Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FIGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Characterization Techniques for LiInSe{sub 2} Semiconducting Neutron Detector - Paper 55

As the world supply of helium continues to dwindle, alternatives to neutron detection have been a key focus area of radiation detection research. Solid-state neutron detectors are one possible alternative to the {sup 3}He detectors currently used for neutron detection when large detector areas are not required. Although {sup 6}Li and {sup 10}B are both also commonly used for neutron detection, neither has as high of a thermal cross section as {sup 3}He. The thermal cross sections for {sup 6}Li, {sup 10}B, and {sup 3}He are, respectively, 940 barns, 3840 barns, and 5330 barns. Both boron and helium are used in a gaseous form for neutron detection; however, there is no suitable gaseous form of lithium for neutron detection. Lithium is instead utilized in solid or liquid compounds for neutron detection. In this context, one area of interest is in the development of ternary A{sup I}B{sup III}C{sup IV} semiconductors comprised of isotopically-enriched lithium. Single crystal samples are being prepared through collaboration with the Y12 National Security Complex. This research focuses on the characterization of {sup 6}LiInSe{sub 2} (LISe) crystals, as well as on the development of prototype systems to assess the viability of using LISe crystals as a thermal neutron detector. Data to be obtained will provide previously untested physical parameters to facilitate growth optimization. Eventually, the refined crystals will be developed into solid-state, position-sensitive pixel detectors used for neutron imaging, among a wide array of possible applications including nuclear forensics. For the most part, the research team has been focused on mastering the detector fabrication processes, response tests on the first two batches of crystal samples, and the design of the first iteration detection system (Fig. 2). Response tests using alphas and neutrons have shown sensitivity to both particles. The first iteration detection system developed utilizes a 3-stage filter ladder of resistors and capacitors, similar to an ORTEC 142PC Preamplifier. Ideally, this ladder will reduce the noise associated with the high voltage power supply. The preamplifier is AC coupled to improve its counting rate capability (saturation), and critical components are on insulated posts. The custom circuit is housed in an aluminum box, and initial testing of the circuit has shown expected results. Investigation into further noise reduction is underway and will be the focus of the presented results. Upon completion and successful testing of the final detection system design, further development in spatial resolution and gamma/neutron discrimination will continue. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Design of Nuclear Criticality Safety Framework for Hands-on Construction of Fast Systems Over Ranges of Multiplication

Since 1945, Los Alamos National Laboratory (LANL) has performed critical experiments, primarily at the Los Alamos Critical Experiments Facility (LACEF) at Technical Area 18 (TA-18). Since 2011, these experiments have been conducted by the National Criticality Experiments Research Center (NCERC), operated by LANL, at the Device Assembly Facility (DAF) in the Nevada National Security Site (NNSS). These experiments utilize various types of Special Nuclear Material (SNM). Some of these experiments utilize what is referred to as the Rocky Flat Shells, which are called such as they came from the Rocky Flats Plant. These concentric hemi-shells are made of Highly Enriched Uranium (HEU), which is 93 w/o 235U. Fig. 1. Subset of the Rocky Flat Shells LANL is designing a new subcritical hands-on experiment with the goal of achieving a neutron multiplication in the range of 50 to 200, which correlates to Keff values of 0.98 to 0.995. ANSI/ANS-1 is the standard for Conduct of Critical Experiments which governs critical operations at NCERC. Section 3.9 of ANSI/ANS-1 states that when manipulating a critical assembly by hand, the predicted k eff of a known configuration should not exceed 0.95 (a neutron multiplication of 20). This presents a challenge, as this system would have a higher multiplication than 20 and the assembly would have to remain subcritical in normal and credible accident scenarios. To ensure the safety of such an assembly, the different normal and abnormal conditions that could alter the criticality 1 MCNP® and Monte Carlo N-Particle® are registered trademarks owned by Triad National Security, LLC, manager and operator of Los Alamos National Laboratory. Any third party use of such registered marks should be properly of the system must be considered and analyzed. If such a condition is deemed to be credible, it will be further investigated using the Monte Carlo N-Particle (MCNP) transport code. If the results of these simulations show that a k eff larger than one could be possible, modifications to the assembly will be made until such an event is deemed no longer possible.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Zirconium Sludge Criticality Calculations in Large Process Tanks

The Savannah River Site’s (SRS) H-Canyon recently re-activated its 6.3D electrolytic dissolver to dissolve stainless steel clad research reactor fuels from Japan. A potential new mission was identified to dissolve other long-cooled fuel stored at SRS that is not aluminum clad. In the basic process of dissolution, the spent fuel dissolves into nitric acid (bulk solution). The eight ft. high and four ft. radius 6.3D dissolver is unique in that it has a platinum-coated niobium insert to resist corrosion, and the niobium basket forms an anode and cathode arrangement within the charge chute (Fig 1,2). DC current flows from anode to cathode, at up to 10,000 amps at 45 volts, through the potential gradient in the nitric acid solution, which allows the stainless steel (or other non-aluminum cladding) of the fuel to dissolve.

Wade, Brindley↗

The PARADIGM Project: Case Study in Balancing Experiment Uncertainty with Design simplicity

Accurate nuclear data are required for simulations of many applications including nuclear criticality safety. Actinide nuclear data at intermediate energies (from 1 to 100s of keV) are imprecise and inaccurate, because of scarce differential data, and an insufficient theory approach to capture the structures expected in the data to yield evaluated nuclear data, and lack of integral data for proper validation. This is a known deficiency but has proved challenging to address. More specifically, only 5% of integral experiments in the International Criticality Safety Benchmark Evaluation Project (ICSBEP) benchmark suite address intermediate energies (Fig. 1). Associated calculated effective multiplication factor, k eff , values for these experiments are far outside the experimental uncertainties and are 25× further from experiment than for fast energies. These differences could either stem from systematic biases in nuclear data, experiments or both. The goal of the PARADIGM (PARallel Approach of Differential and InteGral Measurements) project is to significantly reduce (by more than tens of percent) the uncertainties of intermediate energy actinide nuclear data. The PARADIGM project designed and intends to execute LANSCE (Los Alamos Neutron Science CEnter) and NCERC (National Criticality Experiments Research Center) intermediate experiments in parallel. They will specifically address a high priority nuclear data need—reducing bias and uncertainty in intermediate plutonium nuclear data. The two experiment will achieve that by informing each other and nuclear theory. By doing all these steps in parallel, the timeline to deliver improved nuclear data to users will significantly be reduced. This work will focus on the integral experiment final design and the balance of design and modeling simplicity while minimizing experiment uncertainty.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Assessment of Measurement Uncertainties in the Jupiter High-240 Experiment

The Jupiter High-240 experiment performed in May of 2019 was previously discussed as a variant of the original Jupiter experiment incorporating plutonium metal alloy fuel plates with higher 240Pu content and lead plates, using both a reference configuration and a second configuration where eight lead plates were replaced with aluminum to simulate voiding. Measurements were recorded for experiment period, the “pressure” of the Comet ram upon closure for each near-critical measurement, and temperature. The experiment reactor period is the time it would take to increase the neutron population by a factor of e. For this experiment, the copper reflectors and upper third of the fuel sits upon a support structure with the lower fuel arrays raised up into the center of the reflectors using a ram (see Fig. 1). The recorded logbook temperature for each measurement corresponds to a resistance temperature detector (RTD) located at the top center of the upper fuel array. This paper summarizes the evaluated uncertainties for the Jupiter High 240 experiment as contributed via the recorded measurements and nuclear data and their assessed impact upon the computation of system reactivity and eigenvalue.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Thermal Conductivity Measurements on Irradiated TRISO Fuel at IMCL

INL is leading the development and testing of accident tolerant fuels: fuels that resist melting down and that contain radioactive byproducts, preventing their release into their environment. One such fuel, called TRi-structural ISOtropic particle fuel (TRISO) See Fig 1. Understanding how heat propagates through a fuel is essential to fuel development and qualification. When irradiated in a reactor the properties that affect heat transport change. Our objective is to quantify the change in thermal properties of TRISO after irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ANS Winter 2024 Summary: Optimizing the ATF-2Ramp Power Profile

When the Halden Boiling Water Reactor closed down in 2018, a need to restore the capability for in-reactor power ramp testing arose. Such testing is valuable for studying pellet-clad interaction phenomena in nuclear fuels. The data from these studies is of great interest to a number of research programs, including the accident-tolerant fuel (ATF) program at Idaho National Laboratory (INL). In 2022, Woolstenhulme et al. proposed several power ramp testing ideas using facilities at INL, including irradiation in the Transient Reactor Test Facility (better known as TREAT) and the Advanced Test Reactor (ATR) [1]. Worrall et al. [2] and Labossiere-Hickman et al. [3] subsequently performed feasibility studies for the ATR testing options in 2023. This summary further investigates the three-pin trefoil design (Fig. 1) for the proposed ATF-2Ramp Experiment discussed in Labossiere-Hickman et al. [3]. ATF-2Ramp is designed to operate in the center flux trap (CFT) of the ATR during a powered axial locator mechanism (PALM) cycle: a short, variable-powered cycle with an asymmetric power distribution. Previously, it was shown that tailoring the thickness of the hafnium (Hf) neutron shields (“mini-shrouds”) surrounding each pin offered a degree of control sufficient to achieve the programmatic linear heat generation rate (LHGR) targets for ATF-2Ramp during the high-power period of a PALM cycle. New work involves shortening the experiment test train for consistency with the fuel pins in ATF-2D [4] and then shaping the axial power profile of the three test pins.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Field Testing of Safeguards Technologies in the Hot Fuel Examination Facility

Recent developments in nuclear fuel reprocessing techniques have yielded more efficient processes and fuel cycle options that strengthen the nuclear industry and production of clean energy. One such area of interest is pyroprocessing of used oxide fuel. However, with these advances in the back end of the nuclear fuel cycle, advances in safeguards instrumentation, measurements, and approaches are needed to ensure special nuclear material (SNM) is accounted for according to regulatory requirements. As a high-level overview of a nominal pyroprocessing approach, used oxide fuel from commercial light water reactors (LWR) is mechanically removed from the metallic cladding. Then the fuel is crushed and randomized representative samples are taken and sent to an analytical lab for analysis. The analytical results of the feed material are used for input accountancy into the rest of the process. The crushed oxide fuel is then moved to the oxide reduction (OR) furnace where it is reduced from an oxide to metallic form. The OR product is distilled to remove salt and then moved to an electrorefiner (ER), where it is immersed in a eutectic mixture of lithium chloride potassium chloride (LiCl-KCl) that typically ranges between 450-550 ?. Within the ER, the usable uranium is electrochemically transported through the molten salt from the anode to the cathode, and then subsequently removed as a relatively pure U product.. A simplified model of pyroprocessing techniques with added emphasis on the safeguards can be seen below in Fig. 1

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Wakefield and RF Kicks Due to Coupler Asymmetry in TESLA-Type Accelerating Cavities

In a future linear collider, such as the International Linear Collider (ILC), trains of high current, low emittance bunches will be accelerated in a linac before colliding at the interaction point. Asymmetries in the accelerating cavities of the linac will generate fields that will kick the beam transversely and degrade the beam emittance and thus the collider performance. In the main linac of the ILC, which is filled with TESLA-type superconducting cavities, it is the fundamental (FM) and higher mode (HM) couplers that are asymmetric and thus the source of such kicks. The kicks are of two types: one, due to (the asymmetry in) the fundamental RF fields and the other, due to transverse wakefields that are generated by the beam even when it is on axis. In this report we calculate the strength of these kicks and estimate their effect on the ILC beam. The TESLA cavity comprises nine cells, one HM coupler in the upstream end, and one (identical, though rotated) HM coupler and one FM coupler in the downstream end (for their shapes and location see Figs. 1, 2) [1]. The cavity is 1.1 m long, the iris radius 35 mm, and the coupler beam pipe radius 39 mm. Note that the couplers reach closer to the axis than the irises, down to a distance of 30 mm.

43 PARTICLE ACCELERATORS↗

Anisotropic Hexagonal Boron Nitride Nanomaterials - Synthesis and Applications

Boron nitride (BN) is a synthetic binary compound located between III and V group elements in the Periodic Table. However, its properties, in terms of polymorphism and mechanical characteristics, are rather close to those of carbon compared with other III-V compounds, such as gallium nitride. BN crystallizes into a layered or a tetrahedrally linked structure, like those of graphite and diamond, respectively, depending on the conditions of its preparation, especially the pressure applied. Such correspondence between BN and carbon readily can be understood from their isoelectronic structures [1, 2]. On the other hand, in contrast to graphite, layered BN is transparent and is an insulator. This material has attracted great interest because, similar to carbon, it exists in various polymorphic forms exhibiting very different properties; however, these forms do not correspond strictly to those of carbon. Crystallographically, BN is classified into four polymorphic forms: Hexagonal BN (h-BN) (Figure 1(b)); rhombohedral BN (r-BN); cubic BN (c-BN); and wurtzite BN (w-BN). BN does not occur in nature. In 1842, Balmain [3] obtained BN as a reaction product between molten boric oxide and potassium cyanide under atmospheric pressure. Thereafter, many methods for its synthesis were reported. h-BN and r-BN are formed under ambient pressure. c-BN is synthesized from h-BN under high pressure at high temperature while w-BN is prepared from h-BN under high pressure at room temperature [1]. Each BN layer consists of stacks of hexagonal plate-like units of boron and nitrogen atoms linked by SP{sup 2} hybridized orbits and held together mainly by Van der Waals force (Fig 1(b)). The hexagonal polymorph has two-layered repeating units: AA'AA'... that differ from those in graphite: ABAB... (Figure 1(a)). Within the layers of h-BN there is coincidence between the same phases of the hexagons, although the boron atoms and nitrogen atoms are alternatively located along the c-axis. The rhombohedral system consists of three-layered units: ABCABC..., whose honeycomb layers are arranged in a shifted phase, like as those of graphite. Reflecting its weak interlayer bond, the h-BN can be cleaved easily along its layers, and hence, is widely used as a lubricant material. The material is stable up to a high temperature of 2300 C before decomposition sets in [2] does not fuse a nitrogen atmosphere of 1 atm, and thus, is applicable as a refractory material. Besides having such properties, similar to those of graphite, the material is transparent, and acts as a good electric insulator, especially at high temperatures (10{sup 6} {Omega}m at 1000 C) [1]. c-BN and w-BN are tetrahedrally linked BN. The former has a cubic sphalerite-type structure, and the latter has a hexagonal wurtzite-type structure. c-BN is the second hardest known material (the hardest is diamond), the so-called white diamond. It is used mainly for grinding and cutting industrial ferrous materials because it does not react with molten iron, nickel, and related alloys at high temperatures whereas diamond does [1]. It displays the second highest thermal conductivity (6-9 W/cm.deg) after diamond. This chapter focuses principally upon information about h-BN nanomaterials, mainly BN nanotubes (BNNTs), porous BN, mono- and few-layer-BN sheets. There are good reviews book chapters about c-BN in [1, 4-6].

36 MATERIALS SCIENCE↗

14-MeV Neutron Generator Used as a Thermal Neutron Source

One of the most important applications of the general purpose Monte Carlo N-Particle (MCNPS and MCNPX) codes is neutron shielding design. We employed this method to simulate the shield of a 14-MeV neutron generator used as a thermal neutron source providing an external thermal neutron beam for testing large area neutron detectors developed for diffraction studies in biology and also useful for national security applications. Nuclear reactors have been the main sources of neutrons used for scientific applications. In the past decade, however, a large number of reactors have been shut down, and the importance of other, smaller devices capable of providing neutrons for research has increased. At Brookhaven National Laboratory a moderated Am-Be neutron source with shielding is used for neutron detector testing. This source is relatively weak, but provides a constant flux of neutrons, even when not in use. The use of a 14 MeV energized neutron generator, with an order of magnitude higher neutron flux has been considered to replace the Am-Be source, but the higher fast neutron yield requires a more careful design of moderator and shielding. In the present paper we describe a proposed shielding configuration based on Monte Carlo calculations, and provide calculated neutron flux and dose distributions. We simulated the neutron flux distribution of our existing Am-Be source surrounded by a paraffin thermalizer cylinder (radius of 17.8 cm), 0.8 mm cadmium, and borated polyethylene as biological shield. The thermal neutrons are available through a large opening through the polyethylene and cadmium. The geometrical model for the MCNPS and MCNPX2 simulations is shown in Fig. 1. We simulated the Am-Be source neutron energy distribution as a point source having an energy distribution of four discrete lines at 3.0 (37%), 5.0 (35%), 8.0 (20%) and 11.0 (8%) MeV energies. The estimated source strength based on the original specifications is 6.6 {center_dot} 10{sup 6} neutrons/sec. The simulation accurately predicts the measured thermal neutron flux at the collimator (Figure 2), thus providing validation for this method. Using MCNPX we simulated the neutron and photon dose distribution and also obtained a good agreement with the measured values. Having established a validated framework for the shield calculation we then scaled up the Am-Be arrangement to simulate the shielding required for the higher neutron energy and flux of the neutron generator (-10{sup 8} neutrodsec at 14 MeV). Given the physical dimensions of the generator we have chosen a cylindrical geometry, where the generator tube is placed vertically into a cylindrical thermalizer (25 cm paraffin) from above. The thermalizer is surrounded by 0.8 mm cadmium, and a cylindrical borated polyethylene shield. A cylindrical opening (radius of 7.6 cm) serves to direct the neutrons out towards the experimental area (on the right side). The initial model is shown in figure 3. The first goal of the calculations was to establish the minimal required radius of the biological shield. For this purpose we performed MCNPX neutron and photon dose distribution calculations by tallying the absorbed dose on a 200 x 200 cm mesh in the vertical center plane superimposed over the geometry. Figure 4. displays the neutron dose distribution along the central horizontal (X) axis. As observed from the figure, a shielding radius of -80 cm is sufficient to obtain a dose level of < -4 mrem/hour outside the shield (except from the open neutron channel on the right). In the next step we studied the optimization of the thickness of the paraffin thermalizer by increasing the depth of the neutron exit channel into the paraffin cylinder. It was found, that the thermal flux greatly increases if we have thinner paraffin layer, an optimal value being about 5 cm thickness. But as a drawback the flux of fast neutrons also increased. A thicker thermalizer layer, in fact, acts as shielding. A slightly off centered, tangential placement of the neutron channel provides a solution which maximizes the thermal flux to fast neutron yield. Figure 5. and 6. display the final results, where we included an outside biological shield (20 cm thickness) providing a shielded experimental area. There is a 10-100 n/cm{sup 2}sec flux near the neutron beam exit, and outside the shield the neutron dose is below the radiation area limit (-5 mrem/hour).

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

AFC-1 Fuel Rodlet Fission Power Deposition Validation in ATR

One of the viable options of long-term geological disposal of the nuclear power reactors generated spent fuel is to extract plutonium, the minor actinides (MA) and potentially long-lived fission products from the spent fuel and transmute them into short-lived or stable radionuclides in an appropriate reactor for the reduction of the radiological toxicity of the nuclear waste stream. An important component of that technology will be a non-fertile / low-fertile actinide transmutation fuel form containing the plutonium, neptunium, americium (and possibly curium) isotopes to be transmuted. Such advanced fuel forms, especially ones enriched in the long-life minor actinide (LLMA) elements (i.e., Np, Am, Cm), have minimal irradiation performance data available from which to establish a transmutation fuel form design. Recognizing these needs, an Advanced Fuel Cycle test series-1 (AFC-1) irradiation test on a variety of candidate fuel forms is now being conducted in Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). The first advanced fuel experiment (AFC-1) has been finalized and the test assembly analyzed for insertion and irradiation in ATR. The ATR core consists of a serpentine and rotationally symmetric fuel assembly about the z-axis of the core center. The plan view of the ATR core configuration is shown in Fig. 5, in Ref. 1. A cadmium filter with a 0.178 cm (0.045") thickness and 121.5 cm (48") in length, is currently used in the actinide-fuel capsule design for the East Flux Trap (EFT) position in ATR, to depress the linear heat generation rate (LHGR) lower than the project’s 330 W/cm limit for the experimental fuel rodlets. The LHGR is proportional to the fission power deposited in the fuel rodlets from the neutron fissions. The fraction of the fission power generated from the neutron fission reactions deposited in the fuel rodlet is an important parameter for test assembly thermal analysis, which will be validated in this summary.

99 GENERAL AND MISCELLANEOUS↗

Reply to Comment on "Ab Initio Study of 40Ca with an Importance Truncated No-Core Shell Model"

In their comment on our recent Letter [1] Dean et al. [2] criticize the calculations for the ground-state energy of {sup 40}Ca within the importance truncated no-core shell model (NCSM). In particular they address the role of configurations beyond the 3p3h level, which have not been included in the {sup 40}Ca calculations for large N{sub max} {h_bar}{Omega} model spaces. Before responding to this point, the following general statements are in order. For the atomic nucleus as a self-bound system, translational invariance is an important symmetry. The only possibility to preserve translational invariance when working with a Slater determinant basis is to use the harmonic oscillator (HO) basis in conjunction with a basis truncation according to the total HO excitation energy, i.e. N{sub max} {h_bar}{Omega}, as done in the ab initio NCSM. This is important not only for obtaining proper binding or excitation energies, but also for a correct extraction of physical wavefunctions. The spurious center-of-mass components can be exactly removed only if the HO basis and the N{sub max} {h_bar}{Omega} truncation are employed. The minimal violation of the translational invariance was one of the main motivations for developing the importance-truncation scheme introduced in the Letter. In this scheme, we start with the complete N{sub max} {h_bar}{Omega} HO basis space and select important configurations via perturbation theory. All symmetries are under control and our importance-truncated NCSM calculations are completely variational and provide an upper bound of the ground-state energy of the system. The restriction to the 3p3h level, made for computational reasons in the N{sub max} > 8 calculations for {sup 40}Ca, is not inherent to the importance truncation scheme. The explicit inclusion of 4p4h configurations--though computationally more demanding--is straight-forward, even for the largest N{sub max} {h_bar}{Omega} model spaces discussed. To demonstrate this fact we have performed full 4p4h calculations for {sup 40}Ca in a 14{h_bar}{Omega} no-core model space at {h_bar}{Omega} = 24 MeV using the V{sub low k} interaction employed in the Letter. The resulting ground state energy of E{sub 4p4h} = -471.0 MeV can be compared with E{sub 3p3h} = -461.2 MeV for the 3p3h calculation reported in Fig. 5(b) with an uncertainty of typically 1 MeV due to the extrapolation {kappa}{sub min} {yields} 0. Thus the 4p4h configurations change the resulting ground-state energy of {sup 40}Ca by approximately 2%. In addition to the explicit inclusion of 4p4h or higher-order configurations in the importance truncated space, there are various other means to account for their effect on the energy. We are presently developing a perturbative method for the inclusion of up to 6p6h configurations using the ground state obtained from the NCSM diagonalization as unperturbed state. Furthermore, there are even simpler methods, such as multireference Davidson corrections, which are employed successfully in quantum chemistry [3], for estimating the contribution of excluded configurations to the energy. They even restore size extensivity in an approximate way. The coupled-cluster method (CCM) used by the authors of the Comment lacks the above discussed features important for the nuclear many-body problem, in particular it violates translational invariance from the very beginning and it does not fulfill the variational principle. The problem of a spurious center-of-mass contamination of the many-body states in CCM is not resolved and often not even mentioned (see e.g. Ref. [4]). Moreover, non-iterative triples corrections like CCSD(T), as referred to in the comment, tend to overestimate the correlation energy or even collapse. It is claimed that the CCM is very accurate. A closer inspection of recently published nuclear many-body results does not support this statement. In Ref. [5], the {sup 4}He binding energy with the chiral N{sup 3}LO NN potential was determined with an uncertainty of several MeV. The same is obtained in the ab initio NCSM with accuracy of 10 keV [6, 7]. The CCM binding energy results for {sup 16}O with the identical chiral N{sup 3}LO NN potential obtained in Refs. [8] and [9] differ by more than 5 MeV. According to Ref. [9], the CD-Bonn NN potential overbinds {sup 16}O. This is contrary to results obtained in Ref. [10] and also contrary to expectations as the CD-Bonn underbinds lighter nuclei. The CCSD(T) ground state energy for {sup 40}Ca with V{sub low k} reported in Ref. [4] is about 30 MeV lower than our 4p4h-result (CCSD is about 20MeV lower). Taking into account the small 2% difference of our 3p3h and 4p4h results and the violation of the variational principle and the translational invariance in the CCM method, we believe that the CCM result overestimates the exact ground-state energy in this case.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Erratum: Extracting (n,(gamma)) direct capture cross sections from Coulomb dissociation: application to 14C(n,(gamma))15C

In Ref. [1] we proposed a systematic methodology to extract neutron capture cross sections from Coulomb Dissociation data. Using the Continuum Discretized Coupled Channel formalism to describe the {sup 15}C breakup process, the asymptotic normalization coefficient (ANC) for the ground state is extracted through a {chi}{sup 2} fit. The corresponding error bar is defined using {chi}{sub min}{sup 2} + 1. We discovered a mistake in the calculation of the errors associated with the extracted ANC and here we present the corrected values. The experimental data from which the ANC is extracted covers a range of energies up to 4 MeV, and the value obtained for the full energy range is C{sub 0} = 1.31 {+-} 0.07 fm{sup -1/2}. We find that the ANC is better determined if the high energy data is discarded and the maximum energy is cut at 1.2 MeV. This is justified since the direct measurements we are comparing to, and the peak of the cross section (Fig. 1 in Ref. [1]), all lie below this cut. The higher energy data is more uncertain and lies in a region where the theoretical cross section is insensitive to the ANC, thus adding unwarranted uncertainty to the extracted ANC. With this energy cut one can better determine the ANC as C{sub 0} = 1.32 {+-} 0.04 fm{sup -1/2}. All conclusions in our previous paper [1] hold. More details on the fitting procedure can be found in Ref. [2]. Figure 2 of Ref. [1] should be replaced by the figure below, where the shaded area is the range of uncertainty for an ANC of C{sub 0} = 1.32 {+-} 0.04 fm{sup -1/2}, extracted from data up to E = 1.2 MeV.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

X-RAY NONLINEAR OPTICAL PROCESSES IN ATOMS USING A SELF-AMPLIFIED SPONTANEOUS EMISSION FREE-ELECTRON LASER

X-ray free electron lasers (xFEL) will open new avenues to the virtually unexplored territory of non-linear interactions of x rays with matter. Initially xFELs will be based on the principle of self-amplified spontaneous emission (SASE). Each SASE pulse consists of a number of coherent intensity spikes of random amplitude, i.e. the process is chaotic and pulses are irreproducible. The coherence time of SASE xFELs will be a few femtoseconds for a photon energy near 1 keV. The importance of coherence properties of light in non-linear optical processes was theoretically discovered in the early 1960s. In this contribution we will illustrate the impact of field chaoticity on x-ray non-linear optical processes on neon for photon energies around 1 keV and intensities up to 10{sup 18} W/cm{sup 2}. Resonant and non-resonant processes are discussed. The first process to be addressed is the formation of a double-core hole in neon by photoionization with x rays above 1.25 keV energy. In contrast to the long-wavelength regime, non-linear optical processes in the x-ray regime are characterized in general by sequential single-photon single-electron interactions. Despite this fact, the sequential absorption of multiple x-ray photons depends on the statistical properties of the radiation field. Treating the x rays generated by a SASE FEL as fully chaotic, a quantum-mechanical analysis of inner-shell two-photon absorption is performed. By solving a system of time-dependent rate equations, we demonstrate that double-core hole formation in neon via x-ray two-photon absorption is enhanced by chaotic photon statistics. At an intensity of 10{sup 16} W/cm{sup 2}, the statistical enhancement is about 30%, much smaller than typical values in the optical regime. The second part of this presentation discusses the resonant Auger effect of atomic neon at the 1s-3p transition (at 867.1 eV). For low X-ray intensity, the excitation process 1s {yields} 3p in Neon can be treated perturbatively. The core-hole excited 1s{sup -1} 3p state is embedded in the continuum and decays via Auger-process on the timescale of approximately 5 fs. Increasing the x-ray intensity above 1.5 x 10{sup 18} W/cm{sup 2}, a peak intensity accessible with xFEL sources in the near future, x-ray induced emission from 3p back to 1s becomes possible, i.e. Rabi oscillations between these two levels can be induced. For the numerical analysis of this process, an effective two-level model, including a description of the resonant Auger decay process, is employed. The observation of x-ray-driven atomic populations dynamics in the time domain is challenging for chaotic xFEL pulses. In addition to requiring single-shot measurements, sub-femtosecond temporal resolution would be needed. The Rabi oscillations will, however, be imprinted on the kinetic energy distribution of the resonant Auger electron (see Fig. 1). Measuring the resonant Auger-electron line profile will provide information on both atomic population dynamics and x-ray pulse properties.

74 ATOMIC AND MOLECULAR PHYSICS↗

ON THE IMPACT OF SUPER RESOLUTION WSR-88D DOPPLER RADAR DATA ASSIMILATION ON HIGH RESOLUTION NUMERICAL MODEL FORECASTS

Assimilation of radar velocity and precipitation fields into high-resolution model simulations can improve precipitation forecasts with decreased 'spin-up' time and improve short-term simulation of boundary layer winds (Benjamin, 2004 & 2007; Xiao, 2008) which is critical to improving plume transport forecasts. Accurate description of wind and turbulence fields is essential to useful atmospheric transport and dispersion results, and any improvement in the accuracy of these fields will make consequence assessment more valuable during both routine operation as well as potential emergency situations. During 2008, the United States National Weather Service (NWS) radars implemented a significant upgrade which increased the real-time level II data resolution to 8 times their previous 'legacy' resolution, from 1 km range gate and 1.0 degree azimuthal resolution to 'super resolution' 250 m range gate and 0.5 degree azimuthal resolution (Fig 1). These radar observations provide reflectivity, velocity and returned power spectra measurements at a range of up to 300 km (460 km for reflectivity) at a frequency of 4-5 minutes and yield up to 13.5 million point observations per level in super-resolution mode. The migration of National Weather Service (NWS) WSR-88D radars to super resolution is expected to improve warning lead times by detecting small scale features sooner with increased reliability; however, current operational mesoscale model domains utilize grid spacing several times larger than the legacy data resolution, and therefore the added resolution of radar data is not fully exploited. The assimilation of super resolution reflectivity and velocity data into high resolution numerical weather model forecasts where grid spacing is comparable to the radar data resolution is investigated here to determine the impact of the improved data resolution on model predictions.

54 ENVIRONMENTAL SCIENCES↗

In Situ Laser Synthesis of Si Nanowires in the Dynamic TEM

Nanowires (NWs) are a crucial component in today's nanoscale devices and are vital to the further development of nanotechnology. To achieve reliable growth of NWs and uniform electronic properties, the specific mechanisms that control the structural development of NWs and the correlation between NWs and their nucleation and growth processes must be examined. Because imaging is not possible in Chemical Vapor Deposition (CVD) chambers, in situ transmission electron microscope (TEM) based growth methods provide a method for characterizing NW evolution. In this paper, we describe a new method of in situ synthesis and imaging of NWs using laser-assisted growth inside a TEM. The vapor-liquid solid (VLS) growth mechanism (Figure 1), first described by Wagner and co-workers, is a widely accepted description of how many 1D nanostructures are formed. VLS and similar models have been applied to such methods as hybrid pulsed-laser ablation/chemical vapor deposition (PLA/CVD) and laser assisted NW growth at elevated temperatures, in which a pulsed laser ablates a target with gas flowing through the reaction chamber held at elevated temperature. These methods have successfully produced semiconductor and conducting oxide NWs with size control determined by the catalyst droplet diameter. The VLS description of NW growth is a widely accepted model, but the exact role of vapor species and its interaction with the catalyst particle is not fully understood. For example, NW growth has been observed to occur far below predicted eutectic temperatures, which suggests that alternative mechanisms such as solid-liquid-solid growth (SLS) may play a role. Many NW fabrication techniques preclude direct in situ characterization of the growth process. Because of this need for direct observation during growth, TEM-based NW growth methods have become increasingly popular. Though progress has been made in the study of the VLS mechanism of NW growth using in situ TEM, conventional in situ growth experiments are limited by the standard video frame rate ({approx}30 Hz). Because of this limitation, relationships between reactant incorporation and transport, catalyst-wire interface development, and wire growth texture remain somewhat unclear. Moreover, laser-assisted phenomena (PLA or PLA/CVD) cannot be studied with conventional in situ TEM, which is typically performed with environmental TEM techniques using resistive heating. A novel form of in situ TEM for the study of NW growth by laser-assisted techniques is described in this paper. Here we present an in situ method for PLA synthesis of 1D nanostructures using the dynamic transmission electron microscope (DTEM)[18,19] that will permit the details of laser-assisted NW synthesis to be elucidated. The DTEM, schematically shown in Figure 2, consists of a TEM column (JEOL 2000FX) to which a pulsed Nd:YAG laser, labeled 'hydrodrive laser' in Fig. 2, is added. This laser is incident directly on the sample and can be operated at 1064, 532 or 355nm. The direct delivery of energy initiates a phase change or reaction that is investigated in situ during the experiment. Thus, the microscope can be used to fabricate NWs while simultaneously characterizing the reaction products created by each laser pulse. A second pulsed laser (15-ns-duration frequency-quintupled Nd:YLF) added to the column (labeled 'cathode laser' in figure 2) enables operation in both a pulsed photoemission and conventional thermionic continuous-wave (CW) electron beam imaging modes.[19] The pulsed mode's nanosecond-scale imaging capability greatly exceeds the {approx}30 Hz time resolution of conventional in situ TEM and can potentially provide a detailed understanding of NW growth. Time-resolved imaging experiments aimed at capturing the intermediate states at nanosecond time scales in PLA NW growth are underway and will be addressed in a future publication. In this paper, we present results obtained using in situ imaging in conventional CW imaging mode, but taking advantage of the DTEM's in situ laser drive capability. Specifically, we will present the first results using the sample ('hydro-drive') laser at 355nm to stimulate the growth of the nanostructures, therefore revealing the DTEM as a tool for in situ imaging of nanostructure synthesis (see the experimental section for details of the NW synthesis procedure).

36 MATERIALS SCIENCE↗

Erratum: Coherent Anti-Stokes Raman Spectroscopy of Highly Compressed Solid Deuterium at 300K: Evidence for a New Phase and Implication for the Band Gap

In our original Letter, we were inconsistent in our application of the deuterium equation of state (EOS). In this Erratum we recalculated the EOS to the parameters from Hemley et al. [Phys. Rev. B 42, 6458 (1990)]. The consequence of this change is minimal. The scale of the difference is smaller, but the evidence for phase I' remains. The corrected Fig. 3 graphs are provided.

08 HYDROGEN↗