SEARCH · Engineering Papers

Results for “SIMULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Initial piloted simulation study of geared flap control for tilt-wing V/STOL aircraft

A simulation study of a representative tilt wing transport aircraft was conducted in 1990 on the Ames Vertical Motion Simulator. This simulation is in response to renewed interest in the tilt wing concept for use in future military and civil applications. For past tilt wing concepts, pitch control in hover and low-speed flight has required a tail rotor or reaction jets at the tail. Use of mono cyclic propellers or a geared flap have also been proposed as alternate methods for providing pitch control at low speed. The geared flap is a subject of this current study. This report describes the geared flap concept, the tilt wing aircraft, the simulation model, the simulation facility and experiment setup, the pilots' evaluation tasks and procedures, and the results obtained from the simulation experiment. The pilot evaluations and comments are also documented in the report appendix.

Guerrero, Lourdes M.↗

NASA NTRS1992

SEDS1 mission software verification using a signal simulator

The first flight of the Small Expendable Deployer System (SEDS1) is schedule to fly as the secondary payload of a Delta 2 in March, 1993. The objective of the SEDS1 mission is to collect data to validate the concept of tethered satellite systems and to verify computer simulations used to predict their behavior. SEDS1 will deploy a 50 lb. instrumented satellite as an end mass using a 20 km tether. Langley Research Center is providing the end mass instrumentation, while the Marshall Space Flight Center is designing and building the deployer. The objective of the experiment is to test the SEDS design concept by demonstrating that the system will satisfactorily deploy the full 20 km tether without stopping prematurely, come to a smooth stop on the application of a brake, and cut the tether at the proper time after it swings to the local vertical. Also, SEDS1 will collect data which will be used to test the accuracy of tether dynamics models used to stimulate this type of deployment. The experiment will last about 1.5 hours and complete approximately 1.5 orbits. Radar tracking of the Delta II and end mass is planned. In addition, the SEDS1 on-board computer will continuously record, store, and transmit mission data over the Delta II S-band telemetry system. The Data System will count tether windings as the tether unwinds, log the times of each turn and other mission events, monitor tether tension, and record the temperature of system components. A summary of the measurements taken during the SEDS1 are shown. The Data System will also control the tether brake and cutter mechanisms. Preliminary versions of two major sections of the flight software, the data telemetry modules and the data collection modules, were developed and tested under the 1990 NASA/ASEE Summer Faculty Fellowship Program. To facilitate the debugging of these software modules, a prototype SEDS Data System was programmed to simulate turn count signals. During the 1991 summer program, the concept of simulating signals produced by the SEDS electronics systems and circuits was expanded and more precisely defined. During the 1992 summer program, the SEDS signal simulator was programmed to test the requirements of the SEDS Mission software, and this simulator will be used in the formal verification of the SEDS Mission Software. The formal test procedures specification was written which incorporates the use of the signal simulator to test the SEDS Mission Software and which incorporates procedures for testing the other major component of the SEDS software, the Monitor Software.

Pierson, William E.↗

NASA NTRS1992

Flight simulator for hypersonic vehicle and a study of NASP handling qualities

The research goal of the Human-Machine Systems Engineering Group was to study the existing handling quality studies in aircraft with sonic to supersonic speeds and power in order to understand information requirements needed for a hypersonic vehicle flight simulator. This goal falls within the NASA task statements: (1) develop flight simulator for hypersonic vehicle; (2) study NASP handling qualities; and (3) study effects of flexibility on handling qualities and on control system performance. Following the above statement of work, the group has developed three research strategies. These are: (1) to study existing handling quality studies and the associated aircraft and develop flight simulation data characterization; (2) to develop a profile for flight simulation data acquisition based on objective statement no. 1 above; and (3) to develop a simulator and an embedded expert system platform which can be used in handling quality experiments for hypersonic aircraft/flight simulation training.

Ntuen, Celestine A.↗

NASA NTRS1992

Comparison of simulated and actual wind shear radar data products

Prior to the development of the NASA experimental wind shear radar system, extensive computer simulations were conducted to determine the performance of the radar in combined weather and ground clutter environments. The simulation of the radar used analytical microburst models to determine weather returns and synthetic aperture radar (SAR) maps to determine ground clutter returns. These simulations were used to guide the development of hazard detection algorithms and to predict their performance. The structure of the radar simulation is reviewed. Actual flight data results from the Orlando and Denver tests are compared with simulated results. Areas of agreement and disagreement of actual and simulated results are shown.

Britt, Charles L.↗

NASA NTRS1991

Simulation models for autonomous rendezvous and capture

Autonomous rendezvous and capture (AR&C) is a critical space technology with significant application to a variety of missions. Martin Marietta Astronautics Group (MMAG) has been developing AR&C technical capability in support of several recent NASA contracts. The use of AR&C for the Mars Rover/Sample Return (MRSR) mission was studied through a contract with JSC. Incorporation of AR&C in the Space Transportation Vehicle (STV) lunar mission was studied through a contract with MSFC. The MMAG has also been developing AR&C simulation capability under independent research and development studies. Simulation development was driven by two goals: comprehensive software simulation of the autonomous rendezvous and capture mission from launch to final capture; and integration of the overall software and hardware simulation to support an AR&C flight demonstration. This presentation will highlight the AR&C software simulation tools and analyze results from their application to the STV lunar mission. Plans for an integrated software and hardware simulation will also be summarized.

Smith, Nick G.↗

NASA NTRS1993

Gas turbine system simulation: An object-oriented approach

A prototype gas turbine engine simulation has been developed that offers a generalized framework for the simulation of engines subject to steady-state and transient operating conditions. The prototype is in preliminary form, but it successfully demonstrates the viability of an object-oriented approach for generalized simulation applications. Although object oriented programming languages are-relative to FORTRAN-somewhat austere, it is proposed that gas turbine simulations of an interdisciplinary nature will benefit significantly in terms of code reliability, maintainability, and manageability. This report elucidates specific gas turbine simulation obstacles that an object-oriented framework can overcome and describes the opportunity for interdisciplinary simulation that the approach offers.

Drummond, Colin K.↗

NASA NTRS1993

Implementation of interconnect simulation tools in spice

Accurate computer simulation of high speed digital computer circuits and communication circuits requires a multimode approach to simulate both the devices and the interconnects between devices. Classical circuit analysis algorithms (lumped parameter) are needed for circuit devices and the network formed by the interconnected devices. The interconnects, however, have to be modeled as transmission lines which incorporate electromagnetic field analysis. An approach to writing a multimode simulator is to take an existing software package which performs either lumped parameter analysis or field analysis and add the missing type of analysis routines to the package. In this work a traditionally lumped parameter simulator, SPICE, is modified so that it will perform lossy transmission line analysis using a different model approach. Modifying SPICE3E2 or any other large software package is not a trivial task. An understanding of the programming conventions used, simulation software, and simulation algorithms is required. This thesis was written to clarify the procedure for installing a device into SPICE3E2. The installation of three devices is documented and the installations of the first two provide a foundation for installation of the lossy line which is the third device. The details of discussions are specific to SPICE, but the concepts will be helpful when performing installations into other circuit analysis packages.

Satsangi, H.↗

NASA NTRS1992

Flight Testing and Simulation of an F-15 Airplane Using Throttles for Flight Control

Flight tests and simulation studies using the throttles of an F-15 airplane for emergency flight control have been conducted at the NASA Dryden Flight Research Facility. The airplane and the simulation are capable of extended up-and-away flight, using only throttles for flightpath control. Initial simulation results showed that runway landings using manual throttles only control were difficult, but possible with practice. Manual approaches flown in the airplane were much more difficult, indicating a significant discrepancy between flight and simulation. Analysis of flight data and development of improved simulation models that resolve the discrepancy are discussed. An augmented throttles-only control system that controls bank angle and flightpath with appropriate feedback parameters has also been developed, evaluated in simulations, and is planned for flight in the F-15.

Flight Testing↗

NASA NTRS1992

Rapid development of the X-31 simulation to support flight-testing

The X-31 Enhanced Fighter Maneuverability Program has been recognized to form the International Test Organization, with the NASA Dryden Flight Research Facility (NASA-Dryden) as the responsible test organization. The two X-31 research aircraft and engineering support personnel were colocated at NASA-Dryden, with flight test operations beginning in Apr. 1992. Therefore, rapid development of a hardware-in-the-loop simulation was needed to support the flight test operations at NASA-Dryden, and to perform verification and validation of flight control software. The X-31 simulation system requirements, distributed simulation system architecture, simulation components math models to the visual system, and the advanced capabilities the X-31 simulation provides. In addition, unique software tools and the methods used to rapidly develop this simulation system will be highlighted.

Mackall, Dale↗

NASA NTRS1992

Infrared, microwave, and spaceborne radar simulations of a deep convective system using a 3-D cloud ensemble method

A 3D cloud model is used to simulate the storm structure, and the results are linked to microwave and infrared radiative transfer models for simulation of aircraft observations. Spaceborne radar data are also simulated along the aircraft flight track. The cloud and radiative model simulations are studied and compared with aircraft observations. The initial results indicate that the 3D cloud model is capable of simulating the major features of observed storm systems when given a representative atmospheric sounding to initialize the convective systems. The simulations of infrared and microwave radiances provide reasonably good comparisons with the observations.

Yeh, H.-Y. M.↗

NASA NTRS1993

Simulated rarefied aerodynamics of the Magellan spacecraft during aerobraking

Aerodynamic loads upon the Magellan spacecraft during aerobraking through the atmosphere of Venus are computed at off-design attitudes with a direct simulation Monte Carlo (DSMC) particle method. Simulated rarefied flows at nominal altitudes near 140 km and an entry speed of 8.6 km/s were compared to simulated and analytic free molecular results. Aerodynamic moments, forces, and heating for rarefied entry at all attitudes were 7-10 percent below free molecular results. All moments acted to restore the vehicle to its nominal zero-pitch, zero-yaw attitude. Suggested canting of the solar panels is an innovative configuration to assess gas-surface interaction during aerobraking. The resulting roll torques about the central body-axis as predicted in rarefied flow simulations were nearly twice that predicted for free molecular flow, although differences became less distinct for thermal accommodation coefficients well below unity. Roll torques increased dramatically with reduced accommodation coefficients employed in the simulation. In the DSMC code, periodic free-molecule boundary conditions and a coarse computational grid and body resolution served to minimize the simulation size and cost while retaining solution validity.

Haas, Brian L.↗

NASA NTRS1993

A comparison of regional isentropic-sigma and sigma model simulations of the January 1979 Chicago blizzard

In an initial effort in regional numerical weather prediction, results from the University of Wisconsin isentropic-sigma (UW theta-sigma) hybrid model and an 'identical' sigma model are compared. The two main objectives are to demonstrate the capability of the UW theta-sigma model for regional numerical weather prediction and to identify advantages of the hybrid model in simulating atmospheric water vapor transport and precipitation relative to the sigma model. The 72-h simulations produced by the two models extend over a region covering the western Pacific Ocean, North America, and the western Atlantic Ocean. The simulations begin at 0000 UTC 13 January 1979, a period during which an intense Chicago blizzard develops over the central United States. This period also includes the rapid development of a cyclone in the western Pacific Ocean. Results using the Global Weather Experiment (GWE) ECMWF level IIIB data as initial and verification data indicate that both models produce reasonable and similar 72-h simulations, with the UW theta-sigma model mass and momentum distributions being slightly more accurate than the sigma model. Of particular importance for the Chicago blizzard is that the UW theta-sigma model more accurately simulates water vapor transport northward from the Gulf of Mexico and westward from the Atlantic Ocean. As a result, the hybrid model more accurately simulates observed precipitation, especially over the northeastern U.S. and southeastern Canada.

Zapotocny, Tom H.↗

NASA NTRS1989

Numerical simulation of controlled large space structures

Large Space Structures do not have much damping, which necessitates the installation of a controller onto the structure. If the controller is improperly designed, the structure may become unstable and be destroyed. Since Large Space Structures are extremely expensive pieces of hardware, new controllers must not be tested first on the structure. They must first be tested in computer simulations. Until now, the usual procedure for simulating controlled Large Space Structures is to compute a reduced order modal representation of the structure and then apply the controller. However, this procedure entails modal truncation error. A new software package which is free from this error is currently under development within the Center for Space Construction. The more accurate finite element representation of the structure is used in the simulation, instead of the less accurate reduced order modal representation. This software also features an efficient matrix storage scheme, which effectively deals with the asymmetric system matrices which occur when control is added to the structure. Also, an integration algorithm was chosen so that the simulation is a reliable indicator of system stability or instability. The software package is fairly general in nature. Linearity of the finite element model and of the controller is the only assumption made. Actuator dynamics, sensor dynamics, noise, and disturbances can be handled by the package. In addition, output feedback of displacement, velocity, and/or acceleration signals can be simulated. Kalman state estimation was also implemented. This software was tested on a finite element model of a real Large Space Structure: The Mini-Mast Truss. Mini-Mast is a testbed at NASA-Langley which is currently under development. A 714 degree of freedom finite element model was computed, and a 19 state controller was designed for it. Torque wheel dynamics were added to the model, and the entire closed loop system was simulated with the software package.

Quan, Ralph↗

NASA NTRS1993

Parallel spatial direct numerical simulations on the Intel iPSC/860 hypercube

The implementation and performance of a parallel spatial direct numerical simulation (PSDNS) approach on the Intel iPSC/860 hypercube is documented. The direct numerical simulation approach is used to compute spatially evolving disturbances associated with the laminar-to-turbulent transition in boundary-layer flows. The feasibility of using the PSDNS on the hypercube to perform transition studies is examined. The results indicate that the direct numerical simulation approach can effectively be parallelized on a distributed-memory parallel machine. By increasing the number of processors nearly ideal linear speedups are achieved with nonoptimized routines; slower than linear speedups are achieved with optimized (machine dependent library) routines. This slower than linear speedup results because the Fast Fourier Transform (FFT) routine dominates the computational cost and because the routine indicates less than ideal speedups. However with the machine-dependent routines the total computational cost decreases by a factor of 4 to 5 compared with standard FORTRAN routines. The computational cost increases linearly with spanwise wall-normal and streamwise grid refinements. The hypercube with 32 processors was estimated to require approximately twice the amount of Cray supercomputer single processor time to complete a comparable simulation; however it is estimated that a subgrid-scale model which reduces the required number of grid points and becomes a large-eddy simulation (PSLES) would reduce the computational cost and memory requirements by a factor of 10 over the PSDNS. This PSLES implementation would enable transition simulations on the hypercube at a reasonable computational cost.

Joslin, Ronald D.↗

NASA NTRS1993

Meso-Beta scale numerical simulation studies of terrain-induced jet streak mass/momentum perturbations

The Control-B simulation experiment was designed to improve on the Control-A experiment performed with the GMASS model. This experiment addressed several inadequacies with the first smooth terrain numerical simulation by including: (1) increased nested-grid resolution to better define the simulated gravity waves, (2) increased horizontal diffusion to remove outflow boundary condition noise, and (3) the use of reanalyzed rawinsonde data and surface observations in the initial state to increase the definition of the observed jet streak as well as other low-level features. A smoothed-terrain dry simulation with the nested-grid GMASS model has revealed many important aspects of the processes which resulted in the generation of gravity waves in the region and time when and where they were observed. However, the vertical structure, number, and characteristics of the waves are still quite different from observed waves as diagnosed thus necessitating future improved simulations. However, this control simulation has produced substantial insight into processes which occur on many spatial scales over a 30 hour time period thus allowing one to draw promising inferences as to the mechanisms for the complex process which occurred in nature during the CCOPE case study. The theoretical aspects of the project have focus on understanding the nature of the ageostrophic circulations which are produced in idealized models of the atmosphere in which the troposphere is modeled in one of two ways. The first model assumes that the lower atmosphere can be represented as a single layer of homogeneous fluid whose upper surface is free to exhibit vertical displacement. Two-dimensional internal convergence (divergence) occurring during the adjustment to an asymptotic equilibrium state from an ageostrophic initial state whose momentum structure is representative of a midlatitude localized zonal wind anomaly will cause the free upper surface of the homogeneous atmosphere to rise (fall), and therefore the response can be viewed as being physically three-dimensional. The second model assumes that the troposphere can be represented by an unbounded continuously stratified Boussinesq fluid of constant Brunt-Vaisala frequency N, where the vertical gradient of the basic state potential temperature profile allows for the existence of vertically propagating internal inertia-gravity waves.

Lin, Yuh-Lang↗

NASA NTRS1993

Solar simulator for solar dynamic space power system testing

Planned vacuum tank testing of a solar dynamic space power system requires a solar simulator. Several solar simulators were previously built and used for vacuum tank testing of various space systems. However, the apparent solar subtense angle, i.e., the angular size of the apparent sun as viewed from the experiment, of these solar simulators is too large to enable testing of solar dynamic systems. A new design was developed to satisfy the requirements of the solar dynamic testing. This design provides 1.8 kW/m(sup 2) onto a 4.5M diameter test area from a source that subtends only 1 deg, full cone angle. Key features that enable this improved performance are (1) elimination of the collimating mirror commonly used in solar simulators to transform the diverging beam into a parallel beam; (2) a redesigned lamp module that has increased efficiency; and (3) the use of a segmented reflective surface to combine beams from several individual lamp modules at the pseudosun. Each segment of this reflective surface has complex curvature to control the distribution of light. By developing a new solar simulator design for testing of the solar dynamic system instead of modifying current designs, the initial cost was cut in half, the efficiency was increased by 50 percent reducing the operating costs by one-third, and the volume occupied by the solar simulator was reduced by a factor of 10.

Jefferies, Kent S.↗

NASA NTRS1993

CFD simulation of coaxial injectors

The development of improved performance models for the Space Shuttle Main Engine (SSME) is an important, ongoing program at NASA MSFC. These models allow prediction of overall system performance, as well as analysis of run-time anomalies which might adversely affect engine performance or safety. Due to the complexity of the flow fields associated with the SSME, NASA has increasingly turned to Computational Fluid Dynamics (CFD) techniques as modeling tools. An important component of the SSME system is the fuel preburner, which consists of a cylindrical chamber with a plate containing 264 coaxial injector elements at one end. A fuel rich mixture of gaseous hydrogen and liquid oxygen is injected and combusted in the chamber. This process preheats the hydrogen fuel before it enters the main combustion chamber, powers the hydrogen turbo-pump, and provides a heat dump for nozzle cooling. Issues of interest include the temperature and pressure fields at the turbine inlet and the thermal compatibility between the preburner chamber and injector plate. Performance anomalies can occur due to incomplete combustion, blocked injector ports, etc. The performance model should include the capability to simulate the effects of these anomalies. The current approach to the numerical simulation of the SSME fuel preburner flow field is to use a global model based on the MSFC sponsored FNDS code. This code does not have the capabilities of modeling several aspects of the problem such as detailed modeling of the coaxial injectors. Therefore, an effort has been initiated to develop a detailed simulation of the preburner coaxial injectors and provide gas phase boundary conditions just downstream of the injector face as input to the FDNS code. This simulation should include three-dimensional geometric effects such as proximity of injectors to baffles and chamber walls and interaction between injectors. This report describes an investigation into the numerical simulation of GH2/LOX coaxial injectors. The following sections will discuss the physical aspects of injectors, the CFD code employed, and preliminary results of a simulation of a single coaxial injector for which experimental data is available. It is hoped that this work will lay the foundation for the development of a unique and useful tool to support the SSME program.

Landrum, D. Brian↗

NASA NTRS1993

Integration and evaluation of a simulator designed to be used within a dynamic prototyping environment

The human computer interface (HCI) prototyping environment is designed to allow developers to rapidly prototype systems so that the interface and functionality of a system can be evaluated and iteratively refined early in the development process. This keeps development costs down by modifying the interface during the requirements definition phase, thus minimizing changes that need to be made during and after flight code development. Problems occur within a system when the user interface is not adequately developed and when designers and developers have an incomplete understanding of the system requirements. A process has been developed for prototyping on-board payload displays for Space Station Freedom. This prototyping process consists of five phases: identification of known requirements, analysis of the requirements, development of a formal design representation and specification, development of the prototype, and evaluation of the prototype. The actual development of the prototype involves prototyping the displays, developing a low fidelity simulator, building of an interface (or communication) between the displays and the simulator, integration of these components, and testing to ensure that the interface does what the developer expects. This research integrates and evaluates a software tool which has been developed to serve as a simulator within the prototyping environment. The tool is being evaluated to determine whether or not it meets the basic requirements which are needed for a low fidelity simulator within this environment. In order to evaluate the architecture and its components, a human computer interface for and a simulator of an automobile have been developed as a prototype. The individual components (i.e., the interface and simulator) have been developed, and the current research was designed to integrate and test the complete working system within the prototyping environment. The following sections will describe the architecture and components of the rapid prototyping environment, the development of a system to assess the environment, and the integration and evaluation of PERCNET.

Moore, Loretta A.↗