Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interfacial energy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Electrolyzer Performance Loss from Accelerated Stress Tests and Corresponding Changes to Catalyst Layers and Interfaces

Stress tests are developed for proton exchange membrane electrolyzers that utilize low catalyst loading, elevated potential, and frequent cycling with square- and triangle-waves to accelerate anode catalyst layer degradation during intermittent operation. Kinetics drive performance losses (ohmic/transport secondary) and are accompanied by decreasing exchange current density, decreasing cyclic voltammetric capacitance, and increasing polarization resistance. Decreased kinetics are likely due to a combination of iridium (Ir) migration into electrochemically inaccessible locations in the anode or membrane, Ir particle growth (supported by X-ray scattering), changes in the extent of the Ir oxidation state (supported by X-ray absorption spectroscopy), and anode catalyst layer reordering. Decreasing catalyst/transport layer contact and catalyst/membrane interfacial tearing may add contact resistances and account for increasing ohmic losses. Performance losses for low and moderate catalyst loading, as well as from accelerated and model wind/solar cycling protocols, were likewise dominated by kinetics but vary in severity. Additionally, accelerated cycling (1 cycle per minute) appears to reasonably accelerate relevant loss mechanisms and can be used to project electrolyzer lifetime from anode deterioration. Ongoing accelerated stress test development and studies into performance loss mechanisms will continue to be critical as electrolysis shifts to intermittent power and low-cost applications.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Aqueous solvation of the chloride ion revisited with density functional theory: impact of correlation and exchange approximations

The specificity of aqueous halide solvation is fundamental to a wide range of bulk and interfacial phenomena spanning from biology to materials science. Halide polarizability is thought to drive the ion specificity, and if so, it is essential to have an accurate description of the electronic properties of halide ions in water. To this end, the solvation of the chloride anion, Cl - has been reinvestigated with state-of-the-art density functional theory. Specifically, the PBE-D3, PBE0-D3, and SCAN functionals have been employed to probe the impact of correlation and exchange approximations. Anticipating the findings, adding exact exchange improves the electronic structure, but simultaneously significantly reduces the Cl - polarizability, resulting in an over-structured Cl–O radial distribution function (RDF) and longer water H-bond lifetimes to Cl - . SCAN does not yield as much improvement in the energetics of Cl - relative to bulk water, but does result in a smaller reduction of the polarizability and thus a less structured Cl–O RDF, which agrees better with experiment. Special consideration is therefore warranted in assessing the impact of exchange on the energy, charge density, and the charge density response when designing and testing hybrid functionals for aqueous halide solvation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Implementation of a Drift-Flux Model in SAM for Modeling of Passively Transported GAS in Molten Salt Reactors

The Nuclear Energy Advanced Modeling and Simulation (NEAMS) program is further developing the Multiphysics Object Oriented Simulation Environment (MOOSE) system thermal hydraulics (T/H) code, System Analysis Module (SAM), to include modeling of molten salt reactor (MSR) designs. MSR designs in which the fuel is dissolved in the salt coolant poses unique modeling and simulation (M&S) challenges because fission products—some of which will be noncondensable gasses—travel with the coolant, thus allowing for deposition and interaction throughout the entire system flow loop. This behavior must be modeled to successfully understand MSR system behavior during normal and off-normal operation events. In past work, SAM has been extended to include a passive species transport capability for modeling of MSR fission products that travel with the salt coolant. This work extends the model to include a drift-flux model to capture the tendency of the gas phase to move at a different velocity than the bulk liquid. Additional constitutive models have also been added for calculation of gas volume fraction, bubble radius, and interfacial area, which will be important for calculation of species phase migration in future coupling activities. Testing has been performed to ensure that the new model agrees with expected values for several simple models, but additional future work will be required to test the model for more complex geometries that will be needed for full-scale MSR simulations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2026

An Organic Carboxylate Host for Stable Sodium Metal Batteries

Sodium metal batteries (SMBs) hold great promise for the development of high-energy, sustainable energy storage solutions, but their practical deployment is hampered by unstable solid electrolyte interphases, uncontrollable sodium dendrite growth, and low Coulombic efficiency (CE) during repeated Na plating/stripping cycles. To address these challenges, we introduce an organic interlayer, containing perylenetetracarboxylic dianhydride sodium salt (Na4PT), on the surface of Cu current collector. This interlayer forms a sodiophilic organic interphase that lowers the nucleation barriers for sodium deposition and guides the formation of the interphase through polar carbonyl/carboxylate sites and a π-conjugated organic framework. A dendrite-free sodium metal anode is achieved using Na4PT coated Cu current collector. Under capacity-limited Na plating/stripping, Na||Na4PT@Cu half-cells deliver reversible capacities of 500 and 1,000 mAh g−1 at 0.1 and 1 A g−1 for 500 cycles with average CE above 99%. Post-cycling scanning electron microscopy and X-ray photoelectron spectroscopy measurements confirm that Na4PT@Cu promotes compact and uniform Na deposits and supports the formation of a stable interphase with reduced parasitic decomposition, directly correlating interfacial chemistry/morphology with high plating/stripping reversibility. These results highlight organic carboxylate coating as a practical interface engineering strategy for dendrite-free SMBs.

Chen, Chengxiang [University of Miami]↗
DOE OSTI2021

In Situ ATR-FTIR Study of the Cathode–Electrolyte Interphase: Electrolyte Solution Structure, Transition Metal Redox, and Surface Layer Evolution

We present a study of the lithium nickel manganese cobalt oxide (LiNi 0.6 Mn 0.2 Co 0.2 O 2 , NMC622) cathode-electrolyte interphase (CEI) during galvanostatic charging and discharging using in situ attenuated total reflectance Fourier transform infrared (ATR-FTIR) methods to investigate the voltage dependent electrolyte solution structure changes at the interface, transition metal (TM) redox chemistry, and cathode/electrolyte interfacial layer evolution. Furthermore, our in situ cell design provides both reliable electrochemical device testing and strong FTIR vibrational absorption signals near the cathode surface. Specifically, advanced spectral analysis elucidates changes of near-surface Li+ ion (de)solvation by solvent molecules during galvanostatic cycling. Moreover, cathode metal-oxygen vibrational absorptions, sensitive to TM redox behaviors and subsequent local structural variations, were correlated to cathode de-lithiation (and lithiation) and electrolyte solution structure changes. In addition, we have detected the formation and evolution of a CEI surface layer on the NMC622 cathode that contributes to the cell's capacity fade.

25 ENERGY STORAGE↗
DOE OSTI2019

A Reactive Element Approach to Improve Fracture Healing in Metallic Systems

Self-healing materials demonstrate the ability to close fractures and regain mechanical integrity after a catastrophic failure. However, self-healing in metals can be inhibited by the natural tendency for technologically-relevant metallic systems to oxidize on the crack surface. This study seeks to provide a thermodynamically-based mechanism to enhance healing capability at a solid/liquid interface through alloys designed with a reactive element alloying addition possessing a lower free energy of oxide formation than the parent element. In this study, model Sb-Cu and Sb-Zn systems enable comparisons between mechanistic behaviors based only on thermodynamic reactivity. Mechanical and microstructural investigation demonstrated that the more reactive alloying addition resulted in more effective bonding through increasing bond area and load-bearing capacity of the system. The improved bonding was attributed to improved wetting and reduction of the passivating surface oxide across an interface. The work has potential to advance self-healing capabilities in metallic systems through more appropriate alloy selection to enable improved healing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Designing Anion-Exchange Ionomers with Oriented Nanoscale Phase Separation at a Silver Interface

We report performance of polymer electrolyte-based energy systems is significantly impacted by transport within the electrode catalyst layer, where ionomer thin films coat catalyst particles. Proton exchange ionomer thin films have been thoroughly characterized, but few studies have critically examined anion-exchange ionomer (AEI) thin films. Further, none have reported nanoscale phase separation for hydrocarbon AEIs, which is critical to mitigate transport resistances. In this work, a set of hydrocarbon-based AEIs with nanoscale phase separation are developed from tunable block copolymer systems composed of polyisoprene (PIp) and polychloromethylstyrene (PCMS). The effect of the PIp/PCMS ratio, architecture, and thickness on the thin-film morphology of the neutral block copolymer precursors on silicon and silver substrates is investigated using grazing-incidence small-angle X-ray scattering (GISAXS) and atomic force microscopy (AFM). AEIs are prepared by quaternizing with trimethylamine or methylpiperidine and their cation-dependent morphology is characterized at 60 °C and 95% RH. A perpendicularly aligned morphology is observed on silver, while no phase separation is observed on silicon, indicating that silver-polymer interfacial interactions drive phase separation. After quaternization, dipole-dipole interactions induce some disorder, but nanoscale phase separation is still maintained. GISAXS patterns are modeled using a Unified Fit approach to understand water uptake and swelling, and recommendations for AEI design are presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2001

Ultrasonic Resonance Spectroscopy of Composite Rings for Flywheel Rotors

Flywheel energy storage devices comprising multilayered composite rotor systems are being studied extensively for utilization in the International Space Station. These composite material systems were investigated with a recently developed ultrasonic resonance spectroscopy technique. The system employs a swept frequency approach and performs a fast Fourier transform on the frequency spectrum of the response signal. In addition. the system allows for equalization of the frequency spectrum, providing all frequencies with equal amounts of energy to excite higher order resonant harmonics. Interpretation of the second fast Fourier transform, along with equalization of the frequency spectrum, offers greater assurance in acquiring and analyzing the fundamental frequency, or spectrum resonance spacing. The range of frequencies swept in a pitch-catch mode was varied up to 8 MHz, depending on the material and geometry of the component. Single and multilayered material samples, with and without known defects, were evaluated to determine how the constituents of a composite material system affect the resonant frequency. Amplitude and frequency changes in the spectrum and spectrum resonance spacing domains were examined from ultrasonic responses of a flat composite coupon, thin composite rings, and thick composite rings. Also, the ultrasonic spectroscopy responses from areas with an intentional delamination and a foreign material insert, similar to defects that may occur during manufacturing malfunctions, were compared with those from defect-free areas in thin composite rings. A thick composite ring with varying thickness was tested to investigate the full-thickness resonant frequency and any possible bulk interfacial bond issues. Finally, the effect on the frequency response of naturally occurring single and clustered voids in a composite ring was established.

Harmon, Laura M.↗
NASA NTRS2004

Boiling Heat Transfer Mechanisms in Earth and Low Gravity: Boundary Condition and Heater Aspect Ratio Effects

Boiling is a complex phenomenon where hydrodynamics, heat transfer, mass transfer, and interfacial phenomena are tightly interwoven. An understanding of boiling and critical heat flux in microgravity environments is of importance to space based hardware and processes such as heat exchange, cryogenic fuel storage and transportation, electronic cooling, and material processing due to the large amounts of heat that can be removed with relatively little increase in temperature. Although research in this area has been performed in the past four decades, the mechanisms by which heat is removed from surfaces in microgravity are still unclear. Recently, time and space resolved heat transfer data were obtained in both earth and low gravity environments using an array of microheaters varying in size between 100 microns to 700 microns. These heaters were operated in both constant temperature as well as constant heat flux mode. Heat transfer under nucleating bubbles in earth gravity were directly measured using a microheater array with 100 m resolution operated in constant temperature mode with low and high subcooled bulk liquid along with images from below and from the side. The individual bubble departure diameter and energy transfer were larger with low subcooling but the departure frequency increased at high subcooling, resulting in higher overall heat transfer. The bubble growth for both subcoolings was primarily due to energy transfer from the superheated liquid layer relatively little was due to wall heat transfer during the bubble growth process. Oscillating bubbles and sliding bubbles were also observed in highly subcooled boiling. Transient conduction and/or microconvection was the dominant heat transfer mechanism in the above cases. A transient conduction model was developed and compared with the experimental data with good agreement. Data was also obtained with the heater array operated in a constant heat flux mode and measuring the temperature distribution across the array during boiling. The instantaneous heat transfer into the substrate was numerically determined and subtracted from the supplied heat to obtain the wall to liquid heat flux.

Kim, Jungho↗
DOE OSTI2022

Perspectives on Microfluidics for the Study of Asphaltenes in Upstream Hydrocarbon Production: A Minireview

The utilization of microfluidics has generated deep insights into asphaltene precipitation mechanisms and oil–water emulsion stabilization. Agglomeration and precipitation of asphaltenes can cause flow assurance problems during the extraction and transportation of crude oil. Change in temperature, pressure, reservoir conditions, and solvents can change the local environment, leading to asphaltene precipitation. Understanding asphaltene properties and precipitation pathways becomes critical in devising mitigation methods, demulsifiers, and suitable conditions during hydrocarbon processing. Microfluidics has helped in high throughput measurement studies, understanding critical processing conditions, fast demulsifier screening, and the effect of solvent concentration on deposition, generating useful information for utilization at the point of resource extraction facilitating improved resource management. It has become possible to capture the porous, complex nature of reservoir formations and the interaction of chemicals during precipitation through integrated analytics and visualization studies available only through microfluidics. The use of droplet microfluidics, with optical microscopy and high-speed imaging to study the oil–water interface, has resulted in greater understanding of the role of asphaltenes in interfacial properties and emulsion stabilization. Here, this minireview highlights the crucial aspects of microfluidics that have been used to understand physicochemical behavior and dynamics of asphaltene deposition. Some of the unique devices have been presented focusing on the key elements of microfluidics design, fabrication, and analysis, as the insight obtained from microfluidics strongly depends on the device design and the controllability of the experimental parameters. Successful implementation of microfluidics for efficient and controlled experiments, short analysis time scales and rapid screening, and generation of high-quality, reliable data that convey asphaltene deposition issues and interface behavior in emulsions shows the importance of microsystems for advancing knowledge in hydrocarbon production and processing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Harnessing the surface structure to enable high-performance cathode materials for lithium-ion batteries

The ever-increasing demand for high-performance batteries have been driving the fundamental understanding of the crystal/surface structural and electrochemical properties of intercalation cathode materials, among which the olivine-type, spinel and layered lithium transition metal oxide materials have received particular attention in the past decade due to their successful commercialization. While the most current studies focus on the macroscopic and bulk crystal structure of these materials, our previous work suggests that, as a confined region where charge transfer takes place, the interfacial structures of cathode materials largely dictate their electrochemical performances due to the structural symmetry breaking from 3D (bulk) to 2D (surface), which leads to reconstructions under the different chemical/electrochemical conditions. By summarizing works in this subject and offering our perspectives, this tutorial review will reveal for the first time the correlation between surface structure and interface reconstruction at atomic/molecular scales and their direct impact on corresponding electrochemical performances. More importantly, by extending the knowledge obtained from these three well-studied system, we believe that the same principles established could universally apply to other cathode materials that have been the frontiers of new battery chemistries.

25 ENERGY STORAGE↗
DOE OSTI2026

Machine-learning interatomic potentials for interfaces in all-solid-state batteries: Perspectives on training data, model selection, and validation

Interfaces play a pivotal role in dictating the performance and reliability of all-solid-state batteries (ASSBs), where complex electro-chemo-mechanical phenomena at grain boundaries (GBs) and interfaces can lead to degradation and failure. Traditional atomistic simulation methods, such as first-principles calculations and classical molecular dynamics, face limitations in modeling these interfaces due to either high computational cost or insufficient transferability to the diverse atomic environments evolving at interfaces. Machine-learning interatomic potentials (MLIPs) have emerged as a transformative approach, enabling large-scale, high-accuracy simulations of disordered and chemically complex systems by leveraging the predictability of machine learning models trained on first-principles data. Recent applications of MLIPs have demonstrated their ability to capture intricate behaviors at ASSB interfaces, including ion transport, interfacial evolution, and degradation mechanisms, with accuracy and efficiency unattainable by conventional methods. This prospective paper presents comprehensive analysis and practical guidance for MLIP development for GBs and interfaces in ASSBs, with a focus on three key pillars: data generation, model selection, and validation. Here, we review the current state of MLIP applications for GBs and interfaces in both general and ASSB-specific materials, highlighting best practices and challenges in constructing diverse and representative datasets, choosing appropriate machine learning architectures, and rigorously validating model performance. We also discuss emerging strategies and opportunities for improved reliability and efficiency of MLIPs to simulate realistic interfaces in ASSBs.

Energy - Storage↗
DOE OSTI2024

Tracking copper nanofiller evolution in polysiloxane during processing into SiOC ceramic

Polymer-derived ceramics (PDCs) remain at the forefront of research for a variety of applications including ultra-high-temperature ceramics, energy storage and functional coatings. Despite their wide use, questions remain about the complex structural transition from polymer to ceramic and how local structure influences the final microstructure and resulting properties. This is further complicated when nanofillers are introduced to tailor structural and functional properties, as nanoparticle surfaces can interact with the matrix and influence the resulting structure. The inclusion of crystalline nanofiller produces a mixed crystalline–amorphous composite, which poses characterization challenges. With this study, we aim to address these challenges with a local-scale structural study that probes changes in a polysiloxane matrix with incorporated copper nanofiller. Composites were processed at three unique temperatures to capture mixing, pyrolysis and initial crystallization stages for the pre-ceramic polymer. We observed the evolution of the nanofiller with electron microscopy and applied synchrotron X-ray diffraction with differential pair distribution function (d-PDF) analysis to monitor changes in the matrix's local structure and interactions with the nanofiller. The application of the d-PDF to PDC materials is novel and informs future studies to understand interfacial interactions between nanofiller and matrix throughout PDC processing.

Chemistry↗
DOE OSTI2023

Engineering ligand reactivity enables high-temperature operation of stable perovskite solar cells

Perovskite solar cells (PSCs) consisting of interfacial two- and three-dimensional heterostructures that incorporate ammonium ligand intercalation have enabled rapid progress toward the goal of uniting performance with stability. However, as the field continues to seek ever-higher durability, additional tools that avoid progressive ligand intercalation are needed to minimize degradation at high temperatures. We used ammonium ligands that are nonreactive with the bulk of perovskites and investigated a library that varies ligand molecular structure systematically. Here, we found that fluorinated aniliniums offer interfacial passivation and simultaneously minimize reactivity with perovskites. Using this approach, we report a certified quasi–steady-state power-conversion efficiency of 24.09% for inverted-structure PSCs. In an encapsulated device operating at 85°C and 50% relative humidity, we document a 1560-hour T85 at maximum power point under 1-sun illumination.

14 SOLAR ENERGY↗
NASA NTRS2003

Alloy Design Workbench-Surface Modeling Package Developed

NASA Glenn Research Center's Computational Materials Group has integrated a graphical user interface with in-house-developed surface modeling capabilities, with the goal of using computationally efficient atomistic simulations to aid the development of advanced aerospace materials, through the modeling of alloy surfaces, surface alloys, and segregation. The software is also ideal for modeling nanomaterials, since surface and interfacial effects can dominate material behavior and properties at this level. Through the combination of an accurate atomistic surface modeling methodology and an efficient computational engine, it is now possible to directly model these types of surface phenomenon and metallic nanostructures without a supercomputer. Fulfilling a High Operating Temperature Propulsion Components (HOTPC) project level-I milestone, a graphical user interface was created for a suite of quantum approximate atomistic materials modeling Fortran programs developed at Glenn. The resulting "Alloy Design Workbench-Surface Modeling Package" (ADW-SMP) is the combination of proven quantum approximate Bozzolo-Ferrante-Smith (BFS) algorithms (refs. 1 and 2) with a productivity-enhancing graphical front end. Written in the portable, platform independent Java programming language, the graphical user interface calls on extensively tested Fortran programs running in the background for the detailed computational tasks. Designed to run on desktop computers, the package has been deployed on PC, Mac, and SGI computer systems. The graphical user interface integrates two modes of computational materials exploration. One mode uses Monte Carlo simulations to determine lowest energy equilibrium configurations. The second approach is an interactive "what if" comparison of atomic configuration energies, designed to provide real-time insight into the underlying drivers of alloying processes.

Abel, Phillip B.↗
DOE OSTI2025

Multiphase computational fluid dynamics modeling of reacting flows in absorption columns for carbon capture

First-principles derived computational fluid dynamics (CFD) simulations have been proposed as a fundamental tool for investigating solvent-based CO 2 absorption in packed columns due to their ability to accurately represent the underlying nonlinear, multiscale dynamics. Numerous studies have previously utilized such CFD simulations to investigate hydrodynamics of columns with structured and random packings by assessing the key hydrodynamic metrics such as the interfacial and wetted areas. While mapping such metrics for different conditions is essential to the optimization of absorption columns, it is not sufficient, as the CO 2 capture rate depends also on the coupled, nonlinear dynamics from the underlying chemical reaction kinetics, thermodynamics, and heat-transfer rates. In this work, we present detailed CFD simulation results augmented by incorporating the effects of interfacial physical mass transfer of CO 2 , heat release from chemical reaction kinetics, and thermophysical property variations from resulting temperature gradients. We demonstrate the applicability of the proposed approach in numerically assessing the performance of packed columns by evaluating key hydrodynamic quantities, CO 2 absorption rates, and temperature rise in a reference column with packings that are structurally similar to the Sulzer Mellapak™ 250.Y packing, for different solvent inflow velocities and temperatures. Predictions from simulation results are found to be consistent with the trends in experimental observations from the literature, suggesting that the predictive capabilities of the simulation framework can be leveraged to guide the future development of absorber-column designs and optimized process flowsheets.

Absorption columns↗
DOE OSTI2026

In situ transmission electron microscopy observations of CaCO 3 crystallization onto polysaccharide-coated nanoparticles

Polysaccharides and proteoglycans are widely associated with the organic matrix at sites of CaCO 3 biomineralization, and previous studies indicate that these macromolecules may confer greater roles in mineral nucleation than previously recognized. This investigation uses in situ liquid-phase transmission electron microscopy (LP-TEM) to observe CaCO 3 nucleation onto aminated silica (SiO 2 –NH 3 + ) nanoparticles treated with a layer of chitosan (near-neutral derivative of chitin) or heparin (a carboxylated and highly sulfated glycosaminoglycan). In the absence of polysaccharides, few CaCO 3 particles formed and exhibited mobility. However, the SiO 2 –NH 3 + nanoparticles were enveloped in a region of higher mass density relative to the bulk solution, suggesting the development of a local solute-rich environment that surrounds the charged NH 3 + groups. The heparin- or chitosan-coated silica particles also exhibited regions of higher mass density around the nanoparticles. In the presence of these polysaccharide coatings, we observed the nucleation of abundant CaCO 3 particles whereby the polyanionic heparin promoted more nucleation than the weakly cationic chitosan. Many crystallites appeared to form at the polysaccharide–TEM cell membrane–solution interface, further indicating interfacial and macromolecule-specific control on crystallization. The combined results demonstrate that chitosan and heparin have an appreciable effect on the timing, size, and location of CaCO 3 nucleation compared to the polysaccharide-free nanoparticles.

15 GEOTHERMAL ENERGY↗