Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “L REACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Magnetite nanoparticle anchored graphene cathode enhances microbial electrosynthesis of polyhydroxybutyrate by Rhodopseudomonas palustris TIE-1

Microbial electrosynthesis (MES) is an emerging technology that can convert carbon dioxide (CO 2 ) into value-added organic carbon compounds using electrons supplied from a cathode. However, MES is affected by low product formation due to limited extracellular electron uptake by microbes. Herein, a novel cathode was developed from chemically synthesized magnetite nanoparticles and reduced graphene oxide nanocomposite (rGO-MNPs). This nanocomposite was electrochemically deposited on carbon felt (CF/rGO-MNPs), and the modified material was used as a cathode for MES production. The bioplastic, polyhydroxybutyrate (PHB) produced by Rhodopseudomonas palustris TIE-1 (TIE-1), was measured from reactors with modified and unmodified cathodes. Results demonstrate that the magnetite nanoparticle anchored graphene cathode (CF/rGO-MNPs) exhibited higher PHB production (91.31 ± 0.9 mg l -1 ). This is ~4.2 times higher than unmodified carbon felt (CF), and 20 times higher than previously reported using graphite. This modified cathode enhanced electron uptake to -11.7 ± 0.1 μ A cm -2 , ~5 times higher than CF cathode (-2.3 ± 0.08 μ A cm -2 ). The faradaic efficiency of the modified cathode was ~2 times higher than the unmodified cathode. Electrochemical analysis and scanning electron microscopy suggest that rGO-MNPs facilitated electron uptake and improved PHB production by TIE-1. Overall, the nanocomposite (rGO-MNPs) cathode modification enhances MES efficiency.

Materials Science↗

Performance of alumina-supported Pt catalysts in an electron-beam-sustained CO2 laser amplifier

The performance of an alumina-supported Pt catalyst system used to maintain the gas purity in an electron-beam-sustained (636) isotope CO2 laser amplifier has been tested. The system characteristics using the two-zone, parallel flow reactor were determined for both continuous- and end-of-day reactor operation using on-line mass spectrometric sampling. The laser amplifier was run with an energy loading of typically 110 J-l/atm and an electron-beam current of 4 mA/sq cm. With these conditions and a pulse repetition frequency of 10 Hz for up to 10,000 shots, increases on the order of 100 ppm O2 were observed with the purifier on and 150 ppm with it off. The 1/e time recovery time was found to be approximately 75 minutes.

Cunningham, D. L.↗

Mark-18A Target Material Recovery Program: Initial Hot Startup

The Savannah River National Laboratory (SRNL) has been tasked by the National Nuclear Security Administration to recover highly valued isotopes from irradiated Mark-18A (Mk-18A) targets. The Savannah River Site (SRS) has sixty-five Mk-18A targets available for the recovery of the high valued materials. The Mk-18A targets were manufactured with Pu-242 then irradiated under high neutron flux in K-Reactor at the SRS from 1968 to 1978. The sixty-five Mk-18A targets are currently stored in the SRS L-Area Basin and will be removed one at a time and individually transported to SRNL. Upon receipt at SRNL, the Mk-18A target material will be removed from the confinement, dissolved, chemically separated, and calcined to a stable oxide. The flowsheet is designed to recover the plutonium as well as the trivalent actinides. The original targets were manufactured with varying quantities of Pu-242, ranging from 5.2 grams to 121.5 grams. Taking a graded approach to process start up, the lowest loaded target (FT-80-03) was selected as the first target to be received and processed at SRNL. As operational experience and knowledge is gained from processing targets, higher loaded targets will be selected for processing to increase the quantities of valuable isotopes recovered. Due to dose concerns, the receipt and processing of the Mk-18A targets is performed in the SRNL Shielded Cells Facility. The targets are stored in a double J-can confinement in the L-Area Basin. A specially designed cask was procured for transport of the targets from L-Area to SRNL. Once received at SRNL, the targets are loaded into the back of Cell 7 and resized as they enter the cell. The resized targets (1/4 length) are then processed one at a time through the following processes: caustic dissolution and filtration, acidic dissolution and filtration, elutable Reillex anion exchange, diglycolamide (DGA) resin extraction, and DGA calcination. This processing results in two product streams. The first is an aqueous plutonium solution which is removed from the shielded cells and taken to a glovebox for further purification and conversion to an oxide. The second is a calcined oxide product containing the Am and Cm as well as other lanthanide fission products which is removed from the shielded cells using a bagless transfer system. Both materials are packaged for shipment to Oak Ridge National Laboratory (ORNL). This paper will discuss the operating experience, lessons learned, and results from initial process hot startup.

Armstrong, Christopher [Savannah River National La↗

The FREYA project at VENUS-F - the next step towards MYRRHA

The VENUS-F reactor is a fast, zero-power research reactor. Since 2009 it has used 30% wt. metallic uranium as fuel and solid lead as reflector and coolant simulator. It can also be coupled to a particle accelerator with a neutron producing target and make up a subcritical Accelerator Driven System (ADS). Within the currently ongoing FREYA project, the main tasks being investigated are the validation of online reactivity monitoring of an ADS, the validation of nuclear data and neutronic codes, and the experimental characterization of fast critical and subcritical cores representative for MYRRHA. MYRRHA will be an ADS demonstrator with the option to be operated in critical mode too. So far the only critical core at VENUS-F was assembled using 97 fuel assemblies, each of them consisting of 9 U and 16 Pb rodlets. The core was thoroughly characterized: flux traverses, spectral indices, control rod worth, delayed neutron parameters were measured and compared with Monte Carlo and deterministic calculations. A sensitivity study was also performed focusing on the influence of material impurities, positioning uncertainties, structures and detectors around the core. It was a simple core without any perturbations in the active zone. In the next critical cores that are planned to be investigated in 2015 and 2016, additional elements will be introduced in order to become more representative for MYRRHA. As MYRRHA will use MOX fuel, oxygen will be added into the following core. This will be done by introducing Al{sub 2}O{sub 3} into the fuel assemblies. New fuel assemblies have been already made and are ready to be loaded. Each consists of 13 U, 8 Pb, and 4 Al{sub 2}O{sub 3} rodlets. The new critical core will consist of approximately 40 such fuel assemblies and will be loaded in January 2015. The first results of the characterization measurements will be presented. Additionally, it is planned to investigate coolant void effects. As MYRRHA will be a rather complex system using a number of in-pile sections and heterogeneous elements inside and around the active zone, the next cores will be step by step modified by loading new materials and perturbations with the aim to assemble a MYRRHA mock-up. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Spectral indices measurements using miniature fission chambers at the MINERVE zero-power reactor at CEA using calibration data obtained at the BR1 reactor at SCK.CEN

Spectral indices are parameters of major importance to characterize a multiplying medium and to evaluate performances of neutronics calculation tools as well as quality of associated nuclear data. Experiments performed in 2004 at the CEA MINERVE facility loaded with the R1-UO{sub 2} lattice [1], using homemade miniature fission chambers and calibration data acquired at the SCK.CEN BR1 facility in 2001 [2], resulted in ambivalent conclusions. On one hand, spectral indices involving only fissile isotopes gave relevant results and consistent discrepancies between calculation and experiment. On the other hand, spectral indices involving both fissile and fertile isotopes showed inconsistent results depending on the type of calibration data used. In particular, the {sup 238}U(n,f)/{sup 235}U(n,f) spectral indices resulted in values far from the calculations in all cases. In 2004, those differences between measurement and calculation were mainly attributed to an imprecise knowledge of the isotopic composition of the deposits loaded in the {sup 238}U chambers. At that time, priorities in the development of programs in MINERVE and other considerations about the manufacturing and calibration of new fission chambers did not allow to further investigate these discrepancies. In 2009, the preparation of a new program at the EOLE facility [1] and changes in the regulatory framework for management of fission chambers motivated the manufacturing of new detectors. At the same time, the re-installation of the R1-UO{sub 2} lattice in MINERVE gave the opportunity to carry out a new spectral indices measurement campaign. Nevertheless, although the isotopic composition of active deposits was better known than previously, the comparison between experimental results and calculations still resulted in inconsistent discrepancies. A sensitivity study indicated afterwards that, among all parameters to be considered for the analysis and the assessment of final uncertainty, calibration data have the greatest impact. In April 2010, a new calibration campaign conducted again at the BR1 facility allowed the CEA to reanalyze the spectral indices measurements performed in 2009. With this new set of calibration data, the experimental values of spectral indices finally matched the calculation results within the uncertainty margins. In addition, the confrontation of data from 2001 and 2010 calibration campaigns, both performed with the same experimental conditions, allowed to shed on the light dead time correction issues in the monitoring of calibration measurements. At the end, this also explained the inconsistencies observed during the 2004 campaign. This paper first, presents the two different analysis methods for getting the experimental value of a spectral index and, lists main parameters that influence the determination of the experimental value. It then details the calibration processes that are set-up at the MINERVE and BR1 facilities, describes the various experiments carried out and finally comments the results obtained. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Neutrino-4 experiment on the search for a sterile neutrino at the SM-3 reactor

In view of the possibility of the existence of a sterile neutrino, test measurements of the dependence of the reactor antineutrino flux on the distance from the reactor core has been performed on SM-2 reactor with the Neutrino-2 detector model in the range of 6–11 m. Prospects of the search for reactor antineutrinos at short distances have been discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The neutron imaging diagnostic at NIF (invited)

A neutron imaging diagnostic has recently been commissioned at the National Ignition Facility (NIF). This new system is an important diagnostic tool for inertial fusion studies at the NIF for measuring the size and shape of the burning DT plasma during the ignition stage of Inertial Confinement Fusion (ICF) implosions. The imaging technique utilizes a pinhole neutron aperture, placed between the neutron source and a neutron detector. The detection system measures the two dimensional distribution of neutrons passing through the pinhole. This diagnostic has been designed to collect two images at two times. The long flight path for this diagnostic, 28 m, results in a chromatic separation of the neutrons, allowing the independently timed images to measure the source distribution for two neutron energies. Typically the first image measures the distribution of the 14 MeV neutrons and the second image of the 6-12 MeV neutrons. The combination of these two images has provided data on the size and shape of the burning plasma within the compressed capsule, as well as a measure of the quantity and spatial distribution of the cold fuel surrounding this core.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Reliability Assessment of Remote Visual Examination

Remote visual testing (RVT) is a commonly used nondestructive examination method for inservice inspection (ISI) of reactor internals to detect cracking and gross component failures. Despite widespread use, the detection reliability of RVT and the factors that impact overall RVT performance have been unresolved issues. This report describes the results from an assessment sponsored by the U.S. Nuclear Regulatory Commission and conducted by the Pacific Northwest National Laboratory, in cooperation with the Electric Power Research Institute, for evaluating the reliability of RVT methods currently being used for [reactor] in-vessel visual inspection. The goal was to assess the performance of commercially applied RVT examination procedures implemented by qualified personnel, as well as to identify and qualitatively assess enhancements to examination procedures for detecting flaws in test specimens. The assessment was performed over three phases of research, with the results of the first phase used to identify key controllable parameters impacting RVT performance and to design the next two phases (round-robin testing). Participants in the round-robin tests included teams of inspectors from commercial nuclear power ISI vendors. Participants were asked to determine if a specimen contained a crack and its approximate location, orientation, and length. The detection and location information were used to compute estimates of the probability of detection and false call probability for various scenarios such as the placement and orientation of the flaw on the specimen, team-to-team variations in detection performance, and effects of secondary review on RVT detection. Results showed that crack opening displacement (COD) is the dominant factor in the reliability of crack detection using commercially applied RVT procedures, with crack length being weakly correlated with detection probability. The implication is that RVT detection is likely heavily dependent on the contrast produced by the crack opening, with crack detection becoming less reliable as the COD decreases. Further, the results indicated RVT will be challenged when cracks are located in the vicinity of surface features such as scratches or weld ripples, or close to the edge of welds where shadowing and/or the presence of weld undercuts may complicate the ability to detect the crack. The assessment also reinforced earlier findings on the importance of lighting in flaw detection and appeared to align with other studies that find improved reliability when using multiple inspectors or analysts. Finally, the results pointed to the importance of practice with specimens that mimic conditions likely to be found in the field. Based on the findings and limitations of the assessment, a number of recommendations are made regarding best practices for improving the reliability of RVT in a field setting and for addressing remaining informational gaps. This report describes the design and noted limitations of the three phases of research, the analysis methodology for each phase, and the results of the research. The results of this assessment provide a benchmark set of data on the reliability of RVT for detecting cracking, assuming the implementation of field-like inspection procedures. The likely impact of several uncontrolled factors on RVT detection performance are discussed, and recommendations regarding the use of these results to assess field performance are provided. Finally, recent advances in RVT technology are briefly discussed and point to the potential need for continued research to evaluate the capability and effectiveness of the technique as improvements are implemented.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Rapid Analytical Methodology for Chloride Molten Salt Reactor Safeguards and Process Monitoring

Technologies that enable near real-time isotopic analysis of advanced molten salt reactor (MSR) fuels are critically needed to safeguard these reactors, increase their operational efficiency, and enable their widespread deployment with confidence. We present a systematic approach to developing near real-time dissolution and chemical isolation of U, Pu, and major fission products from highly radioactive chloride molten salt samples. Chemical yields greater than 95% were observed for both uranium and the lanthanides. Interference reduction enabled the detection and quantification of key diagnostic isotopes (including 112Ag, 147Nd, and 153Sm) that were previously undetectable in the original sample. The results from this initial scoping study lay the foundation for the development of future automated systems that can enable cost-efficient, near-real time chemical separation and analysis of extremely highly radioactive molten salt samples.

38 - RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCL↗

Sodium Compatibility of Advanced Materials

This report gives a description of ongoing activities in the design, fabrication, construction, and planned testing of advanced structural materials in a forced convection sodium flow loop. The work is the Argonne National Laboratory (ANL) portion of the effort on the work project entitled, "Sodium Compatibility of Advanced Fast Reactor Materials," with Oak Ridge National Laboratory (ORNL) as the technical lead and is a part of Advanced Structural Materials Program for the Advanced Fuel Cycle Initiative (AFCI) Reactor Campaign. The objective of this project is to develop information on sodium corrosion compatibility of advanced materials being considered for sodium reactor applications. This report is the third deliverable from ANL in FY09 (M3505050704) under the work package “Sodium Compatibility of Advanced Fast Reactor Materials.” An earlier report examined the thermodynamic and kinetic factors involved in the purity of liquid sodium coolant for sodium reactor applications. Available information was presented on solubility of several metallic and nonmetallic elements along with a discussion of the possible mechanisms for the accumulation of impurities in sodium. That report concluded that the solubility of many metals in sodium is low (<1 part per million) in the temperature range of interest in sodium reactors and such trace amounts would not impact the mechanical integrity of structural materials and components. The earlier report also analyzed the solubility and transport mechanisms of nonmetallic elements such as oxygen, nitrogen, carbon, and hydrogen in laboratory sodium loops and in reactor systems such as Experimental Breeder Reactor-II (EBR-II), Fast Flux Test Facility (FFTF), and Clinch River Breeder Reactor (CRBR). Among the nonmetallic elements discussed, oxygen is deemed controllable and its concentration in sodium can be maintained in sodium for long reactor life by using cold-trap method. It was concluded that among the cold-trap and getter-trap methods, the use of cold trap is sufficient to achieve oxygen concentration of the order of 1 part per million. Under these oxygen conditions in sodium, the corrosion performance of structural materials such as austenitic stainless steels and ferritic steels will be acceptable at a maximum core outlet sodium temperature of ≈550°C. In the current sodium compatibility studies, the oxygen concentration in sodium will be controlled and maintained at ≈1 ppm by controlling the cold trap temperature. Among the nonmetallic elements in sodium, carbon was assessed to have the most influence on structural materials since carbon, as an impurity, is not amenable to control and maintenance by any of the simple purification methods. The dynamic equilibrium value for carbon in sodium systems is dependent on several factors, details of which were discussed in the earlier report. Furthermore, the transport of carbon in the primary and secondary loops of the reactor system and its effect on the carburization-decarburization behavior of structural components was addressed. Based on this assessment, the current sodium compatibility studies will examine the role of carbon concentration in sodium on the carburization-decarburization of advanced structural materials at temperatures up to 650°C. Carbon will be added to the sodium by exposure of carbon-filled iron tubes, which over time will enable carbon to diffuse through iron and dissolve into sodium. The method enables addition of dissolved carbon (without carbon particulates) in sodium that is of interest for materials compatibility evaluation. The removal of carbon from the sodium will be accomplished by exposing carbon-gettering alloys such as refractory metals that have a high partitioning coefficient for carbon and also precipitate carbides, thereby decreasing the carbon concentration in sodium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multipole mixtures in gamma transitions in the (n, n'{gamma}) reaction on {sup 160}Gd

The spectrum of gamma rays from the reaction {sup 160}Gd(n, n'{gamma}) and their angular distribution with respect to the neutron-beam axis are measured by using fast reactor neutrons. The scheme of energy levels and gamma transitions is composed for {sup 160}Gd. Multipole-mixture parameters {delta} are found for many gamma transitions.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Elucidating the Chemical Pathways Responsible for the Sooting Tendency of 1 and 2-phenylethanol

Yield Sooting Index (YSI) measurements have shown that oxygenated aromatic compounds (OACs) tend to have lower YSI than aromatic hydrocarbon (AHC) compounds. For example, typical AHCs such as toluene and ethyl benzene have a YSI of 170 and 216, respectively, in contrast, OACs such as phenol and anisole have a YSI of 81 and 111, respectively. However, this trend is not always true as was observed for the structural isomers 1-phenylethanol (1PE, YSI=142) and 2-phenylethanol (2PE, YSI=207), where 2PE contains a YSI more representative of AHCs than OACs. We applied flow reactor experiments and density functional theory (DFT) calculations to examine how oxygen functionality present in 1PE and 2PE alters the reaction pathways leading to the observed difference in soot formation. It was determined that the proximity of the oxygen functional group to the aromatic ring determines whether the oxygen remains attached to the primary reacting species (for 1PE) or is eliminated early in the combustion sequence (for 2PE). For these alcohols, preservation of the oxygen in the molecule leads to further OACs, while loss of the oxygen leads to AHCs and benzyl radical. The direct pathways to AHCs and benzyl radical result in the higher YSI observed for 2PE.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Assessment of Sensor Technologies for Advanced Reactors

Sensors and measurement technologies provide information on processes, support operations and provide indications of component health. They are therefore crucial to plant operations and to commercialization of advanced reactors (AdvRx). This report, developed by a three-laboratory team consisting of Argonne National Laboratory (ANL), Oak Ridge National Laboratory (ORNL) and Pacific Northwest National Laboratory (PNNL), provides an assessment of sensor technologies and a determination of measurement needs for AdvRx. It provides the technical basis for identifying and prioritizing research targets within the instrumentation and control (I&C) Technology Area under the Department of Energy’s (DOE’s) Advanced Reactor Technology (ART) program and contributes to the design and implementation of AdvRx concepts. The report is organized under two broad categories: High Temperature Reactors and Fast Reactors. For the purposes of this report, the scope of “High temperature reactors” includes Gen IV reactors whose coolant exit temperatures exceed ~650 °C and are moderated (as opposed to fast reactors). We included in this category gas-cooled reactors that have been built and operated throughout the world to date-including those that use carbon dioxide (CO 2 ) or Helium (He) as coolant-and the molten salt reactor. However, for the sake of conciseness this report uses the high temperature gas reactor (HTGR) as an example in many cases. With regard to fast reactors, there are several reactor years of experience with several technology variants (including sodium fast reactors and other fast reactors such as the LBFR). In particular, several experimental, prototype and demonstration units have been designed and operated in several countries, including France, India, Japan, USSR/Russia, UK, and the United States. To bound the scope, this report reviewed relevant operating experience from US-operated Sodium Fast Reactor (SFR) and relevant test experience from the Fast Flux Test Facility (FFTF).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Power Burst Facility: U(18)O2-CaO-ZrO2 Fuel Rods in Water

The Power Burst Facility (PBF) reactor operated from 1972 to 1985 on the SPERT Area I of the Idaho National Laboratory, then known as Nuclear Reactor Test Station. PBF was designed to provide experimental data to aid in defining thresholds for and modes of failure under postulated accident conditions. PBF reactor startup testing began in 1972. This evaluation focuses on two operational loading tests, chronologically numbered 1 and 2, published in a startup-test report in 1974 [1]. Data for these tests was used by one of the authors to validate a MCNP model for criticality safety purposes [2]. Although specific references to original documents are kept in the text, all the reactor parameters and test specific data presented here was adapted from that report. The tests were performed with operational fuel loadings, a stainless steel in-pile tube (IPT) mockup, a neutron source, four pulse chambers, two fission chambers, and one ion chamber. The reactor's four transition rods (TRs) and control rods (CRs) were present but TR boron was completely withdrawn below the core and CR boron was partially withdrawn above the core. Test configurations differ primarily in the number of shim rods, and consequently the number of fuel rods included in the core. The critical condition was approached by incrementally and uniformly withdrawing CR boron from the core. Based on the analysis of the experimental data and numerical calculations, both experiments are considered acceptable as criticality safety benchmarks.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Robust Processing Approach for Producing Highly Loaded Dispersion Fuels

A robust fabrication method, resulting in higher yields, to produce highly loaded U3Si2-Al dispersion fuels for converting research reactors from a high enriched to a low enriched uranium fuel needs to be developed. To reliably produce a highly loaded dispersion fuel, process changes need to be implemented where the traditional approach has experienced challenges and poor yields. The present work describes the key changes needed. Parts of the work were done with uranium silicide and parts were completed with a representative silicide surrogate. The major deviations from traditional fabrication methods are associated with a refinement in particle size distribution, method for compacting to achieve complex shapes, and welding of the aluminum picture frame used to encapsulate the fuel compact. Methods for rolling and arc melting are also discussed. By using the methods described within, fabricating a highly loaded dispersion fuel that can meet stringent fuel homogeneity and geometry requirements at higher yields and lower costs may be possible.

U3Si2, HFIR, dispersion fuel, Uranium, Research Re↗

NRIC EBR-II Test Bed Pre-Conceptual Design Report

Authorized by the Nuclear Energy Innovation Capabilities Act (NEICA), the National Reactor Innovation Center (NRIC) provides private sector technology developers access to strategic infrastructures and assets for commercial nuclear energy research, development, demonstration, and deployment activities. The mission is to support a timely and cost-effective path to the licensing and commercialization of new nuclear energy systems. To meet these needs, NRIC is developing two test beds at Idaho National Laboratory (INL). The ZPPR Test bed (ZTB) and the EBR-II Test bed (ETB). The EBR-II test bed will support the demonstration of systems that operate at less than 10 MWt. The baseline objective is for the EBR-II Dome to act as a safety significant containment structure capable of siting reactors that utilize Safeguards Category 4 material for operations. The major areas addressed in the pre-conceptual design include: • Installation of an access door • Electrical Power • Heat Removal • Ventilation in the Dome • Module handling system Along with the design for ETB a concept of operations (COP) has also been developed. The COP is intended to facilitate a common understanding of ideas, challenges, and issues. As systems continue to evolve in complexity System Engineers and Project Directors will utilize the COP to develop and sustain a common vision of the system for stakeholders.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

SCALE capabilities for high temperature gas-cooled reactor analysis

The SCALE code system’s ability to address stochastic distributions of fuel particles within a graphite matrix has been revisited in both multigroup (MG) features and continuous-energy (CE) Monte Carlo methods. Furthermore, this paper describes current and emergent SCALE capabilities within the CSAS sequence to address double-heterogeneous systems and presents verification and validation studies of these methods and data. Good agreement was obtained for a high temperature gas-cooled reactor (HTGR) fuel pebble model between CSAS MG eigenvalue calculations and corresponding CE reference solutions. Code-to-code comparisons for this HTGR pebble model showed good agreement of CSAS-KENO and CSAS-Shift CE calculations and the Serpent and MCNP codes in terms of eigenvalues and reaction rate ratios. Validation studies based on two HTGR experiments resulted in good agreement between MG and CE results, as well as between experiment and calculation, although the level of agreement was significantly influenced by the applied ENDF/B nuclear data library.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Microstructural Characterization of In-reactor Corrosion Tested Hastelloy N{sup R} and 316 Stainless Steel

The success of the Molten Salt Reactor Experiment (MSRE) at the Oak Ridge National Laboratory (ORNL) in the period 1950's-70's has rekindled the interested in molten salt-cooled reactors. The most recent form of this type of reactor, the Fluoride salt-cooled High-temperature nuclear Reactors (FHRs) is emerging as a leading reactor concept for the next generation nuclear reactors because it offers, among other benefits, a high degree of passive safety, high thermal efficiency, and low spent fuel. Since 2011, two three-year Integrated Research Projects (IRPs) were awarded by the U. S. Department of Energy (DoE) to the Massachusetts Institute of Technology (MIT) in partnership with the University of California, Berkeley and the University of Wisconsin-Madison to develop a 'path forward' for the development of the FHR. One primary challenge in these projects is to evaluate the corrosion and compatibility of structural alloys in the potential primary coolant of molten Li{sub 2}BeF{sub 4} (FLiBe) salt at 700 deg. C in a neutron irradiation environment. In support of structural materials development for the FHR, the static in-reactor corrosion tests of two promising alloys, nickel-based Hastelloy N{sup R} and 316 stainless steel, in {sup 7}Li-enriched molten FLiBe have been conducted in both metal-lined and graphite crucibles in the MIT nuclear research reactor in 2013. This work focuses on the microstructural characterization of the in-reactor corrosion tested alloys for understanding of their performance in high-temperature molten FLiBe salt. Our preliminary results indicate significant thermal effects, graphite effects, and irradiation effects on the alloys' performance in high-temperature molten FLiBe salt, particularly for the in-reactor corrosion tests. The neutron irradiation induces tritium generation in molten salt which could combine with fluorine ions to form corrosive HF to dramatically attack alloys. Additionally, the neutron irradiation introduces structural defects into alloys which probably alter alloys' corrosion resistivity to high temperature molten FLiBe salt. The effect of graphite on the alloys' corrosion in a nuclear reactor is also possibly different from the out-of-reactor corrosion. All these issues will be better understood by characterizing the microstructure of in-reactor corrosion tested alloy samples in our near future plans. The experimental data in this study provides valuable input for evaluating structural materials performance in the FHR. (authors)

36 MATERIALS SCIENCE↗