SEARCH · Engineering Papers

Results for “separators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Three-dimensional turbulent boundary layer development and separation in V/STOL engine inlets at incidence with small-cross flow and curvature influences

The study concerns the influence of the three-dimensional cross flows on the compressible turbulent boundary layer development and flow separation prediction around V/STOL engine inlets at high incidence. The governing equations for the three-dimensional boundary layer flow with small-cross approximation are solved numerically on an intrinsic streamline coordinate system. Results are presented to illustrate the effects of small cross-flow, compressibility and streamline curvatures on the flow. Comparisons of the results with the wind tunnel data for scaled model and with data obtained from another existing compressible axisymmetric turbulent boundary layer scheme are included in the analysis.

Chou, D. C.↗

NASA NTRS1981

Dry-surface coating method for visualization of separation on a bluff body

A simple and relatively accurate dry-surface coating method for visualization of the flow separation on a circular cylinder (or any bluff body) during wind tunnel tests is described. The technique consists of (1) application of a thin coating composed of an indicator and a paint carrier; (2) drying of the film; (3) conditioning of the coating with an acidic solution to ensure a suitable color reaction; (4) release into the body wake of a gas able to produce a base through chemical reaction with the solvent of the conditioning solution; and (5) color reaction according to pH.

Sadeh, W. Z.↗

NASA NTRS1981

A modal separation measurement technique for broadband noise propagating inside circular ducts

A measurement technique which separates broadband noise propagating inside circular ducts into the acoustic duct modes is developed. The technique is also applicable to discrete frequency noise. The acoustic modes are produced by weighted combinations of the instantaneous outputs of microphones spaced around the duct circumference. The technique is compared with the cross spectral density approach presently available and found to have certain advantages, and disadvantages. Considerable simplification of both the new technique and the cross spectral density approach occurs when no correlation exists between different circumferential mode orders. The properties leading to uncorrelated modes and experimental tests which verify this condition are discussed. The modal measurement technique is applied to the case of broadband noise generated by flow through a coaxial obstruction (nozzle or orifice) in a pipe. Different circumferential mode orders are shown to be uncorrelated for this type of noise source.

Kerschen, E. J.↗

NASA NTRS1982

Separating Silicon From Si/NaF Mixtures

New method of extracting silicon from mixture produced when silicon tetrafluoride is reduced by sodium takes advantage of lower melting point of NaF. Method is effective at temperatures up to 400 degrees C below melting point of Si. Results in energy and economic savings: simpler and smaller furnaces, less volatization loss, and high percentage of separation.

Sanjurjo, A.↗

NASA NTRS1983

Separating Silicon and Sodium Fluoride by Melting

Silion is withdrawn from bottom of crucible, once two immiscible liquid stages form, in quasi-continuous method of separating silicon from other reaction products. Process is periodically halted to remove accumulated buildup of salts.

Nanis, L.↗

NASA NTRS1981

Oil-flow separation patterns on an ogive forebody

Oil flow patterns on a symmetric tangent ogive forebody having a fineness ratio of 3.5 are presented for angles of attack up to 88 deg at a transitional Reynolds number of 8 million (based on base diameter) and a Mach number of 0.25. Results show typical surface flow separation patterns, the magnitude of surface flow angles, and the extent of laminar and turbulent flow for symmetric, asymmetric, and wakelike flow regimes.

Keener, E. R.↗

NASA NTRS1981

A vortex-filament and core model for wings with edge vortex separation

A method for predicting aerodynamic characteristics of slender wings with edge vortex separation was developed. Semiempirical but simple methods were used to determine the initial positions of the free sheet and vortex core. Comparison with available data indicates that: the present method is generally accurate in predicting the lift and induced drag coefficients but the predicted pitching moment is too positive; the spanwise lifting pressure distributions estimated by the one vortex core solution of the present method are significantly better than the results of Mehrotra's method relative to the pressure peak values for the flat delta; the two vortex core system applied to the double delta and strake wing produce overall aerodynamic characteristics which have good agreement with data except for the pitching moment; and the computer time for the present method is about two thirds of that of Mehrotra's method.

Pao, J. L.↗

NASA NTRS1982

A vortex-filament and core model for wings with edge vortex separation

A vortex filament-vortex core method for predicting aerodynamic characteristics of slender wings with edge vortex separation was developed. Semi-empirical but simple methods were used to determine the initial positions of the free sheet and vortex core. Comparison with available data indicates that: (1) the present method is generally accurate in predicting the lift and induced drag coefficients but the predicted pitching moment is too positive; (2) the spanwise lifting pressure distributions estimated by the one vortex core solution of the present method are significantly better than the results of Mehrotra's method relative to the pressure peak values for the flat delta; (3) the two vortex core system applied to the double delta and strake wings produce overall aerodynamic characteristics which have good agreement with data except for the pitching moment; and (4) the computer time for the present method is about two thirds of that of Mehrotra's method.

Pao, J. L.↗

NASA NTRS1982

Development of STS/Centaur failure probabilities liftoff to Centaur separation

The results of an analysis to determine STS/Centaur catastrophic vehicle response probabilities for the phases of vehicle flight from STS liftoff to Centaur separation from the Orbiter are presented. The analysis considers only category one component failure modes as contributors to the vehicle response mode probabilities. The relevant component failure modes are grouped into one of fourteen categories of potential vehicle behavior. By assigning failure rates to each component, for each of its failure modes, the STS/Centaur vehicle response probabilities in each phase of flight can be calculated. The results of this study will be used in a DOE analysis to ascertain the hazard from carrying a nuclear payload on the STS.

Hudson, J. M.↗

NASA NTRS1981

Booster separation motor

The design, development, fabrication, testing, evaluation and flight qualification of the space shuttle booster separation motor is discussed. Delivery of flight hardware to support the research and development flights of the space shuttle is discussed.

Source record↗

NASA NTRS1980

Evaluation of the procedure for separating barley from other spring small grains

The success of the Transition Year procedure to separate and label barley and the other small grains was assessed. It was decided that developers of the procedure would carry out the exercise in order to prevent compounding procedural problems with implementation problems. The evaluation proceeded by labeling the sping small grains first. The accuracy of this labeling was, on the average, somewhat better than that in the Transition Year operations. Other departures from the original procedure included a regionalization of the labeling process, the use of trend analysis, and the removal of time constraints from the actual processing. Segment selection, ground truth derivation, and data available for each segment in the analysis are discussed. Labeling accuracy is examined for North Dakota, South Dakota, Minnesota, and Montana as well as for the entire four-state area. Errors are characterized.

Magness, E. R.↗

NASA NTRS1970

Process of treating cellulosic membrane and alkaline with membrane separator

The improvement of water-soluble cellulose ether membranes for use as separators in concentrated alkaline battery cells is discussed. The process of contacting membranes with an aqueous alkali solution of concentration less than that of the alkali solution to be used in the battery but above that at which the membrane is soluble is described.

Hoyt, H. E.↗

NASA NTRS1970

Separator for alkaline batteries and method of making same

The preparation of membranes suitable for use as separators in concentrated alkaline battery cells by selective solvolysis of copolymers of methacrylate esters with acrylate esters followed by addition of a base and to the resultant products is described. The method of making copolymers by first copolymerizing a methacrylate ester (or esters) with a more readily hydrolyzable ester, followed by a selective saponification whereby the methacrylate ester moieties remain essentially intact and the readily hydrolyzable ester moiety is suponified and to the partial or complete neutralization of the relatively brittle copolymer acid with a base to make membranes which are sufficiently flexible in the dry state so that they may be wrapped around electrodes without damage by handling is described.

Hoyt, H. E.↗

NASA NTRS1970

Separator for alkaline electric cells and method of making

Modified cellulose ether films having an increased electrolytic conductivity and a useable flexibility and in certain instances an increased flexibility are presented. Battery separator membranes comprising a cellulose ether and a minor proportion of a compatible water soluble base selected from the group consisting of alkali metal and ammonium hydroxides, aliphatic amines, and aliphatic hydroxyamines are used.

Pfluger, H. L.↗

NASA NTRS1982

Flows over wings with leading-edge vortex separation

The unsteady cross flow analogy reduces the steady three dimensional separation flow problem into an unsteady two dimensional flow problem in which the section shape changes with time. The two dimensional VORSEP code is extended to the case of arbitrary body growth rates in order to generate the initial vortex structures for the three dimensional free vortex sheet (FVS) code. Automatic procedures to reduce the wing geometry definition to a set of cross flow plane sections corresponding to the locations of the time step solutions and to generate the effective source distribution on each cross flow section to represent the section normal growth across the following steps are incorporated in the VORSEP code. Also, the wake shedding model is improved by adopting a redistribution scheme which improves the stability of the free sheet development with time. The improved wake shedding model combined with the redistribution scheme alleviated the numerical instabilities associated with the vortex rollup.

Rao, B. M.↗

NASA NTRS1982

Membrane separation technology in the 1980s

The current status of membrane technology is assessed and industrial processes in which membrane technology could effect energy savings or other advantages are identified. The extension of current trends is recommended; i.e., the development of ultrathin and highly permselective membranes, the use of specific carriers to enhance permselectivity and permit 'uphill' diffusion, and the improvement of separation efficiency. Membranes are predicted to be important in biotechnology and in the production of solar energy. Guidelines indicating where and how to look for opportunities where evolving membrane technology might fit are provided.

Lonsdale, H. K.↗

NASA NTRS1979

Phase separation in transparent liquid-liquid miscibility gap systems

A program to be carried out on transparent liquid-phase miscibility gap materials was developed for the purpose of acquiring additional insight into the separation process occurring in these systems. The transparency feature allows the reaction to be viewed directly through light scattering and holographic methods.

Gelles, S. H.↗

NASA NTRS1982

Mineral separation and recycle in a Controlled Ecological Life Support System (CELSS)

The background of the mineral nutrition needs of plants are examined along with the applicability of mineral control and separation to a controlled ecological life support system (CELSS). Steps that may be taken in a program to analytically define and experimentally test key mineral control concepts in the nutritional and waste processing loops of a CELSS are delineated.

Ballou, E. V.↗