Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “configurable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

The characteristics of the ground vortex and its effect on the aerodynamics of the STOL configuration

The interaction of the free stream velocity on the wall jet formed by the impingement of deflected engine thrust results in a rolled up vortex which exerts sizable forces on a short takeoff (STOL) airplane configuration. Some data suggest that the boundary layer under the free stream ahead of the configuration may be important in determining the extent of the travel of the wall jet into the oncoming stream. Here, early studies of the ground vortex are examined, and those results are compared to some later data obtained with moving a model over a fixed ground board. The effect of the ground vortex on the aerodynamic characteristics are discussed.

Stewart, Vearle R.↗

Debris prevention analysis for DFI/OFI/OEI (STS-26 configuration only)

The first 3 shuttle flights to use the Redesigned Solid Rocket Motors (RSRMs) will utilize Development Flight Instrumentation (DFI), as well as Operational Flight Instrumentation (OFI), and Operational Environment Instrumentation (OEI). The OFI consists of high pressure transducers used on both RSRMs to monitor the igniter and motor chamber pressure. DFI consists of assorted strain gages, temperature sensors, accelerometers, girth gages, and low level pressure transducers. The latter are installed on the left hand booster to measure post-separation aerodynamic loading. OEI consistes of temperature sensors. After Flight 3, all DFI gages are to be deleted, and only OFI and OEI will be used for subsequent flights. This report deals specifically with debris prevention and hazards concernig the STS-26 flight DFI configuration only. Continued analysis is being done that will adequately address the debris hazards associated with the STS-27 and subsequent flight DFI configurations.

Richi, Glen A.↗

Robust model-based controller synthesis for the SCOLE configuration

The design of a robust compensator is considered for the SCOLE configuration using a frequency-response shaping technique based on the LQG/LTR algorithm. Results indicate that a tenth-order compensator can be used to meet stability-performance-robustness conditions for a 26th-order SCOLE model without destabilizing spillover effects. Since the SCOLE configuration is representative of many proposed spaceflight experiments, the results and design techniques employed potentially should be applicable to a wide range of large space structure control problems.

Armstrong, E. S.↗

The effects of magnetic nozzle configurations on plasma thrusters

Plasma thrusters have been operated at power levels from 10kW to 0.1MW. When these devices have had magnetic fields applied to them which form a nozzle configuration for the expanding plasma, they have shown marked increases in exhaust velocity which is in direct proportion to the magnitude of the applied field. Further, recent results have shown that electrode erosion may be influenced by applied magnetic fields. This research is directed to the experimental and computational study of the effects of applied magnetic field nozzles in the acceleration of plasma flows. Plasma source devices which eliminate the plasma interaction in normal thrusters are studied as most basic. Normal thruster configurations will be studied without applied fields and with applied magnetic nozzle fields. Unique computational studies will utilize existing codes which accurately include transport processes. Unique diagnostic studies will support the experimental studies to generate new data. Both computation and diagnostics will be combined to indicate the physical mechanisms and transport properties that are operative in order to allow scaling and accurate prediction of thruster performance.

York, Thomas M.↗

The Flying Diamond: A joined aircraft configuration design project, volume 1

The results of the analysis conducted on the Joined Wing Configuration study are presented. The joined wing configuration employs a conventional fuselage and incorporates two wings joined together near their tips to form a diamond shape in both plan view and front view. The arrangement of the lifting surfaces uses the rear wing as a horizontal tail and as a forward wing strut. The rear wing has its root at the tip of the vertical stabilizer and is structurally attached to the trailing edge of the forward wing. This arrangement of the two wings forms a truss structure which is inherently resistant to the aerodynamic bending loads generated during flight. This allows for a considerable reduction in the weight of the lifting surfaces. With smaller internal wing structures needed, the Joined Wing may employ thinner wings which are more suitable for supersonic and hypersonic flight, having less induced drag than conventional cantilever winged aircraft. Inherent in the Joined Wing is the capability of the generation of direct lift and side force which enhance the performance parameters.

Ball, Chris↗

The Horizon: A blended wing aircraft configuration design project, volume 3

The results of a study to design a High-Speed Civilian Transport (HSCT) using the blended wing-body configuration are presented. The HSCT is a Mach 2 to 5 transport aircraft designed to compete with current commercial aircraft. The subjects discussed are sizing, configuration, aerodynamics, stability and control, propulsion, performance, structures and pollution effects.

Keidel, Paul↗

CAP-TSD: A program for unsteady transonic analysis of realistic aircraft configurations

The development of a new transonic code to predict unsteady flows about realistic aircraft configurations are described. An approximate factorization algorithm for solution of the unsteady transonic small disturbance equation is first described. Because of the superior stability characteristics of the AF algorithm, a new transonic aeroelasticity code was developed which is described in some detail. The new code was very easy to modify to include the additional aircraft components, so in a very short period of time the code was developed to treat complete aircraft configurations. Finally, applications are presented which demonstrate many of the geometry capabilities of the new code.

Batina, John T.↗

Euler/Navier-Stokes calculations of transonic flow past fixed- and rotary-wing aircraft configurations

Computational fluid dynamics has an increasingly important role in the design and analysis of aircraft as computer hardware becomes faster and algorithms become more efficient. Progress is being made in two directions: more complex and realistic configurations are being treated and algorithms based on higher approximations to the complete Navier-Stokes equations are being developed. The literature indicates that linear panel methods can model detailed, realistic aircraft geometries in flow regimes where this approximation is valid. As algorithms including higher approximations to the Navier-Stokes equations are developed, computer resource requirements increase rapidly. Generation of suitable grids become more difficult and the number of grid points required to resolve flow features of interest increases. Recently, the development of large vector computers has enabled researchers to attempt more complex geometries with Euler and Navier-Stokes algorithms. The results of calculations for transonic flow about a typical transport and fighter wing-body configuration using thin layer Navier-Stokes equations are described along with flow about helicopter rotor blades using both Euler/Navier-Stokes equations.

Deese, J. E.↗

Experimental Aerodynamic Characteristics of a Joined-wing Research Aircraft Configuration

A wind-tunnel test was conducted at Ames Research Center to measure the aerodynamic characteristics of a joined-wing research aircraft (JWRA). This aircraft was designed to utilize the fuselage and engines of the existing NASA AD-1 aircraft. The JWRA was designed to have removable outer wing panels to represent three different configurations with the interwing joint at different fractions of the wing span. A one-sixth-scale wind-tunnel model of all three configurations of the JWRA was tested in the Ames 12-Foot Pressure Wind Tunnel to measure aerodynamic performance, stability, and control characteristics. The results of these tests are presented. Longitudinal and lateral-directional characteristics were measured over an angle of attack range of -7 to 14 deg and over an angle of sideslip range of -5 to +2.5 deg at a Mach number of 0.35 and a Reynolds number of 2.2x10(6)/ft. Various combinations of deflected control surfaces were tested to measure the effectiveness and impact on stability of several control surface arrangements. In addition, the effects on stall and post-stall aerodynamic characteristics from small leading-edge devices called vortilons were measured. The results of these tests indicate that the JWRA had very good aerodynamic performance and acceptable stability and control throughout its flight envelope. The vortilons produced a profound improvement in the stall and post-stall characteristics with no measurable effects on cruise performance.

Smith, Stephen C.↗

An algebraic homotopy method for generating quasi-three-dimensional grids for high-speed configurations

A fast and versatile procedure for algebraically generating boundary conforming computational grids for use with finite-volume Euler flow solvers is presented. A semi-analytic homotopic procedure is used to generate the grids. Grids generated in two-dimensional planes are stacked to produce quasi-three-dimensional grid systems. The body surface and outer boundary are described in terms of surface parameters. An interpolation scheme is used to blend between the body surface and the outer boundary in order to determine the field points. The method, albeit developed for analytically generated body geometries is equally applicable to other classes of geometries. The method can be used for both internal and external flow configurations, the only constraint being that the body geometries be specified in two-dimensional cross-sections stationed along the longitudinal axis of the configuration. Techniques for controlling various grid parameters, e.g., clustering and orthogonality are described. Techniques for treating problems arising in algebraic grid generation for geometries with sharp corners are addressed. A set of representative grid systems generated by this method is included. Results of flow computations using these grids are presented for validation of the effectiveness of the method.

Moitra, Anutosh↗

Alternate space station freedom configuration considerations to accommodate solar dynamic power

The results of a technical audit of the Space Station Freedom Program conducted by the Program Director was announced in early 1989 and included a proposal to use solar dynamic power generation systems to provide primary electrical energy for orbital flight operations rather than photovoltaic solar array systems. To generate the current program baseline power of 75 kW, two or more solar concentrators approximately 50 feet in diameter would be required to replace four pairs of solar arrays whose rectangular blanket size is approximately 200 feet by 30 feet. The photovoltaic power system concept uses solar arrays to generate electricity that is stored in nickel-hydrogen batteries. The proposed concept uses the solar concentrator dishes to reflect and focus the Sun's energy to heat helium-xenon gas to drive electricity generating turbines. The purpose here is to consider the station configuration issues for incorporation of solar dynamic power system components. Key flight dynamic configuration geometry issues are addressed and an assembly sequence scenario is developed.

Deryder, L. J.↗

V/STOL aircraft configurations and opportunities in the Pacific Basin

Advanced aircraft configurations offer new transportation options for the Pacific Basin. Described is a range of vehicles from low-disk to high-disk loading aircraft, including high-speed rotorcraft, subsonic vertical and short takeoff and landing (V/STOL) aircraft, and subsonic short takeoff and landing (STOL) aircraft. The status and advantages of the various configurations are described. Some of these show promise for satisfying many of the transportation requirements of the Pacific Basin; as such, they could revolutionize short-haul transportation in that region.

Albers, James A.↗

Efficient vibration mode analysis of aircraft with multiple external store configurations

A coupling method for efficient vibration mode analysis of aircraft with multiple external store configurations is presented. A set of low-frequency vibration modes, including rigid-body modes, represent the aircraft. Each external store is represented by its vibration modes with clamped boundary conditions, and by its rigid-body inertial properties. The aircraft modes are obtained from a finite-element model loaded by dummy rigid external stores with fictitious masses. The coupling procedure unloads the dummy stores and loads the actual stores instead. The analytical development is presented, the effects of the fictitious mass magnitudes are discussed, and a numerical example is given for a combat aircraft with external wing stores. Comparison with vibration modes obtained by a direct (full-size) eigensolution shows very accurate coupling results. Once the aircraft and stores data bases are constructed, the computer time for analyzing any external store configuration is two to three orders of magnitude less than that of a direct solution.

Karpel, M.↗

A rule-based systems approach to spacecraft communications configuration optimization

An experimental rule-based system for optimizing user spacecraft communications configurations was developed at NASA to support mission planning for spacecraft that obtain telecommunications services through NASA's Tracking and Data Relay Satellite System. Designated Expert for Communications Configuration Optimization (ECCO), and implemented in the OPS5 production system language, the system has shown the validity of a rule-based systems approach to this optimization problem. The development of ECCO and the incremental optimizatin method on which it is based are discussed. A test case using hypothetical mission data is included to demonstrate the optimization concept.

Rash, James L.↗

A patched-grid algorithm for complex configurations directed towards the F-18 aircraft

A patched-grid algorithm for the analysis of complex configurations with an implicit, upwind-biased Navier-Stokes solver is presented. Results from both a spatial-flux and a time-flux conservation approach to patching across zonal boundaries are presented. A generalized coordinate transformation with a biquadratic geometric element is used at the zonal interface in order to treat highly stretched viscous grids and arbitrarily-shaped zonal boundaries. Applications are made to the F-18 forebody-strake configuration at subsonic, high-alpha conditions. Computed surface flow patterns compare well with ground-based and flight-test results; the large effect of Reynolds number on the forebody flowfield is shown.

Thomas, James L.↗

Pressure and heat transfer investigation of a modified NASP baseline configuration at M = 6

A cooperative NASA Langley-Boeing investigation was conducted in the Langley eight-Foot High Temperature Tunnel to obtain hypersonic pressure and heat transfer data. In this investigation a large scale (1/20), modified version of the National Aero-Space Plane configuration known as the 'Government Baseline' was tested at a nominal Mach number of 6; at two Reynolds numbers (0.6 and 1.6 million per foot); and at angles of attack from about 0 to 15 deg. There were several purposes for the investigation: to provide a windward and leeward pressure and heat transfer data base for a realistic configuration for verification of computational methods, to provide these data for a large-scale model, and to provide these data for true temperature conditions because of concern about data from low temperature tunnels.

Reubush, David E.↗

Launch site payload test configurations for Space Shuttle scientific payloads

This paper provides an overview of the test configurations which are utilized in prelaunch testing at the John F. Kennedy Space Center (KSC) for those scientific payloads which are flown in the National Space Transportation System (NSTS) Space Shuttle. A generalized view of the payload prelaunch processing is provided and the major types of payload configurations are described. The majority of the prelaunch test activity involves the verification of experiment functions, compatibility of experiment-to-carrier interfaces and payload-to-orbiter interfaces. The Shuttle's avionics system is presented as it relates to payloads. The testing of Spacelab experiments and the experiment-to-Spacelab compatibility verification is described as is the test activity for partial payloads and their experiments. Test operations which involve simulated orbiter interface verification and actual payload-to-orbiter testing are discussed. An overview of the Space Station payload processing concept is presented.

Schuiling, Roelof L.↗