Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “variable geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Transonic off-design drag and performance of an axisymmetric inlet with 40 percent internal contraction on design

An experimental investigation determined the drag and pressure performance of an axisymmetric supersonic inlet when operated in the transonic speed range. The inlet configuration was derived from a Mach 2.5 mixed compression inlet design with assumed variable geometry. At typical engine airflows the drag coefficient varied from 0.057 to 0.192 when the Mach number changed from 0.80 to 1.27. The presence of a wing simulator resulted in a sizable increase in total drag at Mach 1.2. This interference drag, which is roughly a 0.1 increase in drag coefficient, originates equally from an increase in both additive and cowl pressure drag.

Woollett, R. R.↗
NASA NTRS1973

Advanced technology for reducing aircraft engine pollution

The proposed EPA regulations covering emissions of gas turbine engines will require extensive combustor development. The NASA is working to develop technology to meet these goals through a wide variety of combustor research programs conducted in-house, by contract, and by university grant. In-house efforts using the swirl-can modular combustor have demonstrated sizable reduction in NO emission levels. Testing to reduce idle pollutants has included the modification of duplex fuel nozzles to air-assisted nozzles and an exploration of the potential improvements possible with combustors using fuel staging and variable geometry. The Experimental Clean Combustor Program, a large contracted effort, is devoted to the testing and development of combustor concepts designed to achieve a large reduction in the levels of all emissions. This effort is planned to be conducted in three phases with the final phase to be an engine demonstration of the best reduced emission concepts.

Jones, R. E.↗
NASA NTRS1975

A summary of experimental research on propulsive-lift concepts in the Langley 16-foot transonic tunnel

A summary of research on both conceptual and practical configurations in which the aircraft's powerplant is integrated to take advantage of propulsion-induced aerodynamics conducted in the Langley 16-foot transonic tunnel has been made. These investigations included: (1) vectoring a partial-span jet exhaust at a wing trailing edge; (2) thrust vectoring characteristics of a twin, two-dimensional variable-geometry wedge nozzle; (3) a jet exhaust/upper surface blowing concept for fighter aircraft; and (4) jets blowing over the wing. These studies indicate a potential for increasing maneuverability of fighter aircraft at high lift coefficients. With proper integration of the powerplant and the airframe, significant improvements in cruise performance of both fighter and transport aircraft are possible.

Capone, F. J.↗
NASA NTRS1975

Feasibility of a 30-meter space based laser transmitter

A study was made of the application of large expandable mirror structures in future space missions to establish the feasibility and define the potential of high power laser systems for such applications as propulsion and power transmission. Application of these concepts requires a 30-meter diameter, diffraction limited mirror for transmission of the laser energy. Three concepts for the transmitter are presented. These concepts include consideration of continuous as well as segmented mirror surfaces and the major stow-deployment categories of inflatable, variable geometry and assembled-in-space structures. The mirror surface for each concept would be actively monitored and controlled to maintain diffraction limited performance at 10.6 microns during operation. The proposed mirror configurations are based on existing aerospace state-of-the-art technology. The assembled-in-space concept appears to be the most feasible, at this time.

Berggren, R. R.↗
NASA NTRS1976

Aerodynamic and acoustic performance of a contracting cowl high throat Mach number inlet installed on NASA quiet engine C

The approach and takeoff performance was evaluated of a contracting cowl variable geometry design inlet installed on a high-bypass-ratio turbofan engine. The design was finalized after consideration of aerodynamic, acoustic, and mechanical factors which would lead to a viable flight worthy concept. The aerodynamic results are presented in terms of inlet recovery and distortion parameter as functions of throat Mach number, and acoustic results in terms of Perceived Noise Level. The contracting cowl high throat Mach number inlet is shown to be an attractive means to reduce forward radiated noise from a high bypass ratio turbofan engine.

Blommer, H. E.↗
NASA NTRS1976

The effect of helicopter main rotor blade phasing and spacing on performance, blade loads, and acoustics

The performance, blade loads, and acoustic characteristics of a variable geometry rotor (VGR) system in forward flight and in a pullup maneuver were determined by the use of existing analytical programs. The investigation considered the independent effects of vertical separation of two three-bladed rotor systems as well as the effects of azimuthal spacing between the blades of the two rotors. The computations were done to determine the effects of these parameters on the performance, blade loads, and acoustic characteristics at two advance ratios in steady-state level flight and for two different g pullups at one advance ratio. To evaluate the potential benefits of the VGR concept in forward flight and pullup maneuvers, the results were compared as to performance, oscillatory blade loadings, vibratory forces transmitted to the fixed fuselage, and the rotor noise characteristics of the various VGR configurations with those of the conventional six-bladed rotor system.

Gangwani, S. T.↗
NASA NTRS1976

Aerodynamic and acoustic performance of a contracting cowl high throat Mach number inlet installed on NASA Quiet Engine 'C'

The purpose of this experimental program was to evaluate the approach and takeoff performance of a contracting cowl variable geometry design inlet installed on a high-bypass-ratio turbofan engine. The design was finalized after consideration of aerodynamic, acoustic, and mechanical factors which would lead to a viable flight-worthy inlet concept. The aerodynamic results are presented in terms of inlet recovery and distortion parameter as functions of throat Mach number, and acoustic results in terms of Perceived Noise Level. The contracting cowl high throat Mach number inlet is shown to be an attractive means to reduce forward radiated noise from a high bypass ratio turbofan engine.

Bloomer, H. E.↗
NASA NTRS1976

Aeroacoustics: Fan noise and control; Duct acoustics; Rotor noise

The recent progress in duct acoustic research is reflected by fourteen papers which cover essentially the areas of linear duct acoustics, the characteristics of absorbent materials, and nonlinear duct acoustics. With respect to propagation in ducts, emphasis is placed on computational methods aimed at attaining effective economical modeling of propagation in variable-geometry and in hard-wall or soft-wall ducts. Computational methods developed to reduce computer processing and storage requirements are outlined, along with a wave envelope technique for reducing processing and storage needs. The latter technique is applied to the optimum segmented acoustic duct linear design. A finite difference technique is used in combination with conformal mapping to compute the optimum multisection duct linear design.

Schwartz, I. R.↗
NASA NTRS1976

Flight experience with a digital integrated propulsion control system on an F-111E airplane

A digital integrated propulsion control system (IPCS) installed in the left side of an F-111 E aircraft was tested in flight. The F-111 aircraft was selected for the IPCS program because it incorporated a variable geometry inlet and an afterburning turbofan engine and had two engines, one of which could remain in the normal configuration to ensure flight safety. Flight data were compared with results of tests run in an altitude test chamber. The digital system was found to be capable of duplicating the standard engine and inlet control systems. Instabilities such as inlet buzz and afterburner rumble were detected and controlled. The usefulness of an altitude chamber for developing a software and testing hardware was proven. The flexibility of IPCS was demonstrated when an autothrottle, an in-flight thrust calculation, and a coannular noise study capability were added at the end of the flight tests.

Burcham, F. W., Jr.↗
NASA NTRS1976

An Analytical Study for Subsonic Oblique Wing Transport Concept

The oblique wing concept has been investigated for subsonic transport application for a cruise Mach number of 0.95. Three different mission applications were considered and the concept analyzed against the selected mission requirements. Configuration studies determined the best area of applicability to be a commercial passenger transport mission. The critical parameter for the oblique wing concept was found to be aspect ratio which was limited to a value of 6.0 due to aeroelastic divergence. Comparison of the concept final configuration was made with fixed winged configurations designed to cruise at Mach 0.85 and 0.95. The crossover Mach number for the oblique wing concept was found to be Mach 0.91 for takeoff gross weight and direct operating cost. Benefits include reduced takeoff distance, installed thrust and mission block fuel and improved community noise characteristics. The variable geometry feature enables the final configuration to increase range by 10% at Mach 0.712 and to increase endurance by as much as 44%.

Bradley, E. S.↗
NASA NTRS1976

Advanced supersonic propulsion study, phase 3

The variable stream control engine is determined to be the most promising propulsion system concept for advanced supersonic cruise aircraft. This concept uses variable geometry components and a unique throttle schedule for independent control of two flow streams to provide low jet noise at takeoff and high performance at both subsonic and supersonic cruise. The advanced technology offers a 25% improvement in airplane range and an 8 decibel reduction in takeoff noise, relative to first generation supersonic turbojet engines.

Howlett, R. A.↗
NASA NTRS1976

Simulator study of the low-speed handling qualities of a supersonic cruise arrow-wing transport configuration during approach and landing

A fixed-based simulator study was conducted to determine the low-speed flight characteristics of an advanced supersonic cruise transport having an arrow wing, a horizontal tail, and four dry turbojets with variable geometry turbines. The primary piloting task was the approach and landing. The statically unstable (longitudinally) subject configuration has unacceptable low-speed handling qualities with no augmentation. Therefore, a hardened stability augmentation system is required to achieve acceptable handling qualities, should the normal operational stability and control augmentation system fail. In order to achieve satisfactory handling qualities, considerable augmentation was required.

Grantham, W. D.↗
NASA NTRS1976

Evaluation of a staged fuel combustor for turboprop engines

Proposed EPA emission regulations require emission reduction by 1979 for various gas turbine engine classes. Extensive combustion technology advancements are required to meet the proposed regulations. The T56 turboprop engine requires CO, UHC, and smoke reduction. A staged fuel combustor design was tested on a combustion rig to evaluate emission reduction potential in turboprop engines from fuel zoning. The can-type combustor has separately fueled-pilot and main combustion zones in series. The main zone fueling system was arranged for potential incorporation into the T56 with minor or no modifications to the basic engine. Three combustor variable geometry systems were incorporated to evaluate various airflow distributions. Emission results with fixed geometry operation met all proposed EPA regulations over the EPA LTO cycle. CO reduction was 82 percent, UHC reduction was 96 percent, and smoke reduction was 84 percent. NOx increased 14 percent over the LTO cycle. At high power, NOx reduction was 40 to 55 percent. This NOx reduction has potential application to stationary gas turbine powerplants which have different EPA regulations.

Verdouw, A. J.↗
NASA NTRS1977

A review of advanced rotor research

This paper reviews advanced-rotor concepts including the advancing blade concept, the circulation control rotor, the X-wing rotor, the variable diameter rotor, the hingeless tilt rotor, the bearingless main rotor, the composite structures rotor, the variable geometry rotor, the multicyclic controllable pitch rotor, the multicyclic controllable twist rotor, and the live twist rotor. The rotor concepts are discussed in terms of performance (cruise speed, and lift/drag ratio) and dynamic loads and vibration.

Kelly, M. W.↗
NASA NTRS1977

Advanced supersonic propulsion study, phase 4

Installation characteristics for a Variable Stream Control Engine (VSCE) were studied for three advanced supersonic airplane designs. Sensitivity of the VSCE concept to change in technology projections was evaluated in terms of impact on overall installed performance. Based on these sensitivity results, critical technology requirements were reviewed, resulting in the reaffirmation of the following requirements: low-noise nozzle system; a high performance, low emissions duct burner and main burner; hot section technology; variable geometry components; and propulsion integration features, including an integrated electronic control system.

Howlett, R. A.↗
NASA NTRS1977

Performance of twin two-dimensional wedge nozzles including thrust vectoring and reversing effects at speeds up to Mach 2.20

Transonic tunnel and supersonic pressure tunnel tests were reformed to determine the performance characteristics of twin nonaxisymmetric or two-dimensional nozzles with fixed shrouds and variable-geometry wedges. The effects of thrust vectoring, reversing, and installation of various tails were also studied. The investigation was conducted statically and at flight speeds up to a Mach number of 2.20. The total pressure ratio of the simulated jet exhaust was varied up to approximately 26 depending on Mach number. The Reynolds number per meter varied up to 13.20 x 1 million. An analytical study was made to determine the effect on calculated wave drag by varying the mathematical model used to simulate nozzle jet-exhaust plume.

Capone, F. J.↗
NASA NTRS1977

ENGINEL: A single rotor turbojet engine cycle match performance program

ENGINEL is a computer program which was developed to generate the design and off-design performance of a single rotor turbojet engine with or without afterburning using a cycle match procedure. It is capable of producing engine performance over a wide range of altitudes and Mach numbers. The flexibility, of operating with a variable geometry turbine, for improved off-design fuel consumption or with a fixed geometry turbine as in conventional turbojets, has been incorporated. In addition, the option of generation engine performance with JP4, liquid hydrogen or methane as fuel is provided.

Lovell, W. A.↗
NASA NTRS1978

Automotive gas turbine fuel control

A fuel control system is reported for automotive-type gas turbines and particulary advanced gas turbines utilizing variable geometry components to improve mileage and reduce pollution emission. The fuel control system compensates for fuel density variations, inlet temperature variations, turbine vane actuation, acceleration, and turbine braking. These parameters are utilized to control various orifices, spool valves and pistons.

Gold, H.↗