Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STRENGTH FUNCTIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Franck-Condon Tuning of Optical Cycling Centers by Organic Functionalization

Laser induced electronic excitations that spontaneously emit photons and decay directly to the initial ground state (“optical cycling transitions”) are used in quantum information and precision measurement for state initialization and readout. To extend this primarily atomic technique to large, organic compounds, we theoretically investigate optical cycling of alkaline earth phenoxides and their functionalized derivatives. We find that optical cycle leakage due to wave function mismatch is low in these species, and can be further suppressed by using chemical substitution to boost the electron-withdrawing strength of the aromatic molecular ligand through resonance and induction effects. This provides a straightforward way to use chemical functional groups to construct optical cycling moieties for laser cooling, state preparation, and quantum measurement.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effective collision strengths for electron impact excitations in S II

Electron impact collision strengths for forbidden, semiforbidden, and allowed transitions in S II calculated using the R-matrix method are presented. Configuration interaction wave functions are used to represent the six target states included in the calculation. At low impact energies the collision strengths are dominated by resonances for several transitions. The contribution from higher partial waves is obtained in the close-coupling approximation with exchange terms omitted. Results are presented for the effective collision strengths over a wide temperature range (5000-150,000 K) of astrophysical interest. The present results for the 4S(0) yields 2P(0) transition are 20-30 percent lower than previous calculations, while for the 4S(0) yields 2D(0) transition they are in good agreement. The results are approximately 30 percent higher than those of Ho and Henry (1983) for the 4S(0) yields 2P(0) transition at 80,000 K, and the difference between the two results increases with decreasing temperatures (under 80,000 K).

Tayal, S. S.↗

Life Limiting Behavior in Interlaminar Shear of Continuous Fiber-Reinforced Ceramic Matrix Composites at Elevated Temperatures

Interlaminar shear strength of four different fiber-reinforced ceramic matrix composites was determined with doublenotch shear test specimens as a function of test rate at elevated temperatures ranging from 1100 to 1316 C in air. Life limiting behavior, represented as interlaminar shear strength degradation with decreasing test rate, was significant for 2-D crossplied SiC/MAS-5 and 2-D plain-woven C/SiC composites, but insignificant for 2-D plain-woven SiC/SiC and 2-D woven Sylramic (Dow Corning, Midland, Michigan) SiC/SiC composites. A phenomenological, power-law delayed failure model was proposed to account for and to quantify the rate dependency of interlaminar shear strength of the composites. Additional stress rupture testing in interlaminar shear was conducted at elevated temperatures to validate the proposed model. The model was in good agreement with SiC/MAS-5 and C/SiC composites, but in poor to reasonable agreement with Sylramic SiC/SiC. Constant shear stress-rate testing was proposed as a possible means of life prediction testing methodology for ceramic matrix composites subjected to interlaminar shear at elevated temperatures when short lifetimes are expected.

Choi, Sung R.↗

First principles assessment of helium trapping in Y{sub 2}TiO{sub 5} in nano-featured ferritic alloys

Nano-scale Y{sub 2}Ti{sub 2}O{sub 7} and Y{sub 2}TiO{sub 5} oxides are the major features that provide high strength and irradiation tolerance in nano-structured ferritic alloys. Here, we employ density functional theory to study helium trapping in Y{sub 2}TiO{sub 5}. The results suggest that helium is more deeply trapped in Y{sub 2}TiO{sub 5} compared to Y{sub 2}Ti{sub 2}O{sub 7}. Helium occupies open channels in Y{sub 2}TiO{sub 5}, where it weakly chemically interacts with neighboring oxygen anions, and results in less volume expansion compared to Y{sub 2}Ti{sub 2}O{sub 7}, reducing strains in the iron matrix. The corresponding helium mobility in these channels is very high. While its ultimate fate is to form oxide/matrix interface bubbles, transient deep trapping of helium in oxides plays a major role in the ability of NFA to manage helium distribution.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Advanced Imaging Techniques in Skull Base Osteomyelitis Due to Malignant Otitis Externa

Purpose of Review: To give an up-to-date overview of the strengths and weaknesses of current imaging modalities in diagnosis and follow-up of skull base osteomyelitis (SBO). Recent Findings: CT and MRI are both used for anatomical imaging, and nuclear techniques aid in functional process imaging. Hybrid techniques PET-CT and PET-MRI are the newest modalities which combine imaging strengths. Summary: No single modality is able to address the scope of SBO. A combination of functional and anatomical imaging is needed, in the case of newly suspected SBO we suggest the use of PET-MRI (T1, T2, T1-FS-GADO, DWI) and separate HRCT for diagnosis and follow-up.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Atomic data and spectral line intensities for Ni XVII

Electron impact collision strengths, energy levels, oscillator strengths, and spontaneous radiative decay rates are calculated for Ni XVII. We include in the calculations the 23 lowest configurations, corresponding to 159 fine-structure levels: 3l3l', 3l4l'', and 3s5l''', with l, l' = s, p, d, l'' = s, p, d, f, and l''' = s, p, d. Collision strengths are calculated at five incident energies for all transitions at varying energies above the threshold of each transition. One additional energy, very close to the threshold of each transition, has also been included. Calculations have been carried out using the Flexible Atomic Code in the distorted wave approximation. Additional calculations have been performed with the University College London suite of codes for comparison. Excitation rate coefficients are calculated as a function of electron temperature by assuming a Maxwellian electron velocity distribution. Using the excitation rate coefficients and the radiative transition rates of the present work, statistical equilibrium equations for level populations are solved at electron densities covering the range of 10{sup 8} - 10{sup 14} cm{sup -3} and at an electron temperature of log T{sub e}(K) = 6.5, corresponding to the maximum abundance of Ni XVII. Spectral line intensities are calculated, and their diagnostic relevance is discussed. This dataset will be made available in the next version of the CHIANTI database.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Microstructural, Corrosion, and Mechanical Characterization of Friction Stir Welded Al 6022-to-ZEK100 Mg Joints

Friction stir welded (FSW) aluminum–magnesium lightweight vehicle joints have gained significant interest due to their high strength-to-weight ratio. In this work, the corrosion resistance of this material is analyzed through electrochemical tests, which include open circuit potential (OCP) inspection and potentiodynamic polarization (PD) scanning. Weight loss measurements tested the corrosion rate of the FSW weld through cyclic corrosion testing (CCT) according to the standard SAEJ 2334. Mechanical properties were also investigated, including lap-shear strength, micro- and nano-hardness mapping, and true stress–strain curves as a function of local processing history. The electrochemical results indicate that the center weld zone’s corrosion property stays between the two base alloys. Indentation-based testing demonstrated that the weld zone behaves differently from base alloys. Lap shear strength surprisingly did not drop much even after eight weeks of cyclic corrosion tests, indicating that the joint did not allow any ingress of the electrolyte.

36 MATERIALS SCIENCE↗

Molecular-Dynamics Analysis of the Mechanical Behavior of Plasma-Facing Tungsten

We report a systematic computational analysis of the mechanical behavior of plasma-facing component (PFC) tungsten focusing on the impact of void and helium (He) bubble defects on the mechanical response beyond the elastic regime. Specifically, we explore the effects of porosity and He atomic fraction on the mechanical properties and structural response of PFC tungsten, at varying temperature and bubble size. We find that the Young modulus of defective tungsten undergoes substantial softening that follows an exponential scaling relation as a function of matrix porosity and He atomic content. Beyond the elastic regime, our high strain rate simulations reveal that the presence of nanoscale spherical defects (empty voids and He bubbles) reduces the yield strength of tungsten in a monotonically decreasing fashion, obeying an exponential scaling relation as a function of tungsten matrix porosity and He concentration. Our detailed analysis of the structural response of PFC tungsten near the yield point reveals that yielding is initiated by emission of dislocation loops from bubble/matrix interfaces, mainly 1/2<111> shear loops, followed by gliding and growth of these loops and reactions to form <100> dislocations. Furthermore, dislocation gliding on the <111>{211} twin systems nucleates 1/6<111> twin regions in the tungsten matrix. These dynamical processes reduce the stress in the matrix substantially. Subsequent dislocation interactions and depletion of the twin phases via nucleation and propagation of detwinning partials lead the tungsten matrix to a next deformation stage characterized by stress increase during applied straining. Furthermore, our structural analysis reveals that the depletion of twin boundaries (areal defects) is strongly impacted by the density of He bubbles at higher porosities. After the initial stress relief upon yielding, increase in the dislocation density in conjunction with decrease in the areal defect density facilitates the initiation of dislocation-driven deformation mechanisms in the PFC crystal.

36 MATERIALS SCIENCE↗

Bifurcation of avoided crossing at an exceptional point in the dispersion of sound and light in locally resonant media

The avoided crossing behavior in the interaction of propagating sound or light waves with resonant inclusions is analyzed using a simple model of an acoustic medium containing damped mass-spring oscillators, which is shown to be equivalent to the Lorentz oscillator model in the elementary dispersion theory in optics. Two classes of experimental situations dictating the choice in the analysis of the dispersion relation are identified. If the wavevector is regarded as the independent variable and frequency as a complex function of the wavevector, then the avoided crossing bifurcates at an exceptional point at a certain value of the parameter γβ -1/2 , where γ and β characterize the oscillator damping and interaction strength, respectively. This behavior is not observed if the wavevector is regarded as a complex function of frequency.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Time-dependent fracture strength of oriented polymers

A statistical consideration based upon a theory of microscopic molecular kinetics is developed to describe the time-dependent fracture process for oriented polymers. The interrelation between the macroscopic fracture strength and the microscopic behaviors is formulated with the aid of a double Fourier series expansion. The microscopic behavior in the vicinity of a point is expressed in the form of a spherical function which can be expanded into a series of symmetric tensorial terms. Subsequently, the fracture strength of polymers is evaluated in terms of both time and molecular orientation. By taking account of the individual values of the directional fraction of integrity, the time to fracture and the most probable direction of fracture within any volume element in a medium are predicted.

Mun, M. S.↗

Effect of Free Jet on Refraction and Noise

This article investigates the role of a free jet on the sound radiated from a jet. In particular, the role of an infinite wind tunnel, which simulates the forward flight condition, is compared to that of a finite wind tunnel. The second configuration is usually used in experiments, where the microphones are located in a static ambient medium far outside the free jet. To study the effect of the free jet on noise, both propagation and source strength need to be addressed. In this work, the exact Green's function in a locally parallel flow is derived for a simulated flight case. Numerical examples are presented that show a reduction in the magnitude of the Green's function in the aft arc and an increase in the forward arc for the simulated flight condition. The effect of finite wind tunnel on refraction is sensitive to the source location and is most pronounced in the aft arc. A Reynolds-averaged Navier-Stokes solution (RANS) yields the required mean flow and turbulence scales that are used in the jet mixing noise spectrum calculations. In addition to the sound/flow interaction, the separate effect of source strength and elongation of the noise-generating region of the jet in a forward flight is studied. Comparisons are made with experiments for the static and finite tunnel cases. Finally, the standard free-jet shear corrections that convert the finite wind tunnel measurements to an ideal wind tunnel arrangement are evaluated.

Khavaran, Abbas↗

Responsivity calibration of the LoWEUS spectrometer

We performed an in situ calibration of the relative responsivity function of the Long-Wavelength Extreme Ultraviolet Spectrometer (LoWEUS), while operating on the Lithium Tokamak Experiment (LTX) at Princeton Plasma Physics Laboratory. The calibration was accomplished by measuring oxygen lines, which are typically present in LTX plasmas. The measured spectral line intensities of each oxygen charge state were then compared to the calculated emission strengths given in the CHIANTI atomic database. Normalizing the strongest line in each charge state to the CHIANTI predictions, we obtained the differences between the measured and predicted values for the relative strengths of the other lines of a given charge state. We find that a 3rd degree polynomial function provides a good fit to the data points. Our measurements show that the responsivity between about 120 and 300 Å varies by factor of ∼30.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A Composite Modeling Analysis of the Deformation Behavior of Medium Manganese Steels

The deformation behavior of medium manganese steels was evaluated with uniaxial tensile testing and the results were correlated with predictions of a composite model shown previously to provide design insight into the development of multi-phase steels with third-generation advanced high strength steel (3GAHSS) properties. An equilibrium thermodynamic-based methodology to design microstructures containing systematic amounts of metastable austenite with controlled stability against transformation is presented. The analysis is based on Mn enrichment of austenite during intercritical annealing of medium Mn (7 and 10 wt pct.) low carbon (0.1 and 0.15 wt pct) steels. The steels were produced as laboratory heats that were hot and cold rolled prior to annealing. After annealing the microstructures consisted primarily of either a matrix of fine grained ferrite with austenite contents between 32.6 and 45.2 wt pct (7Mn, 0.1C steels) or a matrix of martensite with various amounts of austenite in the higher Mn steel. The different intercritical annealing conditions produced steels with wide variations in austenite contents and austenite compositions (Mn and C contents) resulting in steels with significant variations in austenite stability. Predictions based on the composite analysis with different assumed flow behaviors for the individual constituents and stability functions for the meta-stable austenite are presented and shown to accurately predict strength-ductility combinations over a range of austenite volume fractions for the 7Mn steel. Applicability of the composite analysis is extended to consider the deformation behavior of the 10Mn steel and evaluate other possible microstructural combinations leading to 3GAHSS properties.

36 MATERIALS SCIENCE↗

Two-body weak currents in heavy nuclei

In light and medium-mass nuclei, two-body weak currents from chiral effective field theory account for a significant portion of the phenomenological quenching of Gamow-Teller transition matrix elements. Here we examine the systematic effects of two-body axial currents on Gamow-Teller strength and β-decay rates in heavy nuclei within energy-density functional theory. Using a Skyrme functional and the charge-changing finite amplitude method, we add the contributions of two-body currents to the usual one-body linear response in the Gamow-Teller channel, both exactly and though a densitymatrix expansion. The two-body currents, as expected, usually quench both summed Gamow-Teller strength and decay rates, but by an amount that decreases as the neutron excess grows. They can enhance individual low-lying transitions, however, leading to decay rates that are quite different from those that an energy-independent quenching would produce, particularly in neutron-rich nuclei. We show that both these effects are related to changes in the total nucleon density as the number of neutrons increases.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Rapid Bayesian High Entropy Alloy Designs Fabricated via Wire Arc Additive Manufacturing

Purpose: This project seeks to demonstrate a new high-throughput (rapid) alloy design technique applied to creating new high entropy alloys (HEAs) for extreme environments. High entropy alloys shift the design paradigm from being focused on a single principal element (e.g. nickel-based alloys) to target alloys that include high atomic fractions (X >10%) of multiple elements. These HEA materials can exhibit sluggish diffusion and enhanced corrosion resistance, ideal for potential applications in advanced ultra supercritical (A-USC) steam cycles for power generation. Scope: The addition of multiple elements in high atomic fractions creates an enormous design space that cannot easily be investigated by traditional material design strategies such as designed of experiments (DOE). This project utilizes a Bayesian machine learning algorithm that has been modified to work with calculation of phase diagrams (CALPHAD) software. This Bayesian algorithm reduces manual inputs and increase the likelihood of achieving an optimal solution. Compositional inputs to this algorithm will be assessed using existing material property models for high temperature strength and corrosion resistance. The target for alloy performance will be a 15% (~100 ⁰C) increase in allowable service temperature beyond heat-resistant stainless steels while maintaining or improving alloy cost and corrosion resistance. Haynes 230 was selected as a baseline, which is 57 wt% Ni with 22 wt% Cr 14 wt% W, and 2 wt% Mo as solid solution strengtheners. In addition to rapid design via Bayesian machine learning, the alloys were rapidly fabricated using a multi-wire arc additive manufacturing (mWAAM) technique which allows for precise control of alloy composition and assessing of alloy design “windows” to study composition effects. Build speeds for wire-arc additive processes are among the highest for additive technologies enabling rapid and reliable sample fabrication when compared to conventional methods such as arc button melting. The mWAAM samples will be rapidly characterized via instrumented indentation for room temperature modulus and strength and for elevated temperature strength via hot hardness tests. After being screened with hardness testing, potential alloys will be further evaluated with conventional microscopy techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM) to assess agreement with modeling results. The most promising compositions will also be evaluated by printing full sized tensile specimens for mechanical behavior tests at elevated temperatures. Results: Bayesian machine learning of a single performance function was initially used to optimize five performance metrics: 1) single phase stability, 2) yield strength, 3) creep resistance (low diffusion coefficient), 4) freezing range (weldability), and 5) material cost. The single performance function was suboptimal as assumptions had to be made about the results while formulating the optimization. A goal-oriented Bayesian optimization strategy (Hanaoka, 2021) was implemented with CALPHAD for use with the five metrics above. This multi-objective Bayesian optimization (MOBO) enabled the design of NiCrCoFe alloys with V and W additions. A base composition of NiCoCr was selected as Ni provides a stable FCC matrix, Cr aids corrosion/oxidation resistance, and Co is a solid-solutions strengthener that also improves creep by increasing the activation energy. Fe helps reduce diffusion coefficients and cost. Finally, V and W were selected for their reasonable solubility and high atomic misfit to aid in solid solution strengthening. Cracking of the mWAAM specimens was an early issue, and the Easton solidification cracking model (Easton et al., 2014a) was selected for addition to the MOBO function. High performing alloys fabricated by mWAAM included Ni 28 Cr 25 Co 26 Fe 15 V 8 and Ni 62 Cr 18 Co 1 Fe 3 W 15 . It was observed that even after adapting the mWAAM process for W, the W did not fully dissolve. To fully evaluate the Ni 62 Cr 18 Co 1 Fe 3 W 15 composition, a cored wire (80-20 NiCr sheath/powder core) was manufactured and printed via WAAM, and HIP’ing was utilized to homogenize and densify the printed alloy. The V and W alloys produced met metrics 1 (solid solution), 4 (solidification cracking), and 5 (cost). However, an unmodeled mechanism of thermal stress cracking was identified in the WAAM produced materials, perhaps exacerbated by the lack of grain boundary strengthening elements (B, C). Conclusions & Recommendations: A high-throughput (rapid) alloy design technique was applied to designing and manufacturing new high entropy alloys (HEAs) for extreme environments utilizing MOBO and mWAAM. The developed process was rapid and effective in addressing the mechanisms included in the model. The lack of grain boundary strengthening element additions (e.g., B, C) was a simplification that likely produced thermal stress cracking that turned into a large part of the investigation. Additions on the order of 0.005 wt% B and 0.05 wt% C likely would have minimized thermal stress grain boundary cracking. Overall, the high throughput design strategy is promising for rapid design of metrics-driven alloys for advanced ultra supercritical (A-USC) steam cycles for power generation. The MOBO and mWAAM process could be commercialized to accelerate metrics-driven alloy design. In addition, the cored-wire process utilized for scale-up is a promising high-volume process for WAAM alloy development and scale-up.

36 MATERIALS SCIENCE↗

Predicting the time-temperature dependent axial failure of B/A1 composites

Experimental and theoretical studies were conducted in order to understand and predict the effects of time, temperature, and stress on the axial failure modes of boron fibers and B/A1 composites. Due to the anelastic nature of boron fiber deformation, it was possible to determine simple creep functions which can be employed to accurately describe creep and fracture stress of as-produced fibers. Analysis of damping and strength data for B/6061 A1 composites indicates that fiber creep effects of creep on fiber fracture are measurably reduced by the composite fabrication process. The creep function appropriate for fibers with B/Al composites was also determined. A fracture theory is presented for predicting the time-temperature dependence of the axial tensile strength for metal matrix composites in general and B/A1 composites in particular.

Dicarlo, J. A.↗

The low-lying 2-sigma-minus states of OH

The configuration-interaction method is used to determine the electronic wave functions of the two lowest 2-sigma-minus states of OH using four different atomic orbital basis sets. Potential energy curves, transition moments, oscillator strengths, and photodissociation cross sections are obtained. Electronic transition dipole moments connecting the excited 1 2-sigma-minus and 2(D)2-sigma-minus states with each other and with the ground chi-2-pi state are presented as functions of internuclear distance. The theoretical absorption oscillator strengths for the D-2-sigma-minus(v prime = 0) from chi-2-pi(v double prime = 0) transition are in good agreement with the empirical value derived from astronomical measurement. The photodissociation cross sections for absorption from the v prime = 0, 1, and 2 levels of the ground state into the continuum of the 1 2-sigma-minus state are calculated, and the interstellar and cometary photodissociation rates are derived.

Van Dishoeck, E. F.↗

Ground-state properties of the one-dimensional attractive Hubbard model with confinement: A comparative study

We revisit the one-dimensional attractive Hubbard model by using the Bethe-ansatz-based density-functional theory and density-matrix renormalization method. The ground-state properties of this model are discussed in details for different fillings and different confining conditions in weak-to-intermediate coupling regime. We investigate the ground-state energy, energy gap, and pair-binding energy and compare them with those calculated from the canonical Bardeen-Cooper-Schrieffer approximation. We find that the Bethe-ansatz-based density-functional theory is computationally easy and yields an accurate description of the ground-state properties for weak-to-intermediate interaction strength, different fillings, and confinements. In order to characterize the quantum phase transition in the presence of a harmonic confinement, we calculate the thermodynamic stiffness, the density-functional fidelity, and fidelity susceptibility, respectively. It is shown that with the increase in the number of particles or attractive interaction strength, the system can be driven from the Luther-Emery-type phase to the composite phase of Luther-Emery-type in the wings and insulatinglike in the center.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗