Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “load shapes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Stiffness of frictional contact of dissimilar elastic solids

The classic Sneddon relationship between the normal contact stiffness and the contact size is valid for axisymmetric, frictionless contact, in which the two contacting solids are approximated by elastic half-spaces. Deviation from this result critically affects the accuracy of the load and displacement sensing nanoindentation techniques. This study gives a thorough numerical and analytical investigation of corrections needed to the Sneddon solution when finite Coulomb friction exists between an elastic half-space and a flat-ended rigid punch with circular or noncircular shape. Because of linearity of the Coulomb friction, the correction factor is found to be a function of the friction coefficient, Poisson's ratio, and the contact shape, but independent of the contact size. Two issues are of primary concern in the finite element simulations – adequacy of the mesh near the contact edge and the friction implementation methodology. Although the stick or slip zone sizes are quite different from the penalty or Lagrangian methods, the calculated contact stiffnesses are almost the same and may be considerably larger than those in Sneddon's solution. For circular punch contact, the numerical solutions agree remarkably well with a previous analytical solution. For non-circular punch contact, the results can be represented using the equivalence between the contact problem and bi-material fracture mechanics. Finally, the correction factor is found to be a product of that for the circular contact and a multiplicative factor that depends only on the shape of the punch but not on the friction coefficient or Poisson's ratio.

36 MATERIALS SCIENCE↗

Impact of electrode porosity architecture on electrochemical performances of 1 mm-thick LiFePO4 binder-free Li-ion electrodes fabricated by Spark Plasma Sintering

Thick electrodes with high active material loadings have been intensively studied over the last couple of decades in pursuit of achieving high energy density systems. To optimize and enhance the electrochemical performance of such electrodes, one has to control the pore morphology by, for example, varying the pore size and shape, and the level of porosity. In the present work, the fabrication of thick binder-free LiFePO4 (LFP) electrodes with two different pore sizes (12 and 20 mu m) and porosities (21 vol% and 44 vol%) using Spark Plasma Sintering (SPS) and templating approach is reported. The well-controlled porous architecture inside the thick electrodes is realized by fine-tuning experimental parameters. The impact of porosity architecture on electrochemical performance is quantified and correlated with the 3D tortuosity values determined from both micro-computed tomography and electrochemical impedance-based experimental methods. Based on the micro-computed tomography data analysis, estimated tortuosity values along X, Y, and Z axes reveal an anisotropic effect perpendicularly to the SPS compression axis (Z-direction). This is particularly profoundly observed in the samples with larger pores (20 mu m). The correlation between morphological properties and the rate capability performance is established indicating that the capacity loss happens mainly due to the Li-ion diffusion limitations.

Cathode material↗

Hydrogen Adsorption in Ultramicroporous Metal–Organic Frameworks Featuring Silent Open Metal Sites

In this work, we utilized an ultramicroporous metal–organic framework (MOF) named [Ni 3 (pzdc) 2 (ade) 2 (H 2 O) 4 ]·2.18H 2 O (where H 3 pzdc represents pyrazole-3,5-dicarboxylic acid and ade represents adenine) for hydrogen (H 2 ) adsorption. Upon activation, [Ni 3 (pzdc) 2 (ade) 2 ] was obtained, and in situ carbon monoxide loading by transmission infrared spectroscopy revealed the generation of open Ni(II) sites. The MOF displayed a Brunauer–Emmett–Teller (BET) surface area of 160 m 2 /g and a pore size of 0.67 nm. Hydrogen adsorption measurements conducted on this MOF at 77 K showed a steep increase in uptake (up to 1.93 mmol/g at 0.04 bar) at low pressure, reaching a H 2 uptake saturation at 2.11 mmol/g at ~0.15 bar. The affinity of this MOF for H 2 was determined to be 9.7 ± 1.0 kJ/mol. In situ H 2 loading experiments supported by molecular simulations confirmed that H 2 does not bind to the open Ni(II) sites of [Ni 3 (pzdc) 2 (ade) 2 ], and the high affinity of the MOF for H 2 is attributed to the interplay of pore size, shape, and functionality.

08 HYDROGEN↗

Carbide Particle Redistribution in U-10Mo Alloy during Hot and Cold Rolling Processes: Synthetic Microstructure-Based Finite-Element Approach

The influence of initial carbide particle distribution features on particle fracture and the evolution of stringer distribution within an alloy of uranium with 10 weight percent molybdenum during cold rolling was investigated in this study. This work will provide guidance to casting optimization work and identify actionable process changes to eliminate the surface features directly attributed to carbides. In a previous study, various synthetic microstructure-based finite-element (FE) models were generated with consideration of different parameters (i.e., particle shape, particle volume fraction, and particle distribution), and used to examine the effects of hot rolling on the microstructure evolution. In this study, microstructures after ~80% hot rolling were used as the initial microstructures for the subsequent cold rolling simulation. Plane-strain compression loading was employed in the FE models to simulate cold rolling with reductions from ~80% to ~94%. Stringer analyses with the consideration of particle fracture were then performed with the simulated cold rolling results. The results of void evolution analyses show that microstructures with elliptical particles incorporate a much larger (almost double) void volume fraction than those with circular particles, indicating that the elliptical particles are fractured more easily than the circular ones. The results from the fracture mode analyses show that, under the adopted simple compression loading assumption, almost all the particles (i.e., >99%) were fractured by tensile separation. The results of stringer analyses show that, during cold rolling, the stringer volume fractions increase substantially due to the particle fracture, especially for the microstructures with the elliptical particles, and that the stringer volume fractions from stringers comprising many particles tend to increase faster. The maximum stringer lengths for the microstructures with circular particles tend to remain constant or decrease during cold rolling, whereas those for elliptical particles tend to slightly increase after a slight decrease. The number of particles at the surface increases very rapidly due to particle fracture during cold rolling.

36 MATERIALS SCIENCE↗

Systems design and analysis of the microwave radiometer spacecraft

Systems design and analysis data were generated for microwave radiometer spacecraft concept using the Large Advanced Space Systems (LASS) computer aided design and analysis program. Parametric analyses were conducted for perturbations off the nominal-orbital-altitude/antenna-reflector-size and for control/propulsion system options. Optimized spacecraft mass, structural element design, and on-orbit loading data are presented. Propulsion and rigid-body control systems sensitivities to current and advanced technology are established. Spacecraft-induced and environmental effects on antenna performance (surface accuracy, defocus, and boresight off-set) are quantified and structured material frequencies and modal shapes are defined.

Garrett, L. B.↗

Epitaxial growth of Hg/1-x/Cd/x/Te by chemical vapor transport

The chemical vapor transport technique was applied for the first time to the growth of Hg(1-x)Cd(x)Te epitaxial layers on CdTe substrates using a preannealed source material of Hg(0.8)Cd(0.2)Te. The experiment took place in a pretreated ampoule loaded with source material, HgI2 transport agent, and substrate and sealed under a residual pressure of about 10 to the -5th torr. The temperature of the source region was 590 C and that of the deposition zone 535 C with a nearly sigmoidal shaped profile between the end temperatures. The change in appearance of the substrate surface during the experiment is described, and the structures of the surface of the Hg(1-x)Cd(x)Te layer and of the layer itself as revealed by Nomarski contrast illumination and Laue X-ray diffraction, respectively, are discussed.

Wiedemeier, H.↗

Damage Tolerance Testing of a NASA TransHab Derivative Woven Inflatable Module

Current options for Lunar habitat architecture include inflatable habitats and airlocks. Inflatable structures can have mass and volume advantages over conventional structures. However, inflatable structures carry different inherent risks and are at a lower Technical Readiness Level (TRL) than more conventional metallic structures. One of the risks associated with inflatable structures is in understanding the tolerance to induced damage. The Damage Tolerance Test (DTT) is designed to study the structural integrity of an expandable structure. TransHab (Figure 1) was an experimental inflatable module developed at the NASA/Johnson Space Center in the 1990 s. The TransHab design was originally envisioned for use in Mars Transits but was also studied as a potential habitat for the International Space Station (ISS). The design of the TransHab module was based on a woven design using an Aramid fabric. Testing of this design demonstrated a high level of predictability and repeatability with analytical predictions of stresses and deflections. Based on JSC s experience with the design and analysis of woven inflatable structures, the Damage Tolerance Test article was designed and fabricated using a woven design. The DTT article was inflated to 45 psig, representing 25% of the ultimate burst pressure, and one of the one-inch wide longitudinal structural members was severed by initiating a Linear Shaped Charge (LSC). Strain gage measurements, at the interface between the expandable elements (straps) and the nonexpandable metallic elements for pre-selected longitudinal straps, were taken throughout pressurization of the module and strap separation. Strain gage measurements show no change in longitudinal strap loading at the bulkhead interface after strap separation indicating loads in the restraint layer were re-distributed local to the damaged area due to the effects of friction under high internal pressure loading. The test completed all primary objectives with better than expected results. This paper will discuss space inflatable structures, damage tolerance analysis, test results, and applicability to the Lunar architecture.

Edgecombe, John↗

Seating Considerations for Spaceflight: The Human to Machine Interface

Seating is one of the most critical components to be considered during design of a spacecraft. Since seats are the final interface between the occupant and the vehicle wherein all launch and landing operations are performed, significant effort must be spent to ensure proper integration of the human to the spacecraft. The importance of seating can be divided into two categories: seat layout and seat design. The layout of the seats drives the overall cabin configuration - from displays and controls, to windows, to stowage, to egress paths. Since the layout of the seats is such a critical design parameter within the crew compartment, it is one of the first design challenges that must be completed in the critical path of the spacecraft design. In consideration of seat layout in the vehicle, it is important for the designers to account for often intangible factors such as safety, operability, contingency performance, crew rescue. Seat layout will lead to definition of the quantity, shape, and posture of the seats. The seats of the craft must restrain and protect the occupant in all seated phases of flight, while allowing for nominal mission performance. In design of a spacecraft seat, the general posture of the occupant and the landing loads to be encountered are the greatest drivers of overall design. Variances, such as upright versus recumbent postures will dictate fit of the seat to the occupant and drive the total envelope of the seat around the occupant. Seat design revolves around applying sound principles of seated occupant protection coupled with the unique environments driven by the seat layout, landing loads, and operational and emergency scenarios.

Gohmert, Dustin M.↗

Model Validation of an RSRM Transporter Through Full-scale Operational and Modal Testing

The Reusable Solid Rocket Motor (RSRM) segments, which are part of the current Space Shuttle system and will provide the first stage of the Ares launch vehicle, must be transported from their manufacturing facility in Promontory, Utah, to a railhead in Corinne, Utah. This approximately 25-mile trip on secondary paved roads is accomplished using a special transporter system which lifts and conveys each individual segment. ATK Launch Systems (ATK) has recently obtained a new set of these transporters from Scheuerle, a company in Germany. The transporter is a 96-wheel, dual tractor vehicle that supports the payload via a hydraulic suspension. Since this system is a different design than was previously used, computer modeling with validation via test is required to ensure that the environment to which the segment is exposed is not too severe for this space-critical hardware. Accurate prediction of the loads imparted to the rocket motor is essential in order to prevent damage to the segment. To develop and validate a finite element model capable of such accurate predictions, ATA Engineering, Inc., teamed with ATK to perform a modal survey of the transport system, including a forward RSRM segment. A set of electrodynamic shakers was placed around the transporter at locations capable of exciting the transporter vehicle dynamics. Forces from the shakers with varying phase combinations were applied using sinusoidal sweep excitation. The relative phase of the shaker forcing functions was adjusted to match the shape characteristics of each of several target modes, thereby customizing each sweep run for exciting a particular mode. The resulting frequency response functions (FRF) from this series of sine sweeps allowed identification of all target modes and other higher-order modes, allowing good comparison to the finite element model. Furthermore, the survey-derived modal frequencies were correlated with peak frequencies observed during road-going operating tests. This correlation enabled verification of the most significant modes contributing to real-world loading of the motor segment under transport. After traditional model updating, dynamic simulation of the transportation environment was compared to the measured operating data to provided further validation of the analysis model. KEYWORDS Validation, correlation, modal test, rocket motor, transporter

Brillhart, Ralph↗

Field Test Report Neutron Scintillator Array Dry Storage Cask Scanner FY2024

During two weeks of Field Testing at the Idaho National Laboratory INTEC Cask Farm in July and August 2024, the LLNL Dry Storage Cask Scanner Array was lifted on top of an MC-10 dry storage fuel cask and operated to acquire neutron and gamma-ray data from the 24 fuel bundle positions. Neutron and gamma-ray data acquisition scans across the top of the cask of varying dwell times were performed July 15-18, 2024 and August 19-22, 2024 to evaluate the ability of the scanner data to reveal asymmetries in the fuel positions that reflect asymmetries in the MC-10 cask fuel bundle loading. The MC-10 cask 24 position fuel bundle loading at the INTEC Cask Farm is well documented, including the locations of six empty fuel bundle positions. This loading presents an opportunity to test the ability of the scanner system to detect diversion of spent fuel bundles as well as to validate the MC-10 cask MCNP modeling. The cask scanner array consists of six Stilbene crystal scintillator detectors and a linear actuator frame that moves the six detectors across the MC-10 dry storage cask to obtain data above each of the 24 fuel bundle positions. The detectors are connected to a pulse-shape discrimination data acquisition system capable of generating separate neutron and gamma-ray spectra for each detector and for each scan position. From the prior single detector Field Test in 2021 and iteration with MCNP modeling, the neutron and gamma-ray data were analyzed in multiple energy regions to identify an analysis method that would provide the strongest and most consistent signature of the asymmetric MC-10 cask fuel loading1 . From both the 2021 Field Test and the current Field Test results, the neutron capture gamma-ray count rate around 2.2 MeV provides the strongest signature of the asymmetric MC-10 cask fuel loading and has qualitative agreement with MCNP calculations. Counting all gamma-rays produces a similar signature. Neutrons emerging from the cask top are moderated and captured by the hydrogen in the polyethylene moderator and scintillator detector, producing a 2.2 MeV gamma ray which is seen in the scintillator gamma-ray spectrum. The count rate in the 2.2 MeV gamma-ray region is ~50 c/s, which is ~1000x higher than the ~0.05 n/s rate in the > 4MeV neutron region, and ~50x greater than the ~1 n/s rate in the neutrons > 500 keV region. Analysis of the 2.2 MeV neutron-capture Compton-scattered gamma-rays produces a statistically significant signature of the INTEC Cask Farm MC-10 asymmetric fuel loading. MCNP simulations indicate that the average neutron energy spectrum offers the potential to detect a large asymmetry from several missing bundles as well as individual missing fuel bundles. Testing this feature will require measurements on a cask with single missing elements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Panel resonant behavior of wind turbine blades.

The principal design drivers in the certification of wind turbine blades are ultimate strength, fatigue resistance, adequate tip-tower clearance, and buckling resistance. Buckling resistance is typically strongly correlated to both ultimate strength and fatigue resistance. A composite shell with spar caps forms the airfoil shape of a blade and reinforcing shear webs are placed inside the blade to stiffen the blade in the flap-wise direction. The spar caps are dimensioned and the shear webs are placed so as to add stiffness to unsupported panel regions and reduce their length. The panels are not the major flap-wise load carrying element of a blade; however, they must be designed carefully to avoid buckling while minimizing blade weight. Typically, buckling resistance is evaluated by consideration of the load-deflection behavior of a blade using finite element analysis (FEA) or full-scale static testing of blades under a simulated extreme loading condition. The focus of this paper is on the use of experimental modal analysis to measure localized resonances of the blade panels. It can be shown that the resonant behavior of these panels can also provide a means to evaluate buckling resistance by means of analytical or experimental modal analysis. Further, panel resonances have use in structural health monitoring by observing changes in modal parameters associated with panel resonances, and use in improving panel laminate model parameters by correlation with test data. In recent modal testing of wind turbine blades, a set of panel modes were measured. This paper will report on the findings of these tests and accompanying numerical and analytical modeling efforts aimed at investigating the potential uses of panel resonances for blade evaluation, health monitoring, and design.

17 WIND ENERGY↗

Shaping Transistor Leads for Better Solder Joints

Special lead-forming tool puts step in leads of microwave power transistors without damaging braze joints that fasten leads to package. Stepped leads are soldered to circuit boards more reliably than straight leads, and stress on brazes is relieved. Lead-forming hand-tool has two parts: a forming die and an actuator. Spring-loaded saddle is adjusted so that when transistor package is placed on it, leads rest on forming rails.

Mandel, H.↗

Experimental Tests of a Real Building Seismically Retrofitted by Special Buckling-Restrained Braces

Buckling Restrained Braces (BRBs), differently from conventional braces, do not exhibit appreciable difference between the tensile and compression capacity and no strength degradation of brace capacity under compressive and cyclic loading. Since lateral and local buckling behaviour modes are restrained, large inelastic capacities are attainable. Hence, BRBs may represent an efficient and reliable solution for reducing the seismic vulnerability of buildings. Results of experimental tests on the response of a real two-story reinforced concrete (RC) building equipped with BRBs are presented and discussed. The considered BRBs are a special 'only-steel' version of the more common 'unbonded braces'. In particular, two different BRBs have been tested. Both of them are detachable 'only-steel' devices, consisting in a rectangular steel plate and a restraining steel sleeve. The latter is composed by two omega shapes which are bolted together. The main characteristic of the braces consists in the possibility to hide them within the space between the facing and the backing of masonry infill walls commonly used for RC buildings.

58 GEOSCIENCES↗

Reconfigurable metamaterial absorber as an optical switch based on organic-graphene control

In this paper, we have suggested an effective optical switch with the cross fractal shape. It contains the main cross element that connected to four parasitic elements by four organic’s material junctions. This absorber is modified as a tunable element by using the graphene layer which can be considered for compensating the physical distortion. Each organic and parasitic load is placed over a graphene layer. These graphene layers separated with a SiO{sub 2} thin film. We have implemented a SiO{sub 2} layer as a spacer between the graphene and metal ground layer. The organic materials are popular for their various resistances value. We have applied a bulky dielectric slab with two different conductivity values for high and low resistance (HRS and LRS). This absorber works at the range of 90–100 THz for mid-infrared spectrum and the bandwidth of 4%. In the HRS mode the reflection value is about − 35 up to − 25 dB. When the organic material switched to LRS mode, this value drastically increased to − 5 dB. The designed absorber has both the tunable and switchable attributes. We have simulated this switch by the finite integral technique method with CST microwave studio.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Interlayer reinforcement of 3D printed concrete by the in-process deposition of U-nails

Highlights: • An in-process interlayer reinforcement approach for 3D concrete printing was proposed through the concurrent deposition of U-nails. • Significant strength and toughness improvement was achieved for U-nail reinforced 3D-printed concrete. • The bridge linking effect and dowel action of U-nails were analysed. • Response surface method were utilised to quantify the effects of U-nails on the interlayer bonding behaviour. 3D concrete printing has tremendous potential for construction manufacturing; however, weak interface bonding between adjacent layers remains a well-known issue that affects the mechanical properties of printed structures. The layers introduce anisotropy and reduce the capacity to resist tensile and shear loads. Reinforcements, inserted perpendicular to the printed layers to traverse the interfaces, can improve these limitations, but the insertion of reinforcements is difficult to achieve in practice, and there are few published studies exploring appropriate methods. This study presents a promising approach using U-shaped nails inserted into concrete during the printing process. The bridging effect and dowel action of the applied U-nails are visualised and analysed to elucidate the toughness improvement. The ultimate tensile strength and shear strength of 3D printed concrete are significantly increased by 145.0% and 220.0%, respectively. U-nails with a filament thickness of 2–2.5 mm are recommended to yield optimal improvement in the interlayer strength.

36 MATERIALS SCIENCE↗

Fractal breakage of porous carbonate sand particles: Microstructures and mechanisms

In situ, three-dimensional (3D) characterizations of particle breakage in porous carbonate sands are presented, for the first time, with synchrotron-based micro computed tomography. Evolution of grain-scale characteristics are identified and quantified via elaborate image processing and topology analyses. The sequential 3D images reveal distinctly different fracture mechanisms for carbonate sands from silica sands. The angular shape of carbonate sand particles facilitates bending fracture, and particles with a lower sphericity and a higher porosity are more prone to break. 3D crack networks extracted from fractured particles imply considerable cleavage along initial pores. The fractal dimension of crack networks increases with external loading due to crack branching via cleavage. The resultant fragment size distribution also appears fractal and the fractal feature is valid down to the breakage limit of calcium carbonate. Crack propagation along the initial pores reduces the energy barrier for particle breakage and thus fracture strength of particles

Carbonate sands↗

Muon RLA - design status and simulations

The Neutrino Factory baseline design involves a complex chain of accelerators beginning with a linac. This first pre-linac follows the capture and bunching section and accelerates the muons from about 244 to 900 MeV and must accept a high emittance beam about 30 cm wide with a 10% energy spread. It uses counterwound, shielded superconducting solenoids and 201 MHz superconducting cavities, and currently consists of 24 3 m and 24 5 m long cryomodules. The next stage is a 1st dogbone-shaped RLA that takes the total energy from 900 MeV to 3.6 GeV in 4.5 passes, followed by a 2nd RLA that takes the energy from 3.6 to 12.6 GeV in 4.5 passes. Simulations are in progress to optimize the optics and determine the radiation loads from beam loss and muon decay.

43 PARTICLE ACCELERATORS↗

Stochastic Particle Real Time Analyzer (SPARTA) Validation and Verification Suite

This report presents the test cases used to verify, validate and demonstrate the features and capabilities of the first release of the 3D Direct Simulation Monte Carlo (DSMC) code SPARTA (Stochastic Real Time Particle Analyzer). The test cases included in this report exercise the most critical capabilities of the code like the accurate representation of physical phenomena (molecular advection and collisions, energy conservation, etc.) and implementation of numerical methods (grid adaptation, load balancing, etc.). Several test cases of simple flow examples are shown to demonstrate that the code can reproduce phenomena predicted by analytical solutions and theory. A number of additional test cases are presented to illustrate the ability of SPARTA to model flow around complicated shapes. In these cases, the results are compared to other well-established codes or theoretical predictions. This compilation of test cases is not exhaustive, and it is anticipated that more cases will be added in the future.

97 MATHEMATICS AND COMPUTING↗