Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Mount”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

The Design of Pumpjets for Hydrodynamic Propulsion

A procedure for use in the design of a wake adapted pumpjet mounted on the aft end of a body of revolution is presented. To this end, a pumpjet is designed for the Akron airship. The propulsor mass flow is selected to minimize kinetic energy losses through the duct and in the discharge jet. The shaft speed and disk size are selected to satisfy specified limits of cavitation performance and to provide acceptable blade loading. The streamtubes which pass through a propulsor mounted on a tapered afterbody follow essentially conical surfaces. A method is provided for defining these surfaces as a function of shroud geometry, rotor head distribution, and the energy distribution of the ingested mass flow. The three-dimensional effects to which the conical flow subjects the cylindrical blade design sections are described and a technique is presented which permits incorporation of these effects in the blade design procedure.

Bruce, E. P.↗
NASA NTRS1974

Aerodynamic roll damping of a T-tail transport configuration

The aerodynamic roll damping and the yawing moment due to roll rate for a model of a T-tail transport with aft-mounted engines were measured by means of a small-amplitude forced-oscillation mechanism. The tests were made for Mach numbers between 0.21 and 0.80 over a range of angles of attack from about minus 4 deg to 22 deg. The basic configuration had positive damping in roll at low angles of attack with regions of low positive and negative damping for angles of attack above 8 deg to 10 deg. There was good agreement between the theoretical estimates of the roll damping for the wing alone and the experimental results at an angle of attack of 0 deg for Mach numbers of 0.60 and less. The T-tail configuration and the engine nacelles mounted aft on the fuselage did not significantly affect either the damping in roll or the yawing moment due to roll rate.

Boyden, R. P.↗
NASA NTRS1974

Apparatus for microbiological sampling

An automatic apparatus is described for microbiologically sampling surface using a cotton swab which eliminates human error. The apparatus includes a self-powered transport device, such as a motor-driven wheeled cart, which mounts a swabbing motor drive for a crank arm which supports a swab in the free end thereof. The swabbing motor is pivotably mounted and an actuator rod movable responsive to the cart traveling a predetermined distance provides lifting of the swab from the surface being sampled and reversal of the direction of travel of the cart.

Wilkins, J. R.↗
NASA NTRS1975

Low-speed wind-tunnel investigation of forward-located spoilers and trailing splines as trailing-vortex hazard-alleviation devices on an aspect-ratio-8 wing model

An investigation was made in the Langley V/STOL tunnel in order to determine, by the trailing-wing sensor technique, the effectiveness of either a forward-mounted spoiler or a tip-mounted spline as trailing-vortex attenuation devices on an unswept aspect-ratio-8 wing model. The trailing-wing rolling-moment data taken in the tunnel diffuser section show good agreement with the data taken in the tunnel test section. This agreement indicates that reasonable results may be obtained in the Langley V/STOL tunnel in experimental investigations of the trailing-vortex hazard at relatively great distances behind aircraft models.

Croom, D. R.↗
NASA NTRS1975

Normal injection of helium from swept struts into ducted supersonic flow

Recent design studies have shown that airframe-integrated scramjets should include instream mounted, swept-back strut fuel injectors to obtain short combustors. Because there was no data in the literature on mixing characteristics of swept strut fuel injectors, the present investigation was undertaken to provide such data. This investigation was made with two swept struts in a closed duct at Mach number of 4.4 and nominal jet-to-air mass flow ratio of 0.029 with helium used to simulate hydrogen fuel. The data is compared with flat plate mounted normal injector data to obtain the effect of swept struts on mixing. Three injector patterns were evaluated representing the range of hole spacing and jet-to-freestream dynamic pressure ratio of interest. Measured helium concentration, pitot pressure, and static pressure in the downstream mixing region are used to generate contour plots necessary to define the mixing region flow field and the mixing parameters.

Mcclinton, C. R.↗
NASA NTRS1975

Spacecraft detumbling using movable telescoping appendages

The dynamics of detumbling a randomly spinning spacecraft using externally mounted, movable telescoping appendages were studied both analytically and numerically. Two types of telescoping appendages are considered: where an end mass is mounted at the end of an (assumed) massless boom; and where the appendage is assumed to consist of a uniformly distributed homogeneous mass throughout its length. From an application of Liapunov's second method, boom extension maneuvers were determined to approach either of two desired final states: close to a zero inertial angular velocity state, and a final spin rate about only one of the principal axes. Recovery dynamics are evaluated analytically for the case of symmetrical deployment. Numerical examination of other asymmetrical cases verifies the practicality of using movable appendages to recover a randomly tumbling spacecraft.

Bainum, P. M.↗
NASA NTRS1975

Effect of vertical-tail location on the aerodynamic characteristics at subsonic speeds of a close-coupled canard configuration

The effects were studied of various vertical-tail configurations on the longitudinal and lateral directional-stability characteristics of a general research fighter model utilizing wing-body-canard. The study indicates that the addition of the high canard resulted in an increase in total lift at angles of attack above 4 deg with a maximum lift coefficient about twice as large as that for the wing-body configuration. For the wing-body (canard off) configuration, the center-line vertical tail indicates positive vertical-tail effectiveness throughout the test angle-of-attack range; however, for this configuration none of the wing-mounted vertical-tail locations tested resulted in a positive directional-stability increment at the higher angles of attack. For the wing-body-canard configuration several outboard locations of the wing-mounted vertical tails were found.

Huffman, J. K.↗
NASA NTRS1974

Wind tunnel test of model target thrust reversers for the Pratt and Whitney aircraft JT8D-100 series engines installed on a 727-200 airplane

The results of a low speed wind tunnel test of 0.046 scale model target thrust reversers installed on a 727-200 model airplane are presented. The full airplane model was mounted on a force balance, except for the nacelles and thrust reversers, which were independently mounted and isolated from it. The installation had the capability of simulating the inlet airflows and of supplying the correct proportions of primary and secondary air to the nozzles. The objectives of the test were to assess the compatibility of the thrust reversers target door design with the engine and airplane. The following measurements were made: hot gas ingestion at the nacelle inlets; model lift, drag, and pitching moment; hot gas impingement on the airplane structure; and qualitative assessment of the rudder effectiveness. The major parameters controlling hot gas ingestion were found to be thrust reverser orientation, engine power setting, and the lip height of the bottom thrust reverser doors on the side nacelles. The thrust reversers tended to increase the model lift, decrease the drag, and decrease the pitching moment.

Hambly, D.↗
NASA NTRS1975

Results of investigations on an 0.015-scale model (49-0) of the Rockwell International Space Shuttle orbiter in the NASA-Ames Research Center 3.5-foot hypersonic wind tunnel (0A98)

The results of a wind tunnel test are presented; the model used for this test was 0.015-scale 140 A/B hybrid configuration of the space shuttle orbiter. The primary test objectives were to obtain incremental data on the effects of a sting mount on base pressures and force and moment data. The increments obtained included the addition of MPS nozzles as well as the deletion of the simulated sting mount. Six-component aerodynamic force and moment data were recorded over an angle of attack range from 12 to 42 degrees at 0 and 5 degrees angles of sideslip. The testing was accomplished at Mach 5.3 and Mach 10.3. The effects of various elevon, body flap, and speed brake settings were investigated, and static pressures were measured at the fuselage base for use in force-data reduction.

Milam, M. D.↗
NASA NTRS1975

Results of an external tank separation test in AEDC/VKF tunnel B on 0.010-scale replica of space shuttle vehicle model 52-OT(IA17A), Volume 1

Tests were conducted on scale models of the space shuttle orbiter and external tank (ET) to determine the aerodynamic interactions during a return to launch site abort separation. The orbiter model was built to vehicle 3 configuration lines (139B) and the ET model approximated the vehicle 5 configurations with protuberances and attach hardware. For these investigations the orbiter was mounted on the primary support system and the external tank was mounted on the captive trajectory system. Six-component data were obtained for each vehicle at various orbiter angles of attack and sideslip for a range of relative angular and linear displacements of the ET from the orbiter.

Spangler, R. H.↗
NASA NTRS1975

The relationship between reliability and bonding techniques in hybrid microcircuits

Differential thermal expansion was shown to be responsible for many observed failures in ceramic chip capacitors mounted on alumina substrates. It is shown that the mounting techniques used in bonding the capacitors have a marked effect upon the thermally induced mechanical stress and thus the failure rate. A mathematical analysis was conducted of a composite model of the capacitor-substrate system to predict the magnitude of thermally induced stresses. It was experimentally observed that the stresses in more compliant bonding systems such as soft lead tin and indium solders are significantly lower than those in hard solder and epoxy systems. The marked dependence upon heating and cooling rate was proven to be a determining factor in the prediction of failure solder systems. It was found that the harder or higher melting solders are less susceptible to thermal cycling effects but that they are more likely to fail during initial processing operations. Strain gage techniques were used to determine thermally induced expansion stresses of the capacitors and the alumina substrates. The compliance of the different bonding mediums was determined. From the data obtained, several recommendations are made concerning the optimum bonding system for the achievement of maximum reliability.

Caruso, S. V.↗
NASA NTRS1974

Airborne infrared astronomy telescope

Description of a 91.5-cm (36-in.) airborne infrared telescope installed in a C141A StarLifter as a national IR observatory. The telescope system is mounted in a specially constructed cavity located just ahead of the leading edge of the wing. All controls and ancillary systems are located in consoles and racks mounted aft of the telescope. The telescope is a conventional Cassegrain design which can be used either directly with the focal point behind the primary mirror or in a folded configuration by inserting a tertiary mirror following the secondary which folds the optical path through the support bearing into the aircraft cabin area. The telescope system is designed to operate at all ambient conditions from sea level to 15,200 m. The system is optimized for operation at ambient temperatures experienced at 13,000 to 15,000 m (220 K). The entire telescope assembly with the exception of noncritical covers and brackets is constructed of Invar-type material to minimize the effects of thermal distortions. Pointing accuracy and stability of the telescope with respect to the target are achieved through multiple stages of stabilization and vibration isolation equipment.

Cameron, R. M.↗
NASA NTRS1975

Transonic buffet behavior of Northrop F-5A aircraft

Flight tests were performed on an extensively instrumented F-5A aircraft to investigate the dynamic buffet pressure distribution on the wing surfaces and the responses during a series of transonic maneuvers called the windup turns. The maneuvers to maximum lift were performed at three Mach number-altitude combinations with a constant 'q' of approximately 14,360 N/sq m (300 psf). The fluctuating buffet pressure data at 24 stations on the right wing of the F-5A were acquired by miniaturized semiconductor type pressure transducers mounted on the wing. A new transducer mounting and wiring technique was applied where the interference with the natural flow condition was minimized. The data acquired in this manner were found adequate to trace the shock origin, the movement of the shock front and the development of the separated flow (shock induced or leading edge induced) on the wing surface.

Hwang, C.↗
NASA NTRS1974

Vegetation and soil backscatter over the 4-18 GHz region

Using an FM-CW radar mounted atop a truck-mounted boom, 4-8 GHz backscatter spectral data was gathered during the 1972 growing season at incidence angles of 0-70 deg in 10 deg steps for each of the four linear polarization combinations. The data covers four mature crop types (corn, milo, soybeans and alfalfa) and bare ground taken under a wide range of soil and plant moisture contents. To insure statistical representation of the results, measurements were conducted over 147 fields corresponding to a total of about 50,000 data points. During 1973, a higher frequency version of the above system was used to collect additional data over the 8-18 GHz frequency region. This paper presents a summary of the results and suggests design criteria for future radar remote sensing missions.

Ulaby, F. T.↗
NASA NTRS1975

Pyrotechnic shock measurement and data analysis requirements

A study of laboratory measurement and analysis of pyrotechnic shock prompted by a discrepancy in preliminary Mariner Jupiter/Saturn shock test data is reported. It is shown that before generating shock response plots from any recorded pyrotechnic event, a complete review of each instrumentation and analysis system must be made. In addition, the frequency response capability of the tape recorder used should be as high as possible; the discrepancies in the above data were due to inadequate frequency response in the FM tape recorders. The slew rate of all conditioning amplifiers and input converters must be high enough to prevent signal distortion at maximum input voltage; amplifier ranges should be selected so that the input pulse is approximately 50% of full scale; the Bessel response type should be chosen for digital shock analysis if antialiasing filters are employed; and transducer selection must consider maximum acceleration limit, mounted resonance frequency, flat clean mounting surfaces, base bending sensitivity, and proper torque.

Albers, L.↗
NASA NTRS1975

The relationship between reliability and bonding techniques in hybrid systems

Differential thermal expansion has been shown to be responsible for many observed failures in ceramic chip capacitors mounted on alumina substrates. The present work has shown that the mounting techniques used in bonding the capacitors have a marked effect upon the thermally induced mechanical stress and thus the failure rate. A mathematical analysis of a composite model of the capacitor-substrate system to predict the magnitude of thermally induced stresses have been conducted. It has been experimentally observed that the stresses in more compliant bonding systems such as soft lead/tin and indium solders are significantly lower than those in hard solder and epoxy systems. From the data obtained, several recommendations are made concerning the optimum bonding system for the achievement of maximum reliability.

Kinser, D. L.↗
NASA NTRS1975

Spacecraft detumbling using movable telescoping appendages

The dynamics of detumbling a randomly spinning spacecraft using externally mounted, movable telescoping appendages are studied both analytically and numerically. Two types of telescoping appendages are considered: (1) where an end mass is mounted at the end of an (assumed) massless boom; and (2) where the appendage is assumed to consist of a uniformly distributed homogeneous mass throughout its length. From an application of Liapunov's second method boom extension maneuvers can be determined to approach either of two desired final states: close to a zero inertial angular velocity state, and a final spin rate about only one of the principal axes. Recovery dynamics are evaluated analytically for the case of symmetrical deployment. Numerical examination of other asymmetrical cases verifies the practicality of using movable appendages to recover a randomly tumbling spacecraft.

Bainum, P. M.↗
NASA NTRS1975

Low-noise room-temperature and cryogenic mixers for 80-120 GHz

A description is given of two new mixers designed to operate in the 80-120-GHz range on 36-ft radio telescope. It is shown that for a hard-driven diode the parasitic resistance and capacitance are the primary factors influencing the design of the diode mount. A room-temperature mixer is described which achieves a single-sideband (SSB) conversion loss (L) of 5.5 dB, and a SSB noise temperature (Tm) of 500 K (excluding the IF contribution) with a 1.4-GHz IF. A cryogenically cooled version, using a quartz structure to support the diode chip and contact whisker, achieves values of L = 5.8 dB and Tm = 300 K with a 4.75-GHz IF. The mixers use high-quality Schottky-barrier diodes in a one-quarter-height waveguide mount.

Kerr, A. R.↗