Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “transition path”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Development of Complexity Science and Technology Tools for NextGen Airspace Research and Applications

The objective of this research by NextGen AeroSciences, LLC is twofold: 1) to deliver an initial "toolbox" of algorithms, agent-based structures, and method descriptions for introducing trajectory agency as a methodology for simulating and analyzing airspace states, including bulk properties of large numbers of heterogeneous 4D aircraft trajectories in a test airspace -- while maintaining or increasing system safety; and 2) to use these tools in a test airspace to identify possible phase transition structure to predict when an airspace will approach the limits of its capacity. These 4D trajectories continuously replan their paths in the presence of noise and uncertainty while optimizing performance measures and performing conflict detection and resolution. In this approach, trajectories are represented as extended objects endowed with pseudopotential, maintaining time and fuel-efficient paths by bending just enough to accommodate separation while remaining inside of performance envelopes. This trajectory-centric approach differs from previous aircraft-centric distributed approaches to deconfliction. The results of this project are the following: 1) we delivered a toolbox of algorithms, agent-based structures and method descriptions as pseudocode; and 2) we corroborated the existence of phase transition structure in simulation with the addition of "early warning" detected prior to "full" airspace. This research suggests that airspace "fullness" can be anticipated and remedied before the airspace becomes unsafe.

Holmes, Bruce J.↗
NASA NTRS2011

Real-Time Deposition Monitor for Ultrathin Conductive Films

A device has been developed that can be used for the real-time monitoring of ultrathin (2 or more) conductive films. The device responds in less than two microseconds, and can be used to monitor film depositions up to about 60 thick. Actual thickness monitoring capability will vary based on properties of the film being deposited. This is a single-use device, which, due to the very low device cost, can be disposable. Conventional quartz/crystal microbalance devices have proven inadequate to monitor the thickness of Pd films during deposition of ultrathin films for hydrogen sensor devices. When the deposited film is less than 100 , the QCM measurements are inadequate to allow monitoring of the ultrathin films being developed. Thus, an improved, high-sensitivity, real-time deposition monitor was needed to continue Pd film deposition development. The new deposition monitor utilizes a surface acoustic wave (SAW) device in a differential delay-line configuration to produce both a reference response and a response for the portion of the device on which the film is being deposited. Both responses are monitored simultaneously during deposition. The reference response remains unchanged, while the attenuation of the sensing path (where the film is being deposited) varies as the film thickness increases. This device utilizes the fact that on high-coupling piezoelectric substrates, the attenuation of an SAW undergoes a transition from low to very high, and back to low as the conductivity of a film on the device surface goes from nonconductive to highly conductive. Thus, the sensing path response starts with a low insertion loss, and as a conductive film is deposited, the film conductivity increases, causing the device insertion loss to increase dramatically (by up to 80 dB or more), and then with continued film thickness increases (and the corresponding conductivity increases), the device insertion loss goes back down to the low level at which it started. This provides a continuous, real-time monitoring of film deposition. For use with different films, the device would need to be calibrated to provide an understanding of how film thickness is related to film conductivity, as the device is responding primarily to conductivity effects (and not to mass loading effects) in this ultrathin film regime.

Hines, Jacqueline↗
NASA NTRS2017

Shape Memory Actuated Normally Open Permanent Isolation Valve

A valve assembly for an in-space propulsion system includes an inlet tube, an outlet tube, a valve body coupling the inlet tube to the outlet tube and defining a propellant flow path, a valve stem assembly disposed within the valve body, an actuator body coupled to the valve body, the valve stem assembly extending from an interior of the valve body to an interior of the actuator body, and an actuator assembly disposed within the actuator body and coupled to the valve stem assembly, the actuator assembly including a shape memory actuator member that when heated to a transition temperature is configured to enable the valve stem assembly to engage the outlet tube and seal the propellant flow path.

Ramspacher, Daniel J.↗
NASA NTRS2020

Observation of Strong Two-Electron-One-Photon Transitions in Few-Electron Ions

We resonantly excite the K series of O5+ and O6+ up to principal quantum number n = 11 with monochromatic x rays, producing K-shell holes, and observe their relaxation by soft-x-ray emission. Some photoabsorption resonances of O5+ reveal strong two-electron–one-photon (TEOP) transitions. We find that for the [(1s2s)15p3/2]3/2;1/2 states, TEOP relaxation is by far stronger than the radiative decay and competes with the usually much faster Auger decay path. This enhanced TEOP decay arises from a strong correlation with the near-degenerate upper states [(1s2p3/2 )14s]3/2;1/2 of a Li-like satellite blend of the He-like Kα transition. Even in three-electron systems, TEOP transitions can play a dominant role, and the present results should guide further research on the ubiquitous and abundant many-electron ions where electronic energy degeneracies are far more common and configuration mixing is stronger.

M Togawa↗
NASA NTRS1975

Space vehicle Viterbi decoder

The design and fabrication of an extremely low-power, constraint-length 7, rate 1/3 Viterbi decoder brassboard capable of operating at information rates of up to 100 kb/s is presented. The brassboard is partitioned to facilitate a later transition to an LSI version requiring even less power. The effect of soft-decision thresholds, path memory lengths, and output selection algorithms on the bit error rate is evaluated. A branch synchronization algorithm is compared with a more conventional approach. The implementation of the decoder and its test set (including all-digital noise source) are described along with the results of various system tests and evaluations. Results and recommendations are presented.

Source record↗
NASA NTRS1982

Meteorological effects on laser propagation for power transmission

An examination of possible laser operating parameters for power transmission to earth from solar power satellites is presented, with particular attention paid to assuring optimal delivery at midlatitudes. The degradation of beam efficiency due to molecular scattering, molecular absorption, aerosol scattering, and aerosol absorption during beam propagation through the atmosphere can be alleviated by judicious choice of wavelength windows, elevating the receptor sites, using a vertical propagation path, or by hole boring, i.e., vaporizing the aerosol particles in the beam path. Analyses are given for the beam propagation through fog, haze, clouds, and snow using various transitions. Only weapons-quality lasers are seen as being capable of boring through clouds and aerosols, employing a CW beam with superimposed pulses at high power densities. It is concluded that further short wavelength transmission experiments be performed to demonstrate transmission feasibility with the CW/pulsed mode of beam propagation.

Beverly, R. E., III↗
NASA NTRS1959

A Concept of a Manned Satellite Reentry Which is Completed with a Glide Landing

A concept for a manned satellite reentry from a near space orbit and a glide landing on a normal size airfield is presented. The reentry vehicle configuration suitable for this concept would employ a variable geometry feature in order that the reentry could be made at 90 deg. angle of attack and the landing could be made with a conventional glide approach. Calculated results for reentry at a flight-path angle of -1 deg. show that with an accuracy of 1 percent in the impulse of a retrorocket, the desired flight-path angle at reentry can be controlled within 0.02 deg. and the distance traveled to the reentry point, within 100 miles. The reentry point is arbitrarily defined as the point at which the satellite passes through an altitude of about 70 miles. Misalignment of the retrorocket by 10 deg. increased these errors by as much as 0.02 deg. and 500 miles. Intra-atmospheric trajectory calculations show that pure drag reentries starting with flight-path angles of -1 deg. or less produce a peak deceleration of 8g. Lift created by varying the angle of attack between 90 and 60 deg. is effective in decreasing the maximum deceleration and allows the range to the "recovery" point (where transition is made from reentry to gliding flight) to be increased by as much as 2,300 miles. A sideslip angle of 30 deg. allows lateral displacement of the flight path by as much as 60 deg. miles. Reaction controls would provide control-attitude alignment during the orbit phase. For the reentry phase this configuration should have low static longitudinal and roll stability in the 90 deg. angle-of-attack attitude. Control could be effected by leading-edge and trailing-edge flaps. Transition into the landing phase would be accomplished at an altitude of about 100,000 feet by unfolding the outer wing panels and pitching over to low angles of attack. Calculations indicate that glides can be made from the recovery point to airfields at ranges of from 150 to 200 miles, depending upon the orientation with respect to the original course.

Cheatham, Donald C.↗
NASA NTRS1993

Progress towards understanding and predicting heat transfer in the turbine gas path

A new era is dawning in the ability to predict convection heat transfer in the turbine gas path. We feel that the technical community now has the capability to mount a major assault on this problem, which has eluded significant progress for a long time. In this paper we hope to make a case for this bold statement by reviewing the state of the art in three major and related areas, which we believe are indispensable to the understanding and accurate prediction of turbine gas path heat transfer: configuration-specific experiments, fundamental physics and model development, and code development. We begin our review with the configuration-specific experiments, whose data have provided the big picture and guided both the fundamental modeling research and the code development. Following that, we examine key modeling efforts and comment on what will be needed to incorporate them into the codes. In this region we concentrate on bypass transition, 3D endwalls, and film cooling. We then review progress and directions in the development of computer codes to predict turbine gas path heat transfer. Finally, we cite examples and make observations on the more recent efforts to do all this work in a simultaneous, interactive, and more synergistic manner. We conclude with an assessment of progress, suggestions for how to use the current state of the art, and recommendations for the future.

Simoneau, Robert J.↗
NASA NTRS2003

Transition in Hypersonic Flows Including High-temperature Gas Effects

Hypersonic transition poses a special challenge for direct numerical simulations. Comparable data from Wind-tunnel tests or free-flight testing are not available or not accurate enough for comparison. The wind-tunnel testing does not allow for the exact match to the free-flight conditions at such high Mach-numbers. Flat-plate boundary-layer transition at high Mach-numbers is investigated in this work. A simulation case was chosen where chemical non-equilibrium plays an important role but ionization can be neglected. The chosen case at an altitude of H=50Km lies close to one point on the descent path of the Space Shuttle. The failure of the Space Shuttle has shown that an improved vehicle for space transportation is imperative in the close future. Transition research for an improved space-transportation vehicle is crucial in order to estimate the heat load during re-entry.

Stemmer, Christian↗
NASA NTRS1975

Vibration-translation energy transfer in anharmonic diatomic molecules. I - A comparative evaluation of the semiclassical approximation

The semiclassical approximation (quantum oscillator, classical path) is applied to anharmonic diatomic oscillators in excited initial states. Multistate numerical solutions giving the vibrational transition probabilities for collinear collisions with an inert atom are compared with equivalent, exact quantum-mechanical calculations. Several symmetrization methods are shown to correlate accurately the predictions of both theories for all initial states, transitions, and molecular types tested, but only if coupling of the oscillator motion and the classical trajectory of the incident particle is considered. In anharmonic heteronuclear molecules, the customary semiclassical method of computing the classical trajectory independently leads to transition probabilities with anomalous low-energy resonances. Proper accounting of the effects of oscillator compression and recoil on the incident particle trajectory removes the anomalies and restores the applicability of the semiclassical approximation.

Mckenzie, R. L.↗
NASA NTRS1993

A study of electron transfer using a three-level system coupled to an ohmic bath

Electron transfer is studied using a multi-level system coupled to a bosonic bath. Two body correlation functions are obtained using both exact enumeration of spin paths and Monte Carlo simulation. It was found that the phase boundary for the coherent-incoherent transition lies at a smaller friction in the asymmetric two-level model than in the symmetric two-level model. A similar coherent-incoherent transition is observed for three-level system.

Takasu, Masako↗
NASA NTRS1999

Tracks to therapy

Studies of the structure of particle tracks have led to models of track effects based on radial dose and radiobiological target theory that have been very successful in describing and predicting track effects in physical, chemical, and biological systems. For describing mammalian cellular inactivation two inactivation modes are required, called gamma-kill and ion-kill, the first due to synergistic effects of delta rays from adjacent ion paths thus resembling the effects from gamma rays, and the second to the effects of single ion transits through a cell nucleus. The ion-kill effect is more severe, where the fraction of cells experiencing ion kill is responsible for a decrease in the oxygen enhancement ratio, and an increase in relative biological effectiveness, but these are accompanied by loss of repair, hence to a reduction in the efficiency of fractionation in high LET therapy, as shown by our calculations for radiobiological effects in the "spread out Bragg Peak".

Review, Tutorial↗
NASA NTRS2020

Mid-infrared detector development for the Origins Space Telescope

Mid-infrared detector arrays operating from 2.8 to 20 μm are baselined in the design of the Origins Space Telescope Mid-Infrared Spectrometer Instrument. This instrument is designed to detect and measure the spectral signatures of gases of biogenic origin in the atmospheres of exoplanets as they transit their host stars. In order to make these detections, the detector array’s pixels need to have high-signal stability when exposed to a constant flux in multiple time-series integration over a typical transit time of a few hours. With the use of a densified pupil spectrometer design, pointing effects can be mitigated because pointing variations do not displace spectra on the detector and each wavelength of light is averaged over a large number of pixels, giving good spectrophotometric stabilities. The current state-of-the-art detector arrays do not achieve these stabilities, although with a feasible development program this level of performance should be achievable. Three detector technologies are under consideration for this development, HgCdTe arrays, Si:As impurity band conduction arrays, and transition edge super-conductor bolometer arrays. We primarily treat the HgCdTe technology development, but also introduce the paths forward for the other two technologies. After a few years-long investigative programs, a down-select will be undertaken to select the flight technology.

Astronomy↗
NASA NTRS1993

Applicability of PM3 to transphosphorylation reaction path: Toward designing a minimal ribozyme

A growing body of evidence shows that RNA can catalyze many of the reactions necessary both for replication of genetic material and the possible transition into the modern protein-based world. However, contemporary ribozymes are too large to have self-assembled from a prebiotic oligonucleotide pool. Still, it is likely that the major features of the earliest ribozymes have been preserved as molecular fossils in the catalytic RNA of today. Therefore, the search for a minimal ribozyme has been aimed at finding the necessary structural features of a modern ribozyme (Beaudry and Joyce, 1990). Both a three-dimensional model and quantum chemical calculations are required to quantitatively determine the effects of structural features of the ribozyme on the reaction it catalyzes. Using this model, quantum chemical calculations must be performed to determine quantitatively the effects of structural features on catalysis. Previous studies of the reaction path have been conducted at the ab initio level, but these methods are limited to small models due to enormous computational requirements. Semiempirical methods have been applied to large systems in the past; however, the accuracy of these methods depends largely on a simple model of the ribozyme-catalyzed reaction, or hydrolysis of phosphoric acid. We find that the results are qualitatively similar to ab initio results using large basis sets. Therefore, PM3 is suitable for studying the reaction path of the ribozyme-catalyzed reaction.

Manchester, John I.↗
NASA NTRSDate not supplied

Geometric Acoustics for Aircraft Noise Scattering

This paper discusses aircraft noise scattering by geometric acoustics, which consists of the basic features of sound propagation and reflection in rays or ray tubes, diffraction by smooth geometry in terms of surface creeping waves, and diffraction by abrupt geometry features such as the wing trailing edges. Based on the classic theories of these features, prediction methodologies can be constructed for aircraft noise scattering. The methodologies, however, require important modifications and extensions to account for unique features in aircraft noise applications, for both current conventional aircraft and future unconventional designs. These modifications and extensions include the derivation of a general reflection coefficient that contains the effects of surface geometry curvature, surface impedance, and mean flow. Corrections to the basic formulation of diffraction, both smooth geometry and sharp edges, are formulated to account for the finite dimensions of practical applications. For smooth geometry diffraction, a second order correction is used to continuously transition from insolified to shadow zones and an approach is presented to compute the properties of the geodesic path of surface wave propagation. A model is developed to make use of the ray propagation formulation for incoherent and partially coherent propagation and scattering, which is an important phenomenon in aircraft noise. Mean flow effect is also included in the methodology for low Mach number flows. Examples of calculations based on these theoretical developments are presented to illustrate the unique features in aircraft noise applications.

Yueping Guo↗
NASA NTRS2015

In-Space Manufacturing: Pioneering a Sustainable Path to Mars

ISM is responsible for developing the on-demand manufacturing capabilities that will be required for affordable, sustainable operations during Exploration Missions (in-transit and on-surface) to destinations such as Mars. This includes advancing the needed technologies, as well as establishing the skills & processes (such as certification and characterization) that will enable the technologies to go from novel to institutionalized. These technologies are evolving rapidly due to terrestrial markets. ISM is leveraging this commercial development to develop these capabilities within a realistic timeframe and budget. ISM utilizes the International Space Station (ISS) as a test-bed to adapt these technologies for microgravity operations and evolve the current operations mindset from earth-reliant to earth-independent.

Werkheiser, Niki↗
NASA NTRS2006

The Airspace Concepts Evaluation System Architecture and System Plant

The Airspace Concepts Evaluation System is a simulation of the National Airspace System. It includes models of flights, airports, airspaces, air traffic controls, traffic flow managements, and airline operation centers operating throughout the United States. It is used to predict system delays in response to future capacity and demand scenarios and perform benefits assessments of current and future airspace technologies and operational concepts. Facilitation of these studies requires that the simulation architecture supports plug and play of different air traffic control, traffic flow management, and airline operation center models and multi-fidelity modeling of flights, airports, and airspaces. The simulation is divided into two parts that are named, borrowing from classical control theory terminology, control and plant. The control consists of air traffic control, traffic flow management, and airline operation center models, and the plant consists of flight, airport, and airspace models. The plant can run open loop, in the absence of the control. However, undesired affects, such as conflicts and over congestions in the airspaces and airports, can occur. Different controls are applied, "plug and played", to the plant. A particular control is evaluated by analyzing how well it managed conflicts and congestions. Furthermore, the terminal area plants consist of models of airports and terminal airspaces. Each model consists of a set of nodes and links which are connected by the user to form a network. Nodes model runways, fixes, taxi intersections, gates, and/or other points of interest, and links model taxiways, departure paths, and arrival paths. Metering, flow distribution, and sequencing functions can be applied at nodes. Different fidelity model of how a flight transits are can be used by links. The fidelity of the model can be adjusted by the user by either changing the complexity of the node/link network-or the way that the link models how the flights transit from one node to the other.

Windhorst, Robert↗