Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Plutonium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Subcritical Benchmark of the BeRP Ball Reflected by Tungsten

In September 2012, eight subcritical configurations were measured with the clad a-phase plutonium sphere known as the Beryllium-Reflected Plutonium (BeRP) ball at the National Criticality Experiments Research Center (NCERC). The configurations had varying tungsten thicknesses including: 0 (bare), 0.5, 1.0, 1.5, 2.0, 2.5, 2.75, and 3.0 inches. Measurements were conducted to provide subcritical benchmark data. This work includes measured and simulated results from the International Handbook of Evaluated Criticality Safety Benchmark Experiments (ICSBEP) evaluation. (authors)

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Material Balance Area Design for the Transuranic Fuel Cycle Employing High Temperature Gas Cooled Reactors

A major impetus has been to ensure safety in nuclear power plant systems from the beginning of its development to the current period of nuclear renaissance. As one of the next generation reactors with a high level of nuclear safety, high temperature gas cooled reactor (HTGR) has attracted large attention because of the possibility to shut down the reactor safely and remove decay heat without the use of active cooling. A deep-burn concept of fuel utilization is proposed and studied for HTGRs to alleviate plutonium proliferation concern. The idea is to utilize the plutonium extracted by reprocessing the light water reactor (LWR) spent fuel and discharge it only at higher fuel burn-ups of up to 90 atom %. In addition HTGRs have been studied to utilize transuranic (TRU) fuel. A large amount of special nuclear material (SNM) will be used in the HTGR advanced fuel cycle. The inherent proliferation resistance and material attractiveness of the fresh fuel and discharged spent fuel have been discussed against the diversion from peaceful to military uses. On the other hand safeguards of SNM is also important to prevent nuclear proliferation under the Non-Proliferation Treaty between the state and International Atomic Energy Agency (IAEA). Facility operators are responsible to design material balance area (MBA) and provide enough information on material balance of SNMs for the safeguards conclusion. The material unaccounted for (MUF) and measurement uncertainty in MUF (σ{sub MUF}) represent accuracy of material balance. The MBAs have to be designed and established to achieve enough confidence level on MUF and σ{sub MUF}. The MBA design is challenging for nuclear facilities managing large amount of bulk (instead of items) SNM because of potentially large MUF and σ{sub MUF}. A concept and guidance of MBA design for uranium fueled HTGRs has been discussed. In this study, a MBA design is presented for the transuranic fuel cycle employing HTGRs. The MUF and the σ{sub MUF} is calculated and evaluated using international target values (ITVs) provided by the IAEA. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal Testing of Waste Packages for a Storage Environment

The Pipe Overpack Container (POC) was developed at Rocky Flats to transport plutonium residues with higher levels of plutonium than standard TRU waste to the Waste Isolation Pilot Plant (WIPP) for disposal. The POC consists of an inner Pipe Container (PC) surrounded by organic fiber dunnage inside of a 7A drum. The PC was design to maintain separation of fissile material and to provide shielding from radiation. The POC has many design features that are similar to Type B packages that do provide protection from engulfing fires. However, it was not specifically designed to prevent release of stored material during a long-duration fire. POCs are now being used to store combustible TRU waste at Department of Energy (DOE) sites (e.g., Waste Isolation Pilot Plant). Radioactive waste storage operators would like to be able to claim some level of protection is provided by the POCs for thermal assaults that could occur within storage facilities when these POCs contain PCs with combustibles. In 1997 Sandia National Laboratories (SNL) conducted a series of tests to determine the degree of protection POCs provide during storage accident events. One of these tests exposed four of the POCs to a 30-minute engulfing pool fire, resulting in one of the 7A drums generating sufficient internal pressure to pop off its lid and expose the top of the PC to the fire environment. However, these tests are not bounding for POC/PC containing combustibles. With the addition of combustible materials in the PC, the possibility exists for generation of higher quantities of gases and much higher pressures inside the PC, which can lead to early rupture of the PC filter and higher radioactive aerosol release fractions. Therefore, a new series of tests was required to determine the temperature response of the exposed PC and determine the amount of material that could be released. DOE contacted SNL in 2015 to discuss the 1997 SNL tests and came to the conclusion that those tests were not bounding for POC/PC containing combustibles Therefore, DOE commission a new set of tests at SNL. Starting in 2015, SNL conducted fire tests to examine whether the contents of the PC would reach a temperature that would result in generation of sufficient gas to cause overpressurization of the PC, and subsequent release of its content. This paper will describe the various test conducted thus far, and present preliminary results from these tests.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Analysis of the likelihood of post-closure criticality in a geological disposal facility - 14349

Radioactive Waste Management (RWM) is responsible for implementing geological disposal of the UK's higher activity radioactive wastes. These wastes include significant quantities of fissile nuclides and, therefore, demonstration of the criticality safety of the wastes under disposal conditions forms an important component of RWM's disposal system safety case. At the time of disposal, controls will ensure that all waste packages are sub-critical, and the containment provided by the engineered barrier system of a geological disposal facility (GDF) will ensure that criticality is prevented for some time after disposal. However, as waste packages begin to degrade, fissile and other materials may be mobilised, which could affect the potential for criticality. Therefore, the possibility for the evolution of conditions in a GDF to result in criticality requires assessment. RWM established the 'Likelihood of Criticality' research project to develop qualitative and quantitative arguments to demonstrate that criticality after closure of a GDF is unlikely. The project included consideration of the criticality safety of disposal concepts for intermediate and high level waste, spent fuel, separated plutonium and highly-enriched uranium in different generic geological settings. The results are underpinned by the construction of post-closure criticality scenarios that have been evaluated using high-level judgments about scenario credibility as well as modelling of evolving conditions in a GDF. In the latter case, a probabilistic modelling approach has been undertaken to address uncertainty in the calculation of concentrations and masses of fissile material that could occur at potential accumulation sites. The potential for criticality has been judged based on comparisons of the calculated fissile masses with minimum values required for criticality at different locations in the barrier system. This paper explains the novel approach taken to evaluating the likelihood of criticality in a GDF based on the probabilistic modelling of waste package evolution and plutonium and uranium migration. The role of this research in RWM's work to demonstrate the criticality safety of a GDF in the UK is presented in a companion paper, which also draws on the results of a parallel research project that demonstrates that, even if a criticality were to occur, then its consequences would be insignificant to GDF performance. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Investigation of the continuous-energy sensitivity methods in scale 6.2 using Tsunami-3D - 14579

The SCALE 6.1 code system includes a multigroup (MG) method for three-dimensional (3D) sensitivity analyses via the Tools for Sensitivity and Uncertainty Analysis Methodology Implementation (TSUNAMI), and the upcoming release of SCALE 6.2 will feature the system's first implementation of continuous-energy (CE) sensitivity methods. Detailed information regarding the CE TSUNAMI-3D eigenvalue sensitivity methods is provided in a companion paper. This work compares the results of TSUNAMI-3D calculations using the traditional MG approach to the new CE CLUTCH method in SCALE 6.2. The systems examined in this study include combinations of fast, thermal, and mixed spectra with metal, compound, and solution material forms. The primary fissile species include low-enriched uranium, intermediate-enriched uranium, high-enriched uranium, plutonium, and mixed uranium and plutonium. This broad range of systems expands the experience base with the CE CLUTCH method, identifies best practices for using the code, and provides generic user guidance for utilizing this new capability. Additionally, the study demonstrates the accuracy and usefulness of the CE CLUTCH method, especially for systems for which MG methods perform poorly. (authors)

42 ENGINEERING↗

Sensitivity studies to Support TEX critical experiments design

In the frame of the ongoing Thermal/Epithermal experiments program, supported by the DOE-NCSP, we are characterizing expected data with analysis of sensitivity coefficients to nuclear data. The computations were performed for detailed and simplified models of the experimental configurations in order to demonstrate their invariance with respect to small geometry variations. The sensitivity coefficients were computed with recently developed precise methodologies using Monte Carlo tools (MCNP-6.1, SCALE 6.1 and MORET 5.C.1) with the following nuclear data libraries: ENDF/B-VII.0, ENDF/B-VII.1, and JEFF3.1. Since the considered experiments are devoted to tantalum data validation, their neutronic characteristics are compared with the relevant integral experiment data collected in the OECD/NEA ICSBEP Handbook. Although analysis of sensitivity coefficients taken alone is insufficient for an entire assessment, we can conclude that TEX experimental results can fill gaps in the available benchmarks to facilitate quantification of uncertainty for plutonium containing systems with epithermal neutron spectra (e.g. wet plutonium-based powders). However, analysis of sensitivity profiles demonstrates that an advanced statistical methodology will be needed to fit tantalum nuclear data or to evaluate the associated uncertainties. (authors)

42 ENGINEERING↗

Purification Techniques for Actinide Radiolysis Studies

Our fundamental understanding of actinide radiation-induced redox chemistry is crucial due to their unavoidable exposure to ionizing radiation fields, both inherent and from in-process applications. Plutonium (Pu) and americium (Am) both possess multiple oxidation states, the careful manipulation of which are essential in the study and utilization of their rich chemistry, developing new technologies, and securing the long-term sustainability of nuclear power. However, knowledge in this area is far from complete. We have studied the radiation-induced chemistry of both Pu and Am through a variety of techniques, including gamma irradiation, in-situ alpha irradiation and pulse radiolysis experiments. However, for the collection of accurate data, thorough purification and quantification of actinide-containing solutions is required. This presentation will cover the purification and quantification techniques employed for the radiolysis experiments described in our recent publications: Kynman et al., Multiscale Modeling of Plutonium Radiation Chemistry in Nitric Acid Solutions. 1. Cobalt-60 Gamma Irradiation of Pu(IV) [https://pubs.acs.org/doi/10.1021/acs.inorgchem.4c00138] and Kynman et al., Generation and Study of Am(IV) by Temperature-Controlled Electron Pulse Radiolysis [https://doi.org/10.1039/D4DT00991F].

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

AFC-1 Fuel Rodlet Fission Power Deposition Validation in ATR

One of the viable options of long-term geological disposal of the nuclear power reactors generated spent fuel is to extract plutonium, the minor actinides (MA) and potentially long-lived fission products from the spent fuel and transmute them into short-lived or stable radionuclides in an appropriate reactor for the reduction of the radiological toxicity of the nuclear waste stream. An important component of that technology will be a non-fertile / low-fertile actinide transmutation fuel form containing the plutonium, neptunium, americium (and possibly curium) isotopes to be transmuted. Such advanced fuel forms, especially ones enriched in the long-life minor actinide (LLMA) elements (i.e., Np, Am, Cm), have minimal irradiation performance data available from which to establish a transmutation fuel form design. Recognizing these needs, an Advanced Fuel Cycle test series-1 (AFC-1) irradiation test on a variety of candidate fuel forms is now being conducted in Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). The first advanced fuel experiment (AFC-1) has been finalized and the test assembly analyzed for insertion and irradiation in ATR. The ATR core consists of a serpentine and rotationally symmetric fuel assembly about the z-axis of the core center. The plan view of the ATR core configuration is shown in Fig. 5, in Ref. 1. A cadmium filter with a 0.178 cm (0.045") thickness and 121.5 cm (48") in length, is currently used in the actinide-fuel capsule design for the East Flux Trap (EFT) position in ATR, to depress the linear heat generation rate (LHGR) lower than the project’s 330 W/cm limit for the experimental fuel rodlets. The LHGR is proportional to the fission power deposited in the fuel rodlets from the neutron fissions. The fraction of the fission power generated from the neutron fission reactions deposited in the fuel rodlet is an important parameter for test assembly thermal analysis, which will be validated in this summary.

99 GENERAL AND MISCELLANEOUS↗

STRESS CORROSION CRACKING IN TEAR DROP SPECIMENS

Laboratory tests were conducted to investigate the stress corrosion cracking (SCC) of 304L stainless steel used to construct the containment vessels for the storage of plutonium-bearing materials. The tear drop corrosion specimens each with an autogenous weld in the center were placed in contact with moist plutonium oxide and chloride salt mixtures. Cracking was found in two of the specimens in the heat affected zone (HAZ) at the apex area. Finite element analysis was performed to simulate the specimen fabrication for determining the internal stress which caused SCC to occur. It was found that the tensile stress at the crack initiation site was about 30% lower than the highest stress which had been shifted to the shoulders of the specimen due to the specimen fabrication process. This finding appears to indicate that the SCC initiation took place in favor of the possibly weaker weld/base metal interface at a sufficiently high level of background stress. The base material, even subject to a higher tensile stress, was not cracked. The relieving of tensile stress due to SCC initiation and growth in the HAZ and the weld might have foreclosed the potential for cracking at the specimen shoulders where higher stress was found.

36 MATERIALS SCIENCE↗

Final evaluation of characterizing pipe-over-pack containers using high efficiency neutron counters

Nondestructive assay (NDA) measurements of Transuranic (TRU) waste at Los Alamos National Laboratory (LANL) packed in Pipe-over-Pack Containers (POC) contain a number of complexities. The POC is highly attenuating to both gamma rays and neutrons which presents a difficult waste matrix for correct quantification of material in the container. Currently there are a number ofPOC containers at LANL that require evaluation for shipment to the Waste Isolation Pilot Plant (WIPP) in Carlsbad, NM. Updated data has been evaluated that finalizes the evaluation of characterizing Pipe-Over-Pack Containers. Currently at LANL, a single instrument has been used to explore the appropriateness of both passive neutron and quantitative gamma ray methods for measuring POC's. The passive neutron approach uses the Reals coincidence count rate to establish plutonium mass and other parameters of interest for TRU waste. The quantitative gamma ray method assumes a homogeneous distribution of radioactive source material with the surrounding material throughout the drum volume. Drums are assayed with a calibration based on the known density of the matrix. Both methods are supplemented by a simultaneous isotopic measurement using Multi-Group Analysis (MGA) to determine the plutonium isotopic composition. If MGA fails to provide a viable isotopic result Fixed Energy Response function Analysis with Multiple efficiencies (FRAM) has been used to replace the MGA results. Acceptable Knowledge (AK) may also be used in certain instances. This report will discuss the two methods in detail. Included in the discussion will be descriptions of the setup parameters and calibration techniques for the instrument. A number of test measurements have been performed to compare HENC data with certified historical data. Empty POCs loaded with known sources have also been measured to determine the viability of the technique. A comparison between calorimetry data, historical measurements and HENC data will also be performed. The conclusion will show that the current calibration on the HENC units is viable for analysis of POCs.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Dexterity test data contribute to reduction in leaded glovebox gloves use

Programmatic operations at the Los Alamos National Laboratory Plutonium Facility (T A-55) involve working with various amounts of plutonium and other highly toxic, alpha-emitting materials. The spread of radiological contamination on surfaces, airborne contamination, and excursions of contaminants into the operator's breathing zone are prevented through the use of a variety of gloveboxes. Using an integrated approach, controls have been developed and implemented through an efficient Glovebox Glove Integrity Program. A key element of this program is to consider measures that lower the overall risk of glovebox operations. Line management who own glovebox processes through this program make decisions on which type of glovebox gloves (hereafter referred to as gloves), the weakest component of this safety-significant system, would perform best in these aggressive environments. As Low as Reasonably Achievable considerations must be balanced with glove durability and worker dexterity, both of which affect the final overall risk of the operation. In the past, lead-loaded (leaded) gloves made from Hypalon(reg.) were the primary glove for programmatic operations at TA55. Replacing leaded gloves with unleaded gloves for certain operations would lower the overall risk as well as reduce the amount of mixed transuranic waste. This effort contributes to the Los Alamos National Laboratory Continuous Improvement Program by improving the efficiency, cost-effectiveness, and formality of glovebox operations. In this report, the pros and cons of wearing leaded gloves, the effect of leaded gloves versus unleaded gloves on task performance using standard dexterity tests, the justification for switching from leaded to unleaded gloves, and the pollution prevention benefits of this dramatic change in the glovebox system are presented.

42 ENGINEERING↗

A Re-Introduction to "Anomalies of Criticality"

In 1974, a small innocuous document was submitted to the American Nuclear Society's Criticality Safety Division for publication that would have lasting impacts on this nuclear field The author was Duane Clayton, manager of the Battelle Pacific Northwest National Laboratory's Critical Mass Lab, the world's preeminent reactor critical experimenter with plutonium solutions. The document was entitled, 'Anomalies of Criticality'. 'Anomalies...' was a compilation of more than thirty separate and distinct examples of departures from what might be commonly expected in the field of nuclear criticality. Mr. Clayton's publication was the derivative of more than ten thousand experiments and countless analytical studies conducted world-wide on every conceivable reactor system imaginable: from fissile bearing solutions to solids, blocks to arrays of fuel rods, low-enriched uranium oxide systems to pure plutonium and highly enriched uranium systems. After publication, the document was commonly used within the nuclear fuel cycle and reactor community to train potential criticality/reactor analysts, experimenters and fuel handlers on important things for consideration when designing systems with critically 'safe' parameters in mind The purpose of this paper is to re-introduce 'Anomalies of Criticality' to the current Criticality Safety community and to add new 'anomalies' to the existing compendium. By so doing, it is the authors' hope that a new generation of nuclear workers and criticality engineers will benefit from its content and might continue to build upon this work in support of the nuclear renaissance that is about to occur.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

THERMAL ANALYSIS OF 3013/9975 CONFIGURATION

The 3013 containers are designed in accordance with the DOE-STD-3013-2004 and are qualified to store plutonium (Pu) bearing materials for 50 years. The U.S. Department of Energy (DOE) certified Model 9975 shipping package is used to transport the 3013 containers to the K-Area Material Storage (KAMS) facility at the Savannah River Site (SRS) and to store the containers until the plutonium can be properly dispositioned. Detailed thermal analyses to support the storage in the KAMS facility are given in References 2, 3, and 4. The analyses in this paper serve to provide non-accident condition, non-bounding, specific 3013 container temperatures for use in the surveillance activities. This paper presents a methodology where critical component temperatures are estimated using numerical methods over a range of package and storage parameters. The analyses include factors such as ambient storage temperature and the content weight, density, heat generation rate, and fill height, that may impact the thermal response of the packages. Statistical methods are used to develop algebraic equations for ease of computations to cover the factor space. All computations were performed in BTU-FT-Hr-{sup o}F units.

42 ENGINEERING↗

Minor Actinides Loading Optimization for Proliferation Resistant Fuel Design - BWR

One approach to address the United States Nuclear Power (NP) 2010 program for the advanced light water reactor (LWR) (Gen-III+) intermediate-term spent fuel disposal need is to reduce spent fuel storage volume while enhancing proliferation resistance. One proposed solution includes increasing burnup of the discharged spent fuel and mixing minor actinide (MA) transuranic nuclides ( 237 Np and 241 Am) in the high burnup fuel. Thus, we can reduce the spent fuel volume while increasing the proliferation resistance by increasing the isotopic ratio of 238 Pu/Pu. For future advanced nuclear systems, MAs are viewed more as a resource to be recycled and transmuted to less hazardous and possibly more useful forms, rather than simply disposed of as a waste stream in an expensive repository facility. MAs play a much larger part in the design of advanced systems and fuel cycles, not only as additional sources of useful energy, but also as direct contributors to the reactivity control of the systems into which they are incorporated. A typical boiling water reactor (BWR) fuel unit lattice cell model with UO 2 fuel pins will be used to investigate the effectiveness of adding MAs ( 237 Np and/or 241 Am) to enhance proliferation resistance and improve fuel cycle performance for the intermediate-term goal of future nuclear energy systems. However, adding MAs will increase plutonium production in the discharged spent fuel. In this work, the Monte-Carlo coupling with ORIGEN-2.2 (MCWO) method was used to optimize the MA loading in the UO 2 fuel such that the discharged spent fuel demonstrates enhanced proliferation resistance, while minimizing plutonium production. The axial averaged MA transmutation characteristics at different burnup were compared and their impact on neutronics criticality and the ratio of 238 Pu/Pu discussed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

RESIDUAL STRESSES IN 3013 CONTAINERS

The DOE Complex is packaging plutonium-bearing materials for storage and eventual disposition or disposal. The materials are handled according to the DOE-STD-3013 which outlines general requirements for stabilization, packaging and long-term storage. The storage vessels for the plutonium-bearing materials are termed 3013 containers. Stress corrosion cracking has been identified as a potential container degradation mode and this work determined that the residual stresses in the containers are sufficient to support such cracking. Sections of the 3013 outer, inner, and convenience containers, in both the as-fabricated condition and the closure welded condition, were evaluated per ASTM standard G-36. The standard requires exposure to a boiling magnesium chloride solution, which is an aggressive testing solution. Tests in a less aggressive 40% calcium chloride solution were also conducted. These tests were used to reveal the relative stress corrosion cracking susceptibility of the as fabricated 3013 containers. Significant cracking was observed in all containers in areas near welds and transitions in the container diameter. Stress corrosion cracks developed in both the lid and the body of gas tungsten arc welded and laser closure welded containers. The development of stress corrosion cracks in the as-fabricated and in the closure welded container samples demonstrates that the residual stresses in the 3013 containers are sufficient to support stress corrosion cracking if the environmental conditions inside the containers do not preclude the cracking process.

42 ENGINEERING↗

Experimental Observations and Numerical Prediction of Induction Heating in a Graphite Test Article

The induction heating coils used in the plutonium casting furnaces at the Los Alamos National Laboratory are studied here. A cylindrical graphite test article has been built, instrumented with thermocouples, and heated in the induction coil that is normally used to preheat the molds during casting operations. Preliminary results of experiments aimed at understanding the induction heating process in the mold portion of the furnaces are reported. The experiments have been modeled in COMSOL Multiphysics and the numerical and experimental results are compared to one another. These comparisons provide insight into the heating process and provide a benchmark for COMSOL calculations of induction heating in the mold portion of the plutonium casting furnaces.

42 ENGINEERING↗

Electrochemically-Modulated Separation and Mass Spectrometric Analysis of Actinides in Difficult Matrices

Electrochemically-modulated separations (EMS) are a straightforward means of isolating and pre-concentrating elements for on-line mass spectrometric analysis. Elements are accumulated at electrochemical working electrodes and subsequently released into a clean carrier solution for spectroscopic analysis. EMS can employ solely aqueous chemistry and uses electrochemical redox adjustment of oxidation state to “trigger” reversible chelation / complexation. Less tractable elements (e.g., uranium and plutonium), based on redox potentials, can therefore be extracted from difficult matrices following redox adjustment and chelation with electrode chelation sites. Simply put, separation is achieved by a small voltage step that is applied to the target electrode to turn “on” or “off” the specific actinide affinity of an electrode. This separation technology employs both redox and chelation chemistry to effect highly selective accumulation of target actinides, and results in element separation, matrix elimination and analyte preconcentration. Prior studies have developed protocols and preliminary insight into EMS processes for U and Pu. U and Pu are released upon oxidation and reduction, respectively, allowing complete separation due to widely divergent redox potentials. T The coupling of EMS on-line with ICP-MS for elemental and isotopic analysis of uranium and plutonium is presented, with a focus on analytical performance metrics and applicability to safeguards and process monitoring via nondestructive analyses.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Dexterity test data contribute to proper glovebox over-glove use

Programmatic operations at the Los Alamos National Laboratory Plutonium Facility (TA-55) involve working with various amounts of plutonium and other highly toxic, alpha-emitting materials. The spread of radiological contamination on surfaces, airborne contamination, and excursions of contaminants into the operator's breathing zone are prevented through the use of a variety of gloveboxes (the glovebox, coupled with an adequate negative pressure gradient, provides primary confinement). The glovebox gloves are the weakest part of this engineering control. The Glovebox Glove Integrity Program, which controls glovebox gloves from procurement to disposal at TA-55, manages this vulnerability. A key element of this program is to consider measures that lower the overall risk of glovebox operations. Proper selection of over-gloves is one of these measures. Line management owning glovebox processes have the responsibility to approve the appropriate personal protective equipment/glovebox glove/over-glove combination. As low as reasonably achievable (ALARA) considerations to prevent unplanned glovebox glove openings must be balanced with glove durability and worker dexterity, both of which affect the final overall risk to the worker. In this study, the causes of unplanned glovebox glove openings, the benefits of over-glove features, the effect of over-gloves on task performance using standard dexterity tests, the pollution prevention benefits, and the recommended over-gloves for a task are presented.

57↗