Results for “Propulsion” — Page 90

NASA NTRSDate not supplied

Heat Pipe Heat Exchanger for Nuclear Electric Propulsion Power Conversion System

Heat pipe reactors have been considered by the Space Nuclear Propulsion program for Nuclear Electric Propulsion (NEP) power conversion systems and will require the use of heat exchangers to transfer heat via heat pipes to the Brayton working fluid from the reactor. Sodium (Na) and lithium (Li) were considered as viable working fluids inside the heat pipes which were assumed to have the same geometry based on studies and information from the Los Alamos National Laboratory. The heat exchanger was assumed to be a rectangular duct with heat pipes serving as tubes from previous NEP work and recommendations. Based on this geometry, Zukauskas correlations were used to model the convective heat transfer and pressure losses. Parametric sizing of the reactor component involved operational limits-based heat pipe thermal hydraulic modeling in cohesion with required user input geometry for the in-core lattice and various subcomponents. This work considered various power conversion inlet temperatures (PCIT) of 1100 K, 1150 K, and 1200 K for Na heat pipes and 1100 K, 1150 K, 1200 K, and 1400 K for Li heat pipes based on recommendations from prior work. Using these different PCITs, the subsystem masses and pressure losses were determined and analyzed. Na showed a lower overall operating temperature and about a fifth of the maximum heat throughput capability than that of Li for the same geometry. Due to this, the entire Na-based subsystem ended up being three times more massive than the Li-based subsystem given five times the required number of heat pipes. At the low PCIT of 1100 K, the Na-based subsystem exhibited the lowest pressure losses given the large overall cross sectional flow area and relatively low frictional pressure losses. However, as the PCIT increased, the frictional pressure losses increased resulting in higher pressure losses at the 1200 K PCIT than Li-based subsystem. However, the Li-based subsystem exhibited the largest pressure losses of all analyzed cases at the 1400 K PCIT due to the low density of the Brayton working fluid at this temperature.

electric↗

NASA NTRSDate not supplied

Thermal Vacuum Chamber Demonstration of a Cryocooled, HTS Rotor for a 1.4 MW Electric Machine for Electrified Aircraft Propulsion

Aircraft with electrified propulsion systems require electric machines that are very lightweight and highly efficient. Advancements to the state of the art are required to meet this demand. This is particularly true for large transport aircraft with more than about 150 passengers, which will require electric machines with power ratings in the 1 to 30+ MW range. At this scale of power, superconducting technology becomes attractive for electrified aircraft propulsion to increase efficiency and reduce mass [1]. A mass reduction relative to non-superconducting machines can result from an increase in the specific power of the machine and indirectly through a significant reduction in the amount of waste heat generated on the aircraft, which reduces the mass of the thermal management system [2]. NASA’s high efficiency megawatt motor (HEMM) is a 1.4 MW partially superconducting machine that is being developed to achieve an efficiency greater than 98% and electromagnetic specific power greater than 16 kW/kg. HEMM contains a copper stator operating at an average temperature around 423 K and a superconducting rotor composed of no-insulation 2nd generation high temperature superconducting (HTS) coils that operates around 60 K. The superconducting coils are conductively cooled by a pulse tube cryocooler embedded inside and rotating with the rotor shaft. This paper presents a full-scale demonstration of the rotor in a thermal vacuum chamber at the designed operating temperature. The test was designed to validate the design of HEMM’s rotor, namely the ability to operate the 2G HTS coils at their rated direct current in a relevant thermal environment while being conductively cooled.

high temperature superconductors↗

NASA NTRSDate not supplied

Ideas for Infusing In-Space Servicing, Assembly, and Manufacturing Concepts into Nuclear Electric Propulsion Architectures

NASA is currently investigating nuclear electric propulsion (NEP) for human Mars transport within the space nuclear propulsion portfolio. NEP spacecraft have the following characteristics, they: 1) include very large structures (~100-meter length); 2) are comprised of many components/modules; and 3) have very long lifetimes (e.g., 50 years for fuel rods). Thus, NEP spacecraft can be classified as a “persistent asset,” which is any zero-g or planetary surface system that benefits from in-space assembly (ISA) or multiple visits for servicing, repairs, and upgrades. NEP spacecraft will benefit from taking advantage of, and incorporating, In-space Servicing, Assembly, and Manufacturing (ISAM) capabilities in the spacecraft architecture from the onset, enabling system maintenance, repair, and evolution. ISA has a long history of being proposed for, and studied as, a means for achieving large systems in space. More recently, the benefits of ISA have been recognized by NASA, the Department of Defense (DOD), other government agencies, and commercial space companies, and thus, ISAM is being actively pursued at a national level. Past and current strategies for achieving large structures in space have relied largely on two strategies; the first is to launch monolithic structures (designed to meet launch vehicle requirements for payload size and mass) that are docked or berthed to other monolithic structures on-orbit to form a larger structure (e.g., the International Space Station [ISS]); the second is folding and packaging large structures to fit inside a payload fairing and deploying the full-sized structure (unaided) once on-orbit (e.g., the James Webb Space Telescope [JWST]). To date, conceptual architecture studies performed for NEP spacecraft capable of human-rated Mars transport have only included a combination of the two previously mentioned strategies. This paper will propose ideas for infusing ISAM strategies into NEP vehicle architectures that leverage existing and near future technologies and enable the resulting NEP systems to be realized in a more time- and cost-efficient manner.

in-space assembly↗

NASA NTRSDate not supplied

Hybrid-Electric Aero-Propulsion Controls Testbed Results

NASA is supporting the development of Electrified Aircraft Propulsion (EAP) technology due to its potential to reduce aircraft fuel burn, emissions, and noise as well as improving safety and performance. One focus of this research is the electrification of conventional turbomachinery propulsion systems, which offers ways to improve the performance and operability of turbine-engine powered aircraft through the addition of electro-mechanical systems. These hybrid-electric turbine engines provide additional actuation and energy management control opportunities for improving stability and transient response behavior. This paper summarizes the results of a Hardware-in-the-Loop (HIL) test performed at the NASA Electric Aircraft Testbed (NEAT) during the summer of 2022. The test demonstrates the feasibility and performance of an advanced energy management control strategy by integrating a simulated turbofan engine with scaled electro-mechanical hardware. A full-scale real-time reference model of a geared turbofan was run alongside a scaled electro-mechanical system representing the electrified turbofan components operating at a megawatt-scale power level. The model was interfaced with the hardware through a novel closed-loop control and scaling algorithm that emulated the dynamic speed and torque response of the turbofan shafts. The control strategy was implemented on the electrical machines connected to the emulated turbomachinery shafts. The results from the testbed are compared against simulations that predict the testbed and geared turbofan model operation. The energy management control strategy successfully changed the operating point of the engine model and improved its stability during throttle transients. These results also demonstrate the success of the novel closed loop control and scaling approach for emulating turbomachinery and elevate the Technology Readiness Level (TRL) of the energy management control strategy.

Aeronautics↗

NASA NTRSDate not supplied

ENABLING ARCHITECTURE TRADES AND DESIGN EXPLORATION FOR NUCLEAR ELECTRIC PROPULSION

Recent renewed interest in Nuclear Electric Propulsion (NEP) at NASA has driven the need for design space exploration and analysis of alternative architectures to evaluate performance and feasibility of NEP concepts. It has been over a decade since NASA last invested in Nuclear Electric Propulsion development efforts, and the landscape has shifted in both mission objectives and technology readiness levels. This also means that many of the engineering analyses and design frameworks tailored to NEP date back to the Jupiter Icy Moons Orbiter (JIMO) days of the early 2000s. Thus, a need was identified for updating and modernizing the modeling and simulation toolsets for NEP. This paper will detail the development efforts in the Marshall Space Flight Center’s Advanced Concepts Office, with a particular focus on the development of the NEP stage of the NEP-Chem vehicle. The paper will cover the various models used, and their current development status, as well as provide an overview of the integrated vehicle model and plans for further development.

Nuclear↗

NASA NTRSDate not supplied

Propulsion-Airframe Integration for Conceptual Redesign of a Low-Boom Supersonic Transport

A low-boom supersonic transport was designed for a cruise Mach of 1.7 and 40 passengers. This low-boom aircraft, referred to as the Mach 1.7 40-PAX concept, was generated using computational fluid dynamics (CFD) based sonic boom analysis at the start of overland cruise (SOC). The engine for the Mach 1.7 40-PAX concept was designed using the Numerical Propulsion System Simulation (NPSS) and modeled as a flow-through nacelle for CFD analysis. To understand how the engine plume affects the undertrack ground signature, the Mach 1.7 40-PAX concept is redesigned using an aeropropulsive CFD simulation. A process is developed for approximation of the NPSS engine at SOC by a CFD engine for aeropropulsive CFD simulation. The generated CFD engine has the identical nozzle boundary conditions and approximately the same mass flow and thrust as those of the NPSS engine at SOC. Then, the configuration with the CFD engines is optimized to approximately restore the low-boom characteristics of the Mach 1.7 40-PAX concept. Finally, the CFD simulation data for the optimized concept with the CFD engines is used to calibrate the low-fidelity aerodynamic analyses for mission analysis of this concept. The cyclic dependency of the involved disciplinary analyses is resolved using an iteration method for a consistent coupling of the mission analysis, NPSS engine analysis, and low-boom redesign using the aeropropulsive CFD simulation. This low-boom redesign study is used as an example to demonstrate how the propulsion-airframe integration could be implemented for conceptual design of low-boom supersonic transports.

Low-boom supersonic transport↗

NASA NTRSDate not supplied

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas Turbine↗

NASA NTRS2023

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas turbine↗

NASA NTRSDate not supplied

Propulsion-Airframe Integration for Conceptual Redesign of a Low-Boom Supersonic Transport

A low-boom supersonic transport was designed for a cruise Mach of 1.7 and 40 passengers. This low-boom aircraft, referred to as the Mach 1.7 40-PAX concept, was generated using computational fluid dynamics (CFD) based sonic boom analysis at the start of overland cruise (SOC). The engine for the Mach 1.7 40-PAX concept was designed using the Numerical Propulsion System Simulation (NPSS) and modeled as a flow-through nacelle for CFD analysis. To understand how the engine plume affects the undertrack ground signature, the Mach 1.7 40-PAX concept is redesigned using an aeropropulsive CFD simulation. A process for approximation of the NPSS engine at SOC by a CFD engine is developed. The generated CFD engine has the identical nozzle boundary conditions and approximately the same mass flow and thrust as those of the NPSS engine at SOC. Then, the configuration with the CFD engines is optimized to approximately restore the low-boom characteristics of the Mach 1.7 40-PAX concept. Finally, the CFD simulation data for the optimized concept with the CFD engines is used to calibrate the low-fidelity aerodynamic analyses for mission analysis of this concept. The cyclic dependency of the involved disciplinary analyses is resolved using an iteration method for a consistent coupling of the mission analysis, NPSS engine analysis, and low-boom redesign using the aeropropulsive CFD simulation. This low-boom redesign study is used as an example to demonstrate how the propulsion-airframe integration could be implemented for conceptual design of low-boom supersonic transports.

Low-boom supersonic transport↗

NASA NTRSDate not supplied

Nuclear Thermal Propulsion Material Trade for Additively Manufactured Regenerative Chambers

Nuclear thermal propulsion (NTP) is a game changing technology with advantages over chemical propulsion systems for deep space missions but comes with many engineering challenges. This paper focuses on the challenge of material selection for a regeneratively-cooled chamber for use in a nuclear environment with minimal design margins. Chemical compatibility with reactants and products following energy extraction (be it through combustion or neutron bombardment) must be considered. Similarly, mechanical and thermophysical properties (e.g., density, thermal conductivity, yield strength, etc.) as functions of temperature are critical. While hydrogen embrittlement environment (HEE) is a risk and consideration for traditional chemical combustion chambers, application in a nuclear thermal engine adds additional material compatibility and resilience requirements to long-term nuclear radiation exposure. Chamber materials in this trade included, but were not limited to, A-286, Haynes 230, Haynes 282, CRES 347, GRCop-42, GRCop-84, Inconel 625, JBK-75, and NASA HR-1. The material trade focuses on modern additive manufacturing techniques and hypothetical geometric constraints.

Nuclear Thermal Propulsion↗

NASA NTRSDate not supplied

Enabling Architecture Trades and Design Exploration for Nuclear Electric Propulsion

Recent renewed interest in Nuclear Electric Propulsion (NEP) at NASA has driven the need for design space exploration and analysis of alternative architectures to evaluate performance and feasibility of NEP concepts. It has been over a decade since NASA last invested in Nuclear Electric Propulsion development efforts, and the landscape has shifted in both mission objectives and technology readiness levels. This also means that many of the engineering analyses and design frameworks tailored to NEP date back to the Jupiter Icy Moons Orbiter (JIMO) days of the early 2000s. Thus, a need was identified for updating and modernizing the modeling and simulation toolsets for NEP. This paper will detail the development efforts in the Marshall Space Flight Center’s Advanced Concepts Office, with a particular focus on the development of the NEP stage of the NEP-Chem vehicle. The paper will cover the various models used, and their current development status, as well as provide an overview of the integrated vehicle model and plans for further development.

Nuclear↗

NASA NTRSDate not supplied

Nuclear Thermal Propulsion Material Trade for Additively Manufactured Regenerative Chambers

Nuclear thermal propulsion (NTP) is a game changing technology with advantages over chemical propulsion systems for deep space missions but comes with many engineering challenges. This paper focuses on the challenge of material selection for a regeneratively-cooled chamber for use in a nuclear environment with minimal design margins. Chemical compatibility with reactants and products following energy extraction (be it through combustion or neutron bombardment) must be considered. Similarly, mechanical and thermophysical properties (e.g., density, thermal conductivity, yield strength, etc.) as functions of temperature are critical. While hydrogen embrittlement environment (HEE) is a risk and consideration for traditional chemical combustion chambers, application in a nuclear thermal engine adds additional material compatibility and resilience requirements to long-term nuclear radiation exposure. Chamber materials in this trade included, but were not limited to, A-286, Haynes 230, Haynes 282, CRES 347, GRCop-42, GRCop-84, Inconel 625, JBK-75, and NASA HR-1. The material trade focuses on modern additive manufacturing techniques and hypothetical geometric constraints.

Nuclear Thermal Propulsion↗

NASA NTRSDate not supplied

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas turbine↗

NASA NTRSDate not supplied

The Challenges with Material Interfaces in a Nuclear Thermal Propulsion Engine Heat Exchanger

Nuclear Thermal Propulsion (NTP) technology is an enabling technology to send humans to Mars and for agile cis-lunar mobility. NTP systems operate by flowing a propellent through a nuclear reactor. The resulting heated propellent is expulsed through a nozzle to create thrust. A key component in an NTP engine is the heat exchange tubes located within the nuclear reactor. The heat exchange tubes must be able to operate structurally at temperatures up to 2900 K. Carbon-Carbon is a potential material choice for the heat exchange tubes as the material maintains structural integrity at high temperatures. To achieve desired propulsion performance, NTP engines operate at extreme temperatures. In the extreme environment, differences in material coefficients of thermal expansion must be taken into account to avoid potential reduction of engine performance or system failure. Identified potential problems and proposed solutions to material interface challenges in the material interfaces of the heat exchange tubes are discussed, along with lessons learned for future work on NTP engine designs.

Nuclear Thermal Propulsion↗

NASA NTRSDate not supplied

Reactor Parametric Assessments for Alternative Propellant Nuclear Thermal Propulsion Engines

This work focuses on the implications of alternative working fluids for nuclear thermal propulsion (NTP) reactors. To perform this analysis, NASA’s Testing Reference Design (TRD) is altered using parametric studies with selected alternative propellants to determine the reactor modifications required to enable an operable system. This research investigates ammonia, water, methane, helium, and enriched diborane as feasible options to enable a specific impulse (𝐼 𝑠𝑝 ) greater than the chemical propulsion alternatives. Frozen and dissociated 𝐼 𝑠𝑝 for each propellant is shown for variable chamber temperature conditions. Geometrical sensitivities are performed to observe the impact on the neutron multiplication factor (k eff ), system mass, and HALEU loading. Control drum worth curves are included for 5- degree increments of rotation. The base TRD configuration does not enable a critical system for ammonia and enriched diborane, thus these propellants will be highlighted in the final results. Equivalent study results for hydrogen will be included as a point of comparison to the performance of the other options.

Nuclear Thermal Propulsion↗

NASA NTRSDate not supplied

Additive Manufacturing of ZrC for Nuclear Thermal Propulsion Applications

Looking into the future, we are seeing that nuclear is becoming a more and more viable fuel source for space applications due to it being one of the safest energy forms, low greenhouse gas emissions, and inexpensive maintenance. National Aeronautics and Space Administration (NASA) and a few others are looking at nuclear fuels in relation to space travel, specifically in the form of Nuclear Thermal Propulsion (NTP) [1]. NTP provides the answer for space travel to Mars where chemical rockets would not complete the job. A concept art of what these spacecrafts could look like is shown (Figure 1). Uranium Carbide fuel has been chosen to heat a liquid propellant for propulsion. The complex fuel geometries required by space reactors can be achieved by novel techniques fairly easily, cheaply, and safely. In this specific study, we are looking at using Zirconium Carbide (ZrC) to use as a surrogate for Uranium Carbide (UC) due to their similar behaviors under high temperatures. An ink made with ZrC will be made and will be extruded into unique, complex geometries. This is a great starting point to test additive manufacturing on these ceramics.

Additive Manufacturing↗

NASA NTRSDate not supplied

Reactor Parametric Assessments for Alternative Propellant Nuclear Thermal Propulsion Engines

This work focuses on the implications of alternative working fluids for nuclear thermal propulsion (NTP) reactors. To perform this analysis, NASA’s Testing Reference Design (TRD) is altered using parametric studies with selected alternative propellants to determine the reactor modifications required to enable an operable system. This research investigates ammonia, water, methane, helium, and enriched diborane as feasible options to enable a specific impulse (Isp) greater than the chemical propulsion alternatives. Frozen and dissociated Isp for each propellant is shown for variable chamber temperature conditions. Geometrical sensitivities are performed to observe the impact on the neutron multiplication factor (keff), system mass, and HALEU loading. Control drum worth curves are included for 5- degree increments of rotation. The base TRD configuration does not enable a critical system for ammonia and enriched diborane, thus these propellants will be highlighted in the final results. Equivalent study results for hydrogen will be included as a point of comparison to the performance of the other options.

Nuclear Thermal Propulsion↗

NASA NTRSDate not supplied

The Challenges with Material Interfaces in a Nuclear Thermal Propulsion Engine Heat Exchanger

Nuclear Thermal Propulsion (NTP) technology is an enabling technology to send humans to Mars and for agile cis-lunar mobility. NTP systems operate by flowing a propellent through a nuclear reactor. The resulting heated propellent is expulsed through a nozzle to create thrust. A key component in an NTP engine is the heat exchange tubes located within the nuclear reactor. The heat exchange tubes must be able to operate structurally at temperatures up to 2900 K. Carbon-Carbon is a potential material choice for the heat exchange tubes as the material maintains structural integrity at high temperatures. To achieve desired propulsion performance, NTP engines operate at extreme temperatures. In the extreme environment, differences in material coefficients of thermal expansion must be taken into account to avoid potential reduction of engine performance or system failure. Identified potential problems and proposed solutions to material interface challenges in the material interfaces of the heat exchange tubes are discussed, along with lessons learned for future work on NTP engine designs.

Nuclear Thermal Propulsion↗