Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “passivation layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Microstructural Passivation of Patterned Al 2 O 3 Back Contacts on CdS/CdTe Solar Cells

Abstract Patterned aluminum oxide (Al 2 O 3 ) back contact on cadmium telluride (CdTe) solar cells can effectively mitigate the loss of the majority carriers while retaining the passivation benefits for minority carriers. This study investigates the impact of the point‐contact geometry on cell performance, where the spacing of the microholes is systematically varied at a constant microhole diameter (≈16 µm). Microhole arrays are created on an evaporated Al 2 O 3 layer (≈30 nm) on CdTe using laser‐beam lithography and selective wet etching processes. Comparative analysis indicates a significant decrease in fill factor (FF) and short‐circuit current ( I SC ) when the contact fraction falls below 30%, likely due to the Al 2 O 3 barrier impeding majority carriers. Above this fraction, FF and I SC are comparable to those of baseline CdTe cells without Al 2 O 3 . Open‐circuit voltage ( V OC ) shows a gradual decrease as Al 2 O 3 coverage is reduced but exhibits a slight increase (<15 mV) when the contact fraction exceeds 30%. Cathodoluminescence (CL) characterization reveals that significantly improved radiative recombination occurs within the CdTe grain bulk with Al 2 O 3 , whereas this effect on grain boundaries is minimal. The findings imply complex local carrier dynamics in the patterned back‐contact region, closely tied to the microstructural properties of CdTe‐based solar cells.

Roy, Etee Kawna↗

Investigation of the diffusion behavior of sodium in Cu(In,Ga)Se{sub 2} layers

Sodium diffusion in Cu(In,Ga)Se{sub 2} (CIGS) layers was investigated over a temperature range from 157 °C to 400 °C. The diffusion profiles were measured by secondary ion mass spectrometry. Sodium ions diffused from a sodium fluoride (NaF) layer on the CIGS surface into the CIGS layer. From Na diffusion profiles, the diffusion along grain boundaries could be distinguished from the diffusion into the grain interior. Atom-probe tomography measurements reveal that even at a low temperature of 157 °C bulk diffusion of sodium into CIGS occurs. Based on this data, the slower diffusion coefficient in the volume can be described by the Arrhenius equation D{sub Na}{sup V} = 9.7 × 10{sup −9} exp(−0.36 eV/k{sub B}T) cm{sup 2} s{sup −1} and the fast diffusion along the grain boundaries by D{sub Na}{sup GB} = 6.5 × 10{sup −9} exp(−0.21 eV/k{sub B}T) cm{sup 2} s{sup −1}. Hence, we propose that sodium ions do not only passivate grain boundaries, but also act as dopants in the CIGS bulk.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The art and science of flow control

The ability to actively or passively manipulate a flow field to effect a desired change is of immense technological importance. In this article, methods of control to achieve transition delay, separation postponement, lift enhancement, drag reduction, turbulence augmentation, or noise suppression are considered. Emphasis is placed on external boundary-layer flows although applicability of some of the methods reviewed for internal flows will be mentioned. Attempts will be made to present a unified view of the different methods of control to achieve a variety of end results. Performance penalties associated with a particular method such as cost, complexity, or trade-off will be elaborated.

Gad-El-hak, Mohamed↗

Towards Soil Moisture Profile Estimation in the Root Zone Using L- and P-Band Radiometer Observations: A Coherent Modelling Approach

Precision irrigation management and crop water stress assessment rely on accurate estimation of root zone soil moisture. However, only the top 5cm soil moisture can be estimated using the two current passive microwave satellite missions, Soil Moisture and Ocean Salinity (SMOS) and Soil Moisture Active Passive (SMAP), which operate at L-band (wavelength of ~21cm). Since the contributing depth of the soil to brightness temperature increases with observation wavelength, it is expected that a P-band (wavelength of ~40cm) radiometer could potentially provide soil moisture information from deeper layers of the soil profile. Moreover, by combining both L- and P- bands, it is hypothesized that the soil moisture profile can be estimated even beyond their individual observation depths. The aim of this study was to demonstrate the potential of combined L-band and P-band radiometer observations to estimate the soil moisture profile under flat bare soil using a stratified coherent forward model. Brightness temperature observations at L-band and P-band from a tower based experimental site across a dry (April 2019) and a wet (March 2020) period, covering different soil moisture profile shapes, were used in this study. Results from an initial synthetic study showed that the performance of a combined L-band and P-band approach was better than the performance of using either band individually, with an average depth over which reliable soil moisture profile information could be estimated (i.e. with a target root mean square error (RMSE) of less than 0.04 m3/m3) being 20cm for linear and 15cm for second-order polynomial functions. Other functions were also tested but found to have a poorer performance. Applying the method to the tower-based brightness temperature achieved an average estimation depth of 28cm (20cm) and 5cm (5cm) during the dry and wet periods respectively when using a second-order polynomial (linear) function. These findings highlight the opportunity of a satellite mission with L-band and P-band observations to accurately estimate the soil moisture profile to as deep as 30cm globally.

Foad Brakhasi↗

Benefit of Modeling the Observation Error in a Data Assimilation Framework Using Vegetation Information Obtained From Passive Based Microwave Data

A primary operational goal of the United States Department of Agriculture (USDA) is to improve foreign market access for U.S. agricultural products. A large fraction of this crop condition assessment is based on satellite imagery and ground data analysis. The baseline soil moisture estimates that are currently used for this analysis are based on output from the modified Palmer two-layer soil moisture model, updated to assimilate near-real time observations derived from the Soil Moisture Ocean Salinity (SMOS) satellite. The current data assimilation system is based on a 1-D Ensemble Kalman Filter approach, where the observation error is modeled as a function of vegetation density. This allows for offsetting errors in the soil moisture retrievals. The observation error is currently adjusted using Normalized Difference Vegetation Index (NDVI) climatology. In this paper we explore the possibility of utilizing microwave-based vegetation optical depth instead.

Vegetation↗

Investigation of long-term light stability of negative charge injected into oxide-nitride-oxide passivation stack of crystalline silicon solar cells

A negatively charged oxide-nitride-oxide stack for field-effect passivation of crystalline silicon solar cells is discussed. The negative charge was injected into the stack by a plasma charge injection technology. Charge stability was studied by exposing samples to AM1.5 simulation visible light and full-spectrum light at temperatures ranging from 55 to 78 °C for up to 300 h. Charge injection and loss were quantified based on shifts in the flatband voltage of capacitance–voltage curves measured with a mercury probe. The most probable mechanism of charge loss was found to be diffusion of negative charged hydrogen atoms through nitride and bottom oxide. The optimum recipe for each layer of the stack was investigated to minimize the loss of injected charge. The flatband voltage decay of the optimized stack was found to fit a power-law trend, suggesting the dispersive transport of hydrogen atoms with a dispersion parameter of ~0.06–0.07. The optimized stack is projected to maintain a negative charge density of about 3.6 × 10 12 cm –2 or more after 25 years of field operation in an environment such as Arizona, which would be sufficient for field-effect passivation under one-sun illumination. Furthermore, the high stability of the negative injected charge makes the plasma charging technology a safer and lower cost alternative to Al 2 O 3 -passivation technology commonly used to passivate p-type surfaces.

14 SOLAR ENERGY↗

Charge trapping properties of Ge nanocrystals grown via solid-state dewetting

In the present work, we report on the charge trapping properties of Germanium Nanocrystals (Ge NCs) self assembled on SiO 2 thin layer for promising applications in next-generation non volatile memory by the means of Deep Level Transient Spectroscopy (DLTS) and high frequency C-V method. The Ge NCs were grown via dewetting phenomenon at solid state by Ultra-High Vacuum (UHV) annealing and passivated with silicon before SiO 2 capping. The role of the surface passivation is to reduce the electrical defect density at the Ge NCs-SiO 2 interface. The presence of the Ge NCs in the oxide of the MOS capacitors strongly affects the C-V characteristics and increases the accumulation capacitance, causes a negative flat band voltage (VFB) shift. The DLTS has been used to study the individual Ge NCs as a single point deep level defect in the oxide. DLTS reveals two main features: the first electron traps around 255 K could correspond to dangling bonds at the Si/SiO2 interface and the second, at high-temperature (>300 K) response, could be originated from minority carrier generation in Ge NCs.

36 MATERIALS SCIENCE↗

Lead-chelating hole-transport layers for efficient and stable perovskite minimodules

The defective bottom interfaces of perovskites and hole-transport layers (HTLs) limit the performance of p-i-n structure perovskite solar cells. We report that the addition of lead chelation molecules into HTLs can strongly interact with lead(II) ion (Pb 2+ ), resulting in a reduced amorphous region in perovskites near HTLs and a passivated perovskite bottom surface. Here, the minimodule with an aperture area of 26.9 square centimeters has a power conversion efficiency (PCE) of 21.8% (stabilized at 21.1%) that is certified by the National Renewable Energy Laboratory (NREL), which corresponds to a minimal small-cell efficiency of 24.6% (stabilized 24.1%) throughout the module area. Small-area cells and large-area minimodules with lead chelation molecules in HTLs had a light soaking stability of 3010 and 2130 hours, respectively, at an efficiency loss of 10% from the initial value under 1-sun illumination and open-circuit voltage conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of ~25% Efficient Double Side Screen Printed Poly-Si/SiO x Passivated Contact Solar Cells

This program aims to overcome these challenges and develop high-efficiency (24-25%) double-side (DS) TOPCon solar cells by maximizing passivation on both sides while mitigating light absorption losses. To achieve this, the program will implement either thin (≤ 20 nm) homogeneous n-TOPCon on the entire front surface or selective area thick (≥ 100 nm) n-TOPCon only underneath the front metal contact with ~90% field region composed of dielectric passivated textured n-Si in between the poly-Si/metal grid. The rear side will feature ~250 nm-thick full-area planar p-TOPCon, which functions as the rear junction. Recombination and parasitic absorption losses in the front and rear TOPCon layers will be minimized by tailoring their doping profiles and thickness. Additionally, the device performance will be further enhanced through the optimization of bulk parameters, including the carrier lifetime, resistivity, and thickness of the n-type Si absorber. Finally, advanced metallization techniques, such as fine-line printing, and floating busbar or busbar-less designs, will be employed to reduce recombination, resistive, and optical losses. The program started with the development of a technology roadmap for DS-TOPCon cells to achieve target efficiency.

14 SOLAR ENERGY↗

Structure of the moon

Seismic data fron the four stations of the Apollo passive seismic network have been analyzed to obtain the velocity structure of the moon. Analysis of body wave phases from artificial impacts of known impact time and position yields a crustal section. In the Mare Cognitum region the crust is about 60 km thick and is layered. In the 20-km-thick upper layer, velocity gradients are high and microcracks may play an important role. The 40-km-thick lower layer has a nearly constant 6.8-km/sec velocity. There may be a thin high-velocity layer present beneath the crust. The determination of seismic velocities in the lunar mantle is attempted by using natural impacts and deep moonquakes. The simplest model that can be proposed for the mantle consists of a 'lithosphere' overlying an 'asthenosphere'.

Toksoz, M. N.↗

18-percent efficient terrestrial silicon solar cells

Silicon solar cells are described which operate at energy conversion efficiencies in excess of 18 percent under standard terrestrial test conditions (AM1.5, 100 mW/sq cm, 28 C). These are believed to be the most efficient silicon cells reported to date. The high efficiency is a result of the combination of high open-circuit voltage due to the careful attention paid to passivation of the top surface of the cell; high fill factors due to the high open-circuit voltage and low parasitic resistance losses; and high short-circuit current due to the use of shallow diffusions, a low grid coverage, and an optimized double-layer antireflection coating.

Blakers, A. W.↗

High-efficiency silicon solar cells

Silicon solar cells are described which operate at energy conversion efficiencies independently measured at 18.7 percent under standard terrestrial test conditions (AM1.5, 100 mW/sq cm, 28 C). These are apparently the most efficient silicon cells fabricated to date. The high-efficiency results from a combination of high open-circuit voltage due to the careful attention paid to the passivation of the top surface of the cell, high fill factor due to the high open-circuit voltage and low parasitic resistance losses, and high short-circuit current density due to the use of shallow diffusions, a low grid coverage, and an optimized double layer antireflection coating.

Green, M. A.↗

Modeling the Impact of Drizzle and 3D Cloud Structure on Remote Sensing of Effective Radius

Remote sensing of cloud particle size with passive sensors like MODIS is an important tool for cloud microphysical studies. As a measure of the radiatively relevant droplet size, effective radius can be retrieved with different combinations of visible through shortwave infrared channels. MODIS observations sometimes show significantly larger effective radii in marine boundary layer cloud fields derived from the 1.6 and 2.1 pm channel observations than for 3.7 pm retrievals. Possible explanations range from 3D radiative transport effects and sub-pixel cloud inhomogeneity to the impact of drizzle formation on the droplet distribution. To investigate the potential influence of these factors, we use LES boundary layer cloud simulations in combination with 3D Monte Carlo simulations of MODIS observations. LES simulations of warm cloud spectral microphysics for cases of marine stratus and broken stratocumulus, each for two different values of cloud condensation nuclei density, produce cloud structures comprising droplet size distributions with and without drizzle size drops. In this study, synthetic MODIS observations generated from 3D radiative transport simulations that consider the full droplet size distribution will be generated for each scene. The operational MODIS effective radius retrievals will then be applied to the simulated reflectances and the results compared with the LES microphysics.

Platnick, Steven↗

The NASA Eulerian Snow on Sea Ice Model (NESOSIM) v1.0: initial model development and analysis

The NASA Eulerian Snow On Sea Ice Model (NESOSIM) is a new, open-source snow budget model that is currentlyconfigured to produce daily estimates of the depth and density of snow on sea ice across the Arctic Ocean throughthe accumulation season. NESOSIM has been developed in a three-dimensional Eulerian framework and includes two(vertical) snow layers and several simple parameterizations (accumulation, wind packing, advection_divergence, blowingsnow lost to leads) to represent key sources and sinks of snow on sea ice. The model is forced with daily inputs of snowfall and near-surface winds (from reanalyses), sea ice concentration (from satellite passive microwave data) and sea ice drift (from satellite feature tracking) during the accumulation season (August through April). In this study, we present the NESOSIM formulation, calibration efforts, sensitivity studies and validation efforts across an Arctic Ocean domain (100 km horizontal resolution). The simulated snow depth and density are calibrated with in situ data collected on drifting ice stations during the 1980s. NESOSIM shows strong agreement with the in situ seasonal cycles of snow depth and density, and shows good (moderate) agreement with the regional snow depth (density) distributions. NESOSIM is run for a contemporary period (2000 to 2015), with the results showing strong sensitivity to the reanalysis derived snowfall forcing data, with the Modern-Era Retrospective analysis for Research and Applications (MERRA) and the Japanese Meteorological Agency 55-year reanalysis (JRA-55) forced snow depths generally higher than ERA-Interim,and the Arctic System Reanalysis (ASR) generally lower. We also generate and force NESOSIM with a consensus "median" daily snowfall dataset from these reanalyses.The results are compared against snow depth estimates derived from NASA's Operation IceBridge (OIB) snow radar data from 2009 to 2015, showing moderate_strong correlations and root mean squared errors of 10 cm depending on the OIB snow depth product analyzed, similar to the comparisons between OIB snow depths and the commonly used modified Warren snow depth climatology. Potential improvements to this initial NESOSIM formulation are discussed in the hopes of improving the accuracy and reliability of these simulated snow depths and densities.

Petty, Alek A.↗

Passive microwave mapping of ice thickness

Basic calculations are presented for evaluating the feasibility of a scanning microwave radiometer system for mapping the thickness of lake ice. An analytical model for the apparent brightness temperature as a function of ice thickness has been developed, and elaborated to include such variables as galactic and atmospheric noise, aspect angle, polarization, temperature gradient in the ice, the presence of transition layers such as snow, slush, and water, increased loss due to air inclusions in the ice layer, and the presence of multiple ice thicknesses within the antenna footprint. It was found that brightness temperature measurements at six or seven frequencies in the range of 0.4 to 0.7 GHz were required to obtain unambiquous thickness estimates. A number of data processing methods were examined. The effects of antenna beamwidth, scanning rate, receiver bandwidth, noise figure, and integration time were studied.

Apinis, J. J.↗

Selenium Migration and Local Structures in Cu‐Doped CdSeTe Solar Cells after Aging

Selenium grading plays a critical role in state-of-the-art Cadmium Telluride photovoltaic cells by enhancing long-wavelength absorption and extending minority carrier lifetimes —key to enabling the current performance record of 23.08%. However, very little is understood about selenium motion. In this study, a comprehensive, multimodal, and multiscale approach is employed to investigate Se migration and local structural changes in copper (Cu)-doped CdSeTe solar cells subjected to accelerated stress. X-ray fluorescence (XRF) microscopy shows unexpected levels of Se diffusion after 500 h under heat (75°C) and light (0.8 suns, 80 mW/cm 2 ), suggesting the coexistence of fast and slow diffusion channels even at low temperatures, with unexpectedly low activation energies (<0.85 eV). X-ray Absorption Near Edge Structure (XANES) analysis indicates a preferential migration of Se atoms to anionic lattice sites and a reduction in Se-Cl co-passivation at Te-terminated dislocation cores. Furthermore, these findings point to a reconfiguration of Se local environments and highlight the potential role of extended structural defects in enabling Se transport at low temperatures. Additionally, XANES results suggest that the presence of metallic Cu across the absorber layer may contribute to back-contact degradation and reduced hole density in both fresh and aged devices.

14 SOLAR ENERGY↗

A Low-Temperature, Solution Processable Tin Oxide Electron-Transporting Layer Prepared by the Dual-Fuel Combustion Method for Efficient Perovskite Solar Cells

Although tin oxide (SnO 2 ) has been employed recently as an efficient electron-transporter to realize highly efficient organometal halide perovskite solar cells (PVSCs), it is still quite challenging to apply it through facile solution-based synthesis at low enough temperature (<150 °C) to be compatible with the roll-to-roll printing on polymer substrates. In this work, a dual-fuel combustion method has been successfully adapted to modulate the exothermic characteristics and processing temperature (140 °C) of SnO 2 to achieve homogeneous and crystalline thin film as efficient electron-transporting layer for PVSCs. The fabricated SnO 2 film not only has high transparency (from 350 nm to near-infrared region) but also possesses good electron extraction ability, as evidenced by the efficient PL quenching in bilayered SnO 2 /CH 3 NH 3 PbI 3 film. By passivating SnO 2 surface with a C 60 -containing self-assembled monolayer (C 60 -SAM), a high power conversion efficiency (PCE max ) of >15% with negligible hysteresis can be achieved in PVSC. This demonstrates the great potential of applying this dual-fuel combustion process to improve processability and charge-transporting properties of metal oxides for organic electronics applications.

14 SOLAR ENERGY↗

Organo-sulfur molecules enable iron-based battery electrodes to meet the challenges of large-scale electrical energy storage

Rechargeable iron-air and nickel-iron batteries are attractive as sustainable and inexpensive solutions for large-scale electrical energy storage because of the global abundance and eco-friendliness of iron, and the robustness of iron-based batteries to extended cycling. Despite these advantages, the commercial use of iron-based batteries has been limited by their low charging efficiency. This limitation arises from the iron electrodes evolving hydrogen extensively during charging. The total suppression of hydrogen evolution has been a significant challenge. We have found that organo-sulfur compounds with various structural motifs (linear and cyclic thiols, dithiols, thioethers and aromatic thiols) when added in milli-molar concentration to the aqueous alkaline electrolyte, reduce the hydrogen evolution rate by 90%. These organo-sulfur compounds form strongly adsorbed layers on the iron electrode and block the electrochemical process of hydrogen evolution. The charge-transfer resistance and double-layer capacitance of the iron/electrolyte interface confirm that the extent of suppression of hydrogen evolution depends on the degree of surface coverage and the molecular structure of the organo-sulfur compound. An unanticipated electrochemical effect of the adsorption of organo-sulfur molecules is "de-passivation" that allows the iron electrode to be discharged at high current values. The strongly adsorbed organo-sulfur compounds were also found to resist electro-oxidation even at the positive electrode potentials at which oxygen evolution can occur. Through testing on practical rechargeable battery electrodes we have verified the substantial improvements to the efficiency during charging and the increased capability to discharge at high rates. We expect these performance advances to enable the design of efficient, inexpensive and eco-friendly iron-based batteries for large-scale electrical energy storage.

Yang, B↗