Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aircraft structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,621 records · Page 90

Aeropropulsion 1979

State of the art technology in aeronautical propulsion is assessed. Noise and air pollution control techniques, advances in supersonic propulsion for transport aircraft, and composite materials and structures for reliable engine components are covered along with engine design for improved fuel consumption.

Source record↗

Wind-tunnel tests of the XV-15 tilt rotor aircraft

The XV-15 aircraft was tested in the Ames 40 by 80 Foot Wind Tunnel for preliminary evaluation of aerodynamic and aeroelastic characteristics prior to flight. The tests were undertaken to investigate the aircraft performance, stability, control and structural loads for flight modes from helicopter through transition and airplane mode up to the tunnel capability of 170 knots. Results from these tests are presented.

Weiberg, J. A.↗

An investigation into the probabilistic combination of quasi-static and random accelerations

The development of design load factors are investigated for aerospace and aircraft components and experiment support structures, which are subject to a simultaneous vehicle dynamic vibration and acoustically generated random vibration. The characteristics of the combined acceleration probability density function is determined, and an appropriate percentile level for the combined acceleration is selected. This mechanism is developed and graphical data is provided to select combined accelerations for most popular percentile levels.

Schock, R. W.↗

An investigation into the probabilistic combination of quasi-static and random accelerations

The development of design load factors for aerospace and aircraft components and experiment support structures, which are subject to a simultaneous vehicle dynamic vibration (quasi-static) and acoustically generated random vibration, require the selection of a combination methodology. Typically, the procedure is to define the quasi-static and the random generated response separately, and arithmetically add or root sum square to get combined accelerations. Since the combination of a probabilistic and a deterministic function yield a probabilistic function, a viable alternate approach would be to determine the characteristics of the combined acceleration probability density function and select an appropriate percentile level for the combined acceleration. The following paper develops this mechanism and provides graphical data to select combined accelerations for most popular percentile levels.

Schock, R. W.↗

Turbulence forecasting

In order to forecast turbulence, one needs to have an understanding of the cause of turbulence. Therefore, an attempt is made to show the atmospheric structure that often results when aircraft encounter moderate or greater turbulence. The analysis is based on thousands of hours of observations of flights over the past 39 years of aviation meteorology.

Chandler, C. L.↗

Properties and potential applications of brominated P-100 carbon fibers

A review of the properties and potential applications of bromine-intercalated pitch-based carbon fibers is presented. The dynamics of the intercalation reaction are summarized, and characteristics, such as resistivity, density, and stability, are discussed. In addition, the mechanical and electrical properties of bromine-intercalated fiber-epoxy conposites will be addressed. With conductivities comparable to stainless steel, these brominated carbon fibers may be used in a number of composite applications, such as electromagnetic interference shielding containers, large conductive space structures, lightning strike-tolerant aircraft surfaces, and aircraft deicing applications.

Jaworske, D. A.↗

Correlations between ozone and carbon monoxide in the lower stratosphere, folded tropopause, and maritime troposphere

The variations of ozone and carbon monoxide with respect to the atmospheric flow structure are investigated for two aircraft flights: one in the upper troposphere/lower stratosphere over the continental United States on April 20, 1984, and the other in the marine troposphere over the eastern Pacific on April 26, 1984. The high frequency (1 Hz) and precision of the measurements allow detailed analysis of the species distribution down to length scales of the order of 1 km. Correlations between the two species are made on large, medium, and small scales of motion, and the results are interpreted. In general, the correlations are negative with some regions of positive correlation. The interpretation of these results is discussed.

Hipskind, R. Stephen↗

Electro-impulse de-icing - A status report

The advantages and disadvantages of the Electro-Impulse De-Icing (EIDI) system are examined. The design and operation of the EIDI are described. The effect of repeated impulsive loads on the structure and skin of the aircraft surface is investigated. It is observed that the wing skin directly over the coil receives the greatest stresses. Data from the testing of metal leading edges reveal that after 11,500 impulses cracks appear in the sheet brackets attaching the ribs to the coil beams. The composite leading edge was evaluated for fatigue, and after 20,000 impulses no cracks were detected. The advantages of the band-aid coil mount are discussed.

Zumwalt, G. W.↗

Interior noise control ground test studies for advanced turboprop aircraft applications

The measurement and analysis procedures are documented, and the results of interior noise control ground tests conducted on a DC-9 aircraft test section are summarized. The objectives of these tests were to study the fuselage response characteristics of treated and untreated aircraft with aft-mount advanced turboprop engines and to analyze the effectiveness of selected noise control treatments in reducing passenger cabin noise on these aircraft. The results of fuselage structural mode surveys, cabin cavity surveys and sound intensity surveys are presented. The performance of various structural and cabin sidewall treatments is assessed, based on measurements of the resulting interior noise levels under simulated advanced turboprop excitation.

Simpson, Myles A.↗

LaRC computational dynamics overview

Present research centers on the development of advanced computational methods for transient simulation analyses. Aircraft, launch vehicles and space structure components are potential applications, but primary focus is presently on large space structures. There are both in-house and out-of-house activities. The in-house activity centers around the development of a multibody simulation tool for truss-like structures called LATDYN for Large Angle Transient DYNamics. Multibody analysis involves articulation of structural components as well as robotic maneuvers. These items are necessary for construction (erection or deployment) of large space structures in orbit and the carrying out of certain operations on board the space station. Thus, part of the in-house activity involves the development of methods which treat the changing mass, stiffness and constraints associated with articulating systems. The out-of-house activity involves subcycling, development of large deformation/motion beam formulation, constraint stabilization and direct time integration transient algorithms in parallel computing.

Husner, J. M.↗

Finite element mesh refinement criteria for stress analysis

This paper discusses procedures for finite-element mesh selection and refinement. The objective is to improve accuracy. The procedures are based on (1) the minimization of the stiffness matrix race (optimizing node location); (2) the use of h-version refinement (rezoning, element size reduction, and increasing the number of elements); and (3) the use of p-version refinement (increasing the order of polynomial approximation of the elements). A step-by-step procedure of mesh selection, improvement, and refinement is presented. The criteria for 'goodness' of a mesh are based on strain energy, displacement, and stress values at selected critical points of a structure. An analysis of an aircraft lug problem is presented as an example.

Kittur, Madan G.↗

Analyzing the flared landing task with pitch-rate flight control systems

A closed-loop handling qualities methodology is applied to an analysis of the flared landing task with pitch-rate flight control systems. A model of pilot behavior throughout approach and flare is developed which postulates the manner in which the pilot may move from pitch attitude to flight path angle control. Twenty-five configurations flight tested on the NC-131H Total In-flight Simulator aircraft are analyzed using a structural pilot model ad a handling qualities methodology previously reported in the literature. Closed-loop simulation of the simplified landing task is undertaken using the structural model. The pilot ratings from flight test extended the data base supporting the utility of a model-based handling qualities metric. A handling qualities sensitivity function is introduced which may have potential as a design tool.

Hess, Ronald A.↗

Automated Characterization Of Vibrations Of A Structure

Automated method of characterizing dynamical properties of large flexible structure yields estimates of modal parameters used by robust control system to stabilize structure and minimize undesired motions. Based on extraction of desired modal and control-design data from responses of structure to known vibrational excitations. Applicable to terrestrial structures where vibrations are important - aircraft, buildings, bridges, cranes, and drill strings.

Bayard, David S.↗

Simplified signal processing for an airborne CO2 Doppler lidar

In the development of the National Center for Atmospheric Research (NCAR) airborne infrared lidar system (NAILS), we have emphasized a simple, modular design to suit the instrument to its mission of providing measurements of atmospheric structure and dynamics from an aircraft platform. Based on our research to this point, we believe that a significant simplification of the signal processing approach compared to that now used is possible by using high speed digitization of the signal. The purpose here is to place signal processing in the context of the overall system design and to explore the basis of the alternative technique so that the community can comment on the approach.

Schwiesow, R. L.↗

GPS interferometric attitude and heading determination - Flight test results

Methods and results for realtime pitch, roll, and heading determination of a dynamic flexible platform are presented. Consideration is given to a GPS attitude and heading determination system installed in Ohio University's Douglas DC-3 research aircraft. Signals from four antennas are processed by an Ashtech 3DF 24-channel GPS receiver. Data from the receiver are sent to a microcomputer for storage and further computations. Attitude and heading data are sent to a second computer for display on a software generated artificial horizon. Demonstration of this technique proves its candidacy for augmentation of aircraft state estimation for flight control and navigation as well as for numerous other applications, such as reliable aircraft state estimation, measurement of structural flexing of large space structures, synthetic aperture radar, aerial photogrammetry, pointing systems, spacecraft attitude control, rendezvous and docking, and road mapping.

Van Graas, Frank↗

Observations with the ROWS instrument during the Grand Banks calibration/validation experiments

As part of a global program to validate the ocean surface sensors on board ERS-1, a joint experiment on the Grand Banks of Newfoundland was carried out in Nov. 1991. The principal objective was to provide a field validation of ERS-1 Synthetic Aperture Radar (SAR) measurement of ocean surface structure. The NASA-P3 aircraft measurements made during this experiment provide independent measurements of the ocean surface along the validation swath. The Radar Ocean Wave Spectrometer (ROWS) is a radar sensor designed to measure direction of the long wave components using spectral analysis of the tilt induced radar backscatter modulation. This technique greatly differs from SAR and thus, provides a unique set of measurements for use in evaluating SAR performance. Also, an altimeter channel in the ROWS gives simultaneous information on the surface wave height and radar mean square slope parameter. The sets of geophysical parameters (wind speed, significant wave height, directional spectrum) are used to study the SAR's ability to accurately measure ocean gravity waves. The known distortion imposed on the true directional spectrum by the SAR imaging mechanism is discussed in light of the direct comparisons between ERS-1 SAR, airborne Canadian Center for Remote Sensing (CCRS) SAR, and ROWS spectra and the use of the nonlinear ocean SAR transform.

Vandemark, D.↗

Design and testing of an oblique all-wing supersonic transport

This report describes the preliminary design of an Oblique All-Wing (OAW) supersonic transport and a corresponding wind-tunnel model that was tested in the NASA Ames 9- by 7-Foot supersonic wind tunnel. The main goal was the determination of the cruise performance (lift/drag ratio) of a realistically configured OAW. To achieve an acceptable level of realism, it was necessary to consider many issues of design practicality such as the need for a viable propulsion system, adequate control surfaces, landing gear, provisions for 450 passengers, and fuel to fly 5,000 nautical miles. The aircraft had to be stable, structurally sound, and needed to fit into airports across the world. Support was directed primarily towards integration of the propulsion system, however, there were notable contributions to many aspects of the configuration design, wind tunnel model, and wind tunnel test.

Lee, Christopher A.↗

Fracture Mechanics of Thin, Cracked Plates Under Tension, Bending and Out-of-Plane Shear Loading

Cracks in the skin of aircraft fuselages or other shell structures can be subjected to very complex stress states, resulting in mixed-mode fracture conditions. For example, a crack running along a stringer in a pressurized fuselage will be subject to the usual in-plane tension stresses (Mode-I) along with out-of-plane tearing stresses (Mode-III like). Crack growth and initiation in this case is correlated not only with the tensile or Mode-I stress intensity factor, K(sub I), but depends on a combination of parameters and on the history of crack growth. The stresses at the tip of a crack in a plate or shell are typically described in terms of either the small deflection Kirchhoff plate theory. However, real applications involve large deflections. We show, using the von-Karman theory, that the crack tip stress field derived on the basis of the small deflection theory is still valid for large deflections. We then give examples demonstrating the exact calculation of energy release rates and stress intensity factors for cracked plates loaded to large deflections. The crack tip fields calculated using the plate theories are an approximation to the actual three dimensional fields. Using three dimensional finite element analyses we have explored the relationship between the three dimensional elasticity theory and two dimensional plate theory results. The results show that for out-of-plane shear loading the three dimensional and Kirchhoff theory results coincide at distance greater than h/2 from the crack tip, where h/2 is the plate thickness. Inside this region, the distribution of stresses through the thickness can be very different from the plate theory predictions. We have also explored how the energy release rate varies as a function of crack length to plate thickness using the different theories. This is important in the implementation of fracture prediction methods using finite element analysis. Our experiments show that under certain conditions, during fatigue crack growth, the presence of out-of-plane shear loads induces a great deal of contact and friction on the crack surfaces, dramatically reducing crack growth rate. A series of experiments and a proposed computational approach for accounting for the friction is discussed.

Zehnder, Alan T.↗