum value of approximately 55 deg of bank angle for a steady turn.

Laburthe, C.↗
NASA NTRS1981

Development of a simple, self-contained flight test data acquisition system

This paper describes a simple, self-contained flight test data acquisition system. The system makes use of the latest sensor and microprocessor technology available, to reduce overall system costs. Coupled with this is the use of modern control theory techniques allowing minimization of data requirements, as well as flight time requirements. Capability of the system includes primarily stability and performance analysis of general aviation airplanes, although system versatility has been designed into the package. Presented are details of the prototype system constructed, as well as details of the data reduction technique utilized. Preliminary results of the flight test program have also been included which demonstrate the capability of this system.

Renz, R. R. L.↗
NASA NTRS1981

Control system development for an organic Ranking cycle engine

An organic Rankine cycle engine is used as part of a solar thermal power conversion assembly (PCA). The PCA, including a direct-heated cavity receiver and a shaft-mounted alternator, is mounted at the focal point of a parabolic dish concentrator. The engine controls are required to maintain approximately constant values of turbine inlet temperature and shaft speed, despite variation in the concentrated solar power input to the receiver. The controls design approach, system models, and initial stability and performance analysis results are presented herein.

Bergthold, F. M., Jr.↗
NASA NTRS1982

A mathematical model of a single main rotor helicopter for piloted simulation

A mathematical model, suitable for piloted simulation of the flying qualities of helicopters, is a nonlinear, total force and moment model of a single main rotor helicopter. The model has ten degrees of freedom: six rigid body, three rotor flapping, and the rotor rotational degrees of freedom. The rotor model assumes rigid blades with rotor forces and moments radially integrated and summed about the azimuth. The fuselage aerodynamic model uses a detailed representation over a nominal angle of attack and sideslip range of + or - 15 deg., as well as a simplified curve fit at large angles of attack or sideslip. Stabilizing surface aerodynamics are modeled with a lift curve slope between stall limits and a general curve fit for large angles of attack. A generalized stability and control augmentation system is described. Additional computer subroutines provide options for a simplified engine/governor model, atmospheric turbulence, and a linearized six degree of freedom dynamic model for stability and control analysis.

Talbot, P. D.↗
NASA NTRS1983

Aeroelastic tailoring of rotor blades for vibration reduction in forward flight

Modern structural optimization techniques are applied to vibration reduction of helicopter rotor blades in forward flight. The objective function minimized consists of the oscillatory vertical hub shears or the hub rolling moments at one particular advance ratio. The behavior constraints are the frequency placements of the blade and the requirement that aeroelastic stability margins, in hover, remain unaffected by the optimization process. The aeroelastic stability and response analysis is based on a fully coupled flap-lag-torsional analysis of the blade. The vertical hub shears and rolling moments used as the objective function are obtained by appropriate integration of the loads acting along the span of the blade combined with a transformation to a hub fixed coordinate system, and a summation over the total number of blades. Numerical results for both a stiff-in-plane and a soft-in-plane configuration are presented, indicating that structural optimization yields the highest benefits when applied to soft-in-plane blade configuration. The results indicate substantial (15-40 percent) reduction in vibration levels, as well as a blade which is 20 percent lighter than the initial design.

Friedmann, P. P.↗
NASA NTRS1983

Effects of friction dampers on aerodynamically unstable rotor stages

Attention is given to the physical concepts and mathematical techniques useful in the analysis of the stabilizing effect of friction on aerodynamically unstable rotor stages. Results are presented for three-, four-, and five-bladed disks. In the present multidegree-of-freedom model of an aerodynamically unstable rotor stage, a harmonic steady state solution due to the friction dampers may be either a stability limit, a stable cycle limit, or neither. A criterion is established in the form of an energy function which determines whether the solution is a stability limit. In the event that the initial displacement and velocity exeed those associated with the steady state solution corresponding to a stability limit, the reponse becomes unbounded.

Griffin, J. H.↗
NASA NTRS1984

Investigation of dynamic noise affecting geodynamics information in a tethered subsatellite

The effects of a tethered satellite system's internal dynamics on the subsatellite were calculated including both overall motions (libration and attitude oscillations) and internal tether oscillations. The SKYHOOK tether simulation program was modified to operate with atmospheric density variations and to output quantities of interest. Techniques and software for analyzing the results were developed including noise spectral analysis. A program was begun for computing a stable configuration of a tether system subject to air drag. These configurations will be of use as initial conditions for SKYHOOK and, through linearized analysis, directly for stability and dynamical studies. A case study in which the subsatellite traverses an atmospheric density enhancement confirmed some theoretical calculations, and pointed out some aspects of the interaction with the tether system dynamics.

Gullahorn, G. E.↗
NASA NTRS1984

Optimum design of rotor blades for vibration reduction in forward flight

Modern structural optimization techniques are applied to vibration reduction of helicopter rotor blades in forward flight. The objective function minimized consists of the oscillatory vertical hub shears or the hub rolling moments at one particular advance ratio. The behavior constraints are the frequency placements of the blade and the requirement that aeroelastic stability margins, in hover, remain unaffected by the optimization process. The aeroelastic stability and response analysis is based on a fully coupled flap-lag-torsional analysis of the blade. Numerical results are presented for some typical soft-in-plane hingeless rotor configurations indicating a 15-40 percent reduction in vibration levels, as well as a blade which is 20 percent lighter than the initial design. These results imply that structural optimization techniques can yield substantial practical benefits in the design process of rotor systems.

Friedmann, P. P.↗
NASA NTRS1984

The dynamic fission instability and the origin of the Moon

A theory for the formation of the Moon which involves the dynamic fission of a rapidly rotating protoplanet, which might then result in the formation of the Earth and the Moon is discussed. The fission hypothesis was originally based on analytic, linearized models of the growth of asymmetry in homogenous bodies. The fully nonlinear evolution of the dynamic instability in inviscid, compressible bodies was calculated by numerical techniques. It was found that the dynamic instability degenerates into the ejection of a ring of matter with a substantial fraction of the mass, leaving behind a central body with most of the mass. The linearized analytical approach and the numerical approach were used to show that dynamic fission probably does not occur in rocky protoplanets. The numerical calculations are performed with a fully three dimensional hydrodynamical code, which allows the nonlinear, time evolution of the instability to be followed. Sequences of uniformly rotating equilibria were constructed and are used as the initial models for the fission calculations. An initially imposed asymmetry consisting of a 10% binary perturbation in the density was found to disappear on the rotational period time scale. No dynamic instability occurred. This result are verified by including the velocity dissipation terms in the linearized analysis of the stability of a Maclaurin spheroid: the dynamic instability disappears when the simulated viscous dissipation terms are included. It is concluded that any rocky body, even with considerable partial melt or a molten core, should be stable to dynamic fission; any rotational instability that occurs can only result in equatorial mass loss.

Boss, A. P.↗
NASA NTRS1985

Vibration/Libration Interaction Dynamics During the Orbiter Based Deployment of Flexible Members

Essential features of a general formulation for studying librational dynamics of a large class of spacecraft during deployment of flexible members are reviewed. The formulation is applicable to a variety of missions ranging from deployment of antennas, booms and solar panels to manufacturing of trusses for space platforms using the space shuttle. The governing nonlinear, non-autonomous and coupled equations of motion are extremely difficult to solve even with the help of a computer, not to mention the cost involved. To get some appreciation as to the complex interactions between flexibility, deployment and attitude dynamics as well as to help pursue stability and control analysis, the equations are linearized about their nominal deflected equilibrium configuration. The procedure is applied to the Space Shuttle based deployment of boom and plate-like members. Results suggest substantial influence of the inertia parameter, flexural rigidity of the appendages, orbit eccentricity, deployment velocity, initial conditions, etc. on the system response. The results should prove useful in planning of the Orbiter based experiments aimed at assessing effectiveness of procedures for studying dynamics and control of flexible orbiting members.

Modi, V. J.↗
NASA NTRS1986

Measurement of H2O and other trace gases in the stratosphere using a high resolution far-infrared spectrometer at 28 KM

The highlights of the stratospheric program were reviewed for the past 2.5 years. The major efforts were analysis of the data from the BIC-2 campaign, and the building or new instrumentation to replace that lost at the end of BIC-2. For clarity, the review will be done by topic, rather than chronologically: construction of the initial far-infrared spectrometer, balloon slight program, laboratory measurement, data analysis, and duplicate stabilized platform.

Traub, W. A.↗
NASA NTRS1987

The dynamic aspects of thermo-elasto-viscoplastic snap-through and creep buckling phenomena

Use of a mathematical model and solution methodology, to examine dynamic buckling and dynamic postbuckling behavior of shallow arches and spherical caps made of a realistic material and undergoing non-isothermal, elasto-viscoplastic deformation was examined. Thus, geometric as well as material type nonlinearities of higher order are included in this analysis. The dynamic stability problem is studied under impulsive loading and suddenly applied loading with loads of constant magnitude and infinite duration. A finite element model was derived directly from the incrementally formulated nonlinear shell equations, by using a tensor-oriented procedure. As an example of the results, the time history of the midspan displacement of a damped shallow circular arch is presented.

Riff, R.↗
NASA NTRS1987

The method of projected characteristics for the evolution of magnetic arches

A numerical method of solving fully nonlinear MHD equation is described. In particular, the formulation based on the newly developed method of projected characteristics (Nakagawa, 1981) suitable to study the evolution of magnetic arches due to motions of their foot-points is presented. The final formulation is given in the form of difference equations; therefore, the analysis of numerical stability is also presented. Further, the most important derivation of physically self-consistent, time-dependent boundary conditions (i.e. the evolving boundary equations) is given in detail, and some results obtained with such boundary equations are reported.

Nakagawa, Y.↗
NASA NTRS1987

Particle paths and phase plane for time-dependent similarity solutions of the one-dimensional Vlasov-Maxwell equations

The phase trajectories of particles in a plasma described by the one-dimensional Vlasov-Maxwell equations are determined qualitatively, analyzing exact general similarity solutions for the cases of temporally damped and growing (sinusoidal or localized) electric fields. The results of numerical integration in both untransformed and Lie-group point-transformed coordinates are presented in extensive graphs and characterized in detail. The implications of the present analysis for the stability of BGK equilibria are explored, and the existence of nonlinear solutions arbitrarily close to and significantly different from the BGK solutions is demonstrated.

Roberts, Dana Aaron↗
NASA NTRS1989

Turbomachinery aeroelasticity at NASA Lewis Research Center

The turbomachinery aeroelastic effort is focused on unstalled and stalled flutter, forced response, and whirl flutter of both single rotation and counter rotation propfans. It also includes forced response of the Space Shuttle Main Engine (SSME) turbopump blades. Because of certain unique features of propfans and the SSME turbopump blades, it is not possible to directly use the existing aeroelastic technology of conventional propellers, turbofans or helicopters. Therefore, reliable aeroelastic stability and response analysis methods for these propulsion systems must be developed. The development of these methods for propfans requires specific basic technology disciplines, such as 2-D and 3-D steady and unsteady aerodynamic theories in subsonic, transonic and supersonic flow regimes; modeling of composite blades; geometric nonlinear effects; and passive and active control of flutter and response. These methods are incorporated in a computer program, ASTROP. The program has flexibility such that new and future models in basic disciplines can be easily implemented.

Kaza, Krishna Rao V.↗
NASA NTRS1989

Analytic simulation of higher harmonic control using a new aeroelastic model

This paper describes a higher harmonic control (HHC) study of a four bladed hingeless rotor using a coupled flap-lag-torsional aeroelastic stability and response analysis which incorporates finite-state, time-domain aerodynamics. The rotor trim condition is determined using a coupled trim-aeroelastic analysis. Deterministic and cautious controllers based on local and global HHC models are implemented with different combinations of input parameters identified using a Kalman filter. The effects of unsteady versus quasisteady aerodynamic modeling on HHC simulations are investigated, including the effectiveness of the local and global HHC models and the advantages of different identification schemes.

Friedmann, P. P.↗
NASA NTRS1989

An efficient cell-vertex multigrid scheme for the three-dimensional Navier-Stokes equations

A cell-vertex scheme for the three-dimensional Navier-Stokes equations, which is based on central difference approximations and Runge-Kutta time stepping, is described. Using local time stepping, implicit residual smoothing with locally varying coefficients, a multigrid method and carefully controlled dissipative terms, very good convergence rates are obtained for two- and three-dimensional flows. Details of the acceleration techniques, which are important for convergence on meshes with high aspect-ratio cells, are discussed. Emphasis is put on the analysis of the stability properties of the implicit smoothing of the explicit residuals with coefficients, which depend on cell aspect ratios.

Radespiel, R.↗