Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Analysis of the impact of the use of broad specification fuels on combustors for commercial aircraft gas turbine engines

An analytical study was conducted to assess the impact of the use of broad specification fuels with reduced hydrogen content on the design, performance, durability, emissions and operational characteristics of combustors for commercial aircraft gas turbine engines. The study was directed at defining necessary design revisions to combustors designed for use of Jet A when such are operated on ERBS (Experimental Referee Broad Specification Fuel) which has a nominal hydrogen content of 12.8 percent as opposed to 13.7 percent in current Jet A. The results indicate that improvements in combustor liner cooling, and/or materials, and methods of fuel atomization will be required if the hydrogen content of aircraft gas turbine fuel is decreased.

Szetela, E. J.↗
NASA NTRS1976

Conceptual design of reduced energy transports

The paper reports the results of a conceptual design study of new near-term fuel-conservative aircraft. A parametric study was made to determine the effects of cruise Mach number and fuel cost on the optimum configuration characteristics and relative economic performance. Supercritical wing technology and advanced engine cycles were assumed. For each design, the wing geometry was selected to maximize an economic figure of merit which reflects the potential rate of return on investment. Based on the results of the parametric study, a reduced energy configuration was selected. Compared with existing transport design, the reduced energy design has a higher aspect ratio wing with lower sweep, and cruises at a slightly lower Mach number. It yields about 30% more seat-miles/gal than current wide-body aircraft. At the higher fuel costs anticipated in the future, the reduced energy design has about the same economic performance as existing designs with the same technology level. As an example of a far-term technology application, a design with a composite material wing was also investigated.

Ardema, M. D.↗
NASA NTRS1957

Altitude Performance of a Turbojet Engine Using Pentaborane Fuel

A full-scale turbojet engine having a two-stage turbine was operated with pentaborane fuel continuously for 11.5 minutes at a simulated altitude of 55,000 feet at a flight Mach number of 0.8. The engine incorporated an NACA combustor designed specifically for use with pentaborane fuel. The specific fuel consumption was initially reduced 32 percent below that obtained with gasoline fuel; however, the occurrence of a 25-percent reduction in net thrust after 8 minutes of operation resulted in a subsequent increase in specific fuel consumption to a value only 11.5 percent lower than that for gasoline.

FUELS-RELATION TO ENGINE PERFORMANCE↗
DOE OSTI2021

Tailoring catalyst layer structures for anion exchange membrane fuel cells by controlling the size of ionomer aggreates in dispersion

The development of anion exchange membranes and ionomers plays a critical role in performance of anion exchange membrane fuel cells. However, the optimal design of catalyst layer structures still remains unexplored despite its significance. Herein, the rational design guide is presented for cathode and anode catalyst layers using m-TPN1 ionomer by controlling the size of ionomer aggregates in dispersion and comparing various catalyst layer structures. The size of m-TPN1 aggregates decreases, creating a more uniform ionomer distribution and a larger triple-phase-boundary. As ionomer distribution of the cathode catalyst layer becomes more uniform, the power density of membrane-electrode-assembly is enhanced. Also, the power density at fully humidified condition strongly correlates with the porosity of anode catalyst layer due to the limitation of hydrogen transport at anode by water flooding.

42 ENGINEERING↗
DOE OSTI2023

Multiphysics analysis of fuel Fragmentation, Relocation, and dispersal Susceptibility–Part 2: High-Burnup Steady-State operating and fuel performance conditions

The US nuclear industry is pursuing increased cycle lengths and increasing the peak rod-averaged burnup in an effort to increase the economic viability of the US nuclear fleet. Increasing burnup will afford economic viability by enabling utilities to optimize core designs to reduce the number of fresh fuel assemblies per cycle and allow nuclear power plants to operate for a longer period of time. Longer operating periods will also decrease the number of outages experienced by a nuclear power plants and, therefore, offer utilities significant operational savings. However, extending the peak rod-averaged burnup beyond 62 GWd/tU results in operating fuel rods to higher burnup under higher power conditions. This operating regime is expected to result in higher fuel temperatures, fission gas release (FGR), and rod internal pressures (RIPs) that may challenge historical safety basis and affect high-burnup (HBU) experimental testing. In particular, these conditions directly affect fuel fragmentation, relocation, and dispersal (FFRD) susceptibility, so understanding the pretransient operating conditions is critical for developing test plans that evaluate the FFRD and develop strategies to mitigate it. This paper evaluates the operating conditions and fuel performance of HBU (greater than62 GWd/tU rod average) fuel. Additionally, it investigates fuel performance sensitivities and discusses the effect on fuel performance. Here, this work used two codes. Virtual Environment for Reactor Applications (VERA) was used to calculate steady-state power histories, identify HBU operating conditions using 10 different realistic HBU core designs, and down-select rods to a representative subset of fuel rods for subsequent BISON evaluation. The BISON fuel performance code was used to investigate steady-state HBU operating conditions and assess uncertainties associated with FGR and its effect on fuel temperatures and RIPs. The VERA and BISON results will provide direct input for HBU experimental testing and support subsequent TRACE and BISON transient fuel performance analyses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Chromium-doped uranium dioxide fuels: A review

UO 2 doped with parts per million CR 2 O 3 powder is considered a potential near term accident tolerant fuel candidate. Here, the results of decades of industry and academic research into Cr-doped UO 2 are analyzed and their shortcomings are critiqued. Focusing on the incorporation mechanisms of Cr into the fuel matrix, we explore a mechanistic understanding of the characteristic properties of Cr-doped UO 2 , notably, enhanced fission gas retention attributed to enlarged grain sizes following sintering, along with marginal improvements in the thermophysical properties. The findings of recent X-ray Adsorption Near Edge Spectroscopy studies were compared and put into conversation with historic data regarding the incorporation of Cr in UO 2 . On the basis of defect mechanisms, the case is made for the substitutional incorporation of Cr governing the lattice solubility but not the enhanced U diffusivity. Instead, Cr/CR 2 O 3 redox chemistry in a well-defined oxygen potential explains the differences in the U diffusivity and O/M ratio. The primary mechanism of doping enhanced grain growth is found to be liquid assisted sintering due to a CRO (1) eutectic phase at the grain boundaries. The role of inhomogeneities in Cr concentration in UO 2 at various length scales across the materials microstructure is highlighted and connected to promising experimental and modeling work to fill in the gaps in the current understanding of Cr-doped UO 2 . The review considers both the open scientific questions and engineering applications to illustrate the deep connections between the practice and theory in the design of accident tolerant nuclear fuels. In conclusion, the review ends with an outline of future works that combine meticulous irradiation studies and high resolution experiments with next generation modeling and simulations techniques empowered by machine learning advances to accelerate the fabrication and adoption of Cr-doped UO 2 light water reactors.

Cleveland, Mack Wesley [Massachusetts Inst. of Tec↗
DOE OSTI2020

Structures, Systems, and Components Classification Criteria for the Versatile Test Reactor

The Versatile Test Reactor (VTR) is a fast spectrum test reactor currently being developed in the United States under the direction of the US Department of Energy (DOE), Office of Nuclear Energy. The VTR mission is to enable accelerated testing of advanced reactor fuels and materials required for advanced reactor technologies. The conceptual design of the 300 MWth sodium-cooled metallic-fueled pool-type fast reactor has been led by the U.S. National Laboratories in collaboration with General Electric-Hitachi and Bechtel National Inc. As part of the VTR authorization process by the DOE, it is necessary to identify the safety classification of structures, systems, and components (SSCs) to determine the proper design, surveillance, operation, and incident-reporting requirements. Since VTR is utilizing a risk-informed, performance-based authorization process based on the Licensing Modernization Project (LMP) described in NEI 18-04 [1], the criteria for SSC classification, which are reviewed here, includes both risk information from the probabilistic risk assessment (PRA) and prescriptive requirements.

Grabaskas, David↗
DOE OSTI2025

Diffusion behavior of lanthanide fission products in bcc Fe cladding: A first-principles study

Fuel-cladding chemical interaction poses significant challenges in nuclear reactors, where fission products generated from nuclear fuel interact with Fe-based cladding materials, potentially compromising their structural integrity. This study investigates the diffusion behavior of lanthanide fission products, Lanthanum (La), Cerium (Ce), Praseodymium (Pr), and Neodymium (Nd), within body-centered cubic (bcc) Fe cladding using the density functional theory, nudged elastic band method, and self-consistent mean field theory. Our results reveal significant vacancy binding energies, particularly with the 1st and 2nd nearest neighbors, which diminish beyond the 5th nearest neighbor, with La exhibiting the strongest binding affinity, followed by Nd, Ce, and Pr. The nudged elastic band calculations indicate significant high barriers for the dissociation of 1st nearest neighbor vacancy-solute pairs for all fission products. The tracer diffusion coefficients of these fission products were derived in an Arrhenius form, with a magnetic correction that accounts for the high-temperature paramagnetic state. The significant trapping effect of vacancies caused by a very dilute concentration of fission products reduces vacancy mobility, potentially leading to modifications in point defect supersaturation, void nucleation, and swelling under irradiation. These represent critical challenges for irradiated cladding materials. The tracer diffusion coefficients indicate that Nd diffuses the fastest, followed by La, Ce, and Pr. Furthermore, this study provides essential insights for understanding fission product transport in cladding materials and informs future design strategies to mitigate fuel-cladding chemical interaction, ultimately enhancing nuclear reactor safety and performance.

Diffusion↗
DOE OSTI2022

Fusion Fuel Cycle Inventory Reduction Studies Using a Processing-Time–Based Discrete-Time Interval Model

Developing a Fusion Pilot Plant (FPP) design that minimizes risks due to tritium in-process inventory (IPI) is an important concern for the operation of commercial devices. This becomes even more of concern since an FPP will be breeding more tritium than is burned in the reactor for sustainability. The IPI is the tritium moving through the system that is not in the storage and delivery subsystem. Here a process model that solves time-dependent differential equations based on processing times was used to investigate the reduction of the IPI of a potential fuel cycle design. The impact of new and more efficient technologies such as direct internal recycling (DIR), metal foil pumps, continuous pumping, improved isotope separation, and hydrogen separating continuous pumps on IPI was investigated by adjusting subsystem processing times and material flow streams. It was shown that any of the insertions of DIR studied in this paper caused a reduction in the total IPI of the system and proved to be the optimal way to reduce the IPI in the system. Fuel cycle modifications near the torus, such as a coupled DIR and improved pumping systems, produced the largest reductions in tritium inventory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Microgrid Tiered Circuits Effects for a Planned Housing Community in Puerto Rico

Puerto Rico faced a double strike from hurricanes Irma and Maria in 2017. The resulting damage required a comprehensive rebuild of electric infrastructure. There are plans and pilot projects to rebuild with microgrids to increase resilience. This paper provides a techno-economic analysis technique and case study of a potential future community in Puerto Rico that combines probabilistic microgrid design analysis with tiered circuits in building energy modeling. Tiered circuits in buildings allow electric load reduction via remote disconnection of non-critical circuits during an emergency. When coupled to a microgrid, tiered circuitry can reduce the chances of a microgrid's storage and generation resources being depleted. The analysis technique is applied to show 1) Approximate cost savings due to a tiered circuit structure and 2) Approximate cost savings gained by simultaneously considering resilience and sustainability constraints in the microgrid optimization. The analysis technique uses a resistive capacitive thermal model with load profiles for four tiers (tier 1-3 and non-critical loads). Three analyses were conducted using: 1) open-source software called Tiered Energy in Buildings and 2) the Microgrid Design Toolkit. For a fossil fuel based microgrid 30% of the total microgrid costs of 1.18 million USD were calculated where the non-tiered case keeps all loads 99.9% available and the tiered case keeps tier 1 at 99.9%, tier 2 at 95%, tier 3 at 80% availability, with no requirement on non-critical loads. The same comparison for a sustainable microgrid showed 8% cost savings on a 5.10 million USD microgrid due to tiered circuits. The results also showed 6-7% cost savings when our analysis technique optimizes sustainability and resilience simultaneously in comparison to doing microgrid resilience analysis and renewables net present value analysis independently. Though highly specific to our case study, similar assessments using our analysis technique can elucidate value of tiered circuits and simultaneous consideration of sustainability and resilience in other locations.

building energy modeling↗
DOE OSTI2025

Surface Chemistry and Particle Morphology Changes in Pine Biomass under Indirect Thermal Gradients: Implications for Feed Screw Design

The conversion of biomass feedstocks into fuels and chemicals using fast pyrolysis is a promising approach to renewable energy. Feed screws that convey biomass to pyrolysis reactors, however, often encounter plugging. Indirect heating of the feed screw occurs due to contact with the pyrolysis chamber, resulting in a heating gradient ranging from ambient temperature (22 °C) to reactor temperature (500 °C). Given that major cell wall macromolecules, such as lignin, cellulose, and hemicellulose, begin to produce bio-oils and volatile resin acid compounds within this temperature gradient, we hypothesized that indirect heating during feed screw conveyance is sufficient to cause premature degradation of biomass. We characterized this degradation by observing increases in surface roughness, changes in overall particle morphology, and the production and deposition of bio-oils on biomass particle surfaces. Correlative analysis between optical in situ hot-stage microscopy, confocal Raman spectroscopy, and SEM analysis revealed that heating at temperatures as low as 375 °C caused significant increases in surface roughness, with large fissures forming between and within cell walls. Additionally, droplets of bio-oil were observed on particles, especially in the bark and cambium samples. This work suggests that these phenomena contribute to particle agglomeration, leading to feed screw plugging, and that engineering a solution to cool the feed screw could prevent particle agglomeration and reduce plugging incidents, thereby increasing biomass processing efficiency.

09 BIOMASS FUELS↗
NASA NTRS1980

High-density fuel combustion and cooling investigation

The analysis, design, fabrication and testing of several engine configurations are discussed with respect to the combustion and heat transfer characteristics of LOX/RP-1 at chamber pressures between 6895 and 13790 kPa (1000 and 2000 psia). The different engine configurations discussed include: 8274 kPa and 13790 kPa (1200 psia and 2000 psia) chamber pressure injectors with like doublet and preatomized triplet elements; cooled and uncooled acoustic resonators; and graphite, regeneratively cooled and calorimetric chambers ranging in length from 27.9 to 37.5 cm (11 to 15 in.). A high pressure LOX/RP-1 spark igniter is also evaluated.

Labotz, R. J.↗
NASA NTRS1986

Coal-Based Fuel-Cell Powerplants

Report assesses advanced technologyy design alternatives for integrated coal-gasifier/fuel-cell powerplants. Various gasifier, cleanup, and fuelcell options evaluated. Evaluation includes adjustments to assumed performances and costs of proposed technologies where required. Analysis identifies uncertainties remaining in designs and most promising alternatives and research and development required to develop these technologies. Bulk of report summary and detailed analysis of six major conceptual designs and variations of each. All designs for plant that uses Illinois No. 6 coal and produces 675 MW of net power.

Ferral, J. F.↗
DOE OSTI2021

Oxy-combustion process with modular boiler design

A modular boiler system for implementing fuel combustion is provided. The system includes a first boiler and a second boiler of a plurality of boilers, an oxygen input unit, a fuel input unit, a recycled flue gas input unit, and a flue gas separator. The first boiler receives oxygen from the oxygen input unit, fuel from the fuel input unit, and recycled flue gas from the recycled flue gas input unit. The first boiler outputs intra-system flue gas. The flue gas separator separates the intra-system flue gas into a first and second flue gas stream, transfers the first flue gas stream to the second boiler, and transfers the second flue gas stream to a gas cleaning system. The second boiler receives oxygen from the oxygen input unit, fuel from the fuel input unit, and the first flue gas stream from the flue gas separator.

Axelbaum, Richard L.↗
NASA NTRS2007

NDE Development for Inspection of the Ares I Crew Launch Vehicle

NASA is designing a new crewed launch vehicle called Ares I to replace the Space Shuttle after its scheduled retirement in 2010. This new launch vehicle will build on the Shuttle technology in many ways including using a first stage based upon the Space Shuttle Solid Rocket Booster, advanced aluminum alloys for the second stage tanks, and friction stir welding to assemble the second stage. Friction stir welding uses a spinning pin that is inserted in the joint between two panels that are to be welded. The pin mechanically mixes the metal together below the melting temperature to form the weld. Friction stir welding allows high strength joints in metals that would otherwise lose much of their strength as they are melted during the fusion welding process. One significant change from the Space Shuttle that impacts NDE is the implementation of self-reacting friction stir welding for non-linear welds on the primary metallic structure. The self-reacting technique differs from the conventional technique because the load of the pin tool pressing down on the metal being joined is reacted by a nut on the end of the tool rather than an anvil behind the part. No spacecraft has ever flown with a self-reacting friction stir weld, so this is a major advancement in the manufacturing process, bringing with it a whole new set of challenges for NDE to overcome. Another impact is the proposed usage of an aluminum face sheet, phenolic honeycomb sandwich structure for a common bulkhead between the fuel and oxidizer tanks. This design was used on the second stage of Saturn IB and the second and third stages of Saturn V, but both the manufacturing and subsequent inspection were very costly and time consuming so a more efficient inspection method is sought. The current state of development of these inspections will be presented, along with other information pertinent to NDE of the Ares I.

Richter, Joel↗
DOE OSTI2023

Designing a GIS-based supply chain for producing carinata-based sustainable aviation fuel in Georgia, USA

Carinata is a potential crop for sustainable aviation fuel (SAF) production in the southern USA. However, as a novel crop, the cost-effectiveness and environmental feasibility of carinata feedstock are unknown, and there are questions about the optimal supply chain configuration for carinata-based SAF production. This study aims to design a supply chain model for carinata-based SAF production by optimizing the location of farms and facilities (e.g. storage units, crushing mills, biorefineries) for a minimum transportation cost under a set of supply and demand conditions. An integrated mixed-integer linear programming (MILP) model was combined with geographical information system (GIS) analysis to design a spatially explicit supply chain configuration. The GIS-based network analysis considered all of the counties in Georgia to set the candidate locations of carinata farms and facilities, and determined minimum cost and emission routes between those counties and the airport using existing transportation networks and modes (e.g. road, rail and pipeline). The MILP model determined the final selection of the farms and the number of facilities and their locations over those minimum-cost routes. With this supply chain configuration, the minimum price of SAF was $\$$0.92 L –1 , which is $\$$0.44 higher than conventional aviation fuel (CAF). The associated carbon intensity of SAF was estimated at 940.7 g CO 2 e L –1 , a reduction of 66% relative to the carbon intensity of equivalent CAF. The study found that a carbon tax (or subsidy) of $\$$230.48 t CO 2 e –1 would be needed to overcome the cost differential with CAF and promote carinata-based SAF in Georgia.

09 BIOMASS FUELS↗
DOE OSTI2021

Atomically dispersed single iron sites for promoting Pt and Pt 3 Co fuel cell catalysts: performance and durability improvements

Significantly reducing platinum group metal (PGM) loading while improving catalytic performance and durability is critical to accelerating proton-exchange membrane fuel cells (PEMFCs) for transportation. In this study, we report an effective strategy to boost PGM catalysts through integrating PGM-free atomically-dispersed single metal active sites in the carbon support toward the cathode oxygen reduction reaction (ORR). We achieved uniform and fine Pt nanoparticle (NP) (~2 nm) dispersion on an already highly ORR-active FeN 4 site-rich carbon (FeN 4 –C). Furthermore, we developed an effective approach to preparing a well-dispersed and highly ordered L1 2 Pt 3 Co intermetallic nanoparticle catalyst on the FeN 4 –C support. DFT calculations predicted a synergistic interaction between Pt clusters and surrounding FeN 4 sites through weakening O 2 adsorption by 0.15 eV on Pt sites and reducing activation energy to break O–O bonds, thereby enhancing the intrinsic activity of Pt. Experimentally, we verified the synergistic effect between Pt or Pt 3 Co NPs and FeN 4 sites, leading to significantly enhanced ORR activity and stability. Especially in a membrane electrode assembly (MEA) with a low cathode Pt loading (0.1 mg Pt cm –2 ), the Pt/FeN 4 –C catalyst achieved a mass activity of 0.451 A mg Pt –1 and retained 80% of the initial values after 30 000 voltage cycles (0.60 to 0.95 V), exceeding DOE 2020 targets. Furthermore, the Pt 3 Co/FeN 4 catalyst achieved significantly enhanced performance and durability concerning initial mass activity (0.72 A mg Pt –1 ), power density (824 mW cm –2 at 0.67 V), and stability (23 mV loss at 1.0 A cm –2 ). The approach to exploring the synergy between PGM and PGM-free Fe–N–C catalysts provides a new direction to design advanced catalysts for hydrogen fuel cells and various electrocatalysis processes.

25 ENERGY STORAGE↗