Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engine”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

High-Voltage LED Light Engine with Integrated Driver

LED luminaires have seen dramatic changes in cost breakdown over the past few years. The LED component cost, which until recently was the dominant portion of luminaire cost, has fallen to a level of the same order as the other luminaire components, such as the driver, housing, optics etc. With the current state of the technology, further luminaire performance improvement and cost reduction is realized most effectively by optimization of the whole system, rather than a single component. This project focuses on improving the integration between LEDs and drivers. Lumileds has developed a light engine platform based on low-cost high-power LEDs and driver topologies optimized for integration with these LEDs on a single substrate. The integration of driver and LEDs enables an estimated luminaire cost reduction of about 25% for targeted applications, mostly due to significant reductions in driver and housing cost. The high-power LEDs are based on Lumileds’ patterned sapphire substrate flip-chip (PSS-FC) technology, affording reduced die fabrication and packaging cost compared to existing technology. Two general versions of PSS-FC die were developed in order to create the desired voltage and flux increments for driver integration: (i) small single-junction die (0.5 mm 2 ), optimal for distributed lighting applications, and (ii) larger multi-junction die (2 mm 2 and 4 mm 2 ) for high-power directional applications. Two driver topologies were developed: a tapped linear driver topology and a single-stage switch-mode topology, taking advantage of the flexible voltage configurations of the new PSS-FC die and the simplification opportunities enabled by integration of LEDs and driver on the same board. A prototype light engine was developed for an outdoor “core module” application based on the multi-junction PSS-FC die and the single-stage switch-mode driver. The light engine meets the project efficacy target of 128 lm/W at a luminous flux greater than 4100 lm, a correlated color temperature (CCT) of 4000K and a color rendering index (CRI) greater than 70.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Simulation of Internal Combustion Engines with High-Performance Computing Tools

Traditional Lagrangian spray modeling approaches for internal combustion engines are highly griddependent due to insufficient resolution in the near nozzle region. This is primarily because of inherent restrictions of volume fraction with the Lagrangian assumption together with high computational costs associated with small grid sizes. A state-of-the-art grid-convergent spray modeling approach was developed and implemented by Senecal et al. (ASME-ICEF2012-92043) in the CONVERGE software. The key features of the methodology include Adaptive Mesh Refinement (AMR), advanced liquid-gas momentum coupling, and improved distribution of the liquid phase, which enables use of cell sizes smaller than the nozzle diameter. This modeling approach was rigorously validated against nonevaporating, evaporating, and reacting data from the literature. The current numerical study focusses on further demonstration of the grid-convergent modeling approach for simulating a single-cylinder Cat® compression ignition engine. The simulated injector is characterized with a nominal nozzle exit diameter of 259 μm. Simulations using various minimum grid sizes (ranging from 125 μm to 1000 μm) are compared for engine performance and emissions parameters of interest such as pressure, heat release rate, ignition delay, NOx, HC, and soot emissions. The peak cell-count for the highest resolution simulation was on the order of 34 million. These computationally expensive simulations were facilitated at a high-performance computing facility at Argonne National Laboratory. METIS load-balancing algorithm was developed and implemented in Converge code for the simulations. Scaling studies were also performed. The validity of previously recommended grid settings (ASME-ICEF2012-92043) for accuracy/runtime trade-off is further assessed. Efficacy of a simplified combustion model is also compared against a detailed chemical kinetics based combustion model.

33 ADVANCED PROPULSION SYSTEMS↗

Compatibility of Anti-Wear Additives with Non-Ferrous Engine Bearing Alloys

Investigate the compatibility of engine lubricant antiwear (AW) additives, specifically conventional zinc dialkyldithiophosphate (ZDDP) and newly developed ionic liquids (ILs), with selected non-ferrous engine bearing alloys, specifically aluminum and bronze alloys that are commonly used in connecting rod end journal bearings and bushings, to gain fundamental understanding to guide future development of engine lubricants

36 MATERIALS SCIENCE↗

A Continuing Education Short Course and Engineering Curriculum to Accelerate Workforce Development in Wind Power Plant Design, Construction, and Operations

Significant advances in wind turbine technology and wind turbine power plant capabilities are appearing in the U.S. Sites that only 10 years ago might have been overlooked are being considered for build out. However, the development of a skilled workforce in the engineering fields and construction trades lags the potential market, especially if the industry is expected to site, design, construct, and operate sufficient wind power plant sites to meet the potential for 20% wind energy by 2030. A select few firms have penetrated the engineer-procure-construction (EPC) market of wind power plant construction. Competition and know-how in this market is vital to achieve cost-effective, design-construct solutions. The industry must produce or retrain engineers, contractors, and technicians to meet ambitious goals. Currently, few universities offer undergraduate or graduate classes that teach the basics in designing, building, and maintaining wind power plants that are safe, efficient, and productive.

17 WIND ENERGY↗

Development of Advanced High Strength Cast Alloys for Heavy Duty Engines

Gray iron has been the primary alloy for heavy duty diesel engine core castings for decades. During recent decades the limitations of gray iron have been reached in some applications, leading to the use of compacted graphite iron in engine blocks and heads. Caterpillar has had compacted graphite designs in continuous production since the late 1980’s. Due to the drive for higher power density, decreased emissions and increased fuel economy, cylinder pressures and temperatures continue to increase. Currently no viable replacement for today’s compacted graphite irons exist at an acceptable cost level. This project explored methods to develop the next generation of heavy duty diesel engine materials as well as demonstrated some results on new alloy designs although cost targets will likely not be met.

36 MATERIALS SCIENCE↗

Multifamily Tool for Energy Audits (MulTEA) Engineering Manual (Version 1)

The Multifamily Tool for Energy Audits (MulTEA) is an energy audit tool designed to provide auditors with an improved energy simulation tool for multifamily buildings and an improved tool for identifying cost-effective energy-efficiency retrofit measures for multifamily buildings. MulTEA is designed specifically to help states and local weatherization agencies implement the Department of Energy (DOE) Weatherization Assistance Program. MulTEA was developed jointly by the Oak Ridge National Laboratory (ORNL) and the Lawrence Berkeley National Laboratory (LBNL). MulTEA is part of ORNL’s web-based Weatherization Assistant suite of audit tools (https://weatherization.ornl.gov/softwaredescription/). The energy calculation engine including the DOE- 2 simulation model and supplementary calculation modules is shared by MulTEA and LBNL’s Home Energy Saver pro (HESpro) (http://hespro.lbl.gov/pro/). On the ORNL side, the energy calculation engine is coupled with a user interface and output reporting capabilities based on Weatherization Assistance Program regulations and guidelines pertinent to MulTEA. On the LBNL side, the same engine will be used in HESpro to expand it to handle multifamily buildings. MulTEA is designed to address small and large multifamily buildings with decentralized and centralized heating, ventilation, and air-conditioning (HVAC) and domestic hot water (DHW) systems. Version 1 of MulTEA addresses small multifamily buildings with decentralized HVAC systems, and decentralized or centralized DHW systems. The capability to model large buildings and centralized HVAC systems will be incorporated in Version 2.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Global Survey of Selected Deep Underground Facilities; Examples of Geotechnical and Engineering Capabilities, Achievements, Challenges(Mines, Shafts, Tunnels, Boreholes, Sites and Underground Facilities for Nuclear Waste and Physics R&D):A Guide

This report presents tables, references, notes, and a synthesis of some notable geotechnical and engineering information that were applied in the creation of five interactive layer maps [http://gis.inl.gov/globalsites/ will redirect to 2018 update, http://gis.inl.gov/GlobalSurvey/] for selected: 1) deep mines and shafts; 2) existing, considered or planned radioactive waste management deep underground studies or disposal facilities 3) deep large diameter boreholes, 4) physics underground laboratories and facilities, and 5) deep open pit mines from around the world. These data are intended to facilitate user access to basic information and references regarding “deep underground” facilities, history, activities, and plans. In general, the interactive maps and database provide each facility’s approximate site location, geology, and engineered features (e.g.: access, geometry, depth, diameter, year of operations, groundwater, lithology, host unit name and age, basin; operator, management organization, geographic data, nearby cultural features, other). Although the survey is not all encompassing, it is a comprehensive review of many of the significant existing and historical underground facilities discussed in the literature addressing radioactive waste management and deep mined geologic disposal safety systems. The interactive map suite allows for a better appreciation of site area geographic and cultural settings. The global survey is intended to be used as a communication tool to support and inform: 1) interested parties and decision makers; 2) radioactive waste disposal and siting option evaluations, and 3) safety case development applicable to any mined geologic disposal facility as a demonstration (examples) of historical and current engineering and geotechnical capabilities available for use in deep underground facility siting, planning, construction, operations and monitoring.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Remote Sensing System (Engineering Change Proposal (ECP) 2)

The primary technical objective of this CRADA was for Sandia National Laboratories (SNL) and Northrop Grumman Systems Corporation, acting through Northrop Grumman Aerospace Systems (NGAS), to collaborate, as needed, to inform a Remote Sensing System (RSS) development, led by the NGAS CRADA partner, through its System Design Review (SDR) and subsequent Program Design Review (PDR) milestones. More specifically, tasks and deliverables involved SNL and NGAS collaborating in seven broad areas: System Engineering, System Modeling and Simulation, System and Component Design, Assessment and Implementation, System Integration and Testing, Data Path Design and Engineering and Collection Segment Processing Engineering and Implementation. The collaboration between SNL and NGAS has resulted in a benefit to both organizations, and the public/taxpayers, by ensuring that legacy knowledge is not lost to future developments and will be incorporated into ongoing and future U.S. sensor systems.

47 OTHER INSTRUMENTATION↗

ICME Guided Development of Advanced Cast Aluminum Alloys for Automotive Engine Applications (ADAPA)

Project Objectives: To develop a new class of advanced, cost competitive aluminum casting alloys providing a 25% improvement in component strength relative to components made with A319 or A356 alloys using sand and semi-permanent casting processes for high-performance engine applications. To demonstrate the power of Integrated Computational Materials Engineering (ICME) tools for accelerating the development of new materials and processing techniques, as well as to identify the gaps in ICME capabilities. To develop comprehensive cost models to ensure that components manufactured with these new alloys do not exceed 110% of the cost using incumbents alloys A319 or A356. To develop a technology transfer and commercialization plan for deployment of these new alloys in automotive engine applications. The key targets and baseline are shown in the table below.

36 MATERIALS SCIENCE↗

High Efficiency Cost Optimized - Spark Ignited Natural Gas Engines (HECO-SING) (Final Report)

The abundance of relatively low cost natural gas in the North American market, along with energy independence, makes natural gas attractive as an alternate fuel. Natural gas also has an advantage over diesel engines in low NOx emissions production. Natural gas does however have some technical challenges in its lower efficiency due to natural gas energy content in comparison to diesel or gasoline, which is also a partial factor in its vehicle storage capacity limitations and thus driving range. In order to address these challenges, the HECO-SING (High-Efficiency Cost-Optimized, Spark Ignited Natural Gas) project was undertaken. The goal was to increase engine efficiency (fuel economy), while still meeting future emissions, in a cost effective manner. In order to achieve these goals, high dilution combustion will be used with focus on advanced ignition systems, optimized aftertreatment selection, and creative engine controls are applied.

03 NATURAL GAS↗

Computationally Efficient Modeling of High Efficiency Clean Combustion Engines

This project focuses on the development and application of computationally efficient and accurate simulation tools for prediction of engine combustion. Simulation of combustion aids in development of new high-efficiency and low-emissions engines by allowing detailed characterization of in-cylinder engine processes that are difficult to measure directly. Simulation also allows exploratory investigations of new concepts, such as new combustion chamber geometry, allowing valuable and limited experimental resources to be focused on the most promising strategies.

30 DIRECT ENERGY CONVERSION↗

Brief 80 Nuclear Engineering Enrollments and Degrees Survey, 2017-2018 Data

The 2018 survey includes degrees granted for the academic years September 2016 – August 2017 and September 2017 – August 2018, and enrollments for fall 2018. Thirty-five nuclear engineering academic programs were surveyed with all 35 responding and data reported from 34 programs. The enrollments and degrees data include students majoring in nuclear engineering or in an option program equivalent to a major. Some nuclear engineering programs have indicated that health physics option enrollments and degrees are also reported in the health physics survey.

99 GENERAL AND MISCELLANEOUS↗

Foundations for Engineering Education for Distributed Energy Resources (FEEDER)

Foundations for Engineering Education for Distributed Energy Resources (FEEDER), as one of the four Distributed Technology Training Consortia (DTTCs) of the Grid Engineering for Accelerated Renewable Energy Deployment (GEARED) National Network, provided programs to meet the project goals, and works closely with the GEARED National Network Administrator (NNA) to foster student competence and career interest in advanced engineering and professional skills that support a robust electrical utility sector. This educational effort also included annual gatherings to share best practices and specific advances in knowledge, instructional best practice and educational integration throughout disciplines supporting power systems analysis and integration of distributed generation, with a focus on renewable energy. This effort aligned with the goals and objectives of the Department of Energy SunShot initiative. The project goals included the creation of a larger skilled electric grid workforce that is able to manage widespread deployment of distributed energy resources by developing and sharing new courses and curricula across the participating FEEDER institutions. FEEDER was expanded to add four institutions under the Solar Training & Education for Professionals (STEP) program, with the title Strategic Expansion to Achieve GEARED Goals and award number DE- EE0007327. Program components were selected based on gap analysis and advices of FEEDER industry advisory board, with a focus on student participation in power programs, research and formative experiences that led them to successful careers in power-related industries.

14 SOLAR ENERGY↗

Engineering Bioelectronic Signal Transduction Using the Bacterial Type III Secretion Apparatus

Engineering efficient methods for living systems to transfer electrical energy to non-living systems, at relevant size scales, continues to challenge our knowledge of materials and biology. Our goal was to enable signal transduction between cells and inorganic materials, using controlled electron transport as the energy transfer mechanism. We envision using the cell as a living battery, providing a set of environmental signals to trigger synthetic biological networks that divert intracellular electron transport pathways to inorganic extracellular structures. Conversely, changing electron influxes could guide cellular responses. It is challenging, however, to precisely engineer nanostructured materials to achieve controllable catalytic or electronic properties and connect them with biological energy sources. Our approach to this problem is to engineer protein scaffolds, taking advantage of the native recognition, selectivity and self-assembly properties of these nano-scale building blocks as well as their native intracellular localization patterns. We are using a type III secretion system (T3SS) needle protein from Salmonella enterica, PrgI, as a template for metal nanowire synthesis for biosensing and bioenergy applications. We demonstrate that purified PrgI monomers spontaneously self assemble into long filaments, and that high-affinity peptide tags specific for attachment to functionalized particles can be integrated into the N-terminal region of PrgI. The resulting filaments selectively bind to gold, whether the filaments are assembled in vitro, sheared from cells, or remain attached to live S. enterica cell membranes. Chemical reduction of the gold modified PrgI variants results in structures that are several microns in length and which incorporate a contiguous gold surface.

59 BASIC BIOLOGICAL SCIENCES↗

A Surety Engineering Framework and Process to Address Ethical Legal and Social Issues for Artificial Intelligence

The ethical, legal, and social issues (ELSI) surrounding Artificial Intelligence (AI) can have as great of an impact on the technologies’ success as technical issues such as safety, reliability, and security. Addressing these risks can counter potential program failures, legal and ethical battles, constraints to scientific research, and product vulnerabilities. This paper presents a surety engineering framework and process that can be applied to AI to identify and address technical, ethical, legal and societal risks. Extending sound engineering practices to incorporate a method to “engineer” ELSI can offer the scientific rigor required to significantly reduce the risk of AI vulnerabilities. Modeling the specification, design, evaluation and quality/risk indicators for AI provides a foundation for a risk-informed decision process that can benefit researchers and stakeholders alike as they use it to critically examine both substantial and intangible risks.

97 MATHEMATICS AND COMPUTING↗

Aluminum-clad Spent Nuclear Fuel Engineering Scale Drying Experiment Design

The purpose of this document is to provide the technical specifications for the Engineering Scale Design for the drying tests of aluminum-clad spent nuclear fuel (ASNF). The engineering scale design is to accommodate both forced helium drying (FHD) as well as vacuum drying. The experiments will employ mock ASNF assemblies with a limited number of chemically treated aluminum plates to simulate the aluminum hydroxides found on ASNF. The goal here is to understand the transformation that may occur in plates including the loss of chemisorbed water and changes in morphology. Physiosorbed and bulk water found in experiments will be dried in the process and the effect on drying operations noted. Decay heat will be simulated in one assembly using a custom designed resistance heating element. A typical radial arrangement of assemblies will be employed using a modified Type 1A Basket design. For the chamber/canister, a single assembly layer with full radial dimension will be employed. Modifications to the standard canister design and configuration include the addition of a siphon tube to enable recirculation of hot gas for forced helium drying. A ring of ports/flanges are added near the top of the chamber to accommodate the feedthroughs for instrumentation and power needed for the experiment and data collection. Four viewports are added to the main section of the chamber with two in line with one of the fuel assembly and siphon tube. The other two viewports are on the opposite side of the chamber. The purpose here is to provide the option of thermal imaging in addition to the nearly four dozen thermocouples available inside the chamber. Modeling of the chamber, basket, and mock ASNF assemblies was conducted to estimate temperature distributions throughout the chamber during forced helium drying and over the anticipated drying period. This modeling was used as input to decisions on the Engineering Scale Design. Work on modeling continues in the period during setup and testing to develop preliminary drying models. Analysis of experimental results will later be used to validate these and subsequent models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ICME Guided Development of Advanced Cast Aluminum Alloys for Automotive Engine Applications (ADAPA) (Final Report)

Project Objectives include the following: 1) To develop a new class of advanced, cost competitive aluminum casting alloys providing a 25% improvement in component strength relative to components made with A319 or A356 alloys using sand and semi-permanent casting processes for highperformance engine applications; 2) To demonstrate the power of Integrated Computational Materials Engineering (ICME) tools for accelerating the development of new materials and processing techniques, as well as to identify the gaps in ICME capabilities; 3) To develop comprehensive cost models to ensure that components manufactured with these new alloys do not exceed 110% of the cost using incumbent alloys A319 or A356; 4) To develop a technology transfer and commercialization plan for deployment of these new alloys in automotive engine applications; 5) The key targets and baseline are shown in the table below.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Development of Ionic Liquid-Additized, GF-5/6 Compatible Low-Viscosity Oils for Automotive Engine and Rear Axle Lubrication for 4% Improved Fuel Economy

This joint project among ORNL, GM, and DRO successfully developed ionic liquid-additized low viscosity lubricants, SAE 0W-12 and 70W-80, for both IC engine and rear axle lubrication, respectively, and demonstrated combined vehicle fuel economy improvement (FEI). Phosphonium-alkylphosphate ILs have been found to be the most effective among the candidates in protecting surface damage from both sliding wear and rolling contact fatigue, and optimal IL concentrations have been determined. The IL’s impact on three-way catalyst seems to be significantly less adverse than the conventional ZDDP. Oil formulations were optimized for both energy efficiency and wear protection. Tribological bench testing of the IL-additized low-viscosity oils showed at least 40% lower boundary friction, more than 60% lower elastohydrodynamic friction, and greater than 50% less wear compared with commercial baselines. IL-additized lubricants have demonstrated FEI by 9.9% in engine dynamometer tests under extreme conditions and 6.9% increased power output in gear rig tests. Prototype IL-additized engine oil and rear axle fluid exhibited combined FEI of 1.39% and 3.24% benchmarked against the state-of-the-art baselines in vehicle testing of fresh oils under the Federal Test Procedure (FTP) city cycle and Highway Fuel Economy Driving Schedule (HWFET), respectively. Used oil analysis suggested that the IL-additized low-viscosity oils produced less wear than the commercial baselines. The gained fundamental understanding and demonstrated FEI in this work pave the way for future development and implementation of the ionic liquid technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗