Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CUTTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Effects of vane/blade ratio and spacing on fan noise

The effects of vane/blade ratio and spacing on fan noise are investigated to develop a fan noise prediction scheme which is calibrated against experimental data. A 44 blade, 0.504 diameter fan is used to demonstrate the production of fan noise data free from excess noise caused by rotor turbulence interaction. Two stator sets consisting of a cut-off set with 86 vanes, and a cut-on set of 48 vanes are used, with a total range of spacing from 0.5 to 2.3 rotor chords. The model includes viscous wake interaction noise and the potential field interactions of both the rotor and stator. A free-field acoustic environment is achieved by covering the walls, ceiling and floor with 0.7 m polyurethane foam wedges, providing less than + or - 1 dB standing wave ratio at 200 Hz. Only a 3 dB drop in tone level occurs as the spacing is increased from 0.5 to 2.3 rotor chords, and results indicate that the rotor wakes impinging on the stator vanes are the principal noise source for subsonic rotor speeds.

Kantola, R. A.↗
NASA NTRS1981

Auroral kilometric radiation source region observations from ISIS 1

The ISIS 1 observations of the high-frequency portion of the auroral kilometric radiation (AKR) spectrum are considered, that is, from the minimum frequency encountered for the extraordinary mode cut-off (approximately 450 kHz) to the upper frequency cut-off (approximately 800 kHz). AKR is found to be generated in the extraordinary mode just above the local cutoff frequency and to emanate in a direction that is nearly perpendicular to the magnetic field. It occurs within local depletions of electron density, where the ratio of plasma frequency to cyclotron frequency is below 0.2. The density depletion is restricted to altitudes above approximately 2,000 km, and the upper AKR frequency limit corresponds to the extraordinary cutoff frequency at this altitude.

Benson, R. F.↗
NASA NTRS1981

A data base approach for prediction of deforestation-induced mass wasting events

A major topic of concern in timber management is determining the impact of clear-cutting on slope stability. Deforestation treatments on steep mountain slopes have often resulted in a high frequency of major mass wasting events. The Geographic Information System (GIS) is a potentially useful tool for predicting the location of mass wasting sites. With a raster-based GIS, digitally encoded maps of slide hazard parameters can be overlayed and modeled to produce new maps depicting high probability slide areas. The present investigation has the objective to examine the raster-based information system as a tool for predicting the location of the clear-cut mountain slopes which are most likely to experience shallow soil debris avalanches. A literature overview is conducted, taking into account vegetation, roads, precipitation, soil type, slope-angle and aspect, and models predicting mass soil movements. Attention is given to a data base approach and aspects of slide prediction.

Logan, T. L.↗
NASA NTRS1983

Staked Bearing Removal Tool

Tool with assembled components expedites bearing replacement in aircraft, ground vehicles, and other applications. New tool cuts lip on one side to facilitate bearing replacement. After bearing retaining lip is cut away, bearing pressed out. Tool makes it possible to replace bearings without disassembling structure.

Berson, L. A.↗
NASA NTRS1984

Tool Enlarges Hard-to-Reach Holes

Tool centers itself and cuts precise depth. Tool consists of crosscut carbide bur; sleeve that serves as depth stop and pilot; length of flexible, strong piano wire; and standard drive socket. Parts brazed together. Piano wire transmits torque and axial force to cutting tool.

Geddes, J. P.↗
NASA NTRS1984

Bidirectional Continuous Coal Miner

Continuous mining machine cuts coal in both directions of travel eliminating downtime caused by retreating across face to start new cut.

Knurovsky, T.↗
NASA NTRS1984

Wire Electrical-Discharge Machining Aid

Rerouting cutting wire by adding idler rollers allows standard wire electrical-discharge machine (WEDM) temporarily modified to permit some types of cuts otherwise blocked.

Gollihugh, T.↗
NASA NTRS1982

Prediction of sound radiation from different practical jet engine inlets

Computer codes which were based upon a special integral representation of the external solutions of the Helmholtz equation were upgraded so that they would yield accurate results for the acoustic radiation patterns in the field surrounding an axisymmetric body for nondimensional wave numbers, based on duct radius, of up to twenty. The accuracy of these computer programs was checked by the use of the point source method for the generation of exact solutions and then by comparison with the results of other experimental and theoretical studies. These computer codes were used in a parametric study of the dependence of the radiated sound field on input modal distribution, wave number, and inlet lip shape. The results of this study show that: (1) as the wave number (i.e., cut off ratio) is increased for a given input modal distribution that the acoustic radiation peak moves towards the inlet centerline and becomes more compact (i.e., narrows); (2) as the input mode number is increased for a given cut off ratio the acoustic radiation peak moves away from the inlet centerline and becomes more compact.

Meyer, W. L.↗
NASA NTRS1981

LANDSAT applications by the Adirondack Park Agency for land cover analyses and forest cover change

The New York State Adirondack Park Agency is using LANDSAT imagery to provide current, consistent parkwide data on forest cover, forest change and other land cover characteristics for the Adirondack Park, an area of 9,375 sq. miles (24,280 sq km). Boundaries of the study area were digitized and the data were enhanced and geographically rectified. A classification scheme was devised which emphasized the basic land cover types of the Park: hardwoods, spruce-fir, pine, wet conifer, brushland, grassland, agricultural areas, exposed earth, urban areas, and water bodies. Cover type classifications for disturbed forest land were also chosen: cut hardwoods, regenerating hardwoods, and cut spruce fir. Field verification of 1978 classification revealed an accurate differentiation of forest types within types and between nonforested/forested areas. The classification accurately detects forest land disturbances; however, it is not always descriptive of the level of disturbance.

Banta, J. S.↗
NASA NTRS1983

A basis for the analysis of surface geometry of spiral bevel gears

Geometrical procedures helpful in the fundamental studies of the surface geometry of spiral bevel gears are summarized. These procedures are based upon: (1) fundamental gear geometry and kinematics as exposited by Buckingham, et al; (2) formulas developed from differential geometry; and (3) geometrical concepts developed in recent papers and reports on spiral bevel gear surface geometry. Procedures which characterize the geometry so that the surface parametric equations, the principal radii of curvature, and the meshing kinematics are systematically determined are emphasized. Initially, the focus in on theoretical, logarithmic spiral bevel gears as defined by Buckingham. The gears, however, are difficult to fabricate and are sometimes considered to be too straight. Circular-cut spiral bevel gears are an alternative to this. Surface characteristics of crown circular cut gears are analyzed.

Huston, R. L.↗
NASA NTRS1982

Generation of off-axis aspherics

A method for precise generation of optical surfaces is described. The work is turned about one axis, while a grinding head or cutting tool is gradually moved across by an arm turning about a second axis. This geometry can be used to directly generate spherical surfaces or aspherical surfaces presently termed 'hulahoids'. The properties of these surfaces are analyzed to determine how well large paraboloids and their off-axis segments can be generated. Very close approximations are possible. For example, 1.5-m segments of a 10-m paraboloid differ by only 0.6 microns peak-to-peak from the best fit hulahoid when the focal ratio is f/2, and 60 microns when it is f/0.4. For accurate generation the cutting tool may need numerically controlled travel of 1 mm or less, with the position set as a function of the swing arm angle.

Angel, J. R. P.↗
NASA NTRS1985

Automatic Coal-Mining System

Coal cutting and removal done with minimal hazard to people. Automatic coal mine cutting, transport and roof-support movement all done by automatic machinery. Exposure of people to hazardous conditions reduced to inspection tours, maintenance, repair, and possibly entry mining.

Collins, E. R., Jr.↗
NASA NTRS1983

High speed machining of space shuttle external tank liquid hydrogen barrel panel

Actual and projected optimum High Speed Machining data for producing shuttle external tank liquid hydrogen barrel panels of aluminum alloy 2219-T87 are reported. The data included various machining parameters; e.g., spindle speeds, cutting speed, table feed, chip load, metal removal rate, horsepower, cutting efficiency, cutter wear (lack of) and chip removal methods.

Hankins, J. D.↗
NASA NTRS1983

S-band SBAW microwave source, phase 2

Results of aging experiments on 1.072 GHz SBAW oscillators are discussed as well as the design, fabrication and test of 2.143 GHz SBAW delay lines. Two design approaches were implemented. The third harmonic transducer on 36 deg rotated Y cut quartz proved to be the most useful design, whereas the fifth harmonic transducer on - 50 5 deg rotated Y cut quartz suffered from high insertion loss and poor sidelobe rejection. The construction and characterization of the 2 GHz SBAW oscillator are described. Phase noise, frequency dependence on temperature, and 6-month aging were measured. Some SAW and SBAW oscillators were compared as were both the 1 and 2 GHz oscillators. The 2 GHz SBAW oscillator showed significant improvement in phase noise and temperature stability over the 2 GHz SAW oscillator developed in previous NASA programs. A technique to produce SBAW delay lines of different frequencies from a single mask is examined. The delay lines were incorporated into oscillator circuits to demonstrate the ability to select the frequency output of the SBAW oscillator.

Source record↗
NASA NTRS1984

A survey of payload integration methods

Several full-scale and short-cut methods for analyzing a booster/payload system are presented. Two full-scale techniques are considered: (1) a technique that uses a restrained payload together with a free-booster model, the latter being augmented with residual mass and stiffness correction and (2) a technique that uses a restrained payload and booster model. Both techniques determine the 'modal modes', which require the solution of a system eigenvalue problem; the loads usually are then determined via an acceleration approach. A brief description is given of a number of short-cut methods which are of special interest to Shuttle payload design: structural modification, base drive, and interface impedance methods. Directions for further research and development are suggested.

Engels, R. C.↗
NASA NTRS1985

Flushing Ring for EDM

Removing debris more quickly lowers cutting time. Operation, cutting oil and pressurized air supplied to ring placed around workpiece. Air forces oil through small holes and agitates oil as it flows over workpiece. High flow rate and agitation dislodge and remove debris. Electrical discharge removes material from workpiece faster.

Earwood, L.↗
NASA NTRS1985

Cutthrough Warning Circuit

Damage to underlying layer averted. Contact of cutter blade with metal shim completes circuit that warns cutting-tool operator to stop. Tool thus prevented from cutting into structural wall.

Mckown, R.↗
NASA NTRS1985

Coal-Sizing Auger

Aft end of auger, like forward, face-piercing end, equipped with hard cutting bits such as diamonds. As auger breaks face, pulls broken coal lumps into jaws and forces them into hardened throat section. There, cutting bits chew up lumps: Clearance between throat and auger shaft sets maximum size for coal particles that pass through. Auger motion pushes coal particles into mixing chamber, where paddles combine them with water.

Lewis, E. V.↗