Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “grid stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Resistance to Sliding on Atomic Scales

The structure and stability of agglomerates of micron-sized particles is determined by the mechanical properties of the individual contacts between the constituent particles. In this paper we study the possibility of aggregate rearrangements by sliding. Since the contacts between (sub)micron particles are only a few hundred atoms in diameter, processes on atomic levels will play the dominating roll. We study a theoretical model of sliding friction for surfaces that are either flat or contain steps in their grids. The results show that sliding over flat surfaces may produce a large range of friction coefficients, including zero if the adhesive forces are small compared to the binding forces inside a body. However, both grid alignment and steps in the surface will lead to high values for friction. These processes combined virtually eliminate the possibility of sliding in a collision of two (sub)micron sized particles at velocities low enough for sticking to occur. On the other hand we show that in collisions between aggregates sliding may be an important factor for energy dissipation and compaction.

Dominik, C.↗

A Trade-Off Study Between the Primary and Transient Responses of Grid-Forming Inverters

The control parameters of the grid-forming (GFM) inverter-based resources (IBRs) directly impact power system dynamics. The primary control requires the GFM inverter to balance generation and load. It is also preferred that a GFM inverter maintain the terminal frequency after a power system fault. In this paper, we investigate the trade-off between the primary control objective and the transient response. To quantify the transient performance of the GFM inverter, we introduce a new real-time transient stability index (TSI). This index plays a crucial role in our investigation, as it allows us to compare the performance trade-offs of different sets of GFM control parameters.

Lin, Xuheng↗

Design of energy storage system to improve inertial response for large scale PV generation

With high-penetration levels of renewable generating sources being integrated into the existing electric power grid, conventional generators are being replaced and grid inertial response is deteriorating. This technical challenge is more severe with photovoltaic (PV) generation than with wind generation because PV generation systems cannot provide inertial response unless special countermeasures are adopted. To enhance the inertial response, this paper proposes to use battery energy storage systems (BESS) as the remediation approach to accommodate the degrading inertial response when high penetrations of PV generation are integrated into the existing power grid. A sample power system was adopted and simulated using PSS/E software. Here, impacts of different penetration levels of PV generation on the system inertial response were investigated and then BESS was incorporated to improve the frequency dynamics.

25 ENERGY STORAGE↗

The Statistical Emulators of GGCMI Phase 2: Responses of Year-to-Year Variation of Crop Yield to CO 2 , Temperature, Water and Nitrogen Perturbations

Understanding the impact of climate change on year-to-year variation of crop yield is critical to global food stability and security. While crop model emulators are believed to be lightweight tools to replace the models, few emulators have been developed to capture such interannual variation of crop yield in response to climate variability. In this study, we developed a statistical emulator with a machine learning algorithm to reproduce the response of year-to-year variation of four crop yields to CO 2 (C), temperature (T), water (W), and nitrogen (N) perturbations defined in the Global Gridded Crop Model Intercomparison Project (GGCMI) phase 2. The emulators were able to explain more than 52 % of the variance of simulated yield and performed well in capturing the year-to-year variation of global average and gridded crop yield over current croplands in the baseline. With the changes in CO 2 –temperature–water–nitrogen (CTWN) perturbations, the emulators could reproduce the year-to-year variation of crop yield well over most current cropland. The variation of R and the mean absolute error was small under the single CTWN perturbations and dual-factor perturbations. These emulators thus provide statistical response surfaces of yield, including both its mean and interannual variability, to climate factors. They could facilitate spatiotemporal downscaling of crop model simulation, projecting the changes in crop yield variability in the future and serving as a lightweight tool for multi-model ensemble simulation. The emulators enhanced the flexibility of crop yield estimates and expanded the application of large-ensemble simulations of crop yield under climate change.

Climate change↗

Pn-FEM Method for Solving the First-Order Neutron Transport Equation

A deterministic method was investigated and developed for the photon-neutron transport calculation for fusion reactor blanket. Firstly, considering the fact that the second order transport equation cannot describe void region accurately due to the appearance of zero total cross section in the denominator, the first order equation was selected as the starting point of the solution. The angular discretization uses the spherical harmonics (Pn) method. Although discrete ordinates (Sn) method has been most commonly applied due to its efficiency, it suffers from the ray effect. To describe unstructured geometry, the finite element method was used to discrete spatial variable. It is well known that Bubnov-Galerkin discretization of the first-order equation is inappropriate which will create oscillations. To obtain robust solutions, Petrov- Galerkin methods have been developed such as the Streamline-Upwind Petrov-Galerkin (SUPG) method and the Generalized Least-Squares (GLS) method. These methods require a stabilization term added to its test functions, which will incur additional computational cost. Another finite element formulation that usually used for first order equation is the Discontinuous-Galerkin (DG) method. In this method, each element has a unique and separate set of basis function. Then the adjacent elements can be connected by using the in-coming flux. Its main drawback is the number of unknowns, much larger than Continuous-Galerkin (CG) method. The Sub-Grid Scale (SGS) finite element method combines the advantages of CG and DG methods together. It inserts the DG method in each element to correct the CG solution, and provides numerically stable solution of first-order equation without increasing the number of unknowns. The boundary conditions and interface conditions for Pn method is a hard nut to crack. We use Riemann method to deal with this problem. It decomposes the neutron angular flux into in-coming and out-going information through an interface, and applies boundary condition to the in-coming one. (authors)

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Making the Grid "Smart" Through "Smart" Microgrids: Real-Time Power Management of Microgrids with Multiple Distributed Generation Sources Using Intelligent Control

In this Project we collaborated with two DOE National Laboratories, Pacific Northwest National Lab (PNNL) and Lawrence Berkeley National Lab (LBL). Dr. Hammerstrom of PNNL initially supported our project and was on the graduate committee of one of the Ph.D. students (graduated in 2014) who was supported by this project. He is also a committee member of a current graduate student of the PI who was supported by this project in the last two years (August 2014-July 2016). The graduate student is now supported be the Electrical and Computer Engineering (ECE) Department at Montana State University (MSU). Dr. Chris Marney of LBL provided actual load data, and the software WEBOPT developed at LBL for microgrid (MG) design for our project. NEC-Labs America, a private industry, also supported our project, providing expert support and modest financial support. We also used the software “HOMER,” originally developed at the National Renewable Energy Laboratory (NREL) and the most recent version made available to us by HOMER Energy, Inc., for MG (hybrid energy system) unit sizing. We compared the findings from WebOpt and HOMER and designed appropriately sized hybrid systems for our case studies. The objective of the project was to investigate real-time power management strategies for MGs using intelligent control, considering maximum feasible energy sustainability, reliability and efficiency while, minimizing cost and undesired environmental impact (emissions). Through analytic and simulation studies, we evaluated the suitability of several heuristic and artificial-intelligence (AI)-based optimization techniques that had potential for real-time MG power management, including genetic algorithms (GA), ant colony optimization (ACO), particle swarm optimization (PSO), and multi-agent systems (MAS), which is based on the negotiation of smart software-based agents. We found that PSO and MAS, in particular, distributed MAS, were more efficient and better suited for our work. We investigated the following: • Intelligent load control - demand response (DR) - for frequency stabilization in islanded MGs (partially supported by PNNL). • The impact of high penetration of solar photovoltaic (PV)-generated power at the distribution level (partially supported by PNNL). • The application of AI approaches to renewable (wind, PV) power forecasting (proposed by the reviewers of our proposal). • Application of AI approaches and DR for real-time MG power management (partially supported by NEC Labs-America) • Application of DR in dealing with the variability of wind power • Real-time MG power management using DR and storage (partially supported by NEC Labs-America) • Application of DR in enhancing the performance of load-frequency controller • MAS-based whole-sale and retail power market design for smart grid A

24 POWER TRANSMISSION AND DISTRIBUTION↗

Goddard high resolution spectrograph science verification and data analysis

The data analysis performed was to support the Orbital Verification (OV) and Science Verification (SV) of the GHRS was in the areas of the Digicon detector's performance and stability, wavelength calibration, and geomagnetic induced image motion. The results of the analyses are briefly described. Detailed results are given in the form of attachments. Specialized software was developed for the analyses. Calibration files were formatted according to the specifications in a Space Telescope Science report. IRAS images were restored of the Large Magellanic Cloud using a blocked iterative algorithm. The algorithm works with the raw data scans without regridding or interpolating the data on an equally spaced image grid.

Source record↗

A Best Practices System to Enhance CFD Use in Stability and Control Applications

Successful use of CFD to provide aerodynamics for stability and control (S&C) applications will require that the traditional time and costs associated with CFD be reduced and that the errors and uncertainties currently associated with CFD be better understood. CFD will be required to work under a wide range of flow conditions and provide fast and reliable aerodynamics if it is to contribute to this next generation of S&C analyses. CFD solutions have errors and uncertainties due to poorly converged solutions, solution anomalies caused by grids, turbulence models, and parameter selection, and other manifold reasons. In addition to the above problems, there will be a requirement for communications between the CFD expert and the S&C expert and possibly experts from other related disciplines. The CFD expert may not understand the technical problems associated with S&C, and it is almost certain the converse is true.

Morrison, Joseph H.↗

Development of a Common Research Model for Applied CFD Validation Studies

The development of a wing/body/nacelle/pylon/horizontal-tail configuration for a common research model is presented, with focus on the aerodynamic design of the wing. Here, a contemporary transonic supercritical wing design is developed with aerodynamic characteristics that are well behaved and of high performance for configurations with and without the nacelle/pylon group. The horizontal tail is robustly designed for dive Mach number conditions and is suitably sized for typical stability and control requirements. The fuselage is representative of a wide/body commercial transport aircraft; it includes a wing-body fairing, as well as a scrubbing seal for the horizontal tail. The nacelle is a single-cowl, high by-pass-ratio, flow-through design with an exit area sized to achieve a natural unforced mass-flow-ratio typical of commercial aircraft engines at cruise. The simplicity of this un-bifurcated nacelle geometry will facilitate grid generation efforts of subsequent CFD validation exercises. Detailed aerodynamic performance data has been generated for this model; however, this information is presented in such a manner as to not bias CFD predictions planned for the fourth AIAA CFD Drag Prediction Workshop, which incorporates this common research model into its blind test cases. The CFD results presented include wing pressure distributions with and without the nacelle/pylon, ML/D trend lines, and drag-divergence curves; the design point for the wing/body configuration is within 1% of its max-ML/D. Plans to test the common research model in the National Transonic Facility and the Ames 11-ft wind tunnels are also discussed.

Vassberg, John C.↗

Saturated CO{sub 2} absorption near 1.6 μm for kilohertz-accuracy transition frequencies

Doppler-free saturated-absorption Lamb dips were measured on weak rovibrational lines of {sup 12}C{sup 16}O{sub 2} between 6189 and 6215 cm{sup −1} at sub-Pa pressures using optical feedback frequency stabilized cavity ring-down spectroscopy. By referencing the laser source to an optical frequency comb, transition frequencies for ten lines of the 30013←00001 band P-branch and two lines of the 31113←01101 hot band R-branch were determined with an accuracy of a few parts in 10{sup 11}. Involving rotational quantum numbers up to 42, the data were used for improving the upper level spectroscopic constants. These results provide a highly accurate reference frequency grid over the spectral interval from 1599 to 1616 nm.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of the ANL Plant Dynamics Code and Control Strategies for the Supercritical Carbon Dioxide Brayton Cycle and Code Validation with Data from the Sandia Small-Scale Supercritical Carbon Dioxide Brayton Cycle Test Loop

Significant progress has been made in the ongoing development of the Argonne National Laboratory (ANL) Plant Dynamics Code (PDC), the ongoing investigation and development of control strategies, and the analysis of system transient behavior for supercritical carbon dioxide (S-CO 2 ) Brayton cycles. Several code modifications have been introduced during FY2011 to extend the range of applicability of the PDC and to improve its calculational stability and speed. A new and innovative approach was developed to couple the Plant Dynamics Code for S-CO 2 cycle calculations with SAS4A/SASSYS-1 Liquid Metal Reactor Code System calculations for the transient system level behavior on the reactor side of a Sodium-Cooled Fast Reactor (SFR) or Lead-Cooled Fast Reactor (LFR). The new code system allows use of the full capabilities of both codes such that whole-plant transients can now be simulated without additional user interaction. Several other code modifications, including the introduction of compressor surge control, a new approach for determining the solution time step for efficient computational speed, an updated treatment of S-CO 2 cycle flow mergers and splits, a modified enthalpy equation to improve the treatment of negative flow, and a revised solution of the reactor heat exchanger (RHX) equations coupling the S-CO 2 cycle to the reactor, were introduced to the PDC in FY2011. All of these modifications have improved the code computational stability and computational speed, while not significantly affecting the results of transient calculations. The improved PDC was used to continue the investigation of S-CO 2 cycle control and transient behavior. The coupled PDC-SAS4A/SASSYS-1 code capability was used to study the dynamic characteristics of a S-CO 2 cycle coupled to a SFR plant. Cycle control was investigated in terms of the ability of the cycle to respond to a linear reduction in the electrical grid demand from 100% to 0% at a rate of 5%/minute. It was determined that utilization of turbine throttling control below 50% load improves the cycle efficiency significantly. Consequently, the cycle control strategy has been updated to include turbine throttle valve control. The new control strategy still relies on inventory control in the 50%-90% load range and turbine bypass for fine and fast generator output adjustments, but it now also includes turbine throttling control in the 0%-50% load range. In an attempt to investigate the feasibility of using the S-CO 2 cycle for normal decay heat removal from the reactor, the cycle control study was extended beyond the investigation of normal load following. It was shown that such operation is possible with the extension of the inventory and the turbine throttling controls. However, the cycle operation in this range is calculated to be so inefficient that energy would need to be supplied from the electrical grid assuming that the generator could be capable of being operated in a motoring mode with an input electrical energy from the grid having a magnitude of about 20% of the nominal plant output electrical power level in order to maintain circulation of the CO 2 in the cycle. The work on investigation of cycle operation at low power level will be continued in the future. In addition to the cycle control study, the coupled PDC-SAS4A/SASSYS-1 code system was also used to simulate thermal transients in the sodium-to-CO 2 heat exchanger. Several possible conditions with the potential to introduce significant changes to the heat exchanger temperatures were identified and simulated. The conditions range from reactor scram and primary sodium pump failure or intermediate sodium pump failure on the reactor side to pipe breaks and valve malfunctions on the S-CO 2 side. It was found that the maximum possible rate of the heat exchanger wall temperature change for the particular heat exchanger design assumed is limited to ±7 C/s for less than 10 seconds. Modeling in the Plant Dynamics Code has been compared with available data from the Sandia National Laboratories (SNL) small-scale S-CO 2 Brayton cycle demonstration that is being assembled in a phased approach currently at Barber-Nichols Inc. and at SNL in the future. The available data was obtained with an earlier configuration of the S-CO 2 loop involving only a single-turbo-alternator-compressor (TAC) instead of two TACs, a single low temperature recuperator (LTR) instead of both a LTR and a high temperature recuperator (HTR), and fewer than the later to be installed full set of electric heaters. Due to the absence of the full heating capability as well as the lack of a high temperature recuperator providing additional recuperation, the temperature conditions obtained with the loop are too low for the loop conditions to be prototypical of the S-CO 2 cycle.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

An Evaluation of Energy Storage Options for Nuclear Power

Energy supply, distribution, and demand are continuing to evolve as new generation sources come online and new appliances are installed. A larger percentage of the United States (U.S.) energy mix is provided by variable energy sources such as wind and solar each year, and distributed generation is becoming more common. In parallel, an evolution in consumer products such as electrical vehicles, information technology devices for residential and industrial applications, and appliances is changing how energy is consumed. As a result of these trends, nuclear power plants (NPPs) are being called upon to operate more flexibly than ever before. Furthermore, advanced nuclear power plants (A-NPPs) might operate as part of an electricity system that looks very different than when the current NPP fleet was constructed. A-NPPs face the possibility that they will need to operate in an environment where flexibility (e.g., fast ramping) is more highly valued than stability (e.g., baseload generation for conventional demand curves). The current fleet of NPPs is struggling to remain economical in competitive markets in an era of historically low natural gas prices and renewable sources with very low marginal costs. These factors, overlaid with an ambiguous national policy related to nuclear energy and a decision-making context that struggles with multi-decade capital investments, raise key questions and present significant challenges to the economics of nuclear power in the evolving grid. Multiple factors could improve the economics of A-NPPs, including: (1) minimizing the need for active safety systems, (2) minimizing adoption of one-off reactor designs, (3) establishing policies that credit low carbon emitting technologies, and (4) integrating energy storage technologies that increase revenue and reduce costs through a combination of ancillary services, market hedging, and reduced costs via stable operation. This report focuses on Item (4), containing an overview, synthesis, and examination of energy storage options that could be integrated with nuclear generation. Figure 1 provides an overview of the 2015 energy mix by sector, which shows that NPPs are currently used exclusively for electricity generation that is ultimately consumed in the residential, commercial, and industrial sectors. Some areas for NPP energy growth in the future include power generation for electrified transportation and thermal generation for storage and industrial applications. Currently, most industrial thermal energy users combust fossil resources (i.e., coal or natural gas) to meet the energy needs of the processes, but heat from nuclear operations could also be used in certain specific applications.

25 ENERGY STORAGE↗

An Evaluation of Energy Storage Options for Nuclear Power

Energy supply, distribution, and demand are continuing to evolve as new generation sources come online and new appliances are installed. A larger percentage of the United States (U.S.) energy mix is provided by variable energy sources such as wind and solar each year, and distributed generation is becoming more common. In parallel, an evolution in consumer products such as electrical vehicles, information technology devices for residential and industrial applications, and appliances is changing how energy is consumed. As a result of these trends, nuclear power plants (NPPs) are being called upon to operate more flexibly than ever before. Furthermore, advanced nuclear power plants (A-NPPs) might operate as part of an electricity system that looks very different than when the current NPP fleet was constructed. A-NPPs face the possibility that they will need to operate in an environment where flexibility (e.g., fast ramping) is more highly valued than stability (e.g., baseload generation for conventional demand curves). The current fleet of NPPs is struggling to remain economical in competitive markets in an era of historically low natural gas prices and renewable sources with very low marginal costs. These factors, overlaid with an ambiguous national policy related to nuclear energy and a decision-making context that struggles with multi-decade capital investments, raise key questions and present significant challenges to the economics of nuclear power in the evolving grid. Multiple factors could improve the economics of A-NPPs, including: (1) minimizing the need for active safety systems, (2) minimizing adoption of one-off reactor designs, (3) establishing policies that credit low carbon emitting technologies, and (4) integrating energy storage technologies that increase revenue and reduce costs through a combination of ancillary services, market hedging, and reduced costs via stable operation. This report focuses on Item (4), containing an overview, synthesis, and examination of energy storage options that could be integrated with nuclear generation. Figure 1 provides an overview of the 2015 energy mix by sector, which shows that NPPs are currently used exclusively for electricity generation that is ultimately consumed in the residential, commercial, and industrial sectors. Some areas for NPP energy growth in the future include power generation for electrified transportation and thermal generation for storage and industrial applications. Currently, most industrial thermal energy users combust fossil resources (i.e., coal or natural gas) to meet the energy needs of the processes, but heat from nuclear operations could also be used in certain specific applications.

25 ENERGY STORAGE↗

Development of a Novel Accelerator for Neutron Transport Solution Using the Galerkin Spectral Element Methods (Final Report)

This report summarizes the results of a three-year research project sponsored by the U.S. Department of Energy (DOE) Nuclear Energy University Program (NEUP) to develop and implement advanced acceleration schemes for the DOE NEAMS neutronics code PROTEUSSN. The project team included the University of Massachusetts Lowell, The Ohio State University, University of Michigan, and Argonne National Laboratory. The PROTEUS code is a high-fidelity capable deterministic neutron transport code based on unstructured finite element meshes, which solves the steady-state and transient neutron transport problem using the 2nd-order discrete ordinate method (SN2ND), the method of characteristics (MOC), and the advanced nodal transport method (NODAL). The DSA scheme has been implemented in PROTEUS to speed up SN transport calculations. The existing DSA scheme employs a consistent finite element formulation on the same fine mesh structure as the SN solution While the use of consistent discretizations makes the DSA method effective, it does not necessarily make it efficient because the numerical solution of a discretized elliptic diffusion problem itself can be costly, particularly when the problem size becomes large. We developed a new discontinuous Galerkin (DG) discretization of the diffusion equation, called DG-DSA, which can effectively and efficiently accelerate the SN transport iterations. As compared with the previous work, the novelty of our method is that the diffusion equation is solved on a coarse-mesh grid using the DG methods, and the DG diffusion discretization incorporates local hp adaptation, i.e., local adaptation of mesh size and/or polynomial degree, based on local total cross section (or optical thickness). Therefore, the resulting number of degrees of freedom (DOF) of the DG discretization is much less than the conventional consistent DSA discretizations, and thus DG-DSA can achieve significant improvement in computational efficiency. We implemented this scheme in PROTEUS-SN. In addition, we developed a new stabilization scheme named linear prolongation CMFD (lpCMFD). A novel feature of this scheme is that the conventional flat flux ratio–based scaling approach is replaced with a linear interpolation of the scalar flux differences at the coarse-mesh cell edges between the neutron transport and CMFD calculations. Fourier convergence analysis and numerical results show that lpCMFD is unconditionally stable and more effective than other CMFD based on acceleration schemes such as pCMFD, odCMFD. We also developed a new nonlinear diffusion acceleration scheme for solving neutron transport equations. This scheme, called LR-NDA, employs a local refinement approach on the framework of CMFD by solving a local boundary value problem of the scalar flux on the coarse-mesh structure to replace the piecewise constant scalar flux obtained by CMFD. The refined flux is then used to update the scalar flux in the neutron transport source iteration. It has been demonstrated that that LR-NDA is much more effective and stable than CMFD for a wide range of optical thicknesses. LR-NDA is a local adaptive method, which means LR-NDA does not necessarily require local refinement for all the coarse-mesh cells on the problem domain, i.e., it can be used only for relatively optically thick regions where the standard CMFD scheme would encounter the convergence problem.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Operational Assimilation of GOES Data into a Mesoscale Model

A technique has been developed for assimilating GOES-derived skin temperature tendencies and insolation into the surface energy budget equation of a mesoscale model so that the simulated rate of temperature change closely agrees with the satellite observations. A critical assumption of the technique is that the availability of moisture (either from the soil or vegetation) is the least known term in the model's surface energy budget. Therefore, the simulated latent heat flux, which is a function of surface moisture availability, is adjusted based upon differences between the modeled and satellite- observed skin temperature tendencies. An advantage of this technique is that satellite temperature tendencies are assimilated in an energetically consistent manner that avoids energy imbalances and surface stability problems that arise from direct assimilation of surface shelter temperatures. The fact that the rate of change of the satellite skin temperature is used rather than the absolute temperature means that sensor calibration is not as critical. The technique has been employed on a semi-operational basis at the Global Hydrology and Climate Center (GHCC) within the Penn State/National Center for Atmospheric Research (PSU/NCAR) Mesoscale Model (MM5) since 1 November 1998. We performed the assimilation on a model grid centered over the Southeastern US. In addition, a control run without assimilation was performed to provide insight into the performance of the assimilation technique. Bulk verification statistics (BIAS and RMSE) of surface air temperature and relative humidity of more than 250 case days has been performed to date. Results show that assimilation of the satellite data results reduces both the bias and RMSE for simulations of surface air temperature and relative humidity. We are working with forecasters at the National Weather Service Forecast Office located in Birmingham, AL to evaluate the impact of the assimilation on precipitation forecasts. In addition, work is currently underway to determine the ability of both the assimilation technique and Early Eta to sense the significant changes that occur in both leaf expansion and soil moisture conditions during the Spring-Summer of 1999. This will be accomplished via examination of the simulated surface energy budgets from both modeling systems.

Lapenta, William↗

Large eddy simulation of atmospheric boundary layer flow over complex terrain in comparison with RANS simulation and on-site measurements under neutral stability condition

Large eddy simulation (LES) of the atmospheric boundary layer (ABL) flow over complex terrain is presented with a validation using meteorological tower (met-tower) data through an improved neutral stability sampling approach. The proposed stability sampling procedure includes a condition based on the most-likely occurrence time-periods of the neutral ABL and reduces the variabilities of the conditional wind statistics calculated at the met-towers in comparison to our previous work. The ABL flow simulations are carried out over a potential wind site with a prominent hill based using the OpenFOAM-based simulator for on/off-shore wind farm applications by applying the Lagrangian-averaged scale-invariant dynamic sub-grid scale turbulence model. A low-dissipative scale-selective discretization scheme for the non-linear convection term in the LES governing equation is adopted implicitly to ensure both the second-order accuracy and bounded solution. The LES inflow is generated through a precursor method with a “tiling” approach based on the flow driving parameters obtained from a corresponding Reynolds-averaged Navier–Stokes (RANS) simulation. Overall, the averaged wind velocity profiles predicted by the LES approach at all met-tower locations show a similar tendency as the RANS results, which are also in reasonable agreement with the met-tower data. An obvious difference in wind speed standard deviation profiles is seen between LES and RANS, especially at regions downstream of the hill edge, where the LES shows under-predicted results at the highest measurement levels in comparison to the tower data. The computational costs of the LES are found to be about 20 times higher than the RANS simulations.

Energy & Fuels↗

Implementational Aspects for the Characterization of Low-Inertia in Power Systems

The replacement of conventional generating units with non-conventional renewable energy resources impacts the stability of the power system. While the general goal of supplying demand could be achieved from both generation resources, inverter-based energy resources are different from traditional synchronous machines in the sense that they do not inherently provide inertia to the system. The latter obviously worsen the system ability to maintain the balance between supply and demand after certain contingencies such as generator outages. With high integration of renewable-based generation resources, there is a reduction in total system inertia, which could lead to systems with less time to react for frequency restoration in case of such unexpected unit failures. While conceptually it is true, there is a missing gap in the field of power system stability community in terms of test-bed power systems for characterizing low-inertia conditions. In this paper, a framework for low-inertia power systems is presented. The purpose of the test-bed is to establish an environment for testing and conducting research on power systems experiencing low-inertia issues. The frequency nadir, the rate of change of frequency, and the under-frequency load shedding scheme are used as a measure of the healthiness of power grids.

Baquedano-Aguilar, Mario D.↗