Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “limiting techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Measurement of surface flow velocity with ripplon scattering

It was shown that the light scattered from the ripplons on a moving liquid interface can be used to measure the velocity fields in the interface. The technique measures the true interface velocity. It is, however, limited to the measurement of relatively fast moving interfaces because the scattered irradiance is large only in a very small angular range about the specularly reflected beam, and the concerted influence of instrumental and natural braodening of the power spectrum leads to severely overlapping doublet for low velocity fields.

Sirohi, R. S.↗
NASA NTRS1981

Position surveillance using one active ranging satellite and time-of-arrival of a signal from an independent satellite

A satellite-aided mobile communication service was tested for position surveillance, with an automatic responder circuit connected between the vehicle receiver and transmitter, and a receiver coded for signals from another satellite. Using the ATS-6 and GOES satellites, a tone-code ranging transponder was connected between the receiver and transmitter, and a 468 MHz receiver was connected to the responder unit for passive reception of the 100 bit per second timing and data signal. Results showed lines of position derived from the active ranging through ATS-6 to be accurate to approximately 0.1 nautical mile, while the NOAA-GOES signals were accurate to about 1.6 miles. The active ranging bandwidth was 2.44 kHz, and the integration time was 0.1 second, while the limitation on accuracy was the 100 Hz bandwidth. This technique of position surveillance was concluded to be feasible and simple to operate, providing needed, good quality communications to the inland waterways industry.

Anderson, R. E.↗
NASA NTRS1980

A comparison between an empirical technique for the prediction of cyclogenesis and the LFM II

Preliminary empirical results are given of a study to determine the present-day utility of the George (1960) technique for predicting cyclogenesis. Surface and constant pressure charts are examined to determine the frequency and preferred locations for the occurrence of cold air injections. The accuracy of the empirical technique and the LFM II are compared for a limited number of cases. No consistent relationship between cold air injections and other atmospheric features is found. After the appearance of a cold air injection, cyclogenesis, a center jump, or a deepening of an existing cyclone occurs 77% of the time.

Atlas, R.↗
NASA NTRS1983

An efficient algorithm for generating random number pairs drawn from a bivariate normal distribution

An efficient algorithm for generating random number pairs from a bivariate normal distribution was developed. Any desired value of the two means, two standard deviations, and correlation coefficient can be selected. Theoretically the technique is exact and in practice its accuracy is limited only by the quality of the uniform distribution random number generator, inaccuracies in computer function evaluation, and arithmetic. A FORTRAN routine was written to check the algorithm and good accuracy was obtained. Some small errors in the correlation coefficient were observed to vary in a surprisingly regular manner. A simple model was developed which explained the qualities aspects of the errors.

Campbell, C. W.↗
NASA NTRS1982

Material characterization and specification development for 350 F curing epoxy-graphite materials

New analytical techniques and a processability laminate have been used in the development of a material specification for 350 F curing epoxy-graphite materials. The development of the specification required the evaluation of prepregs which had variations in their processing behavior that were detected only in production. Chemical techniques were used to analyze the prepregs and establish limits on the concentrations of the various chemical constituents. A batch acceptance test laminate was designed to determine suitability of prepregs for production useage. The new specification requires that the processability laminate be ultrasonically and micrographically inspected for voids and porosity. Incorporation of these and other requirements will help to insure material consistency and processability.

Rogers, A. K.↗
NASA NTRS1984

Airborne laser topographic mapping results

The results of terrain mapping experiments utilizing the National Aeronautics and Space Administration (NASA) Airborne Oceanographic Lidar (AOL) over forested areas are presented. The flight tests were conducted as part of a joint NASA/U.S. Army Corps of Engineers (CE) investigation aimed at evaluating the potential of an airborne laser ranging system to provide cross-sectional topographic data on flood plains that are difficult and expensive to survey using conventional techniques. The data described in this paper were obtained in the Wolf River Basin located near Memphis, TN. Results from surveys conducted under winter 'leaves off' and summer 'leaves on' conditions, aspects of day and night operation, and data obtained from decidous and coniferous tree types are compared. Data processing techniques are reviewed. Conclusions relative to accuracy and present limitations of the AOL, and airborne lidar systems in general, to terrain mapping over forested areas are discussed.

Krabill, W. B.↗
NASA NTRS1985

An evaluation and comparison of vertical profile data from the VISSR Atmospheric Sounder (VAS)

A statistical evaluation is used to compared vertical profiles of temperature and moisture derived from VISSR Atmospheric Sounder (VAS) with three different algorithms to that of corresponding rawinsonde measurements for a clear cold environment. To account for time and space discrepancies between the data sets, rawinsonde data were adjusted to be representative of the satellite sounding times. Both rawinsonde and satellite sounding data were objectively analyzed onto a mesoscale grid. These grid point values were compared at 50 mb pressure increments from the surface up to 100 mb. The data were analyed for horizontal and vertical structure, representatives of derived parameters, and significant departure (improvement) from the apriori (first guess) information. Results indicate some rather strong temperature and moisture biases exist in the satellite soundings. Temperature biases of 1 to 4 C and dewpoint biases of 2 to 6 C generally occur in layers where strong inversions are present and vary with time as these atmospheric features evolve. The biases also changes as a function retrieval scheme suggesting limitations and restrictions on the applications of the various techniques. Standard temperature deviations range from 1 to 2 C for each retrieval scheme with maximum values around 800 and 400 mb. Derived parameters (precipitable water and thickness) suffer from similar biases, though to a somewhat lesser extent. Gradients of basic and derived parameters are generally weaker but have good horizontal structure where magnitudes of the parameters are relatively strong. Integrated thermal (temperature) and moisture (precipitable water) parameters show mixed results.

Jedlovec, G. J.↗
NASA NTRS1983

Xe-129 - Xe-128 and Ar-40 - Ar-39 chronology of two Antarctic enstatite meteorites

Xe-129 - Xe-128 and Ar-40 - Ar-39 analyses has been performed on two Antarctic enstatite meteorites, the chondrite Y-691 and the aubrite (enstatite achondrite) ALH-78113. Both meteorites have complex Ar-40 - Ar-39 release patterns to which no unambiguous age assignment is possible. Both give apparently satisfactory Xe-129 - Xe-128 correlations corresponding to unusual ages. The I-Xe age of the chondrite Y-691 is 16 Ma after Bjurbole, not unusual for chondrites in general but 10 Ma later than previously known ages for enstatite chondrites. The I-Xe age of the aubrite ALH-78113 is 210 Ma after Bjurbole, the latest age (rather than a limit) so far observed by the I-Xe technique, but this age assignment must be considered tentative because of the possibility that it is significantly influenced by terrestrial I contamination.

Honda, M.↗
NASA NTRS1985

NASA/JPL Aircraft SAR Workshop Proceedings

Speaker-supplied summaries of the talks given at the NASA/JPL Aircraft SAR Workshop on February 4 and 5, 1985, are provided. These talks dealt mostly with composite quadpolarization imagery from a geologic or ecologic prespective. An overview and summary of the system characteristics of the L-band synthetic aperture radar (SAR) flown on the NASA CV-990 aircraft are included as supplementary information. Other topics ranging from phase imagery and interferometric techniques classifications of specific areas, and the potentials and limitations of SAR imagery in various applications are discussed.

Donovan, N.↗
NASA NTRS1985

An evaluation and comparison of vertical profile data from the VISSR Atmospheric Sounder (VAS)

A statistical evaluation is used to compared vertical profiles of temperature and moisture derived from VISSR Atmospheric Sounder (VAS) with three different algorithms to that of corresponding rawinsonde measurements for a clear cold environment. To account for time and space discrepancies between the data sets, rawinsonde data were adjusted to be representative of the satellite sounding times. Both rawinsonde and satellite sounding data were objectively analyzed onto a mesoscale grid. These grid point values were compared at 50 mb pressure increments from the surface up to 100 mb. The data were analyzed for horizontal and vertical structure, representatives of derived parameters, and significant departure (improvement) from the apriori (first guess) information. Results indicate some rather strong temperature and moisture biases exist in the satellite soundings. Temperature biases of 1 to 4 C and dewpoint biases of 2 to 6 C generally occur in layers where strong inversions are present and vary with time as these atmospheric features evolve. The biases also changes as a function retrieval scheme suggesting limitations and restrictions on the applications of the various techniques. Standard temperature deviations range from 1 to 2 C for each retrieval scheme with maximum values around 800 and 400 mb. Derived parameters (precipitable water and thickness) suffer from similar biases, though to a somewhat lesser extent. Gradients of basic and derived parameters are generally weaker but have good horizontal structure where magnitudes of the parameters are relatively strong. Integrated thermal (temperature) and moisture (precipitable water) parameters show mixed results.

Jedlovec, G. J.↗
NASA NTRS1987

Double-Referenced, Pulsed, Phase-Locked Loop - DRP2L2

System allows precise measurement of phase shift between two toneburst signals initially derived from same periodic source but delayed by different amounts through either path-length differences, propagation velocity differences, or both. Used to measure accurately phase shift encountered by acoustic wave striking front and back surfaces of sample. Velocity known, resulting measurement is of sample thickness. Thickness known, measurement is of sound velocity. Technique applies to many sources of radiation and not limited to acoustics.

Heyman, J. S.↗
NASA NTRS1986

Two-photon laser-induced fluorescence detection of OH

The TP-LIF OH sensor is based on the principle that a molecule having multiple energy states, all of which are bonding, can be pumped into the highest state with the resulting fluorescence being blue-shifted relative to all pumping wavelengths. In this way, one can successfully discriminate against virtually all noise sources in the system using long wavelength blocking filters in conjunction with solar-blind photomultiplier tubes. Thus, these systems tend to be signal limited rather than signal-to-noise limited as is true of the SP-LIF technique as well as other conventional analytical methods. The trick to achieving the above sampling scheme, with high efficiency, is in the use of high photon fluxes of short time duration. Obviously, the latter type of light source is fulfilled nicely by available pulsed lasers. From an operational point of view, however, this laser source needs to be tunable. The latter characteristic permits extremely high selectivity for the detection of a diatomic or simple polyatomic molecule by taking advantage of the high-resolution spectroscopic features of these type species.

Davis, D. D.↗
NASA NTRS1987

Hydrogen oxidation mechanism with applications to (1) the chaperon efficiency of carbon dioxide and (2) vitiated air testing

Ignition delay times for the hydrogen/oxygen/carbon dioxide/argon system were obtained behind reflected shock waves. A detailed kinetic mechanism modeled the experimental hydrogen/oxygen data, Skinner and Ringrose's high-pressure data, and Slack and Grillo's hydrogen/air data. A carbon dioxide chaperon efficiency of 7.0 +/- 0.2 was determined. The reaction pathway H2O yields H2O2 yields OH yields H was required to model the high-pressure data. It is suggested that some of the lowest temperature data points (1.0 and 0.5 atm) for Slack and Grillo's hydrogen/air experiments are in error. It was found that the technique of simplifying a detailed kinetic mechanism for a limited range of experimental data may render the model useless for other test conditions.

Brabbs, Theodore A.↗
NASA NTRS1986

The pultrusion process for structures on advanced aerospace transportation systems

The pultrusion process, which has the potential for use in the manufacture of structures for aerospace hardware, is described. In this process, reinforcing fibers are pulled continuously through a resin system for wetting and subsequently through a heated die for polymerization. By using this process, fabrication of very long lengths of high strength, lightweight structures with consistently high quality for aerospace applications is possible. The more conventional processes involve hand lay-up, vacuum bagging, autoclaving or oven curing techniques such that lengths of structural elements produced are limited by the lengths of autoclaves or curing ovens. Several types of developmental structural elements are described in which fiberglass, aramid, graphite, and hybrid fiber systems have been used as reinforcements in an epoxy matrix and their flexural properties compared. Reinforcement fibers having tailor-made orientations which achieve tailor-made strength in the pultrusions are described. The potential aerospace applications for the pultruded products are described with advantages cited over conventional hand lay-up methods.

Wilson, Maywood L.↗
NASA NTRS1987

Optical tracking using charge-coupled devices

The extraction of precise positional information from CCD images of point-source and extended optical targets is considered, and three examples of CCD optical trackers for space-based operation are described. For ideal point sources, a centerfinding accuracy of 1/100 pixel and a measuremet jitter of less than 1/250 pixel have been obtained using thinned, backside-illuminated devices. Tracker accuracy is shown to be limited by small variation in the optical image shape. Techniques for tracking, and methods for searching the entire field for the desired targets, are also discussed.

Stanton, Richard H.↗
NASA NTRS1988

Gas permeation measurements on small polymer specimens

Mass spectrometry was used to measure oxygen and nitrogen permeabilities while polarography was used to measure oxygen permeabilities for several contact lens materials. Applicable sample holders were designed and fabricated to accommodate curved and flat specimens. A prepared standard was used to calibrate the mass spectrometric analyses. The oxygen permeability values determined by mass spectrometry were significantly greater than those determined by polarography. This was attributed to the phase boundary phenomena and the limiting oxygen permeance of water inherent in the polarographic technique. Polarographic values determined were in good agreement with proprietary values obtained by polarography, with the exception of one material.

Burns, Karen S.↗
NASA NTRS1987

Constraint-based stereo matching

The major difficulty in stereo vision is the correspondence problem that requires matching features in two stereo images. Researchers describe a constraint-based stereo matching technique using local geometric constraints among edge segments to limit the search space and to resolve matching ambiguity. Edge segments are used as image features for stereo matching. Epipolar constraint and individual edge properties are used to determine possible initial matches between edge segments in a stereo image pair. Local edge geometric attributes such as continuity, junction structure, and edge neighborhood relations are used as constraints to guide the stereo matching process. The result is a locally consistent set of edge segment correspondences between stereo images. These locally consistent matches are used to generate higher-level hypotheses on extended edge segments and junctions to form more global contexts to achieve global consistency.

Kuan, D. T.↗
NASA NTRS1991

Nonlinear compensation techniques for magnetic suspension systems

In aerospace applications, magnetic suspension systems may be required to operate over large variations in air-gap. Thus the nonlinearities inherent in most types of suspensions have a significant effect. Specifically, large variations in operating point may make it difficult to design a linear controller which gives satisfactory stability and performance over a large range of operating points. One way to address this problem is through the use of nonlinear compensation techniques such as feedback linearization. Nonlinear compensators have received limited attention in the magnetic suspension literature. In recent years, progress has been made in the theory of nonlinear control systems, and in the sub-area of feedback linearization. The idea is demonstrated of feedback linearization using a second order suspension system. In the context of the second order suspension, sampling rate issues in the implementation of feedback linearization are examined through simulation.

Trumper, David L.↗