SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The challenge of the concept of a reusable, cargo carrying space vehicle, and how those challenges were met for the Space Shuttle are discussed. The complexity of the vehicle, the ground support systen, the onboard computer system, ramifications of a reusable vehicle, and the turn around objectives for Shuttle flights are outlined. The Apollo and the space transportation system (STS) are compared.
The Space Shuttle checkout is different from its Apollo predecessor. The complexity of the hardware, the shortened turnaround time, and the software that performs ground checkout are outlined. Generating new techniques and standards for software development and the management structure to control it are implemented. The utilization of computer systems for vehicle testing is high lighted.
The viscous, axisymmetric flow in the thrust chamber of the space shuttle main engine (SSME) was computed on the CRAY 205 computer using the general interpolants method (GIM) code. Results show that the Navier-Stokes codes can be used for these flows to study trends and viscous effects as well as determine flow patterns; but further research and development is needed before they can be used as production tools for nozzle performance calculations. The GIM formulation, numerical scheme, and computer code are described. The actual SSME nozzle computation showing grid points, flow contours, and flow parameter plots is discussed. The computer system and run times/costs are detailed.
Geologists obtain low accuracy levels when maps derived from LANDSAT MSS data are compared with those made by conventional methods. Procedures developed for the IDIMS computer system and used to classify a subset of a TM image of the Death Valley, California - Nevada border are described. Despite the superior resolution, broader spectral coverage, and greater sensitivity inherent to the TM, the actual recorded measured accuracy was in the same narrow range (30 to 60%) recorded for MSS data from earlier LANDSATs. The supervised classification approach appears to be superior to the unsupervised approach when applied to vegetation-sparse surfaces composed of spectrally contrasting rock/soil units distributed in relatively flat to low relief terrain. As spatial resolution improves and optimal spectral bands for identifying rock materials are specified, use of classified multispectral remote sensing data from air and space when coupled with supporting field calibration and checks should become the dominant way in which geologic mapping is carried out in future decades.
Preliminary plans for facility modifications and environmental/power systems for the JESS (Joint Exercise Support System) computer laboratory and Freedom Hall are presented. Blueprints are provided for each of the facilities and an estimate of the air conditioning requirements is given.
The Space Physics Analysis Network or SPAN is emerging as a viable method for solving an immediate communication problem for the space scientist. SPAN provides low-rate communication capability with co-investigators and colleagues, and access to space science data bases and computational facilities. The SPAN utilizes up-to-date hardware and software for computer-to-computer communications allowing binary file transfer and remote log-on capability to over 25 nationwide space science computer systems. SPAN is not discipline or mission dependent with participation from scientists in such fields as magnetospheric, ionospheric, planetary, and solar physics. Basic information on the network and its use are provided. It is anticipated that SPAN will grow rapidly over the next few years, not only from the standpoint of more network nodes, but as scientists become more proficient in the use of telescience, more capability will be needed to satisfy the demands.
A Human Operator Simulator (HOS) based pilot model has been developed for use at NASA LaRC for analysis of flight management problems. The model is currently configured to simulate piloted flight of an advanced transport airplane. The generic HOS operator and machine model was originally developed under U.S. Navy sponsorship by Analytics, Inc. and through a contract with LaRC was configured to represent a pilot flying a transport airplane. A version of the HOS program runs in batch mode on LaRC's (60-bit-word) central computer system. This document provides a guide for using the program and describes in some detail the assortment of files used during its operation.
This bibliography lists 706 reports, articles, and other documents introduced into the NASA scientific and technical information system in 1984. Entries, which include abstracts, are arranged in the following categories: human factors and personnel issues; management theory and techniques; industrial management and manufacturing; robotics and expert systems; computers and information management; research and development; economics, costs, and markets; logistics and operations management; reliability and quality control; and legality, legislation, and policy. Subject, personal author, corporate source, contract number, report number, and accession number indexes are included.
The preparation of remotely sensed data sets into a form useful to the analyst is a significant computational task, involving the processing of spacecraft data (e.g., orbit, attitude, temperatures, etc.), decommutation of the video telemetry stream, radiometric correction and geometric correction. Many of these processes are extremely well suited for implementation on attached array processors. Currently, at Goddard Space Flight Center a number of computer systems provide such capability for earth observations or are under development as test beds for future ground segment support. Six such systems will be discussed.
To demonstrate the high reliability of fault-tolerant computing systems, experimental testing can be performed by injecting faults into their hardware and observing the times needed to detect and isolate failed components and reconfigure the good components. Coverage, a parameter measuring continued system success, is the probability that recovery occurs before other, perhaps catastrophic, component failures occur. Methods of estimating coverage are given for the case of randomly selecting a subset of the pins or chips for testing. Pin-level samples of times to recovery are treated by the Type I censoring model often used in life testing.
It is pointed out that the increasing computation power and rapidly falling cost of microprocessors and memories have given an impetus to the development of distributed computing systems. There are a number of potential benefits. A number of issues have to be resolved, however, before the full potential of a distributed processing system can be realized. The present investigation is concerned with one such issue, taking into account the effectiveness of implementing recovery blocks (RB's) in backward error recovery for a set of cooperating processes. A quantitative evaluation of three different recovery blocks employed in backward error recovery for concurrent processing is performed.
A validation method for the synchronization subsystem of a fault-tolerant computer system is presented. The high reliability requirement of flight crucial systems precludes the use of most traditional validation methods. The method presented utilizes formal design proof to uncover design and coding errors and experimentation to validate the assumptions of the design proof. The experimental method is described and illustrated by validating an experimental implementation of the Software Implemented Fault Tolerance (SIFT) clock synchronization algorithm. The design proof of the algorithm defines the maximum skew between any two nonfaulty clocks in the system in terms of theoretical upper bounds on certain system parameters. The quantile to which each parameter must be estimated is determined by a combinatorial analysis of the system reliability. The parameters are measured by direct and indirect means, and upper bounds are estimated. A nonparametric method based on an asymptotic property of the tail of a distribution is used to estimate the upper bound of a critical system parameter. Although the proof process is very costly, it is extremely valuable when validating the crucial synchronization subsystem.
This is a tutorial article about language and architecture approaches for highly concurrent computer systems based on the functional style of programming. The discussion concentrates on the basic aspects of functional languages, and sequencing models such as data-flow, demand-driven and reduction which are essential at the machine organization level. Several examples of highly concurrent machines are described.
A concurrent processing algorithm for analysis of large aerospace structures is presented. A general description of the implementation criteria for the algorithm is given, and the results from applications to two vibration test problems are discussed. The test problems included a flexural vibration analysis of a long beam with 16 uniformly spaced supports, and a torsional vibration analysis. The computer system used to implement the algorithm was an experimental MIND system. The concurrent processing speedups for the test problems are given in a table.
The nonrecoverable stall condition in high performance turbofan engines is characterized by thrust loss, rising turbine temperatures, high pressure compressor rotating stall, and loss of engine control. Stall recovery control is presently investigated by means of an engine system computer model capable of either surge or rotating stall postinstability operation. Several techniques are examined which can yield rapid recovery from stall; a composite strategy which involves reduction of engine speed to idle while simultaneously opening the 10th- and 14th-stage compressor bleed ports allowed recovery to speeds slightly higher than idle while combustor fuel flow continued.
Status and some recent developments of computational models for tires are summarized. Discussion focuses on a number of aspects of tire modeling and analysis including: tire materials and their characterization; evolution of tire models; characteristics of effective finite element models for analyzing tires; analysis needs for tires; and impact of the advances made in finite element technology, computational algorithms, and new computing systems on tire modeling and analysis. An initial set of benchmark problems has been proposed in concert with the U.S. tire industry. Extensive sets of experimental data will be collected for these problems and used for evaluating and validating different tire models. Also, the new Aircraft Landing Dynamics Facility (ALDF) at NASA Langley Research Center is described.
As the complexity of NASA's planned Space Station design grows, decision-making must be transferred from the crew to an onboard computer system devised for maximum man/machine interactions productivity. The Space Station's electrical power subsystem is presently taken as an exemplary case of design evolution from the manual, through the automated, to the fully autonomous control regimes.
It is shown that single-event-upsets (SEUs) due to cosmic rays are a significant source of single bit error in spacecraft computers. The physical mechanism of SEU, electron hole generation by means of Linear Energy Transfer (LET), it discussed with reference made to the results of a study of the environmental effects on computer systems of the Galileo spacecraft. Techniques for making software more tolerant of cosmic ray effects are considered, including: reducing the number of registers used by the software; continuity testing of variables; redundant execution of major procedures for error detection; and encoding state variables to detect single-bit changes. Attention is also given to design modifications which may reduce the cosmic ray exposure of on-board hardware. These modifications include: shielding components operating in LEO; removing low-power Schottky parts; and the use of CMOS diodes. The SEU parameters of different electronic components are listed in a table.