Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Influence of Mixed Mode I-Mode II Loading on Fatigue Delamination Growth Characteristics of a Graphite Epoxy Tape Laminate

Mixed mode I-mode II interlaminar tests were conducted on IM7/8552 tape laminates using the mixed-mode bending test. Three mixed mode ratios, G(sub II)/G(sub T) = 0.2, 0.5, and 0.8, were considered. Tests were performed at all three mixed-mode ratios under quasi-static and cyclic loading conditions, where the former static tests were used to determine initial loading levels for the latter fatigue tests. Fatigue tests at each mixed-mode ratio were performed at four loading levels, Gmax, equal to 0.5G(sub c), 0.4G(sub c), 0.3G(sub c), and 0.2G(sub c), where G(sub c) is the interlaminar fracture toughness of the corresponding mixed-mode ratio at which a test was performed. All fatigue tests were performed using constant-amplitude load control and delamination growth was automatically documented using compliance solutions obtained from the corresponding quasi-static tests. Static fracture toughness data yielded a mixed-mode delamination criterion that exhibited monotonic increase in Gc with mixed-mode ratio, G(sub II)/G(sub T). Fatigue delamination onset parameters varied monotonically with G(sub II)/G(sub T), which was expected based on the fracture toughness data. Analysis of non-normalized data yielded a monotonic change in Paris law exponent with mode ratio. This was not the case when normalized data were analyzed. Fatigue data normalized by the static R-curve were most affected in specimens tested at G(sub II)/G(sub T)=0.2 (this process has little influence on the other data). In this case, the normalized data yielded a higher delamination growth rate compared to the raw data for a given loading level. Overall, fiber bridging appeared to be the dominant mechanism, affecting delamination growth rates in specimens tested at different load levels and differing mixed-mode ratios.

Ratcliffe, James G.↗
NASA NTRS2019

Observations of Non-Spherical, Graphite-Epoxy Projectiles Impacting a Thermally-Insulated, Double-Wall Shield

The DebriSat hypervelocity impact experiment, performed at the Arnold Engineering Development Center (U.S.A.F. Arnold Air Force Base), is intended to update the catastrophic break-up models for modern satellites. To this end, the DebrisSat was built with many modern materials including structural panels of carbon-fiber, reinforced polymer (CFRP). Subsequent to the experiment, fragments of the DebrisSat have been extracted from porous, catcher panels used to gather the debris from the impact event. Thus far, one of the key observations from the collected fragments is that CFRP represents a large fraction of the fragments and that these fragments tend to be thin, flake-like structures or long, needle-like structures; whereas, debris with nearly equal dimensions is less prevalent. As current ballistic-limit models are all developed based upon spherical impacting particles, the experiment has pointed to a missing component in the current approach that must be considered. To begin to understand the implications of this observation, simulations like those shown in Fig. 1 have been performed using cylindrical structures at a representative orbital speed into an externally-insulated, double-wall shield that is representative of shielding of International-Space-Station-visiting vehicles. These simulations have been performed for normal impacts to the surface with three different angles-of-attack (AOA) to capture the effect on the shield performance. This paper documents the simulated shield and the models developed to study the effect of non-spherical fragments, as well as, derives the critical characteristics of CFRP impacting particles for the selected shield as shown in Fig. 2. To assist with the design of the updated debris models, this work summarizes the simulated results into a deployable form for evaluating the relative importance of fragment structures.

Miller, Joshua E.↗
NASA NTRS2019

Considerations of Oblique Impacts of Non-Spherical, Graphite-Epoxy Projectiles

The DebriSat hypervelocity impact experiment, performed at the Arnold Engineering Development Center, is intended to update the catastrophic break-up models for modern satellites including many modern materials like structural panels of carbon-fiber, reinforced polymer (CFRP). Subsequent to the experiment, fragments of the DebrisSat have been extracted from porous, catcher panels, and thus far, one of the key observations from the collected fragments is that CFRP represents a large fraction of the fragments and that these fragments tend to be thin, flake-like structures or long, needle-like structures pointing to the need to consider non-spherical orbital debris. Previous work examined the case of an arbitrarily oriented cylindrical projectile impacting normal to the surface of a simple double-wall, Whipple shield, with a thermal blanket on the outer surface [1]. This work extends that development using numerical simulations to oblique impacts at a representative orbital speed of 7 km/s and addresses the complexities associated with that addition.

Miller, Joshua E.↗
DOE OSTI2020

Nanofibrous electrocatalyst including nanofibrous continuous network of graphitic nanofibers having embedded catalytically active metal moieties

A nanofibrous catalyst and method of manufacture. A precursor solution of a transition metal based material is formed into a plurality of interconnected nanofibers by electro-spinning the precursor solution with the nanofibers converted to a catalytically active material by a heat treatment. Selected subsequent treatments can enhance catalytic activity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Rapid Charging Made Practical in Graphite-Based Lithium Batteries: Surface-Acoustic Wave Turbulent Electrolyte Mixing to Overcome Diffusion Limited Charging Rates

One of the key limits in rapidly recharging a lithium-ion battery is the depletion of lithium ions within the electrolyte adjacent the anode during charging and long diffusion time to overcome this depletion. It also causes dendrite formation, inefficient use of the lithium, and battery degradation over many charge-discharge cycles. Because the liquid electrolyte remains quiescent and unmixed, this depletion layer's depth rapidly grows to match the anode-cathode separation distance at even modest charge rates. The solution proposed by PI Prof. James Friend and Co-PI Prof. Ping Liu, both from the University of California, San Diego, is to mix the electrolyte and minimize the Li ion concentration gradient during charging. Even in the presence of the separator, the charging rate could then be significantly increased. They propose to accomplish this using surface acoustic wave (SAW)-driven acoustic streaming, a technique employing 10-mW fingernail-sized solid-state devices from the telecommunications industry to drive turbulent mixing to submicron length scales in a manner completely compatible with the typical 20700 and 18650 cells used in electric vehicles.

25 ENERGY STORAGE↗
DOE OSTI2021

Molecularly tunable heterogeneous catalysts by edge functionalization of graphitic carbons

Disclosed are surface immobilized (electro)catalysts that may be prepared by a condensation reaction that generates an aromatic unit that is robust to acid and base and elevated temperatures. Among their many desirable characteristics, the catalysts are far less prone to the bimolecular deactivation pathways commonly observed for homogeneous catalysts, and may be used in solvents with a range of polarities and dielectric strengths. The catalysts are suitable for a wide array of thermal catalytic reactions (polymerization, oxidation, hydrogenation, cross-coupling etc.) and as anodes and/or cathodes in fuel cells, electrolyzers, and in batteries and supercapacitors.

Surendranath, Yogesh↗