Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “function composition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Post impact compressive strength in composites

Presented in this paper are the plan, equipment, procedures, and findings of an experimental investigation of the tolerance to low velocity impact of a graphite epoxy (AS4/3501-6) and graphite bismaleimide (M6/CYCOM3100) advanced composites. The applied impacts were governed by the Air Force Guide Specification 87221. Specimens of each material system having a common nominal layup (10% 0 deg; 80% +/-45 deg; 10% 90 deg), a common 7 inch (17.78 cm) by 10 inch (25.40 cm) size, five different thicknesses (9, 26, 48, 74, and 96 plies), and ambient moisture content were impacted and strength tested at room temperature. Damaged areas and post impact compression strengths (PICS) were among the most significant findings obtained. While the undamaged per ply compression strength of both materials is a strong function of laminate thickness, the per ply PICS is not. The average difference in per ply PICS between the two material systems is about seven percent. Although a smaller percentage of the applied kinetic energy was absorbed by the Gr/BMI than by the Gr/Epoxy composites, larger damaged areas were produced in the Gr/BMI than in Gr/Epoxy. Within the limitations of this investigation, the Gr/BMI system seems to offer no advantage in damage tolerance over the Gr/Epoxy system examined.

Demuts, Edvins↗

QSO envelopes - Optically thin, low density, and normal abundances

Consideration of a family of photoionization models which are optically thin to the ionizing radiation, have low enough density that collisional de-excitation is unimportant, and have normal (cosmic) chemical abundances. The line ratios from all such models with a given form of the ionizing spectrum can be derived by means of a scaling law from a single numerical calculation and expressed as a function of one physical parameter. The value of the parameter is uniquely determined from the observed line ratios. The resulting model is in reasonably good agreement with the typical or composite QSO spectrum and with line intensities for two recently observed individual QSOs. It is therefore suggested that much of the emission may come from optically thin gas, although some of the observational evidence (especially the strength of Mg II 2800 A) indicates that thick gas may also be present in some objects.

Scargle, J. D.↗

Conference on In Situ Composites, 2nd, Bolton Landing, N.Y., September 2-5, 1975, Proceedings

The present collection of papers deals with advances in several areas of interest in in-situ composites. Major areas discussed include solidification and structural control, physical properties, mechanical behavior, stability, environmental response, and development of new metallic and ceramic systems. New evidence about directional solidification in terms of temperature gradients is presented along with solidification rates for successful formation of in-situ composite structures. Much is learned about the factors that control structure in directionally solidified eutectic alloys and the relationship of properties to structure, especially the change in properties as a function of operating environment. Less progress is achieved in the area of physical properties than in the area of mechanical properties. Individual items are announced in this issue.

Jackson, M. R.↗

Observed distribution functions of H, He, C, O, and Fe in corotating energetic particle streams: Implications for interplanetary acceleration and propagation

Distribution functions for H, He, C, O, and Fe derived from our IMP 8 measurements of approximately 0.15 to approximately 8 MeV/nucleon particles in three corotating streams observed near earth are shown to have a simple exponential dependence on the particle speed. The e-folding speed, v sub o, is typically 0.01c, is found to be the same for the distribution functions of all elements examined, and varies little from one corotating event to the next. The relative abundances of energetic particles in these events resemble most closely the solar coronal composition and, thus, presumably that of the solar wind. These results may imply that the acceleration of these particles, which occurs in corotating interaction regions at several AU from the sun, is by a statistical process.

Gloeckler, G.↗

Observed distribution functions of H, He, C, O, and Fe in corotating energetic particle streams - Implications for interplanetary acceleration and propagation

Distribution functions for H, He, C, O, and Fe derived from our IMP 8 measurements of about 0.15 to 8 MeV per nucleon particles in three corotating streams observed near Earth are shown to have a simple exponential dependence on the particle speed. The e-folding speed, typically 0.01c, is found to be the same for the distribution functions of all elements examined, and varies little from one corotating event to the next. The relative abundances of energetic particles in these events resemble most closely the solar coronal composition and thus, presumably, that of the solar wind. These results may imply that acceleration of these particles, which occurs in corotating interaction regions at several AU from the sun, is by a statistical process.

Gloeckler, G.↗

Electron beam induced damage in ITO coated Kapton

Data for the stability of thin conductive indium tin oxide films on 0.003 inch thick Kapton substrates during exposure of the surface to electron beams are reported. The electron beam energy was 3 keV and the diameter was about 0.8 mm. Thermal effects and surface modifications are considered. For primary current greater than 0.6 microamperes, an obvious dark discoloration with diameter approximately that of the beam was produced. The structure of the discolored region was studied with the scanning electron microscope, and the findings are stated. Surface modifications were explored by AES, obtaining spectra and secondary emission coefficient as a function of time for different beam intensities. In all cases beam exposure results in a decrease of the secondary yield but because of thermal effects this change, as well as composition changes, cannot be directly interpreted in terms of electron beam dosage.

Krainsky, I.↗

Advanced methods for preparation and characterization of infrared detector materials

Crystals were prepared by the Bridgman-Stockbarger method with a wide range of crystal growth rates and temperature gradients adequate to prevent constitutional supercooling under diffusion-limited, steady-state, growth conditions. The longitudinal compositional gradients for different growth conditions and alloy compositions were calculated and compared with experimental data to develop a quantitative model of solute redistribution during the crystal growth of the alloys. Measurements were performed to ascertain the effect of growth conditions on radial compositional gradients. The pseudobinary HgTe-CdTe constitutional phase diagram was determined by precision differential-thermal-analysis measurements and used to calculate the segregation coefficient of Cd as a function of x and interface temperature. Experiments were conducted to determine the ternary phase equilibria in selected regions of the Hg-Cd-Te constitutional phase diagram. Electron and hole mobilities as functions of temperature were analyzed to establish charge-carrier scattering probabilities. Computer algorithms specific to Hg(1-x)CdxTe were developed for calculations of the charge-carrier concentration, charge-carrier mobilities, Hall coefficient, and Dermi Fermi energy as functions of x, temperature, ionized donor and acceptor concentrations, and neutral defect concentrations.

Broerman, J. G.↗

Collisions with ice-volatile objects: Geological implications

The collision of the Earth with extra-terrestrial ice-volatile bodies is proposed as a mechanism to produce rapid changes in the geologic record. These bodies would be analogs of the ice satellites found for the Jovian planets and suspected for comets and certain low density bodies in the Asteroid belt. Five generic end-members are postulated: (1) water ice; (2) dry ice: carbon-carbon dioxide rich, (3) oceanic (chloride) ice; (4) sulfur-rich ice; (5) ammonia hydrate-rich ice; and (6) clathrate: methane-rich ice. Due to the volatile nature of these bodies, evidence for their impact with the Earth would be subtle and probably best reflected geochemically or in the fossil record. Actual boloids impacting the Earth may have a variable composition, generally some admixture with water ice. However for discussion purposes, only the effects of a dominant component will be treated. The general geological effects of such collisions, as a function of the dominant component would be: (1) rapid sea level rise unrelated to deglaciation, (2) decreased oceanic pH and rapid climatic warming or deglaciation; (3) increased paleosalinities; (4) increased acid rain; (5) increased oceanic pH and rapid carbonate deposition; and (6) rapid climatic warming or deglaciation.

Wilde, P.↗

Velocities and rotational excitation of interstellar H2 toward Pi Scorpii

A spectrum of Pi Sco showing numerous atomic lines and 70 absorption features from the Lyman and Werner transitions of interstellar H2 in rotational level J from zero to five is presented. Their shapes of the composite column density profiles are very nearly Gaussian with a one-dimensional rms velocity dispersion of 3 km/s. The behavior of shifts in the inferred N(H2) as a function of velocity are consistent with the overall profiles being composed of nearly symmetrical, tightly paced assemblies of about seven unresolved components. The relative overall column densities in the higher J levels of H2 are consistent with a model where these states are populated by optical pumping through the Lyman and Werner transitions, powered by UV radiation from nearby stars. The slight narrowing of the high-J profiles may be due to small clumps of H2 at radial velocities some 5-8 km/s from the core of the profile are exposed to a pumping flux about 10 times lower than that for the material near the profile's center.

Jenkins, Edward B.↗

A finite element-boundary integral method for cavities in a circular cylinder

Conformal antenna arrays offer many cost and weight advantages over conventional antenna systems. However, due to a lack of rigorous mathematical models for conformal antenna arrays, antenna designers resort to measurement and planar antenna concepts for designing non-planar conformal antennas. Recently, we have found the finite element-boundary integral method to be very successful in modeling large planar arrays of arbitrary composition in a metallic plane. We extend this formulation to conformal arrays on large metallic cylinders. In this report, we develop the mathematical formulation. In particular, we discuss the shape functions, the resulting finite elements and the boundary integral equations, and the solution of the conformal finite element-boundary integral system. Some validation results are presented and we further show how this formulation can be applied with minimal computational and memory resources.

Kempel, Leo C.↗

Probabilistic assessment of uncertain adaptive hybrid composites

Adaptive composite structures using actuation materials, such as piezoelectric fibers, were assessed probabilistically utilizing intraply hybrid composite mechanics in conjunction with probabilistic composite structural analysis. Uncertainties associated with the actuation material as well as the uncertainties in the regular (traditional) composite material properties were quantified and considered in the assessment. Static and buckling analyses were performed for rectangular panels with various boundary conditions and different control arrangements. The probability density functions of the structural behavior, such as maximum displacement and critical buckling load, were computationally simulated. The results of the assessment indicate that improved design and reliability can be achieved with actuation material.

Shiao, Michael C.↗

Simulation and Comparison of Martian Surface Ionization Radiation

The spectrum of energetic particle radiation and corresponding doses at the surface of Mars is being characterized by the Radiation Assessment Detector (RAD), one of ten science instruments on the Mars Science Laboratory (MSL) Curiosity Rover. The time series of dose rate for the first 300 Sols after landing on Mars on August 6, 2012 is presented here. For the comparison to RAD measurements of dose rate, Martian surface ionization radiation is simulated by utilizing observed space quantities. The GCR primary radiation spectrum is calculated by using the Badhwar-O'Neill 2011 (BO11) galactic cosmic ray (GCR) model, which has been developed by utilizing all balloon and satellite GCR measurements since 1955 and the newer 1997-2012 Advanced Composition Explorer (ACE) measurements. In the BO11 model, solar modulation of the GCR primary radiation spectrum is described in terms of the international smoothed sunspot number and a time delay function. For the transport of the impingent GCR primary radiation through Mars atmosphere, a vertical distribution of atmospheric thickness at each elevation is calculated using the vertical profiles of atmospheric temperature and pressure made by Mars Global Surveyor measurements. At Gale Crater in the southern hemisphere, the seasonal variation of atmospheric thickness is accounted for the daily atmospheric pressure measurements of the MSL Rover Environmental Monitoring Station (REMS) by using low- and high-density models for cool- and warm-season, respectively. The spherically distributed atmospheric distance is traced along the slant path, and the resultant directional shielding by Martian atmosphere is coupled with Curiosity vehicle for dose estimates. We present predictions of dose rate and comparison to the RAD measurements. The simulation agrees to within +/- 20% with the RAD measurements showing clearly the variation of dose rate by heliospheric conditions, and presenting the sensitivity of dose rate by atmospheric pressure, which has been found from the RAD experiments and driven by thermal tides on Martian surface.

Kim, Myung-Hee Y.↗

Coronagraphic Observations of the Lunar Sodium Exosphere 2018-2019

Remote observations of the lunar sodium corona have been obtained with the Goddard Lunar Coronagraph located at the Winer Observatory in Sonoita, Arizona. We previously reported the results of observations in the spring, 2017, observing season (Killen et al., 2019). We report herein the results of the 2018–2019 observing campaign. We show definitive effects on the corona - the extended lunar sodium exosphere above 150 km from the surface - of enhanced ion flux onto the Moon as measured by the ARTEMIS ElectroStatic Analyzer. The three observations in this dataset with the largest column abundances are associated with entrance of the Moon into the magnetosheath. The enhancement in the exosphere due to ion flux is not long-lived after the enhanced ion influx decreases, confirming the findings of Killen et al., 2012. The column abundance is greatest at both the dawn and dusk terminators as predicted and simulated by Smyth and Marconi, 1995. The cause of the increased scale height at the terminators is consistent with radiation pressure acceleration anti-sunward. We report a shallow decline of column abundance with increasing latitude which is also consistent with radiation pressure acceleration. Most of our measured scale heights are on the order of 800–1800 km, increasing at high latitudes, consistent with the data set published in Killen et al., 2019. Although the intensity extrapolated to the surface decreases with latitude, the scale height increases with latitude, so that the exospheric column decreases more slowly with increasing latitude than does a cosine function.

moon↗

Molecular Dynamics Investigation of the Structural and Mechanical Properties of Off-Stoichiometric Epoxy Resins

Molecular dynamic (MD) simulations were performed to compute the mechanical properties of off-stoichiometric epoxy resins as a function of hardener/epoxy mixture ratio (r). Properties were characterized in relation to their microscopic structures. Such resins have been used recently for adhesive-free bonding of large-scale composite structures using the co-curing-ply method. In this process, two partially precured composite panels with hardener-poor (HP) off-stoichiometric resins are coupled with ply(ies) of complementary hardener-rich (HR) formulations and then cured simultaneously. This bonding process has the potential to produce reliable and certifiable composite joints without the need for additional fasteners, which are often required for many conventional bonding methods because even small amounts of contamination can cause a weak bond. The reflow and mixing of the HP/HR resin in this bonding process result in a joint with no discernable interface that should not be susceptible to surface contamination. However, incomplete mixing of the two offset resins may result in chemical heterogeneity of the cured polymeric joint. Thus, different r values may be obtained across the joint. Classical MD simulations were performed to compute the Young’s modulus of polymers with different r values and correlate their properties to network structures. High stiffness was associated with molecular packing due to chemical crosslinking, leading to a single network structure. Moreover, the networks became denser as the ratio approached the stoichiometric value r = 1. Thus, the r = 1 systems were single clusters, with high stiffness, high molecular weight, and a high degree of crosslinking. Structural properties such as radius of gyration and mean square displacement were determined to investigate the variation in the stiffness with respect to r. This MD simulation study was validated with experimental measurements.

Chang Woon Jang↗

SelenITA: A dual-spacecraft lunar CubeSat mission to characterize the near-surface electromagnetic plasma environment

SelenITA is an international interdisciplinary mission consisting of two CubeSats that will provide the first multi-point measurement in a sustained low lunar orbit. This mission will advance the understanding of spatiotemporal differentiation of the electromagnetic space environment at the Moon in support of Artemis crew and the geosciences. The mission science objectives are to: (1) further constrain the origins of crustal magnetic fields and their applications; (2) determine the nature of plasma interactions with crustal magnetic fields; (3) characterize plasma waves and turbulence at the Moon; (4) characterize the lunar surface potential in all plasma environments; (5) constrain the composition, thermal state, and structure of the lunar upper mantle and crust; (6) characterize the ionizing radiation in lunar orbit; (7) determine the density of the dust exosphere as a function of latitude, longitude, and altitude, including the lunar polar space environment. The measurement requirements include: 3-component vector magnetic field, plasma distribution (flux, energy, density, temperature), energetic particles (protons, electrons, gamma rays), and dust. SelenITA builds on a rich history of electromagnetic plasma observations of the near lunar surface and space environment, and it answers high level science questions with state of the art instruments in a small package. PLAIN LANGUAGE ABSTRACT – SelenITA comes from the greek word for Moon, selene, with the addition of “ITA” as a reference to the Brazilian teammate, Instituto Tecnológico de Aeronáutica. In addition, in Portuguese "ita" is a prefix similar to "ite" in English, used in naming minerals, so Selenita could be seen as a lunar gemstone. In Spanish, “ita” is a diminutive suffix for “little” which is appropriate for this CubeSat mission which consists of twin 12U CubeSats in low lunar orbit. The primary science goal of the mission is to distinguish time varying features within the electromagnetic plasma environment near the surface of the Moon. The science objectives include investigating the origins of crustal magnetic fields, plasma interactions with these fields, plasma waves, surface potential, and interior properties. This mission is also interested in the radiation environment at the Moon and the amount of dust at the lunar poles. This is important because it helps us understand how future astronauts will live and work on the lunar surface and identify hazards.

space weather↗

SelenITA: A Dual-Spacecraft Lunar Cubesat Mission to Characterize the Near-Surface Electromagnetic Plasma Environment

SelenITA is an international interdisciplinary mission consisting of two CubeSats that will provide the first multi-point measurement in a sustained low lunar orbit. This mission will advance the understanding of spatiotemporal differentiation of the electromagnetic space environment at the Moon in support of Artemis crew and the geosciences. The mission science objectives are to: (1) further constrain the origins of crustal magnetic fields and their applications; (2) determine the nature of plasma interactions with crustal magnetic fields; (3) characterize plasma waves and turbulence at the Moon; (4) characterize the lunar surface potential in all plasma environments; (5) constrain the composition, thermal state, and structure of the lunar upper mantle and crust; (6) characterize the ionizing radiation in lunar orbit; (7) determine the density of the dust exosphere as a function of latitude, longitude, and altitude, including the lunar polar space environment. The measurement requirements include: 3-component vector magnetic field, plasma distribution (flux, energy, density, temperature), energetic particles (protons, electrons, gamma rays), and dust. SelenITA builds on a rich history of electromagnetic plasma observations of the near lunar surface and space environment, and it answers high level science questions with state of the art instruments in a small package.

space weather↗

SelenITA: A Dual-Spacecraft Lunar CubeSat Mission to Characterize the Near-Surface Electromagnetic Plasma Environment

SelenITA is an international interdisciplinary mission consisting of two CubeSats that will provide the first multi-point measurement in a sustained low lunar orbit. This mission will advance the understanding of spatiotemporal differentiation of the electromagnetic space environment at the Moon in support of Artemis crew and the geosciences. The mission science objectives are to: (1) further constrain the origins of crustal magnetic fields and their applications; (2) determine the nature of plasma interactions with crustal magnetic fields; (3) characterize plasma waves and turbulence at the Moon; (4) characterize the lunar surface potential in all plasma environments; (5) constrain the composition, thermal state, and structure of the lunar upper mantle and crust; (6) characterize the ionizing radiation in lunar orbit; (7) determine the density of the dust exosphere as a function of latitude, longitude, and altitude, including the lunar polar space environment. The measurement requirements include: 3-component vector magnetic field, plasma distribution (flux, energy, density, temperature), energetic particles (protons, electrons, gamma rays), and dust. SelenITA builds on a rich history of electromagnetic plasma observations of the near lunar surface and space environment, and it answers high level science questions with state of the art instruments in a small package. PLAIN LANGUAGE ABSTRACT – SelenITA comes from the greek word for Moon, selene, with the addition of “ITA” as a reference to the Brazilian teammate, Instituto Tecnológico de Aeronáutica. In addition, in Portuguese "ita" is a prefix similar to "ite" in English, used in naming minerals, so Selenita could be seen as a lunar gemstone. In Spanish, “ita” is a diminutive suffix for “little” which is appropriate for this CubeSat mission which consists of twin 12U CubeSats in low lunar orbit. The primary science goal of the mission is to distinguish time varying features within the electromagnetic plasma environment near the surface of the Moon. The science objectives include investigating the origins of crustal magnetic fields, plasma interactions with these fields, plasma waves, surface potential, and interior properties. This mission is also interested in the radiation environment at the Moon and the amount of dust at the lunar poles. This is important because it helps us understand how future astronauts will live and work on the lunar surface and identify hazards.

space weather↗

A Robust Biomarker

Polymers of bacterial origin, either through cell secretion or the degraded product of cell lysis, form isolated mucoidal strands as well as well-developed biofilms on interfaces. Biofilms are structurally and compositionally complex and are readily distinguishable from abiogenic films. These structures range in size from micrometers to decimeters, the latter occurring as the well-known, mineralised biofilms called stromatolites. Compositionally bacterial polymers are greater than 90 % water, with while the majority of the macromolecules forming the framework of the polymers consisting of polysaccharides (with and some nucteic acids and proteins). These macromolecules contain a vaste amount of functional groups, such as carboxyls, hydroxyls, and phosphoryls which are implicated in cation-binding. It is the elevated metal- binding capacity which provides the bacterial polymer with structural support and also helps to preserves it for up to 3.5 b.y. in the terrestrial rock record. The macromolecules, thus, can become rapidly mineralised and trapped in a mineral matrix. Through early and late diagenesis (bacterial degradation, burial, heat, pressure and time) they break down, losing the functional groups and, gradually, their hydrogen atoms. The degraded product is known as "kerogen". With further diagenesis and metamorphism, all the hydrogen atoms are lost and the carbonaceous matter becomes graphite. until the remnant carbonaceous material become graphitised. This last sentence reads a bit as if ALL these macromolecules break down and end up as graphite., but since we find 441 this is not true for all of the macromolecules. We have traced fossilised polymer and biofilms in rocks from throughout Earth's history, to rocks as old as the oldest being 3.5 b.y.-old. Furthermore, Time of Flight Secondary Ion Mass Spectrometry has been able to identify individual macromolecules of bacterial origin, the identities of which are still being investigated, in all the samples containing fossil biofilm, including the 3.5 b.y..-old carbonaceous cherts from South Africa and Australia. As a result of the unique compositional, structural and "mineralisable" properties of bacterial polymer and biofilms, we conclude that bacterial polymers and biofilms constitute a robust and reliable biomarker for life on Earth and could be a potential biomarker for extraterrestrial life.

Westall, F.↗