Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Experimental Methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Phase-Sensitive Optical Time Domain Reflectometry With Rayleigh Enhanced Optical Fiber

In this paper, a phase-sensitive optical time domain reflectometry (Φ-OTDR) based on Rayleigh enhanced optical fiber is proposed to improve the system signal-to-noise ratio (SNR). In the experiment, the vibration performance of the Rayleigh enhanced optical fiber is analyzed and compared with standard single-mode telecom fiber. The results demonstrate that the measured SNRs of peaks in frequency spectra have been improved by 14 dB (at 1 kHz vibration frequency) at the end of the 2 km specialty sensing fiber. A wide range of vibration frequencies from 50 Hz to 15 kHz are demonstrated experimentally. The proposed method overcomes the inherent limitations of the conventional Φ-OTDR system and significantly enhances the vibration sensing performance.

47 OTHER INSTRUMENTATION↗

Flexible PCB Windings Size Optimization for Winding AC Resistance Minimization Under the Sinusoidal Voltage Regime

In this paper, optimization of the winding AC resistance of the flexible printed circuit board (FPCB) wire windings is performed. A one-dimensional model of the FPCB winding is introduced and an equation for the FPCB winding AC resistance and its low and medium frequency approximation are derived. The approximate FPCB winding AC resistance equation is used to derive optimum thickness of the FPCB winding conductor thickness at which minimum of winding AC resistance (global optimum) is achieved. The Finite Element Method analysis and experimental verification of derived equations (winding resistance, impedance, power loss, and temperature measurements) is performed in order validate derived model and winding resistance equation.

42 ENGINEERING↗

Decentralized Interleaving of Cascaded H-Bridge Multi-Level Converters

This document proposes a simple method to decentralize the interleaving for cascaded H bridge (CHB) converters. In the proposed approach, a single signal sent from the Central controller (CC) to Local Controllers (LC) contains information about the desired pulse width and is synchronized with respect to other LC. While centralized controllers need individual signals for each of the CHB modules, the proposed method requires a single signal per phase which decreases the number of PWM channels needed. A detailed explanation of the proposed method is presented. Experimental results are presented that show the interleaving of two CHB modules for an example DC to AC application.

Montes, Oscar Andres↗

Self-Secure Inverters Against Malicious Setpoints

The next generation of grid-interactive inverters brings a communication feature that allows data sharing from utility supervisory controllers and smart devices that are connected to the same network. This feature enhances the control capabilities of grid-interactive inverters to provide services beyond active power injection. However, communication networks entail more vulnerable surfaces to malicious attacks that may result in modifying active and reactive power setpoints and causing weak-grid conditions or abnormal inverter operation. In this paper, steady-state and the dynamic behavior of the inverter for the incoming setpoints are analyzed to detect false data injection attacks and provide device-level security. The steady-state behavior of the inverter in the operating region is determined from the grid parameters such as the grid voltage and the grid impedance. These estimations are accomplished by the proposed self-security technique through a low-frequency signal injection-based approach combined with the recursive least square method. Moreover, a reduced fourth-order inverter model is used as the dynamic reference model, and grid parameters as well as the incoming setpoints are implemented to the reference model to verify whether the dynamic behavior of the inverter is inside the permissible region of operation. The validity and performance of the proposed method are verified experimentally through Allen-Bradley Powerflex 755 three-phase inverter and a 12 kW NHR 9410 regenerative power grid emulator. The results show that the self-secure smart-inverter is able to accept or reject the incoming commands and thus is protected from malicious cyber-physical attacks.

Hossen, Tareq↗

SociAL Sensor Analytics: Measuring Phenomenology at Scale

The objective of this paper is to present a system for interrogating immense social media streams through analytical methodologies that characterize topics and events critical to tactical and strategic planning. First, we propose a conceptual framework for interpreting social media as a sensor network. Time-series models and topic clustering algorithms are used to implement this concept into a functioning analytical system. Next, we address two scientific challenges: 1) to understand, quantify, and baseline phenomenology of social media at scale, and 2) to develop analytical methodologies to detect and investigate events of interest. This paper then documents computational methods and reports experimental findings that address these challenges. Ultimately, the ability to process billions of social media posts per week over a period of years enables the identification of patterns and predictors of tactical and strategic concerns at an unprecedented rate through SociAL Sensor Analytics (SALSA).

analytics↗

Investigation of Various Transformer Topologies for HF Isolation Applications

High-frequency (HF) transformers are an essential part of many power electronic devices. The performance and behavior of HF transformers can greatly affect the efficiency and performance of all systems, particularly, from a parasitic parameter point of view. In this article, HF transformers' parasitic parameters, such as leakage inductances and parasitic capacitances, are analyzed using a novel analytical method, finite element method (FEM), and experimental measurements of different structures and winding arrangements. Also, the magnetic field, electric field, electric displacement field, and electric potential distribution within the transformers are simulated and analyzed. Four different HF transformers with E and U cores with different windings are designed and analyzed. Investigation outcomes help to classify structures according to the trade-off between leakage inductances and series parasitic capacitances. This information can later be used for the optimal selection and design of transformers as a function of their operating frequency for any power rating and voltage level. Moreover, 3-D FEM and experimental results validate the proposed methodology to be used for designing HF transformers in high-voltage/power applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Factors governing extracellular DNA degradation dynamics in soil

We examined the impacts of soil moisture, temperature, agricultural management and habitat type on the degradation dynamics of eDNA in soils. Synthetic eDNA was added to soil microcosms, and its disappearance over time was measured using both high-throughput sequencing and qPCR. The synthetic eDNA was degraded rapidly, but a small fraction remained detectable throughout the experiments (39–80 days). The eDNA degradation rate was positively correlated with moisture and temperature, but negatively correlated with soil organic carbon content. End-point stabilization of eDNA was highest at low moisture and temperature, but exhibited no relationship with soil organic carbon. Tilled soils had higher rates of degradation and less stabilization than no-till soils. Among different habitats we observed that forest soils had the slowest degradation rate, and meadow soils had the greatest stabilization of eDNA. While eDNA was detectable by qPCR in all treatments across all time-points, it became inconsistently detectable with high-throughput gene sequencing in less than 1 week. We conclude that eDNA degradation and stabilization dynamics vary with moisture, temperature and habitat characteristics, that small amounts of eDNA may persist in soils indefinitely, and that the ability of persistent eDNA to impact microbial community estimates depends on method sensitivity and experimental objectives.

59 BASIC BIOLOGICAL SCIENCES↗

Uncertainty Propagation Analysis of Computational Models in Laser Powder Bed Fusion Additive Manufacturing Using Polynomial Chaos Expansions

Computational models for simulating physical phenomena during laser-based powder bed fusion additive manufacturing (L-PBF AM) processes are critical for enhancing our understanding of these phenomena, enable process optimization, and accelerate qualification and certification of AM materials and parts. It is a well-known fact that such models typically involve multiple sources of uncertainty that originate from different sources such as model parameters uncertainty, or model/code inadequacy, among many others. Uncertainty quantification (UQ) is a broad field that focuses on characterizing such uncertainties in order to maximize the benefit of these models. Although UQ has been a center theme in computational models associated with diverse fields such as computational fluid dynamics and macro-economics, it has not yet been fully exploited with computational models for advanced manufacturing. The current study introduces one among the first efforts to conduct uncertainty propagation (UP) analysis in the context of L-PBF AM. More specifically, we present a generalized polynomial chaos expansions (gPCE) framework to assess the distributions of melt pool dimensions due to uncertainty in input model parameters. We develop the methodology and then employ it to validate model predictions, both through benchmarking them against Monte Carlo (MC) methods and against experimental data acquired from an experimental testbed.

36 MATERIALS SCIENCE↗

STRUCTURAL MODELING TO SUPPORT POST-YIELD ACCEPTANCE CRITERIA FOR SPENT NUCLEAR FUEL CLADDING

Spent nuclear fuel (SNF) is evaluated for structural failure during storage and transportation scenarios. The U.S. Department of Energy’s Spent Fuel and Waste Science and Technology (SFWST) program has sponsored significant research in quantifying mechanical loads on SNF during storage and transportation scenarios using experimental and modeling methods. The SFWST program has also performed significant research on measuring the mechanical behavior of irradiated SNF as defueled cladding segments and cladding with fuel pellets to measure composite behavior. This paper considers some of the key material data from the Sibling Pin testing and uses structural modeling and analysis methods that have been informed by testing to consider post-yield acceptance criteria for SNF cladding structural analysis. Test data published by Oak Ridge National Laboratory (ORNL) and Pacific Northwest National Laboratory (PNNL) are the foundation for informing the material behavior of the models developed in this study. In particular, four-point bend (4PB) tests of fueled and defueled cladding segments provide significant information about the bending failure mode of SNF. ORNL’s 4PB test data is on fueled cladding segments, so the composite behavior of SNF is demonstrated. This paper describes PNNL’s coincident beam model that was developed to approximate the composite behavior of SNF. This paper also presents PNNL’s structural dynamic finite element models of a cask tip-over scenario, which is predicted to cause the strongest mechanical loads on SNF of all postulated storage and transportation scenarios. SNF bending loads predicted in the cask tip-over scenario and cladding acceptance criteria beyond yield are considered, with justification based on the Sibling Pin test data. ASME Boiler and Pressure Vessel code stress intensity limits are also considered. The ultimate goal of this work is to aid in the justification of structural acceptance criteria for SNF cladding beyond the cladding’s irradiated yield strength for use in structural analysis of all storage and transportation scenarios.

Klymyshyn, Nicholas A.↗

Etching characteristics and mechanisms of SiC thin films in inductively-coupled HBr-Ar, N{sub 2}, O{sub 2} plasmas

Etch characteristics and mechanisms of SiC thin films in HBr-Ar, HBr-N{sub 2}, and HBr-O{sub 2} inductively-coupled plasmas were studied using a combination of experimental and modeling methods. The etch rates of SiC thin films were measured as functions of the additive gas fraction in the range of 0-100% for Ar, N{sub 2}, and O{sub 2} at a fixed gas pressure (6 mTorr), input power (700 W), bias power (200 W), and total gas flow rate (40 sccm). The plasma chemistry was analyzed using Langmuir probe diagnostics and a global (zero-dimensional) plasma model. The good agreement between the behaviors of the SiC etch rate and the H atom flux could suggest that a chemical etch pathway is rather controlled by the gasification of carbon through the CH{sub x} or CH{sub x}Br{sub y} compounds.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Dehydration of Uranyl Nitrate Hexahydrate to Uranyl Nitrate Trihydrate under Ambient Conditions as Observed via Dynamic Infrared Reflectance Spectroscopy

the hexahydrate [UO 2 (NO 3 ) 2 (H 2 O) 6 ] (UNH) and the trihydrate [UO 2 (NO 3 ) 2 (H 2 O) 3 ] (UNT) forms. Their stabilities depend on both relative humidity and temperature. Both phases have previously been studied by infrared transmission spectroscopy, but the data were limited by both instrumental resolution and the ability to prepare the samples as pellets without desiccating them. We report time-resolved infrared (IR) measurements using an integrating sphere that allow us to observe the transformation from the hexahydrate to the trihydrate simply by flowing dry nitrogen gas over the sample. Hexahydrate samples were prepared and confirmed via known XRD patterns, then measured in reflectance mode. The hexahydrate has a distinct uranyl asymmetric stretch band at 949.0 cm -1 that shifts to shorter wavelengths and broadens as the sample dehydrates and recrystallizes to the trihydrate, first as a blue edge shoulder but ultimately resulting in a doublet band with reflectance peaks at 966 and 957 cm -1 . The data are consistent with transformation from UNH to UNT since UNT has two non-equivalent UO 2 2+ sites. The dehydration of UO 2 (NO 3 ) 2 (H 2 O) 6 to UO 2 (NO 3 ) 2 (H 2 O) 3 is both a morphological and structural change that has the lustrous lime green crystals changing to the dull greenish yellow of the trihydrate. Crystal structures and phase transformation were confirmed theoretically using DFT calculations and experimentally via microscopy methods. Both methods showed a transformation with two distinct sites for the uranyl cation in the trihydrate, as opposed to a single crystallographic site in the hexahydrate.

36 MATERIALS SCIENCE↗

SU-E-J-219: Quantitative Evaluation of Motion Effects On Accuracy of Image-Guided Radiotherapy with Fiducial Markers Using CT Imaging

Purpose: To investigate quantitatively patient motion effects on the localization accuracy of image-guided radiation with fiducial markers using axial CT (ACT), helical CT (HCT) and cone-beam CT (CBCT) using modeling and experimental phantom studies. Methods: Markers with different lengths (2.5 mm, 5 mm, 10 mm, and 20 mm) were inserted in a mobile thorax phantom which was imaged using ACT, HCT and CBCT. The phantom moved with sinusoidal motion with amplitudes ranging 0–20 mm and a frequency of 15 cycles-per-minute. Three parameters that include: apparent marker lengths, center position and distance between the centers of the markers were measured in the different CT images of the mobile phantom. A motion mathematical model was derived to predict the variations in the previous three parameters and their dependence on the motion in the different imaging modalities. Results: In CBCT, the measured marker lengths increased linearly with increase in motion amplitude. For example, the apparent length of the 10 mm marker was about 20 mm when phantom moved with amplitude of 5 mm. Although the markers have elongated, the center position and the distance between markers remained at the same position for different motion amplitudes in CBCT. These parameters were not affected by motion frequency and phase in CBCT. In HCT and ACT, the measured marker length, center and distance between markers varied irregularly with motion parameters. The apparent lengths of the markers varied with inverse of the phantom velocity which depends on motion frequency and phase. Similarly the center position and distance between markers varied inversely with phantom speed. Conclusion: Motion may lead to variations in maker length, center position and distance between markers using CT imaging. These effects should be considered in patient setup using image-guided radiation therapy based on fiducial markers matching using 2D-radiographs or volumetric CT imaging.

60 APPLIED LIFE SCIENCES↗

SU-E-J-200: Operation of An Electron Accelerator On An Integrated MR-Linac System

Purpose: An integrated MRI guided radiotherapy system poses a challenge of operating a linear accelerator in the presence of a magnetic field as the magnetic force acting on the electrons could Result in radiation source displacement and subsequent reduction of dose output. It was the purpose of this work to test the performance of a linac in the presence of a 1.5T MRI system. Methods: The first experimental MRI guided radiotherapy system at UMC-Utrecht consisting of an Elekta linac rotating around a 1.5T Magnex magnet was examined. A passive magnetic shield was simulated, designed and installed to reduce the influence of the MRI magnet stray field on the electron beamline. The B field inside the shield was measured as a function of gantry angle and measurements of dose rate constancy upon gantry rotation were performed. Results: The magnitude of the magnetic field on the electron beam path without the shield was as high as 70G. It varied by up to 15G with gantry rotation due to the presence of metal beams in the bunker floor which resulted in dose output drop of up to 70% at certain gantry angles. With the prototype shield, field magnitude was reduced to well below 0.5G everywhere along the electron beam path. Field variation with gantry rotation was decreased to below 0.2G and enabled dose output of the linac to be recovered at all gantry angles. The homogeneity of the field inside the MRI magnet has not been compromised. Conclusion: It was demonstrated that the influence of the 1.5T magnet and the bunker design on the linac operation has been minimised. The performance will be further improved on the Elekta Atlantic system which incorporates a newly developed and optimised Philips magnet design and bunker construction. J Harasimowicz, D Roberts, I Shinton and S Sund are employed by Elekta Limited Crawley, H Wang and M Zhong are employed by Elekta Beijing Medical Systems Co. Ltd., J Overweg is employed by Philips Technologie GmbH Forschungslaboratorien.

60 APPLIED LIFE SCIENCES↗

TU-AB-303-08: GPU-Based Software Platform for Efficient Image-Guided Adaptive Radiation Therapy

Purpose: In this study, we develop an integrated software platform for adaptive radiation therapy (ART) that combines fast and accurate image registration, segmentation, and dose computation/accumulation methods. Methods: The proposed system consists of three key components; 1) deformable image registration (DIR), 2) automatic segmentation, and 3) dose computation/accumulation. The computationally intensive modules including DIR and dose computation have been implemented on a graphics processing unit (GPU). All required patient-specific data including the planning CT (pCT) with contours, daily cone-beam CTs, and treatment plan are automatically queried and retrieved from their own databases. To improve the accuracy of DIR between pCT and CBCTs, we use the double force demons DIR algorithm in combination with iterative CBCT intensity correction by local intensity histogram matching. Segmentation of daily CBCT is then obtained by propagating contours from the pCT. Daily dose delivered to the patient is computed on the registered pCT by a GPU-accelerated superposition/convolution algorithm. Finally, computed daily doses are accumulated to show the total delivered dose to date. Results: Since the accuracy of DIR critically affects the quality of the other processes, we first evaluated our DIR method on eight head-and-neck cancer cases and compared its performance. Normalized mutual-information (NMI) and normalized cross-correlation (NCC) computed as similarity measures, and our method produced overall NMI of 0.663 and NCC of 0.987, outperforming conventional methods by 3.8% and 1.9%, respectively. Experimental results show that our registration method is more consistent and roust than existing algorithms, and also computationally efficient. Computation time at each fraction took around one minute (30–50 seconds for registration and 15–25 seconds for dose computation). Conclusion: We developed an integrated GPU-accelerated software platform that enables accurate and efficient DIR, auto-segmentation, and dose computation, thus supporting an efficient ART workflow. This work was supported by NIH/NCI under grant R42CA137886.

60 APPLIED LIFE SCIENCES↗

Steam-created grain boundaries for methane C–H activation in palladium catalysts

Defects may display high reactivity because the specific arrangement of atoms differs from crystalline surfaces. We demonstrate that high-temperature steam pretreatment of palladium catalysts provides a 12-fold increase in the mass-specific reaction rate for carbon-hydrogen (C–H) activation in methane oxidation compared with conventional pretreatments. Through a combination of experimental and theoretical methods, we demonstrate that an increase in the grain boundary density through crystal twinning is achieved during the steam pretreatment and oxidation and is responsible for the increased reactivity. The grain boundaries are highly stable during reaction and show specific rates at least two orders of magnitude higher than other sites on the palladium on alumina (Pd/Al 2 O 3 ) catalysts. Theoretical calculations show that strain introduced by the defective structure can enhance C–H bond activation. Introduction of grain boundaries through laser ablation led to further rate increases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Methods and Models for Analyzing Methane Sorption Capacity of Coal Based on Its Physicochemical Characteristics

The authors study the influence of physicochemical parameters on methane adsorption capacity of coal and offer the analytical method for the methane adsorption capacity for three-phased condition of methane. It is found that in the depth interval to 300 m below surface, methane adsorption capacity measured in lab can exceed natural gas content of coal obtained from geological exploration data by 30%, and the change in the thermodynamic condition of coal–methane system brings irreversible physicochemical consequences in terms of the altered ratios of physical states of the main components. There is no linear connection between natural gas content of a coal bed and its methane adsorption capacity with respect to occurrence depth. The application of Big Data in treatment and interpretation of large data flows is described. The theoretical data predicted using the proposed method and the experimental data on methane content of Kuzbass coal agree.

01 COAL, LIGNITE, AND PEAT↗

X-ray phase-contrast methods

This review is devoted to a comparative description of the methods for forming X-ray phase-contrast images of weakly absorbing (phase) objects. These include the crystal interferometer method, the Talbot interferometer method, diffraction-enhanced X-ray imaging, and the in-line method. The potential of their practical application in various fields of science and technology is discussed. The publications on the development and optimization of X-ray phase-contrast methods and the experimental study of phase objects are analyzed.

36 MATERIALS SCIENCE↗

On a Technique of Studying the Interface Kinetics and Anisotropy of Specific Interfacial Energy Based on Experiments on Migration of Liquid Cylindrical Inclusions in a Crystal under Stationary Thermal Conditions

A method for processing experimental data on the migration of liquid cylindrical inclusions in a crystal under a temperature gradient has been considered on the assumption that the experimental thermal conditions are stationary. Formulas are derived to calculate the degree of interfacial energy anisotropy and relative hindrance of the crystallization and dissolution processes at atomically smooth interface areas based on the shapes of cross sections of cylindrical inclusions migrated perpendicular to the close-packed crystal planes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗