Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Boundary layer flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Euler/Navier-Stokes zonal scheme with applications to separated and isolated-vortex flows

An Euler/Navier-Stokes zonal scheme with boundary-layer compatibility conditions is developed to economically compute separated and vortex flows. The scheme is based on dividing the flow region into zones, where different levels of mathematical approximations of the governing equations are used in each zone. The scheme is applied to two specific problems: the two dimensional flow over a blunt leading-edge plate and the quasi-axisymmetric flow of an isolated vortex core. In the first problem, the computational domain is divided into inner and outer zones where the Navier-Stokes and Euler equations are used, respectively. On the downstream boundary of the computational domain, boundary-layer compatibility conditions are used. In the second problem, boundary-layer-like equations for slender, compressible, vortex flows are developed. A compatibility condition has been used to ensure consistency of the boundary and initial conditions. The outer boundary conditions of the flow are derived from Euler equations for a stream surface.

Kandil, Osama A.↗

Effect of Compliant Walls on Secondary Instabilities in Boundary-Layer Transition

For aerodynamic and hydrodynamic vehicles, it is highly desirable to reduce drag and noise levels. A reduction in drag leads to fuel savings. In particular for submersible vehicles, a decrease in noise levels inhibits detection. A suggested means to obtain these reduction goals is by delaying the transition from laminar to turbulent flow in external boundary layers. For hydrodynamic applications, a passive device which shows promise for transition delays is the compliant coating. In previous studies with a simple mechanical model representing the compliant wall, coatings were found that provided transition delays as predicted from the semi-empirical e(sup n) method. Those studies were concerned with the linear stage of transition where the instability of concern is referred to as the primary instability. For the flat-plate boundary layer, the Tollmien-Schlichting (TS) wave is the primary instability. In one of those studies, it was shown that three-dimensional (3-D) primary instabilities, or oblique waves, could dominate transition over the coatings considered. From the primary instability, the stretching and tilting of vorticity in the shear flow leads to a secondary instability mechanism. This has been theoretical described by Herbert based on Floquet theory. In the present study, Herbert's theory is used to predict the development of secondary instabilities over isotropic and non-isotropic compliant walls. Since oblique waves may be dominant over compliant walls, a secondary theory extention is made to allow for these 3-D primary instabilities. The effect of variations in primary amplitude, spanwise wavenumber, and Reynolds number on the secondary instabilities are examined. As in the rigid wall case, over compliant walls the subharmonic mode of secondary instability dominates for low-amplitude primary disturbances. Both isotropic and non-isotropic compliant walls lead to reduced secondary growth rates compared to the rigid wall results. For high frequencies, the non-isotropic wall suppresses the amplification of the secondary instabilities, while instabilities over the isotropic wall may grow with an explosive rate similar to the rigid wall results. For the more important lower frequencies, both isotropic and non-isotropic compliant walls suppress the amplification of secondary instabilities compared to the rigid wall results. The twofold major discovery and demonstration of the present investigation are: (1) the use of passive devices, such as compliant walls, can lead to significant reductions in the secondary instability growth rates and amplification; (2) suppressing the primary growth rates and subsequent amplification enable delays in the growth of the explosive secondary instability mechanism.

Joslin, Ronald D.↗

Transition and laminar instability

The linear stability theory was applied to the problem of boundary layer transition in incompressible flow. The theory was put into a form suitable for three-dimensional boundary layers; both the temporal and spatial theories were examined; and a generalized Gaster relation for three-dimensional boundary layers was derived. Numerical examples include the stability characteristics of Falkner-Skan boundary layers, the accuracy of the two-dimensional Gaster relation for these boundary layers, and the magnitude and direction of the group velocity for oblique waves in the Blasius boundary layer. Available experiments which bear on the validity of stability theory and its relation to transition are reviewed and the stability theory is applied to transition prediction. The amplitude method is described in which the wide band disturbance amplitude in the boundary layer is estimated from stability theory and an interaction relation for the initial amplitude density of the most unstable frequency.

Mack, L. M.↗

Testing and Performance Verification of a High Bypass Ratio Turbofan Rotor in an Internal Flow Component Test Facility

A 1/5 scale model rotor representative of a current technology, high bypass ratio, turbofan engine was installed and tested in the W8 single-stage, high-speed, compressor test facility at NASA Glenn Research Center (GRC). The same fan rotor was tested previously in the GRC 9x15 Low Speed Wind Tunnel as a fan module consisting of the rotor and outlet guide vanes mounted in a flight-like nacelle. The W8 test verified that the aerodynamic performance and detailed flow field of the rotor as installed in W8 were representative of the wind tunnel fan module installation. Modifications to W8 were necessary to ensure that this internal flow facility would have a flow field at the test package that is representative of flow conditions in the wind tunnel installation. Inlet flow conditioning was designed and installed in W8 to lower the fan face turbulence intensity to less than 1.0 percent in order to better match the wind tunnel operating environment. Also, inlet bleed was added to thin the casing boundary layer to be more representative of a flight nacelle boundary layer. On the 100 percent speed operating line the fan pressure rise and mass flow rate agreed with the wind tunnel data to within 1 percent. Detailed hot film surveys of the inlet flow, inlet boundary layer and fan exit flow were compared to results from the wind tunnel. The effect of inlet casing boundary layer thickness on fan performance was quantified. Challenges and lessons learned from testing this high flow, low static pressure rise fan in an internal flow facility are discussed.

VanZante, Dale E.↗

Hypersonic Navier-Stokes Comparisons to Orbiter Flight Data

During the STS-119 flight of Space Shuttle Discovery, two sets of surface temperature measurements were made. Under the HYTHIRM program3 quantitative thermal images of the windward side of the Orbiter with a were taken. In addition, the Boundary Layer Transition Flight Experiment 4 made thermocouple measurements at discrete locations on the Orbiter wind side. Most of these measurements were made downstream of a surface protuberance designed to trip the boundary layer to turbulent flow. In this paper, we use the US3D computational fluid dynamics code to simulate the Orbiter flow field at conditions corresponding to the STS-119 re-entry. We employ a standard two-temperature, five-species finite-rate model for high-temperature air, and the surface catalysis model of Stewart.1 This work is similar to the analysis of Wood et al . 2 except that we use a different approach for modeling turbulent flow. We use the one-equation Spalart-Allmaras turbulence model8 with compressibility corrections 9 and an approach for tripping the boundary layer at discrete locations. In general, the comparison between the simulations and flight data is remarkably good

Candler, Graham V.↗

Analysis of High-Speed Aerodynamics of a Swept Wing with Seamless Flaps

Computational fluid dynamics (CFD) analysis was conducted to evaluate the high-speed aerodynamics of a Gulfstream GIII airplane (Gulfstream Aerospace Corporation, Savannah, Georgia) swept wing modified with an experimental seamless, compliant flap called the Adaptive Compliant Trailing Edge (ACTE) flap for airworthiness. The high-speed aerodynamics of the modified ACTE wing were analyzed at a Mach number of 0.85 and an altitude of 40,000 ft. A polyhedral finite-volume unstructured Reynolds-averaged Navier-Stokes CFD code was used with a two-equation turbulence model. Wing aerodynamics sensitivities to lift coefficients, airplane engine operation, vortex generators (VGs), and ACTE flap deflections were examined. High-speed flow over the clean GIII wing without VGs was found to be complex with outboard shock and boundary-layer interactions causing flow separation over the upper wing surface upstream of the aileron, which could result in buffet and controllability problems at higher lift coefficient values. The VGs were found to improve the high-speed aerodynamics of the clean wing, as expected; however, ACTE flap deflections of as little as 1 to 2 deg were found to negate all of the aerodynamic benefits provided by the VGs at high speeds.

wings↗

On the calculation of supersonic separating and reattaching flows

A method is developed for solving the laminar and turbulent compressible boundary layer equations for separating and reattaching flows. Results of this method are compared with experimental data for two laminar and three turbulent layer, shock wave interactions. Several Navier-Stokes solutions are obtained for each of the laminar boundary layer, shock wave interactions considered. Comparison of these solutions indicates a first order sensitivity in C sub f to the computational mesh selected in both the viscous and inviscid portions of the flow. Comparison of the present boundary layer solutions with the Navier-Stokes solutions and with data for a given Mach number indicates that as long as the separation bubble is small, the boundary layer approximation yields solutions whose accuracy is comparable to the Navier-Stokes solutions.

Murphy, J. D.↗

Experimental Investigation of Transition to Turbulence as Affected By Passing Wakes

This paper presents experimental results from a study of the effects of periodically passing wakes upon laminar-to-turbulent transition and separation in a low-pressure turbine passage. The test section geometry is designed to simulate unsteady wakes in turbine engines for studying their effects on boundary layers and separated flow regions over the suction surface by using a single suction surface and a single pressure surface to simulate a single turbine blade passage. Single-wire, thermal anemometry techniques are used to measure time-resolved and phase averaged, wall-normal profiles of velocity, turbulence intensity and intermittency at multiple streamwise locations over the turbine airfoil suction surface. These data are compared to steady-state wake-free data collected in the same geometry to identify the effects of wakes upon laminar-to-turbulent transition. Results are presented for flows with a Reynolds number based on suction surface length and stage exit velocity of 50,000 and an approach flow turbulence intensity of 2.5%. While both existing design and experimental data are primarily concerned with higher Reynolds number flows (Re greater than 100,000), recent advances in gas turbine engines, and the accompanying increase in laminar and transitional flow effects, have made low-Re research increasingly important. From the presented data, the effects of passing wakes on transition and separation in the boundary layer, due to both increased turbulence levels and varying streamwise pressure gradients are presented. The results show how the wakes affect transition. The wakes affect the flow by virtue of their difference in turbulence levels and scales from those of the free-stream and by virtue of their ensemble- averaged velocity deficits, relative to the free-stream velocity, and the concomitant changes in angle of attack and temporal pressure gradients. The relationships between the velocity oscillations in the freestream and the unsteady velocity profile shapes in the near-wall flow are described. In this discussion is support for the theory that bypass transition is a response of the near-wall viscous layer to pressure fluctuations imposed upon it from the free-stream flow. Recent transition models are based on that premise. The data also show a significant lag between when the wake is present over the surface and when transition begins.cous layer to pressure fluctuations imposed upon it from the free-stream flow. Recent transition models are based on that premise. The data also show a significant lag between when the wake is present over the surface and when transition begins.cous layer to pressure fluctuations imposed upon it from the free-stream flow. Recent transition models are based on that premise. The data also show a significant lag between when the wake is present over the surface and when transition begins.

Kaszeta, Richard W.↗

Effects of simulated combustor turbulence on boundary layer heat transfer

A simulated combustor flow field has been generated in order to study the effects of high intensity large scale turbulence on boundary layer heat transfer. Turbulence intensities of up to 19 percent and integral lengths scales of 4 to 6 centimeters have been generated. Heat transfer has been augmented by up to 28 percent for the flat plate constant velocity turbulent boundary layer.

Ames, F. E.↗

Turbulence Modeling for Shock Wave/Turbulent Boundary Layer Interactions

Accurate aerodynamic computational predictions are essential for the safety of space vehicles, but these computations are of limited accuracy when large pressure gradients are present in the flow. The goal of the current project is to improve the state of compressible turbulence modeling for high speed flows with shock wave / turbulent boundary layer interactions (SWTBLI). Emphasis will be placed on models that can accurately predict the separated region caused by the SWTBLI. These flows are classified as nonequilibrium boundary layers because of the very large and variable adverse pressure gradients caused by the shock waves. The lag model was designed to model these nonequilibrium flows by incorporating history effects. Standard one- and two-equation models (Spalart Allmaras and SST) and the lag model will be run and compared to a new lag model. This new model, the Reynolds stress tensor lag model (lagRST), will be assessed against multiple wind tunnel tests and correlations. The basis of the lag and lagRST models are to preserve the accuracy of the standard turbulence models in equilibrium turbulence, when the Reynolds stresses are linearly related to the mean strain rates, but create a lag between mean strain rate effects and turbulence when nonequilibrium effects become important, such as in large pressure gradients. The affect this lag has on the results for SWBLI and massively separated flows will be determined. These computations will be done with a modified version of the OVERFLOW code. This code solves the RANS equations on overset grids. It was used for this study for its ability to input very complex geometries into the flow solver, such as the Space Shuttle in the full stack configuration. The model was successfully implemented within two versions of the OVERFLOW code. Results show a substantial improvement over the baseline models for transonic separated flows. The results are mixed for the SWBLI assessed. Separation predictions are not as good as the baseline models, but the over prediction of the peak heat flux downstream of the reattachment shock that plagues many models is reduced.

Lillard, Randolph P.↗

Some features of unsteady separating turbulent boundary layers

The physical features of steady and unsteady separating turbulent boundary layers are discussed with reference to wind-tunnel data obtained at a Reynolds number of 5.1 x 10 to the 6th and a reduced frequency of 0.55. It is shown that a moderate-amplitude (R less than 0.3) oscillating turbulent boundary layer has a mean flow structure that is close to that of a steady free-stream turbulent boundary layer. Well upstream of the separation, unexpected phase shifts of the velocity and turbulence oscillations occur near the wall between the viscous sublayer and the semilogarithmic region. Significant phase variations between the velocity and turbulence also exist in the detached and back flows downstream. Large amplitude oscillations are shown to have a substantial effect on the flow structure.

Simpson, R. L.↗

Thermodynamic evaluation of transonic compressor rotors using the finite volume approach

Progress made in extending the finite volume explicit time marching method to laminar and turbulent flow during the time period from January to May 1985 is documented. Previously, extensions were made to the finite volume method to improve the accuracy of the calculation of total pressure in compressible inviscid flow. The current work extends these ideas and develops new ideas which allow the calculation of laminar and turbulent boundary layers in internal flows. The method is verified using four test cases with free-stream Mach numbers ranging from .075 to 1.20.

Nicholson, S.↗

Modeling the Gas Dynamics Environment in a Subscale Solid Rocket Test Motor

Subscale test motors are often used for the evaluation of solid rocket motor component materials such as internal insulation. These motors are useful for characterizing insulation performance behavior, screening insulation material candidates and obtaining material thermal and ablative property design data. One of the primary challenges associated with using subscale motors however, is the uncertainty involved when extrapolating the results to full-scale motor conditions. These uncertainties are related to differences in such phenomena as turbulent flow behavior and boundary layer development, propellant particle interactions with the wall, insulation off-gas mixing and thermochemical reactions with the bulk flow, radiation levels, material response to the local environment, and other anomalous flow conditions. In addition to the need for better understanding of physical mechanisms, there is also a need to better understand how to best simulate these phenomena using numerical modeling approaches such as computational fluid dynamics (CFD). To better understand and model interactions between major phenomena in a subscale test motor, a numerical study of the internal flow environment of a representative motor was performed. Simulation of the environment included not only gas dynamics, but two-phase flow modeling of entrained alumina particles like those found in an aluminized propellant, and offgassing from wall surfaces similar to an ablating insulation material. This work represents a starting point for establishing the internal environment of a subscale test motor using comprehensive modeling techniques, and lays the groundwork for improving the understanding of the applicability of subscale test data to full-scale motors. It was found that grid resolution, and inclusion of phenomena in addition to gas dynamics, such as two-phase and multi-component gas composition are all important factors that can effect the overall flow field predictions.

Eaton, Andrew M.↗

Heat Transfer Measurements on the Endwall of a Variable Speed Power Turbine Blade Cascade

Heat transfer measurements were obtained on the endwall of a 2-D section of a variable speed power turbine (VSPT) rotor blade linear cascade. Infrared thermography was used to help determine the transition of flow from laminar to turbulent as well as determine regions of flow separation. Steady state data was obtained for six incidence angles ranging from +15.8 deg to -51 deg, and at five flow conditions for each angle. Nusselt number was used as a method to visualize flow transition and separation on the endwall surface and showed the effects of secondary flows on the surface. Nusselt correlation with Reynolds number from multiple flow conditions was used to plot local values of the correlation exponent and indicated the state of the local boundary layer as the flow transitioned from laminar to turbulent as well as secondary flow features.

variable speed power turbine↗

The boundary layer on compressor cascade blades

The purpose of NASA Research Grant NSG-3264 is to characterize the flowfield about an airfoil in a cascade at chord Reynolds number(R sub C)near 5 x 10 to the 5th power. The program is experimental and combines laser Doppler velocimeter (LDV) measurements with flow visualization techniques in order to obtain detailed flow data, e.g., boundary layer profiles, points of separation and the transition zone, on a cascade of highly-loaded compressor blades. The information provided by this study is to serve as benchmark data for the evaluation of current and future compressor cascade predictive models, in this way aiding in the compressor design process. Summarized is the research activity for the period 1 December 1985 through 1 June 1986. Progress made from 1 June 1979 through 1 December 1985 is presented. Detailed measurements have been completed at the initial cascade angle of 53 deg. (incidence angle 5 degrees). A three part study, based on that data, has been accepted as part of the 1986 Gas Turbine Conference and will be submitted for subsequent journal publication. Also presented are data for a second cascade angle of 45 deg (an incidence angle of 3 degrees).

Deutsch, S.↗