Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSURE EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Influence of gradation on shear behavior and pore water response of sand

Here, this paper examines the influence of particle size distribution (PSD) on the shearing behavior of sand using axisymmetric triaxial compression (ATC) testing in conjunction with 3D imaging using synchrotron micro-computed tomography (SMT). Angular sand was sieved to obtain a narrow gradation (uniform) and a wide gradation (non-uniform) with uniformity coefficients (C u ) of 1.2 and 3.0, respectively. Experiments were conducted under drained conditions and a constant effective cell pressure (σ$^{'}_3$) of 50 kPa at low and high back pressures (BP). Results of paired ATC-SMT were analyzed in terms of global constitutive behavior, strain localization, and localized flow characteristics. A new particle tracking algorithm is developed to expose strain localization. Relative particle translation gradient (RPTG) results revealed that gradation affects how early the shear band develops and a tendency for narrow gradation to exhibit varying degrees of diffused shear band at high axial strain (ε 1 ) even though a clear single shear band was observed at the peak strength. Geometric tortuosity (τ) is used as a quantitative parameter to assess flow changes and the efficiency of the flow path. Representative elementary volumes (REVs) inside and outside the shear band were analyzed and the results showed a variation in flow path characteristics where wide gradation specimens had preferential flow paths.

Computed tomography↗
DOE OSTI2024

Migration and accumulation of hydrous mantle incipient melt in the Earth's asthenosphere: Constraints from in-situ falling sphere viscometry measurements

The Earth's oceanic lithosphere-asthenosphere boundary (LAB) is marked by a notable decrease in seismic wave velocities and an increase in attenuation. This phenomenon is likely attributed to the accumulation of partial melt at the top of the asthenosphere. Nevertheless, the process involving the upward migration and aggregation of low-degree partial melts, highly likely to be mantle incipient melts in the asthenosphere, remains underexplored. Viscosity is a key factor controlling the flow of melts, thus in this study, we used In-situ X-ray falling sphere viscometry experiments to determine the viscosity of the mantle incipient melt containing 1.8–4.0 wt.% water at 1.5–6 GPa and 2100 K. We found that water and pressure can effectively decrease the viscosity of the mantle incipient melt. Therefore, the mantle incipient melts are highly mobile with a high segregation velocity in the deeper part of the asthenosphere. However, during ascent, their mobility diminishes due to an increase in viscosity and a decrease in water content. In conclusion, these mechanisms potentially contribute to the accumulation of partial melt at the top of the asthenosphere.

58 GEOSCIENCES↗
DOE OSTI2024

A chemical kinetic analysis of knock propensity of methanol-to-gasoline fuel

Production of low carbon gasoline-like fuels such as methanol-to-gasoline (MTG) is a promising approach to achieve rapid greenhouse gas emission reduction of the transportation sector. Despite the fact that gasoline that meets the ASTM D4814 standard for automotive spark-ignition engine fuel can be readily produced from these processes, it is unclear how the composition of MTG may affect engine performance and emissions. Here, in this paper, a surrogate for an MTG is used to numerically study the effects of gasoline composition on knock propensity and on the sensitivity of knock to thermal and fuel stratification, to oxygen dilution and to nitric oxide from exhaust gas recirculation of residual gases. Simulations were performed in ANSYS CHEMKIN-PRO using a comprehensive chemical kinetic mechanism for gasoline surrogates, and results of the MTG surrogate were compared against those of a petroleum-based regular E10 gasoline, termed PACE-20. A premium-grade MTG fuel was also formulated by adding ethanol to the MTG surrogate, and results were compared against those of four premium-grade, gasoline-like fuels representative of future alternative gasoline formulations. Surrogates and mechanism were evaluated by comparison against experimental engine data, and the model showed high accuracy at stoichiometric conditions (mean absolute error of ignition timing equal to 1.46 crank angle degrees) but larger deviations at lean conditions (mean absolute error of ignition timing equal to 5.52 crank angle degrees). Despite the fact that the MTG surrogate has a RON 1.1 units higher than that of PACE-20, it may show higher knock propensity at medium temperature conditions due to a less intense NTC behavior. MTG autoignition was more temperature- and equivalence ratio-sensitive than that of PACE20, suggesting that MTG can benefit more from naturally-occurring thermal stratification or from induced fuel stratification of the end gas to mitigate knock intensity. The sensitivity of autoignition reactivity to oxygen dilution and to NO concentration was higher for MTG than for regular gasoline at medium loads, but the opposite trend was observed at high loads due to the effect of pressure on the low-temperature chemistry of regular gasoline. Approximately 14 % vol ethanol content was required to upgrade the octane rating of MTG from regular grade to premium grade. Adding 13.6 % vol ethanol made the fuel autoignition less sensitive to both oxygen dilution and NO content (ignition time varies approx. 17 % and 50 % less with oxygen dilution and NO addition, respectively, when adding ethanol at high engine loads).

02 PETROLEUM↗
DOE OSTI2019

Opacity of shock-heated boron plasmas

Standard measures of opacity, the imaginary part of the atomic scattering factor f 2 and the x-ray mass attenuation coefficient μ/ρ, are assessed in shock-heated boron, boron carbide and boron nitride plasmas. The Hugoniot equation, relating the temperature T behind a shock wave to the compression ratio ρ/ρ 0 across the shock front, is used in connection with the plasma equation of state to determine the pressure p, effective plasma charge Z* and the K-shell occupation in terms of ρ/ρ 0 . Solutions of the Hugoniot equation (determined within the framework of the generalized Thomas–Fermi theory) show that the K-shell occupation in low-Z ions decreases rapidly from 2 to 0.1 as the temperature increases from 20 eV to 500 eV; a temperature range in which the shock compression ratio is near 4. The average-atom model (a quantum mechanical version of the generalized Thomas–Fermi theory) is used to determine K-shell and continuum wave functions and the photoionization cross section for x-rays in the energy range ω = 1 eV to 10 keV, where the opacity is dominated by the atomic photoionization process. For an uncompressed boron plasma at T = 10 eV, where the K-shell is filled, the average-atom cross section, the atomic scattering factor and the mass attenuation coefficient are all shown to agree closely with previous (cold matter) tabulations [1, 2, 3]. For shock-compressed plasmas, the dependence of μ/ρ on temperature can be approximated by scaling previously tabulated cold-matter values by the relative K-shell occupation; yet, there is a relatively small residual dependence arising from the photoionization cross section. Attenuation coefficients μ for a 9 keV x-ray are given as functions of T along the Hugoniot for B, C, B 4 C and BN plasmas.

52.25.Os: Emission↗
DOE OSTI2023

Fundamental study of gas species transport in the oxygen electrode of solid oxide fuel and electrolysis cells

A fundamental analysis of multicomponent gas transport models was performed in application to the oxygen electrodes of solid oxide cells. It is common practice to neglect the effect of pressure gradients within oxygen electrodes, even though a net molar flux at the electrolyte surface implies that a pressure gradient must exist. The influence of both Darcy velocity and Knudsen flux are considered in the context of ordinary (Fickian) diffusion, the dusty gas model, and the binary friction model. Comparisons between the models and different sets of assumptions are made via parametric studies on operating load, oxygen partial pressure, microstructural properties, and electrode thickness. Results show that the pressure gradient will have a significant impact on the oxygen concentration distribution and therefore the concentration overpotential. In electrolysis mode, pressure increases up to 1 atm are predicted, indicating that pressure at the electrode/electrolyte interface could contribute to electrode delamination. Additionally, it is found that Darcy's law is insufficient for calculating the pressure distribution without accounting for the flux due to Knudsen diffusion. Additionally, it is found that for the range of properties typical of oxygen electrodes, there is a negligibly small difference between the dusty gas model and binary friction model from a practical standpoint.

08 HYDROGEN↗
DOE OSTI2021

An experimentally validated evaporative phase change heat transfer model for low mass flux applications using R134a in plate heat exchangers

Plate frame heat exchangers are common in liquid-coupled vapor compression systems due to their compactness and ease of maintenance. In some of these systems, the refrigerant within the evaporator can enter the heat exchanger as a subcooled liquid. As a result, the refrigerant passes through three different phases: single-phase liquid, two-phase fluid, and a superheated vapor. Unfortunately, there have been limited prior studies that have identified the best method to predict performance under these circumstances. Furthermore, previous investigations have not evaluated refrigerant evaporation in large industrial sized plate frame heat exchangers under conditions experienced in the present study experimental test facility, especially at mass fluxes below 7 kg m –2 s –1 . In the present investigation, a model was developed to predict the performance of plate and frame heat exchangers when the fluid enters as a subcooled liquid and exits as a superheated vapor. The model used full-sized plate heat exchanger geometry that was discretized into 20 sections to accurately capture local heat transfer and pressure drop effects. The model was validated using an R134a counter flow heat exchanger used in a turbo-compression cooling system test facility that had subcooled liquid entering the evaporator at low mass fluxes. A variety of empirical correlations were evaluated to determine what combination yielded the best predictive capability over the following range of conditions: 5.8 < G < 6.8 kg m –2 s –1 , 2 < q” < 2.8 kW m –2 , and 10 °C < T sat < 15 °C. When the correlations used a fixed control volume length in the heat flux calculation, the most accurate combination resulted in a mean absolute error of 5.5%. Finally, future studies can use the approach described here to optimize heat exchanger size and performance.

42 ENGINEERING↗
DOE OSTI2016

Analytical approach for describing the collapse of surface asperities under compressive stress during rapid solid state bonding

Many material manufacturing technologies, such as friction stir welding, rely on rapid solid state bonding to join metal surfaces. In this letter, a differential equation is developed to formulate the growing of the interfacial bonded area owing to the collapse of surface asperities under compressive stress during rapid solid state bonding of metal surfaces. The effect of pressure, temperature and bonding time on the growing of bonded area is discussed. The proposed approach is verified by experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Improving Cycling Performance of Anode-Free Lithium Batteries by Pressure and Voltage Control

The anode-free lithium (Li) batteries (AFLBs) have great potential to provide higher energy density than most other batteries. However, the performance of AFLBs is very sensitive to pressure and other operating parameters, especially for coin cells widely used in AFLB investigations. Therefore, optimizing cell assembly parameters and test protocol is critical to get reliable and comparable results in this field. In this work, the operating voltage range of AFLBs using a localized high concentration electrolyte has been optimized. The morphology of the deposited Li in AFLBs is much more indicting to the pressure than other type of batteries due to the absence of anode active material (i.e. Li) as a pressure cushion layer in the as prepared cells. With an optimized cycling protocol, a thin layer of uniform nucleation sites can be formed in the initial cycle which will facilitate smooth Li desposition/stripping in the subsequent cycles of AFLBs. The solid electrolyte interphase layer formed under optimized pressure and uniform pressure distribution exhibits a good mechanical stability even after long-term cycling. In conclusion, with an optimized cell configuration, the internal pressure in the coin cells has been optimized to improve the cycling performance of AFLBs (Cu||NMC811) with 72% of capacity retention in 100 cycles.

25 ENERGY STORAGE↗
DOE OSTI2018

Abnormal Elasticity of Fe-Bearing Bridgmanite in the Earth's Lower Mantle

We measured the effect of pressure on the compressional and shear wave velocity (V P , V S ) as well as density of Fe-bearing bridgmanite, Mg 0.96(1) Fe 2+ 0.036(5) Fe 3+ 0.014(5) Si 0.99(1) O 3 , using impulsive stimulated light scattering, Brillouin light scattering, and X-ray diffraction, respectively, in diamond anvil cells up to 70 GPa at 300 K. A drastic softening of V P by ~6(±1)% is observed between 42.6 and 58 GPa, while V S increases continuously with increasing pressure. A significant reduction in Poisson's ratio from 0.24 to 0.16 occurs at ~42.6–58 GPa, while VS increases by ~3(±1)% above ~40 GPa compared to MgSiO 3- bridgmanite. Thermoelastic modeling of the experimental results shows that the observed elastic anomaly of Fe-bearing bridgmanite is consistent with a spin transition of octahedrally coordinated Fe 3+ in bridgmanite. These results challenge traditional views that Fe enrichment will reduce seismic velocities, suggesting that seismic heterogeneities in the mid-lower mantle may be due to a spin transition of Fe in Fe-bearing bridgmanite.

58 GEOSCIENCES↗
DOE OSTI2022

Dissolving salt is not equivalent to applying a pressure on water

Abstract Salt water is ubiquitous, playing crucial roles in geological and physiological processes. Despite centuries of investigations, whether or not water’s structure is drastically changed by dissolved ions is still debated. Based on density functional theory, we employ machine learning based molecular dynamics to model sodium chloride, potassium chloride, and sodium bromide solutions at different concentrations. The resulting reciprocal-space structure factors agree quantitatively with neutron diffraction data. Here we provide clear evidence that the ions in salt water do not distort the structure of water in the same way as neat water responds to elevated pressure. Rather, the computed structural changes are restricted to the ionic first solvation shells intruding into the hydrogen bond network, beyond which the oxygen radial-distribution function does not undergo major change relative to neat water. Our findings suggest that the widely cited pressure-like effect on the solvent in Hofmeister series ionic solutions should be carefully revisited.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Pressure-induced charge orders and their postulated coupling to magnetism in hexagonal multiferroic LuFe 2 O 4

Hexagonal LuFe 2 O 4 is a promising charge order (CO) driven multiferroic material with high charge and spin-ordering temperatures. The coexisting charge and spin orders on Fe 3+ /Fe 2+ sites result in magnetoelectric behaviors, but the coupling mechanism between the charge and spin orders remains elusive. Here, by tuning external pressure, we reveal three charge-ordered phases with suggested correlation to magnetic orders in LuFe 2 O 4 : (i) a centrosymmetric incommensurate three-dimensional CO with ferrimagnetism, (ii) a non-centrosymmetric incommensurate quasi-two-dimensional CO with ferrimagnetism, and (iii) a centrosymmetric commensurate CO with antiferromagnetism. Experimental in situ single-crystal X-ray diffraction and X-ray magnetic circular dichroism measurements combined with density functional theory calculations suggest that the charge density redistribution caused by pressure-induced compression in the frustrated double-layer [Fe 2 O 4 ] cluster is responsible for the correlated spin-charge phase transitions. The pressure-enhanced effective Coulomb interactions among Fe-Fe bonds drive the frustrated (1/3, 1/3) CO to a less frustrated (1/4, 1/4) CO, which induces the ferrimagnetic to antiferromagnetic transition. Our results not only elucidate the coupling mechanism among charge, spin, and lattice degrees of freedom in LuFe 2 O 4 , but also provide a new way to tune the spin-charge orders in a highly controlled manner.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Substantial influence of vapour buoyancy on tropospheric air temperature and subtropical cloud

The molar mass of water vapor is less than that of dry air, making humid air lighter than dry air at the same temperature and pressure. This effect is known as vapor buoyancy and has been considered negligibly small in large-scale climate dynamics. Here we use theory, reanalysis data, and a hierarchy of climate models to show that vapor buoyancy has a similar magnitude to thermal buoyancy in the tropical free troposphere. We further show that vapor buoyancy makes cold air rise and increases subtropical stratiform low clouds by up to 70% of its climatological value. However, some widely used climate models fail to represent vapor buoyancy in the governing equations. Further, this flaw leads to inaccurate simulations of cloud distributions—the largest uncertainty in predicting climate change.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Two-dimensional diamonds from sp 2 -to- sp 3 phase transitions

The ability to change material properties through phase engineering has long been sought, with the goal of ad hoc tunability of the physical and chemical properties of the transformed phases. The synthesis and study of graphene have made it possible to explore the mechanisms of 2D phase transformations, opening up paths towards the formation of 2D diamond and diamond thin films. This Review examines the state-of-the-art phase transformations in 2D graphitic systems and beyond. The theoretical models formulated to describe the sp2-to-sp3 transitions from graphene to 2D diamond and the experimental processes developed to induce the transition to 2D diamond are discussed, focusing on the transformations induced by chemical functionalization and pressure. The effects of different structural and environmental factors on the evolution of the phase transformations and on the properties of the transformed diamond phases are explored. Without comprehensively reviewing phase transitions in all 2D materials, we briefly mention hexagonal boron nitride, phosphorene, transition metal dichalcogenides and MXenes systems. Lastly, the Review delves into the technologies and applications of phase transformations in 2D materials and the opportunities for this field.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Flash (Ultra-Rapid) Spark-Plasma Sintering of Silicon Carbide

A new ultra-rapid process of flash spark plasma sintering is developed. The idea of flash spark plasma sintering (or flash hot pressing - FHP) stems from the conducted theoretical analysis of the role of thermal runaway phenomena for material processing by flash sintering. The major purpose of the present study is to theoretically analyze the thermal runaway nature of flash sintering and to experimentally address the challenge of uncontrollable thermal conditions by the stabilization of the flash sintering process through the application of the external pressure. The effectiveness of the developed FHP technique is demonstrated by the few seconds–long consolidation of SiC powder in an industrial spark plasma sintering device. Specially designed sacrificial dies heat the pre-compacted SiC powder specimens to a critical temperature before applying any voltage to the powder volume and allowing the electrode-punches of the SPS device setup to contact the specimens and pass electric current through them under elevated temperatures. The experimental results demonstrate that flash sintering phenomena can be realized using conventional SPS devices. The usage of hybrid heating SPS devices is pointed out as the mainstream direction for the future studies and utilization of the new flash hot pressing (ultra-rapid spark plasma sintering) technique.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Error field penetration and locking to the backward propagating wave

In this letter we investigate error field penetration, or locking, behavior in plasmas having stable tearing modes with finite real frequencies w r in the plasma frame. In particular, we address the fact that locking can drive a significant equilibrium flow. We show that this occurs at a velocity slightly above v = w r /k, corresponding to the interaction with a backward propagating tearing mode in the plasma frame. Results are discussed for a few typical tearing mode regimes, including a new derivation showing that the existence of real frequencies occurs for viscoresistive tearing modes, in an analysis including the effects of pressure gradient, curvature and parallel dynamics. The general result of locking to a finite velocity flow is applicable to a wide range of tearing mode regimes, indeed any regime where real frequencies occur.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗