SEARCH · Engineering Papers

Results for “textured surfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Attempt of Serendipitous Science During the Mojave Volatile Prospector Field Expedition

On 23 October a partial solar eclipse occurred across parts of the southwest United States between approximately 21:09 and 23:40 (UT), with maximum obscuration, 36%, occurring at 22:29 (UT). During 21-26 October 2014 the Mojave Volatile Prospector (MVP) field expedition deployed and operated the NASA Ames Krex2 rover in the Mojave desert west of Baker, California (Fig. 1, bottom). The MVP field expedition primary goal was to characterize the surface and sub-surface soil moisture properties within desert alluvial fans, and as a secondary goal to provide mission operations simulations of the Resource Prospector (RP) mission to a Lunar pole. The partial solar eclipse provided an opportunity during MVP operations to address serendipitous science. Science instruments on Krex2 included a neutron spectrometer, a near-infrared spectrometer with associated imaging camera, and an independent camera coupled with software to characterize the surface textures of the areas encountered. All of these devices are focused upon the surface and as a result are downward looking. In addition to these science instruments, two hazard cameras are mounted on Krex2. The chief device used to monitor the partial solar eclipse was the engineering development unit of the Near-Infrared Volatile Spectrometer System (NIRVSS) near-infrared spectrometer. This device uses two separate fiber optic fed Hadamard transform spectrometers. The short-wave and long-wave spectrometers measure the 1600-2400 and 2300-3400 nm wavelength regions with resolutions of 10 and 13 nm, respectively. Data are obtained approximately every 8 seconds. The NIRVSS stares in the opposite direction as the front Krex2.

soil moisture properties↗

NASA NTRS2015

Predicting Clear-Sky Reflectance Over Snow/Ice in Polar Regions

Satellite remote sensing of clouds requires an accurate estimate of the clear-sky radiances for a given scene to detect clouds and aerosols and to retrieve their microphysical properties. Knowing the spatial and angular variability of clear-sky albedo is essential for predicting clear-sky radiance at solar wavelengths. The Clouds and the Earth's Radiant Energy System (CERES) Project uses the nearinfrared (NIR; 1.24, 1.6 or 2.13 micrometers), visible (VIS; 0.63 micrometers) and vegetation (VEG; 0.86 micrometers) channels available on the Terra and Aqua Moderate Resolution Imaging Spectroradiometer (MODIS) to help identify clouds and retrieve their properties in both snow-free and snow-covered conditions. Thus, it is critical to have reliable distributions of clear-sky albedo for all of these channels. In CERES Edition 4 (Ed4), the 1.24-micrometer channel is used to retrieve cloud optical depth over snow/ice-covered surfaces. Thus, it is especially critical to accurately predict the 1.24-micrometer clear-sky albedo alpha and reflectance rho for a given location and time. Snow albedo and reflectance patterns are very complex due to surface texture, particle shapes and sizes, melt water, and vegetation protrusions from the snow surface. To minimize those effects, this study focuses on the permanent snow cover of Antarctica where vegetation is absent and melt water is minimal. Clear-sky albedos are determined as a function of solar zenith angle (SZA) from observations over all scenes determined to be cloud-free to produce a normalized directional albedo model (DRM). The DRM is used to develop alpha(SZA=0 degrees) on 10 foot grid for each season. These values provide the basis for predicting r at any location and set of viewing & illumination conditions. This paper examines the accuracy of this approach for two theoretical snow surface reflectance models.

Chen, Yan↗

NASA NTRS1967

Skidding accidents on runways and highways can be reduced.

Skidding accident reduction investigated for runway and highway safety noting worn tires, smooth surface texture, locked wheels and pilot technique

SURFACE ROUGHNESS↗

NASA NTRS1989

Roughening Surfaces Of Solar Cells

Proposed treatment involving bombardment by ions gives silicon solar cells rough surfaces and increases amount of light absorbed by cells. First step of treatment, wafer of single-crystal silicon held at temperature of 70 degree C or higher while bombarded with argon or hydrogen ions at kinetic energies between 100 and 2,000 eV. This high dose produces damaged layer on surface, consisting of outer polycrystalline sublayer and underlying sublayer containing extended defects. Bombarded wafer then etched chemically. Photovoltaic conversion efficiency increases with number of reflections at surface of silicon cell because large part of light absorbed at each reflection. Deeply textured surface provides opportunities for multiple reflections.

Singh, Ranbir↗

NASA NTRS1973

Imaging radars provide terrain texture and roughness parameters in semi-arid environments

Geoscience potentialities and limitations of available imaging radars are examined for alluvial valley-playa terrain environments. In such arid environments, a dual-sensor combination of an imaging radar with aerial photography is shown to provide a practical method for monitoring gross changes in surface textures of alluvial fans and playa surface conditions. It also appears feasible to infer surface materials and relative surface roughness with an improved degree of interpretive reliability.

Macdonald, H. C.↗

NASA NTRS1977

Geological Observations in the Cydonia Region of Mars from Viking

During the Viking mission, three broad areas of the northern plains were investigated as possible landing sites for Viking lander 2. We present a geological map of the area designated the B1 landing site in Cydonia centered on 45 deg N latitude, 4 deg W longitude. Viking imagery of this area has given detailed coverage, allowing the northern plains to be examined in more detail over wider areas than was possible from Mariner 9. Some plains areas with polygonal fracture patterns are considered to be pediments in ancient southern hemisphere rocks. The fracture patterns predate at least some of the younger northern plains material. Several northern plains units are distinguished as well as surface textures of unknown origin. Viking pictures provide good data for future studies of stratigraphy and surface process in this region and others like it in northern latitudes.

Guest, J. E.↗

NASA NTRS1980

Ion-beam etching enhances adhesive bonding

Metals and fluoropolymers exposed to 0.5 to 1.0 keV argon ions at current densities of 0.2 to 1.5 mA/sq cm develop surface texturing that increases tensile and shear strength of epoxy bonds. Bonds are 46 to 100 percent stronger than those of chemically etched surfaces. Metals require 3 to 4 hours of bombardment to become properly textured. Fluoropolymers require 5 seconds to 30 minutes. Ion beam will not texture nickel. Unlike chemical treatments, bonding of fluoropolymers can be done days or months after ion treatment.

Banks, B. A.↗

NASA NTRS2012

Implications of Adhesion Studies for Dust Mitigation on Thermal Control Surfaces

Experiments measuring the adhesion forces under ultrahigh vacuum conditions (10 (exp -10) torr) between a synthetic volcanic glass and commonly used space exploration materials have recently been described. The glass has a chemistry and surface structure typical of the lunar regolith. It was found that Van der Waals forces between the glass and common spacecraft materials was negligible. Charge transfer between the materials was induced by mechanically striking the spacecraft material pin against the glass plate. No measurable adhesion occurred when striking the highly conducting materials, however, on striking insulating dielectric materials the adhesion increased dramatically. This indicates that electrostatic forces dominate over Van der Waals forces under these conditions. The presence of small amounts of surface contaminants was found to lower adhesive forces by at least two orders of magnitude, and perhaps more. Both particle and space exploration material surfaces will be cleaned by the interaction with the solar wind and other energetic processes and stay clean because of the extremely high vacuum (10 (exp -12) torr) so the atomically clean adhesion values are probably the relevant ones for the lunar surface environment. These results are used to interpret the results of dust mitigation technology experiments utilizing textured surfaces, work function matching surfaces and brushing. They have also been used to reinterpret the results of the Apollo 14 Thermal Degradation Samples experiment.

Gaier, James R.↗

NASA NTRS1996

Texture Modification of the Shuttle Landing Facility Runway at the NASA Kennedy Space Center

This paper describes the test procedures and the selection criteria used in selecting the best runway surface texture modification at the Kennedy Space Center (KSC) Shuttle Landing Facility (SLF) to reduce Orbiter tire wear. The new runway surface may ultimately result in an increase of allowable crosswinds for launch and landing operations. The modification allows launch and landing operations in 20-kt crosswinds if desired. This 5-kt increase over the previous 15-kt limit drastically increases landing safety and the ability to make on-time launches to support missions where space station rendezvous is planned.

Daugherty, Robert H.↗

NASA NTRS1979

Colorimetry and magnitudes of asteroids

In the present paper, 1500 UBV observations are analyzed by a new rather general multiple scattering theory which provided clear insight into previously poorly-recognized optical nature of asteroid surfaces. Thus, phase curves are shown to consist of a surface-texture controlled component, due to singly scattered light, and a component due to multiple scattering. Phase curve shapes can be characterized by a single parameter, the multiple scattering factor, Q. As Q increases, the relative importance of the opposition effect diminishes. Asteroid surfaces are particulate and strikingly similar to texture, being moderately porous and moderately rough on a scale greater than the wavelength of light. In concequence, Q (and also the phase coefficient) correlate well with geometric albedo, and there exists a purely photometric means of determining albedos and diameters.

Bowell, E.↗

NASA NTRS1974

Mapping soil features from multispectral scanner data

In being able to identify quickly gross variations in soil features, the computer-aided classification of multispectral scanner data can be an effective aid to soil surveying. Variations in soil tone are easily seen as well as variations in features related to soil tone, e.g., drainage patterns and organic matter content. Changes in surface texture also affect the reflectance properties of soils. Inasmuch as conventional soil classes are based on both surface and subsurface soil characteristics, the technique described here can be expected only to augment and not replace traditional soil mapping.

Kristof, S. J.↗

NASA NTRS1984

Ion-beam-textured and coated surfaces experiment (S1003)

The objective of this LDEF experiment is to measure the effects of exposure to the shuttle launch and near Earth space environments on the optical properties of ion beam textured high absorptance solar thermal control surfaces, the optical and electrical properties of ion beam sputtered conductive solar thermal control surfaces, and the weight loss of ion beam deposited oxide polymer films. The various types of surfaces to be tested include six major categories: (1) ion beam textured surfaces suitable for space solar thermal (solar concentration) application; (2) painted and/or state of the art solar thermal surfaces; (3) ion beam sputtered conductive coatings for thermal and space charge control (e.g., indium-oxide coated metalized FEP Teflon); (4) ion beam sputtered conductive coated solar sail materials for space charge control and cooling through emittance; (5) micrometeoroid sensitive samples whose optical properties change only as a result of micrometeoroid impact; and (6) Kapton coated with oxide polymer films to minimize oxygen degradation at near Earth orbit altitudes.

Mirtich, M. J., Jr.↗

DOE OSTI2021

Analysis of convection heat transfer on multiscale rough superhydrophobic and liquid infused surfaces

Multiscale rough superhydrophobic or slippery liquid infused porous surfaces have gained much interest in recent years for their improved transport phenomena properties. While there have been several studies on drag reduction and condensation on non-wetting surfaces, convection heat transfer that is important in many thermal and thermochemical applications has not been addressed systematically. Here, this article utilizes a fractal description of rough surface topographies to develop analytical models for the Nusselt number and the thermal hydraulic factor for fluid flow and heat transfer inside a cylinder with non-wetting surfaces. For air-infused superhydrophobic surfaces, the model considers the dynamic stability of the air/fluid interface in the asperities. Using the analytical formulations and the stability criteria, systematic studies are presented on the effects of the fractal surface parameters, cylinder radius and Reynolds number on the convective heat transfer characteristics, from which surface texture design maps are developed for maximizing the convection heat transfer. It is shown that multiscale non-wetting surfaces are most effective in the range of lower Reynolds number and small cylinder radius for achieving the best convective heat transfer and thermal hydraulic performance. Applying the models to actual non-wetting surface topographies fabricated using electrodeposition and chemical etching, it is shown that contrary to prevailing notion, superhydrophobicity, characterized by the highest contact angles, does not always lead to the maximum convective heat transfer performance, and that under certain fluid flow conditions, hydrophobic surfaces may offer a greater thermal performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1977

Plastic (wire-combed) grooving of a slip-formed concrete runway overlay at Patrick Henry Airport: An initial evaluation

A wire-comb technique is described for transversely grooving the surface of a freshly laid (plastic state) slip-formed concrete overlay installed at Patrick Henry Airport. This method of surface texturing yields better water drainage and pavement skid resistance than that obtained with an older conventional burlap drag concrete surface treatment installed on an adjacent portion of the runway.

Marlin, E. C.↗

NASA NTRS1976

Potential biomedical applications of ion beam technology

Electron bombardment ion thrusters used as ion sources have demonstrated a unique capability to vary the surface morphology of surgical implant materials. The microscopically rough surface texture produced by ion beam sputtering of these materials may result in improvements in the biological response and/or performance of implanted devices. Control of surface roughness may result in improved attachment of the implant to soft tissue, hard tissue, bone cement, or components deposited from blood. Potential biomedical applications of ion beam texturing discussed include: vascular prostheses, artificial heart pump diaphragms, pacemaker fixation, percutaneous connectors, orthopedic pros-thesis fixtion, and dental implants.

Banks, B. A.↗

NASA NTRS1976

Potential biomedical applications of ion beam technology

Banks, B. A.↗

NASA NTRS1991

Results of examination of silvered Teflon from the Long Duration Exposure Facility

Pieces of silvered Teflon thermal control blanket from seventeen locations on the Long Duration Exposure Facility (LDEF) were studied. Results of the measurements of surface texturing, and mechanical, electrical and thermal properties are presented. Photos of the blankets, scanning electron microscope pictures, infrared spectra, and surface analysis results are presented. Contamination issues relative to performance of the blankets are discussed. The variation in measured properties are reported as a function of exposure conditions.

Rousslang, Ken W.↗

NASA NTRS2003

Production of Near-Mirror Surface Quality by Precision Grinding

Mechanical components such as gears and bearings operate with the working surfaces in intimate contact with a mating part. The performance of such components will be influenced by the quality of the working surface. In general, a smoother surface will perform better than a rougher surface since the lubrication conditions are improved. For example, surfaces with a special near-mirror quality finish of low roughness performed better than ground surfaces when tested using a block-on-ring arrangement. Bearings with near-mirror quality have been tested and analyzed; lower running torques were measured and improved fatigue life was anticipated. Experiments have been done to evaluate the performance of gears with improved, low roughness surface finishing. The measured performance improvements include an increased scuffing (scoring) load capacity by a factor of 1.6, a 30-percent reduction of gear tooth running friction, and longer fatigue lives by a factor of about four. One can also anticipate that near-mirror quality surface finishing could improve the performance of other mechanical components such as mechanical seals and heavily loaded journal bearings. Given these demonstrated benefits, capable and economical methods for the production of mechanical components with near-mirror quality surfaces are desired. One could propose the production of near-mirror quality surfaces by several methods such as abrasive polishing, chemical assisted polishing, or grinding. Production of the surfaces by grinding offers the possibility to control the macro-geometry (form), waviness, and surface texture with one process. The present study was carried out to investigate the possibility of producing near-mirror quality surfaces by grinding. The present study makes use of a specially designed grinding machine spindle to improve the surface quality relative to the quality produced when using a spindle of conventional design.

Dimofte, Florin↗