Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “edge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Three-dimensional inhomogeneity of electron-temperature-gradient turbulence in the edge of tokamak plasmas

Nonlinear multiscale gyrokinetic simulations of a Joint European Torus edge pedestal are used to show that electron-temperature-gradient (ETG) turbulence has a rich three-dimensional structure, varying strongly according to the local magnetic-field configuration. In the plane normal to the magnetic field, the steep pedestal electron temperature gradient gives rise to anisotropic turbulence with a radial (normal) wavelength much shorter than in the binormal direction. In the parallel direction, the location and parallel extent of the turbulence are determined by the variation in the magnetic drifts and finite-Larmor-radius (FLR) effects. The magnetic drift and FLR topographies have a perpendicular-wavelength dependence, which permits turbulence intensity maxima near the flux-surface top and bottom at longer binormal scales, but constrains turbulence to the outboard midplane at shorter electron-gyroradius binormal scales. Here our simulations show that long-wavelength ETG turbulence does not transport heat efficiently, and significantly decreases overall ETG transport—in our case by ~40%—through multiscale interactions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Inference of main ion particle transport coefficients with experimentally constrained neutral ionization during edge localized mode recovery on DIII-D

Abstract The plasma and neutral density dynamics after an edge localized mode are investigated and utilized to infer the plasma transport coefficients for the density pedestal. The Lyman-Alpha Measurement Apparatus (LLAMA) diagnostic provides sub-millisecond profile measurements of the ionization and neutral density and shows significant poloidal asymmetries in both. Exploiting the absolute calibration of the LLAMA diagnostic allows quantitative comparison to the electron and main ion density profiles determined by charge-exchange recombination, Thomson scattering and interferometry. Separation of diffusion and convection contributions to the density pedestal transport are investigated through flux gradient methods and time-dependent forward modeling with Bayesian inference by adaptation of the Aurora transport code and IMPRAD framework to main ion particle transport. Both methods suggest time-dependent transport coefficients and are consistent with an inward particle pinch on the order of 1 m s −1 and diffusion coefficient of 0.05 m 2 s −1 in the steep density gradient region of the pedestal. While it is possible to recreate the experimentally observed phenomena with no pinch in the pedestal, low diffusion in the core and high outward convection in the near scrape-off layer are required without an inward pedestal pinch.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Broadening of microwave heating beams in the DIII-D tokamak by edge turbulence

Abstract We have demonstrated for the first time that turbulent plasma density fluctuations in the edge of the DIII-D tokamak are responsible for substantial broadening of an injected microwave beam by successful quantitative comparison between experimental observations and first principles 2D full-wave simulations. The broadening of the beam has important implications for control of tokamak discharges through localized electron cyclotron deposition needed for eliminating magnetohydrodynamic instabilities. This new predictive capability is mandatory to design & operate present & future tokamaks in such a way that microwave heating schemes achieve their intended objectives.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

How turbulent transport broadens the heat flux width: local SOL production or edge turbulence spreading?

This paper uses data from limited HL-2A Ohmic-plasma to answer the question of how turbulent transport broadens the heat flux width. A key issue in this study is the determination of the origin of scrape-off layer (SOL) turbulence. We develop the concept of the energy production ratio ${R_a}$, which compares the flux of turbulence energy across the last closed flux surface (LCFS) to the net, integrated energy production in the SOL. The flux of turbulence energy (i.e. spreading) is measured directly, using Langmuir probes. Experimental data is used to evaluate ${R_a}$. Results show that usually ${R_a} > 1$, indicating that SOL turbulence is energized primarily by edge turbulence spreading. The exceptions—cases where ${R_a} < 1$—are those with relatively stronger ${\mathbf{E}} \times {\mathbf{B}}$ shear near the LCFS. The latter inhibits both turbulence spreading and local SOL production, but has greater effects on spreading. High blob fraction in the turbulence correlates with large values of ${R_a}$. The implications for heat flux width physics are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Tokamak edge localized mode onset prediction with deep neural network and pedestal turbulence

Abstract A neural network, BES-ELMnet, predicting a quasi-periodic disruptive eruption of the plasma energy and particles known as edge localized mode (ELM) onset is developed with observed pedestal turbulence from the beam emission spectroscopy system in DIII-D. BES-ELMnet has convolutional and fully-connected layers, taking two-dimensional plasma fluctuations with a temporal window of size 128 µ s and generating a scalar output which can be interpreted as a probability of the upcoming ELM onset. As approximately labeled inter-ELM broadband ( 15 kHz ⩽ f ⩽ 150 kHz ) fluctuations are given to the network, BES-ELMnet learns by itself ELM-related precursors arising before the onsets through supervised learning scheme. BES-ELMnet achieves the gradually increasing ELM onset probabilities between two consecutive ELMs during the inter-ELM phases and can forecast the first ELM onsets which occur after the high confinement mode transition. We further investigate the network generality in terms of the selected frequency band to ensure the use of BES-ELMnet for various operation regimes without changing the trained architecture. Therefore, our novel prediction method will enhance a proactive high confinement mode control of fusion-grade plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Decoupling of peeling and ballooning thresholds for pedestal stability and reduction in ELM frequency via enhanced turbulence with edge electron cyclotron heating in DIII-D

Abstract The edge localized mode (ELM) frequency ( f ELM ) decreased by 63% when electron cyclotron heating (ECH) deposition location is shifted from ρ = 0.4 to ρ = 0.8 in DIII-D discharges where the power ratio between neutral beam injection (NBI) and ECH ( P NBI / P ECH ) is kept at ∼1. The performance of the pedestal in the ECH heated case is compared with a pure NBI reference discharge while keeping the total input power constant. All these discharges are performed at balanced input torque conditions. Furthermore, in the pure NBI discharge a strong decoupling of the peeling–ballooning (PB) thresholds is observed. The PB decoupling is preserved when the ECH is deposited at ρ = 0.8 and P NBI / P ECH ∼ 1, while the thresholds manifest a closed stability boundary when the ECH is deposited at ρ = 0.4. The inter-ELM pedestal recovery time is considerably larger for the ECH at ρ = 0.8 case. Increased pedestal turbulence is observed in beam emission spectroscopy (BES), Doppler backscattering and magnetic diagnostics for the ECH at the ρ = 0.8 case. Strong growth of a TEM-like mode is observed in BES and the mode growth is correlated with the decrease in f ELM . In view of these observations, the increased pedestal turbulence seems to be the plausible reason behind the delayed pedestal recovery following an ELM event in the ECH at ρ = 0.8 case, and the preservation of PB decoupling through temperature pedestal profile widening. TRANSP interpretative simulations show that the ECH at the ρ = 0.8 case is more susceptible to ITG/TEM turbulence.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Electron transport barrier and high confinement in configurations with internal islands close to the plasma edge of W7-X

The low magnetic shear in the Wendelstein 7-X (W7-X) stellarator makes it feasible to shape the separatrix by the large islands constituting an island-divertor, and this can be exploited to access various magnetic configurations, including samples of different internal island sizes and locations. To investigate the configuration effects on the plasma confinement, a configuration scan was performed by changing the coil currents to vary the rotational transform between values 5/4 and 5/6 at the plasma boundary with different power levels (2, 4, 6 MW) of electron cyclotron resonance heating (ECRH) at a maximum plasma density of 8 × 10 19 m -2 . neutral beam injection (NBI) heating was also applied during some configurations of the scan to create a density ramp and access high densities beyond the X2 ECRH cutoff. For the magnetic configurations, where the 5/5 and 5/6 island chains were moved closer to separatrix but remaining inside the last closed flux surface, the electron cyclotron emission shows that an electron temperature, T e , pedestal develops already during ECRH heated plasma buildup phase indicating a transport barrier, and the barrier sustains irrespective of changed plasma heating conditions such as NBI in the later part of discharge. The transport barrier is broken by subsequent fast crashes, observed with multiple plasma diagnostics with characteristics such as tokamak edge localized modes, and the corresponding crash amplitude and frequency vary with plasma pressure. The impact of the transport barrier on plasma confinement can be seen through the increased core T e profile, which could be responsible for the overall increase in the stored diamagnetic energy by approximately 10% for these configurations. After the plasma heating is terminated, a backwards transition to a degraded confinement state is also observed. These observations indicate a configuration triggered high confinement mode in low shear W7-X. This work focuses on the occurrence of this transport barrier for different magnetic configurations and its relation to internal magnetic islands.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Enhanced pedestal transport driven by edge collisionality on Alcator C-Mod and its role in regulating H-mode pedestal gradients

Experimental measurements of plasma and neutral profiles across the pedestal are used in conjunction with 2D edge modeling to examine pedestal stiffness in Alcator C-Mod H-mode plasmas. Enhanced D α experiments on Alcator C-Mod observed pedestal degradation and loss in confinement below a critical value of net power crossing the separatrix, P net = $P^{crit}_{net}$ ≈ 2.3 MW, in the absence of any external fueling. New analysis of ionization and particle flux profiles reveal saturation of the pedestal electron density, $n^{ped}_{e}$, despite continuous increases in ionization throughout the pedestal, inversely related to P net . A limi to the pedestal $\nabla$n e emerges as the particle flux, Γ D , continues to grow, implying increases in the effective particle diffusivity, D eff . This is well-correlated with the separatrix collisionality, $v^*_{sep}$ and a turbulence control parameter, α t , implying a possible transition in type of turbulence. The transition is well correlated with the experimentally observed value of $P^{crit}_{net}$. SOLPS-ITER modeling is performed for select discharges from the power scan, constrained with experimental electron and neutral densities, measured at the outer midpane. The modeling confirms general growth in D eff , consistent with experimental findings, and additionally suggests even larger growth in Χ e at the same $P^{crit}_{net}$.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Mitigation of ICRF—edge plasma interaction in Alcator C-Mod

The parasitic interaction between ion cyclotron range of frequencies (ICRF) waves and the edge plasma has long limited high-power ICRF utilization in magnetically confined fusion plasmas. In this paper, we report on the successful mitigation of this interaction by power tapering a four-strap field-aligned (FA) antenna in the Alcator C-Mod tokamak. With the antenna operated in dipole phasing ($0\pi0\pi$), the ratio of the power coupled by the central two straps ($P_\mathrm {cent}$) to the power coupled by the outer two straps was varied at fixed total coupled ICRF power ($P_\mathrm {tot}$). With $P_\mathrm {cent}$/$P_\mathrm {tot} \approx 0.8-0.9$, no enhancement of the plasma potential was measured despite 1 MW of coupled ICRF power. When the antenna is powered, energy deposition increases on its four corners and on neighboring limiter tiles magnetically connected to some of those corners. The energy deposited on the antenna and limiter is minimized together with near-field plasma potentials. Additionally, we show that deviation from $P_\mathrm {cent}$/$P_\mathrm {tot} \approx 0.8$ enhances wave-plasma interactions in places not magnetically connected to the antenna. These far-field effects are correlated with changes in the antenna spectrum. Hence, on C-Mod, near-field and far-field interactions were minimized for about the same range of $P_\mathrm {cent}$/$P_\mathrm {tot}$. Optimal power tapering was also found to improve ICRF heating efficiency and facilitate H-mode access. Finally, we show that the heat flux pattern on the toroidally aligned antennas reverses with the direction of the RF-induced E×B flow in front of the antenna, a correlation not observed for the FA antenna. We argue that the RF-induced E×B flow, which carries high-density plasma from the near-SOL, is aligned with the FA antenna and does not intercept its corners, where the plasma potential is large. This could explain the previously reported smaller impurity generation by the FA antenna (Wukitch et al 2013 Phys. Plasmas 20 056117).

Alcator C-Mod↗
DOE OSTI2025

Turbulence simulations of drift-Alfvén wave effects on edge-localized modes and divertor target heat flux width

A series of BOUT++ turbulence simulations are performed for two Pre-Fusion Power Operation (PFPO-1,2) phases of the ITER Research plan proclaimed in 2019. Linear simulation results show that PFPO-1 is unstable to Peeling-ballooning modes (PB), while the PFPO-2 is unstable to the coupling of PB and Drift-Alfvén wave (DAW) instabilities. The linear results are qualitatively consistent with the dispersion relation of DAW. To study the influence of the DAW on the edge-localized mode (ELM) crash, the PFPO-2 is adopted in this section. Different from the grassy ELM in [Li et al 2022 Nucl. Fusion 62, 096030], nonlinear simulations show that the ELM size of PFPO-2 is almost one-third of the grassy ELM, representing a distinct small ELM. However, simulations then show that if the PB instability is removed, the fluctuation amplitude drops by an order of magnitude and the ELM crash disappears, which is in accord with the theory in [Xu et al 2010 Physical Review Letters, Vol. 105, 175005] and the results in [Li et al 2022 Nucl. Fusion 62, 096030], confirming that the PB instability is a necessary condition for an ELM crash. Furthermore, removing the DAW drive also suppresses ELM crashes, implying that PB instability is necessary but insufficient for PFPO-2 ELM and that DAW could amplify PB-driven turbulence. In addition, by integrating results of both PFPO phases by BOUT++ turbulence analysis with heat flux width (λ q ) and electron thermal diffusivity (χ e ), these simulations establish a predictive framework for heat flux width and its dominant mechanisms, thereby providing a comprehensive scheme for the prediction of the heat flux width. Moreover, simulations indicate that DAW driving can increase the transport coefficient by enhancing the turbulent transport, leading to a broadened heat flux width once the transport coefficient exceeds

Drift-Alfvén wave↗
DOE OSTI2026

High-bandwidth frequency domain multiplexed readout of transition-edge sensors for neutrinoless double beta decay searches

The next-generation of cryogenic neutrinoless double-beta decay experiments require increasingly fast readout in order to improve background discrimination. These experiments, operated as cryogenic calorimeters at ∼ 10 mK, are usually read out by high-impedance neutron transmutation doped (NTD) thermistors, which provide good energy resolution, but are limited by ∼ 1 ms response times. Superconducting detectors, such as transition-edge sensors (TESs) with a time resolution of ∼ 100 μs, offer superior timing performance over NTD semiconductor bolometers. To make this technology viable for an application to a thousand or more channels, multiplexed readout is necessary in order to minimize the thermal load and radioactive contamination induced by the readout. Frequency-domain multiplexing readout (fMUX) for TESs, previously developed at Berkeley Lab and McGill University, is currently in use for mm-wave telescopes with detector sampling rates in the order of 100 Hz. We demonstrate a new readout system, based on the McGill/Berkeley digital fMux readout, to satisfy the higher bandwidth and noise requirements of the next generation of TES-instrumented cryogenic calorimeters. Each multiplexing readout module comprises 10 superconducting resonators in the 1–5 MHz range and a DC superconducting quantum interference device (DC-SQUID), interfaced to high-speed field programmable gate array (FPGA)-based electronics for digital signal processing and low-latency SQUID feedback. The new readout samples detectors at 156 kHz, three orders of magnitude faster than its cosmology-oriented predecessor, and demonstrates a stable feedback bandwidth of 3 kHz in a real TES-based system.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Characterization of edge damage induced on REBCO superconducting tape by mechanical slitting

Abstract Rare-earth barium-copper-oxide (REBCO) superconductors are high-field superconductors fabricated in a tape geometry that can be utilized in magnet applications well in excess of 20 T. Due to the multilayer architecture of the tape, delamination is one cause of mechanical failure in REBCO tapes. During a mechanical slitting step in the manufacturing process, edge cracks can be introduced into the tape. These cracks are thought to be potential initiation sites for crack propagation in the tapes when subjected to stresses in the fabrication and operation of magnet systems. We sought to understand which layers were the mechanically weakest by locating the crack initiation layer and identifying the geometrical conditions of the slitter that promoted or suppressed crack formation. The described cracking was investigated by selectively etching and characterizing each layer with scanning electron microscopy, laser confocal microscopy, and digital image analysis. Our analysis showed that the average crack lengths in the REBCO, LaMnO 3 (LMO) and Al 2 O 3 layers were 34 μ m, 28 μ m, and 15 μ m, respectively. The total number of cracks measured in 30 mm of wire length was between 3000 and 5700 depending on the layer and their crack densities were 102 cracks mm −1 for REBCO, 108 cracks mm −1 for LMO, and 183 cracks mm −1 for Al 2 O 3 . These results indicated that there are separate crack initiation mechanisms for the REBCO and the LMO layers, as detailed in the paper. With a better understanding of the crack growth behavior exhibited by REBCO tapes, the fabrication process can be improved to provide a more mechanically stable and cost-effective superconductor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Real-time confinement regime detection in fusion plasmas with convolutional neural networks and high-bandwidth edge fluctuation measurements

Abstract A real-time detection of the plasma confinement regime can enable new advanced plasma control capabilities for both the access to and sustainment of enhanced confinement regimes in fusion devices. For example, a real-time indication of the confinement regime can facilitate transition to the high-performing wide-pedestal (WP) quiescent H-mode, or avoid unwanted transitions to lower confinement regimes that may induce plasma termination. To demonstrate real-time confinement regime detection, we use the 2D beam emission spectroscopy (BES) diagnostic system to capture localized density fluctuations of long wavelength turbulent modes in the edge region at a 1 MHz sampling rate. BES data from 330 discharges in either L-mode, H-mode, quiescent H (QH)-mode, or WP QH-mode were collected from the DIII-D tokamak and curated to develop a high-quality database to train a deep-learning classification model for real-time confinement detection. We utilize the 6×8 spatial configuration with a time window of 1024 µ s and recast the input to obtain spectral-like features via fast Fourier transform preprocessing. We employ a shallow 3D convolutional neural network for the multivariate time-series classification task and utilize a softmax in the final dense layer to retrieve a probability distribution over the different confinement regimes. Our model classifies the global confinement state on 44 unseen test discharges with an average F 1 score of 0.94, using only ∼1 ms snippets of BES data at a time. This activity demonstrates the feasibility for real-time data analysis of fluctuation diagnostics in future devices such as ITER, where the need for reliable and advanced plasma control is urgent.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Wobbly discs – corrugations seen in the dust lanes of edge-on galaxies

ABSTRACT We report the detection of small-scale bending waves, also known as corrugations, in the dust lanes of five nearby edge-on disc galaxies. This phenomenon, where the disc mid-plane bends to become wavy, just as in warps but on a smaller scale, is seen here for the first time, in the dust lanes running across the discs. Because they are seen in absorption, this feature must be present in the dust disc in the outskirts of these galaxies. We enhance the visibility of these features using unsharp masking, trace the dust mid-plane across the disc, measure the corrugation amplitude by eye and the corrugation wavelength using Fourier analysis. The corrugation amplitude is found to be in the range of 70–300pc and the wavelengths lie between 1 and 5 kpc. In this limited sample, we find that the amplitude of the corrugations tends to be larger for lower mass galaxies, whereas the wavelength of corrugation does not seem to depend on the mass of host galaxies. Linear stability analysis is performed to find out the dynamical state of these dust discs. Based on WKB analysis, we find that the dust corrugations in about half of our sample are stable. Further analysis, on a larger sample would be useful to strengthen the above results.

Narayan, Chaitra A.↗
DOE OSTI2022

The distribution of dust in edge-on galaxies: I. The global structure

ABSTRACT In this first paper in a series we present a study of the global dust emission distribution in nearby edge-on spiral galaxies. Our sample consists of 16 angularly large and 13 less spatially resolved galaxies selected from the DustPedia sample. To explore the dust emission distribution, we exploit the Herschel photometry in the range 100–500 $\mu $m. We employ Sérsic and 3D disc models to fit the observed 2D profiles of the galaxies. Both approaches give similar results. Our analysis unequivocally states the case for the presence of extraplanar dust in between 6 and 10 large galaxies. The results reveal that both the disc scale length and height increase as a function of wavelength between 100 and 500 $\mu $m. The dust disc scale height positively correlates with the dust disc scale length, similar to what is observed for the stellar discs. We also find correlations between the scale lengths and scale heights in the near- and far-infrared which suggest that the stellar discs and their dust counterparts are tightly connected. Furthermore, the intrinsic flattening of the dust disc is inversely proportional to the maximum rotation velocity and the dust mass of the galaxy: more massive spiral galaxies host, on average, relatively thinner dust discs. Also, there is a tendency for the dust-to-stellar scale height ratio to decrease with the dust mass and rotation velocity. We conclude that low-mass spiral galaxies host a diffuse, puffed-up dust disc with a thickness similar to that of the stellar disc.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Large-area photon calorimeter with Ir-Pt bilayer transition-edge sensor for the CUPID experiment

CUPID is a next-generation neutrinoless double-β decay experiment that will require cryogenic light detectors to improve background suppression, via the simultaneous readout of heat and light channels from its scintillating crystals. In this work, we showcase light detectors based on an alternative Ir-Pt bilayer transition-edge sensor. We have performed a systematic study to improve the thermal coupling between the photon absorber and the sensor, and thereby its responsivity. Our first devices meet CUPID's baseline noise requirement of < 100 eV rms. Our detectors have risetimes of approximately 180μs and measured timing jitter of < 20μs for the expected signal to noise at the Q value of the decay, which achieves the CUPID's criterion of rejecting two-neutrino double-β decay pile-up events. In conclusion, the current work will inform the fabrication of future devices, culminating in the final TES design and a scaleable readout scheme for CUPID.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Dark counts in optical superconducting transition-edge sensors for rare-event searches

Superconducting transition-edge sensors (TESs) are a type of quantum sensor known for their high single-photon detection efficiency and low background. This makes TESs ideal for particle-physics experiments searching for rare events. In this work, we present a comprehensive characterization of the background in optical TESs, distinguishing three types of events: electrical-noise, high-energy, and photonlike events. We introduce computational methods to automate the classification of events. We experimentally verify and simulate the source of the high-energy events. We also isolate the photonlike events, the expected signal in dielectric haloscopes searching for dark-matter dark photons, and achieve a photonlike dark-count rate of 3.6× 10 − 4 in the 0.8–3.2 eV energy range.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗