Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Dynamic data acquisition, reduction, and analysis for the identification of high-speed compressor component post-stability characteristics

A compressor test was conducted in which transient data were obtained for the purpose of identifying the high-speed post-stability characteristics. The transient, surge-cycle nature of high-speed post-stability operation precludes the possibility of obtaining the characteristics in a steady-state manner, as is possible during low-speed poststability operation, which is characterized by quasi-steady rotating-stall behavior. Specialized compressor instrumentation was developed and was used to obtain the necessary surge-cycle performance data, which were then digitized, filtered, and analyzed. The high-speed post-stability characteristics were obtained through the use of a maximum likelihood-parameter estimation technique. The estimated characteristics were found to be insensitive to the presence of measurement noise and unmodelled system dynamics, but the compressor time-response constants, which were also estimated, were more sensitive to these same disturbances.

Dvorak, S. D.↗

Enhancing compressor distortion tolerance by asymmetric stator control

This paper describes a preliminary study of a method for increasing compressor tolerance in circumferential distortion through asymmetric vane stagger control. The changes in vane stagger about the circumference are used to increase compressor pressure rise and flow capability over part of the annulus and decrease these over the rest. The average pressure rise and flow thus remain roughly constant but the velocity distortion is reduced (and can even be made zero). Calculations are carried out to show the magnitude of the vane motions that must be used, and it is found that significant increases in distoriton attenuation can be achieved with realistic vane swings. In addition, the asymmetric vane stagger scheme leads to a substantial decrease in stall pressure rise loss due to inlet total pressure distortion. This type of control strategy appears worthy of further investigation, both theoretical and experimental.

Chen, G. T.↗

The effect of neutrino transport on the collapse of iron stellar cores

A multigroup flux-limited diffusion approximation to neutrino transport, correct to first order in material velocities, is described. The role of neutrino-electron scattering in determining core deleptonization is studied using a modified Fokker-Planck approximation in which adjacent neutrino energy groups are coupled. The moderate deleptonizaton obtained during infall restricts homologous core masses to less than 0.8 solar mass. With 0.6-0.8 solar mass of outer core to traverse, nuclear dissociation alone stalls the shock waves produced at core bounce. In addition, neutrino energy losses remove at least another 4 x 10 to the 51st ergs. In no case is matter ejected promptly as a direct result of the initial shock wave.

Myra, E. S.↗

A review of research in rotor loads

The research accomplished in the area of rotor loads over the last 13 to 14 years is reviewed. The start of the period examined is defined by the 1973 AGARD Milan conference and the 1974 hypothetical rotor comparison. The major emphasis of the review is research performed by the U.S. Army and NASA at their laboratories and/or by the industry under government contract. For the purpose of this review, two main topics are addressed: rotor loads prediction and means of rotor loads reduction. A limited discussion of research in gust loads and maneuver loads is included. In the area of rotor loads predictions, the major problem areas are reviewed including dynamic stall, wake induced flows, blade tip effects, fuselage induced effects, blade structural modeling, hub impedance, and solution methods. It is concluded that the capability to predict rotor loads has not significantly improved in this time frame. Future progress will require more extensive correlation of measurements and predictions to better understand the causes of the problems, and a recognition that differences between theory and measurement have multiple sources, yet must be treated as a whole. There is a need for high-quality data to support future research in rotor loads, but the resulting data base must not be seen as an end in itself. It will be useful only if it is integrated into firm long-range plans for the use of the data.

Bousman, William G.↗

Development of drive mechanism for an oscillating airfoil

The design and development of an in-draft wind tunnel test section which will be used to study the dynamic stall of airfoils oscillating in pitch is described. The hardware developed comprises a spanned airfoil between schleiren windows, a four bar linkage, flywheels, a drive system and a test section structure.

Sticht, Clifford D.↗

Two gimbal bearing case studies: Some lessons learned

Two troublesome, torque related problems associated with gimbal actuators are discussed. Large, thin section angular contact bearings can have a surprisingly high torque sensitivity to radial thermal gradients. A predictive thermal-mechanical bearing analysis, as described, was helpful in establishing a safe temperature operating envelope. In the second example, end-of-travel torque limits of an oscillatory gimbal bearing appoached motor stall during limit cycling life tests. Bearing modifications required to restore acceptable torque performance are described. The lessons learned from these case studies should benefit designers of precision gimbals where singular bearing torque related problems are not uncommon.

Loewenthal, Stuart H.↗

Acoustic characteristics of 1/20-scale model helicopter rotors

A wind tunnel test to study the effects of geometric scale on acoustics and to investigate the applicability of very small scale models for the study of acoustic characteristics of helicopter rotors was conducted in the United Technologies Research Center Acoustic Research Tunnel. The results show that the Reynolds number effects significantly alter the Blade-Vortex-Interaction (BVI) Noise characteristics by enhancing the lower frequency content and suppressing the higher frequency content. In the time domain this is observed as an inverted thickness noise impulse rather than the typical positive-negative impulse of BVI noise. At higher advance ratio conditions, in the absence of BVI, the 1/20 scale model acoustic trends with Mach number follow those of larger scale models. However, the 1/20 scale model acoustic trends appear to indicate stall at higher thrust and advance ratio conditions.

Shenoy, Rajarama K.↗

Preliminary aerodynamic design considerations for advanced laminar flow aircraft configurations

Modern composite manufacturing methods have provided the opportunity for smooth surfaces that can sustain large regions of natural laminar flow (NLF) boundary layer behavior and have stimulated interest in developing advanced NLF airfoils and improved aircraft designs. Some of the preliminary results obtained in exploratory research investigations on advanced aircraft configurations at the NASA Langley Research Center are discussed. Results of the initial studies have shown that the aerodynamic effects of configuration variables such as canard/wing arrangements, airfoils, and pusher-type and tractor-type propeller installations can be particularly significant at high angles of attack. Flow field interactions between aircraft components were shown to produce undesirable aerodynamic effects on a wing behind a heavily loaded canard, and the use of properly designed wing leading-edge modifications, such as a leading-edge droop, offset the undesirable aerodynamic effects by delaying wing stall and providing increased stall/spin resistance with minimum degradation of laminar flow behavior.

Johnson, Joseph L., Jr.↗

Natural laminar flow and airplane stability and control

Location and mode of transition from laminar to turbulent boundary layer flow have a dominant effect on the aerodynamic characteristics of an airfoil section. The influences of these parameters on the sectional lift and drag characteristics of three airfoils are examined. Both analytical and experimental results demonstrate that when the boundary layer transitions near the leading edge as a result of surface roughness, extensive trailing-edge separation of the turbulent boundary layer may occur. If the airfoil has a relatively sharp leading-edge, leading-edge stall due to laminar separation can occur after the leading-edge suction peak is formed. These two-dimensional results are used to examine the effects of boundary layer transition behavior on airplane longitudinal and lateral-directional stability and control.

Vandam, Cornelis P.↗

Augmentor performance of an F100 engine model derivative engine in an F-15 airplane

The transient performance of the F100 engine model derivative (EMD) augmentor was evaluated in an F-15 airplane. The augmentor was a newly designed 16-segment augmentor. It was tested with a segment-1 sprayring with 90 deg fuel injection, and later with a modified segment-1 sprayring with centerline fuel injection. With the 90 deg injection, no-lights occurred at high altitudes with airspeeds of 175 knots or less; however, the results were better than when using the standard F100-PW-100 engine. With the centerline fuel injection, all transients were successful to an altitude of 15,500 meters and an airspeed of 150 knots: no failures to light, blowouts, or stalls occurred. For a first flight evaluation, the augmentor transient performance was excellent.

Walton, James T.↗

Low-speed wind-tunnel test of a STOL supersonic-cruise fighter concept

A wind-tunnel investigation was conducted to examine the low-speed static stability and control characteristics of a 0.10 scale model of a STOL supersonic cruise fighter concept. The concept, referred to as a twin boom fighter, was designed as a STOL aircraft capable of efficient long range supersonic cruise. The configuration name is derived from the long twin booms extending aft of the engine to the twin vertical tails which support a high center horizontal tail. The propulsion system features a two dimensional thrust vectoring exhaust nozzle which is located so that the nozzle hinge line is near the aircraft center of gravity. This arrangement is intended to allow large thrust vector angles to be used to obtain significant values of powered lift, while minimizing pitching moment trim changes. Low speed stability and control information was obtained over an angle of attack range including the stall. A study of jet induced power effects was included.

Coe, Paul L., Jr.↗

A comparison of the various helicopter mathematical models used in the methodology assessment

Various features of the computer codes used in the helicopter industry and by government agencies for rotorcraft aeroelastic stability analysis are compared. Mathematical rigor in modeling rotorcraft is given primarily to the rotor-system dynamic behavior; the aerodynamic modeling is still limited to strip theory and to uneven application of corrections for stall, reversed flow, yawed flow, radial flow, and unsteady aerodynamic effects. The forward-flight regime analysis is included in five of the 11 codes surveyed. However, only two of these codes are capable of a Floquet analysis for aeroelastic stability. For the hover regime, nine of the 11 codes use eigen-analysis approach. The remaining codes perform a harmonic analysis of the transient response of system.

Stephens, Wendell B.↗

An experimental investigation of two 15 percent-scale wind tunnel fan-blade designs

An experimental 3-D investigation of two fan-blade designs was conducted. The fan blades tested were 15 percent-scale models of blades to be used in the fan drive of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center. NACA 65- and modified NACA 65-series sections incorporated increased thickness on the upper surface, between the leading edge and the one-half-chord position. Twist and taper were the same for both blade designs. The fan blades with modified 65-series sections were found to have an increased stall margin when they were compared with the unmodified blades.

Signor, David B.↗

Collapse of 9 solar mass stars

General relativistic hydrodynamical calculations of the collapse of O + Ne + Mg cores of a 9 solar mass star are reported. Collapse is induced by rapid electron captures as the O + Ne + Mg is burned to nuclear statistical equilibrium. The high entropy in the core after burning leads to a large abundance of free protons which readily capture electrons. This leads to large neutrino losses and a correspondingly small infalling homologous core. The hydrodynamic shock thus forms at a small mass point. The shock stalls before reaching the edge of the O + Ne + Mg core and thereby fails to produce a successful supernova explosion by the direct mechanism. No enhancement in the shock energy due to nuclear burning is found.

Baron, E.↗

Collapsing white dwarfs

The results of the hydrodynamic collapse of an accreting C + O white dwarf are presented. Collapse is induced by electron captures in the iron core behind a conductive deflagration front. The shock wave produced by the hydrodynamic bounce of the iron core stalls at about 115 km, and thus a neutron star formed in such a model would be formed as an optically quiet event.

Baron, E.↗

Measurements of the unsteady flow field within the stator row of a transonic axial-flow fan. II - Results and discussion

Unsteady velocity field measurements made within the stator row of a transonic axial-flow fan are presented. Measurements were obtained at midspan for two different stator blade rows using a laser anemometer. The first stator row consists of double circular-arc airfoils with a solidity of 1.68. The second features controlled-diffusion airfoils with a solidity of 0.85. Both were tested at design-speed peak efficiency conditions. In addition, the controlled-diffusion stator was also tested at near stall conditions. The procedures developed here are used to identify the rotor wake generated and unresolved unsteadiness from the velocity measurements (rotor wake generated unsteadiness refers to the unsteadiness generated by the rotor wake velocity deficit and unresolved unsteadiness refers to all remaining unsteadiness which contributes to the spread in the distribution of velocities such as vortex shedding, turbulence, etc.). Auto and cross correlations of these unsteady velocity fluctuations are presented to show their relative magnitude and spatial distributions. Amplification and attenuation of both rotor wake generated and unresolved unsteadiness are shown to occur within the stator blade passage.

Hathaway, M. D.↗

Application of a comprehensive analytical model of rotorcraft aerodynamics and dynamics (CAMRAD) to the McDonnell Douglas AH-64A helicopter

CAMRAD results on main rotor blade natural frequency and structural loads predictions are compared to flight test data and predictions of the Dynamic Analysis Research Tool (DART) and the Rotor/Airframe Comprehensive Aeroelastic Program (RACAP). Consideration is also given to the effects of various analytical options available in CAMRAD including dynamic stall, wake modeling, and the number of bending and torsion degrees of freedom included in the structural analysis. It is concluded that, while several modeling limitations are identified in the CAMRAD structural analyses, the structural loads predictions are as accurate as analysis codes which provide more representative models of the complex geometries and structures of the AH-64A rotor system. However, it is noted that the CAMRAD analysis cannot be considered fully reliable for dynamic predictions for more advanced bearingless rotor designs being proposed for future AH-64 configurations.

Callahan, C.↗