Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “substrate channeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

High figure of merit extreme bandgap Al 0.87 Ga 0.13 N-Al 0.64 Ga 0.36 N heterostructures over bulk AlN substrates

We report on high-quality n -Al 0.87 Ga 0.13 N-A 0.64 Ga 0.36 N heterostructures over single crystal AlN. For these pseudomorphic heterostructures, high-resolution X-ray and X-ray Topographic analysis was used to establish a threading dislocation density of 7 × 10 3 cm -2 . Using reverse composition graded n + -Al x Ga 1- x N contact layers, we obtained linear ohmic contacts with 4.3 Ω mm specific resistance. A critical breakdown field >11 MV cm -1 was also measured. In combination with the channel resistance of 2400 Ω sq -1 , these translate to a Baliga’s Figure of Merit of 2.27 GW cm -2 . This, to the best of our knowledge is the highest reported value for extreme bandgap AlGaN heterostructures.

42 ENGINEERING↗
DOE OSTI2020

Fabrication of a composite anion exchange membrane with aligned ion channels for a high-performance non-aqueous vanadium redox flow battery

Fabrication of high-conductivity ion exchange membranes (IEMs) is crucial to improve the performance of non-aqueous vanadium redox flow batteries (NAVRFBs). In the present work, anion exchange membranes with high-conductivity were fabricated by aligning ion channels of the polymer electrolyte impregnated in porous polytetrafluoroethylene (PTFE) under electric fields. It was observed that the ion channels of the polymer electrolyte were uniformly orientated in the atomic-force microscopy image. Its morphological change could minimize detouring of the transport of BF 4 - ions. The results showed through-plane conductivity was improved from 12.7 to 33.1 mS cm -1 . The dimensional properties of the fabricated membranes were also enhanced compared with its cast membrane owing to the reinforcing effect of the substrate. Especially, the NAVRFB assembled with the optimized membrane showed increased capacities, with a 97% coulombic efficiency and 70% energy efficiency at 80 mA cm -2 . Furthermore, the optimized membrane made it possible to operate the NAVRFB at 120 mA cm -2 . Its operating current density was 120 times higher than that of a frequently used AHA membrane for RFBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Ablating nanoscale pores in crystalline quartz using laser-induced micro-plasmas in tri-layer structures

We demonstrate a novel approach for achieving rapid, consistent, and controllable micro-pore fabrication in single-crystalline quartz. These micro-pores are essential for applications in biology, i.e., studying ion channels in general and mechano-sensitive channels (MSC) in particular. The fabrication process consists of direct material ablation using pulsed UV light from a 193 nm excimer laser. These pulses ablate single-crystalline quartz chips by burning a laser-induced plasma in a tri-layer structure. Controllable plasma confinement and thus pore size is achieved by sandwiching a thin layer of a selected organic solution between the quartz chip and different substrates. This solution causes the confined micro-plasma to generate special ablation conditions, to create uniformly sized and shaped nanopores.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Pharmacological Profiling of a Brugia malayi Muscarinic Acetylcholine Receptor as a Putative Antiparasitic Target

The diversification of anthelmintic targets and mechanisms of action will help ensure the sustainable control of nematode infections in response to the growing threat of drug resistance. G protein-coupled receptors (GPCRs) are established drug targets in human medicine but remain unexploited as anthelmintic substrates despite their important roles in nematode neuromuscular and physiological processes. Bottlenecks in exploring the druggability of parasitic nematode GPCRs include a limited helminth genetic toolkit and difficulties establishing functional heterologous expression. In an effort to address some of these challenges, we profile the function and pharmacology of muscarinic acetylcholine receptors in the human parasite Brugia malayi, an etiological agent of human lymphatic filariasis. While acetylcholine-gated ion channels are intensely studied as targets of existing anthelmintics, comparatively little is known about metabotropic receptor contributions to parasite cholinergic signaling. Using multivariate phenotypic assays in microfilariae and adults, we show that nicotinic and muscarinic compounds disparately affect parasite fitness traits. We identify a putative G protein-linked acetylcholine receptor of B. malayi (Bma-GAR-3) that is highly expressed across intramammalian life stages and adapt spatial RNA in situ hybridization to map receptor transcripts to critical parasite tissues. Tissue-specific expression of Bma-gar-3 in Caenorhabditis elegans (body wall muscle, sensory neurons, and pharynx) enabled receptor deorphanization and pharmacological profiling in a nematode physiological context. Finally, we developed an image-based feeding assay as a reporter of pharyngeal activity to facilitate GPCR screening in parasitized strains. We expect that these receptor characterization approaches and improved knowledge of GARs as putative drug targets will further advance the study of GPCR biology across medically important nematodes.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Heat exchangers fabricated by additive manufacturing, related components, and related methods

A method of forming at least a component of a heat exchanger comprises introducing a feed material comprising a first portion including a matrix material and a second portion including a sacrificial material on a surface of a substrate, exposing at least the first portion to energy to form bonds between particles of the matrix material and form a first thickness of a structure, introducing additional feed material comprising the first portion over the first thickness of the structure, exposing the additional feed material to energy to form a second thickness of the structure, and removing the sacrificial material from the structure to form at least one channel in the structure. Related heat exchangers and components, and related methods are disclosed.

van Rooyen, Isabella J.↗
DOE OSTI2023

Methods of forming components of heat exchangers and methods of forming heat exchangers

A method of forming at least a component of a heat exchanger comprises introducing a feed material comprising a first portion including a matrix material and a second portion including a sacrificial material on a surface of a substrate, exposing at least the first portion to energy to form bonds between particles of the matrix material and form a first thickness of a structure, introducing additional feed material comprising the first portion over the first thickness of the structure, exposing the additional feed material to energy to form a second thickness of the structure, and removing the sacrificial material from the structure to form at least one channel in the structure. Related heat exchangers and components, and related methods are disclosed.

van Rooyen, Isabella J.↗
DOE OSTI2020

Spin-Dependent Thermoelectric Power of Nanoislands

The Seebeck effect explains the generation of electric voltage as a result of a temperature gradient. Its efficiency, defined as the ratio of the generated electric voltage to the temperature difference, is sensitive to local inhomogeneities that alter the scattering rate and the density of the conduction electrons. Spin-polarized Seebeck tunneling generates a distinct thermovoltage in spin-up and spin-down charge transport channels, which, as a key to spin caloritronics, focuses on transport phenomena related to spin and heat. Here, we report spatially resolved measurement of the spin-dependent thermovoltage in a tunneling junction formed by ferromagnetic Co nanoislands and a Ni tip using spin-dependent scanning tunneling thermovoltage microscopy (SP-STVthM). We resolve the nanoscale thermoelectric powers with respect to spin polarization, nanoisland size, stacking order of Co layers on a Cu substrate, and local sample heterogeneities. The observed thermally generated spin voltages are supported by first-principles and model calculations.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Plasma-Enhanced Atomic Layer Deposition Synthesis of Nanolayered Molybdenum Diselenide (MoSe 2 ) Thin Films for Nanoelectronics

Nanolayered molybdenum diselenide (MoSe 2 ) thin films were synthesized by plasma-enhanced atomic layer deposition (PE-ALD) using molybdenum pentachloride (MoCl 5 ) and diethyldiselenide (C 4 H 10 Se 2 ) precursors. Scanning and transmission electron microscopy revealed horizontally stacked nanolayers near the substrate and vertically oriented nanosheets at the surface of the film. X-ray diffraction confirmed the (002), (100), and (110) reflections of crystalline MoSe 2 , while X-ray photoelectron spectroscopy showed relative atomic concentrations of 33.5% Mo and 66.5% Se, consistent with stoichiometric MoSe 2 . Raman spectra exhibited characteristic E 1g , A 1g , and E$^1_{2g}$ vibrational modes. Field-effect transistors incorporating PE-ALD-grown MoSe 2 as the channel material displayed p-type behavior, demonstrating the potential of nanolayered MoSe 2 for nanoelectronic applications. This work demonstrates the feasibility of low-temperature, stoichiometric growth of nanolayered MoSe 2 by PE-ALD and its direct integration into transistor architectures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Combined Effects of Stream Hydrology and Land Use on Basin‐Scale Hyporheic Zone Denitrification in the Columbia River Basin

Abstract Denitrification in the hyporheic zone (HZ) of river corridors is crucial to removing excess nitrogen in rivers from anthropogenic activities. However, previous modeling studies of the effectiveness of river corridors in removing excess nitrogen via denitrification were often limited to the reach‐scale and low‐order stream watersheds. We developed a basin‐scale river corridor model for the Columbia River Basin with random forest models to identify the dominant factors associated with the spatial variation of HZ denitrification. Our modeling results suggest that the combined effects of hydrologic variability in reaches and substrate availability influenced by land use are associated with the spatial variability of modeled HZ denitrification at the basin scale. Hyporheic exchange flux can explain most of spatial variation of denitrification amounts in reaches of different sizes, while among the reaches affected by different land uses, the combination of hyporheic exchange flux and stream dissolved organic carbon (DOC) concentration can explain the denitrification differences. Also, we can generalize that the most influential watershed and channel variables controlling denitrification variation are channel morphology parameters (median grain size (D50), stream slope), climate (annual precipitation and evapotranspiration), and stream DOC‐related parameters (percent of shrub area). The modeling framework in our study can serve as a valuable tool to identify the limiting factors in removing excess nitrogen pollution in large river basins where direct measurement is often infeasible.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

A Scalable & Non-Destructive Characterization Strategy to Study Semiconductor/Dielectric Interfaces and Predict Wafer-Level Device Performance

The defect density present at the dielectric-semiconductor interface in an MOS structure directly influences the channel carrier characteristics in semiconductor devices, especially in wide bandgap material systems used in power devices. While these trap defects are typically quantified through electrical characterization of MOS-capacitor test structures, this treatment offers very little insight into the physical nature of interface defects. Such shortcomings demand a physical characterization strategy to guide fabrication optimization. X-ray photoelectron spectroscopy (XPS) is suggested as a viable technique to determine chemical data for dielectric interfaces formed using atomic layer deposition (ALD) on GaN substrates. Previously, 1-D XPS characterization has confirmed the presence of a Ga x O y interlayer between ALD dielectrics and the GaN substrate. In this work, XPS data is serially collected to form 2-D images of an ALD-Al 2 O 3 /GaN interface as a proof-of-concept experiment for in-situ XPS quality monitoring during ALD processing. The information provided by this work reveals some of the challenges for incorporating XPS characterization as an in-situ strategy during fabrication of GaN-based devices. Separately, electrical mapping of a 2-D array of ALD-Al 2 O 3 /GaN MOS-capacitor devices provide a means to quantify the spatial variations in interface quality across a single wafer. Physical characterization techniques, such as time-of-flight secondary ion mass spectroscopy, provide additional chemical information about the Al 2 O 3 /Ga x O y /GaN structure that complement the electrical mapping results. This analysis shows that a higher Ga x O y content correlates with higher interface state defects for trap energies deep in the band gap.

42 ENGINEERING↗
DOE OSTI2025

Thermal Optimization and Experimental Demonstration of a Silicon Carbide, Half-Bridge Power Module

This paper describes modeling and experimental work to design and demonstrate a silicon carbide (SiC), single-side-cooled power module. Two SiC metal-oxide-semiconductor field-effect transistors (MOSFET) were used for each switch position and packaged on a metalized ceramic substrate. Thermal modeling was first conducted to optimize the module packaging to minimize junction-to-fluid thermal resistance and device temperature variations. This procedure identified the optimal device placement and baseplate thickness to maximize thermal performance. A heat exchanger - incorporating impinging jets of water-ethylene glycol - was designed to cool the module's baseplate to minimize thermal resistance and pumping power. The heat exchanger used relatively low fluid velocities (<1.5 m/s) to minimize erosion-corrosion effects and relatively large fluid channel sizes (>=1 mm) to prevent clogging. The power module concept was fabricated, and experiments were conducted to measure its thermal performance. Direct current was used to power the module devices, and junction temperatures were measured via device temperature-sensitive parameters. The experimental results were found to be in good agreement with model predictions (within 2%) and yielded junction-to-fluid thermal resistance values as low as about 15 mm2 K/W at relatively low pumping power values. The results demonstrate the improved performance associated with jet impingement cooling and represent an improvement over existing channel-flow-type cold plates, which can enable improvements to power density and reliability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Off-state magnetoresistance in long-channel germanium Schottky-barrier MOSFETs

An increasing magnetic field perpendicular to an undoped semiconductor surface at low temperature is known to strengthen the binding of localized electrons to stationary ions, as the wavefunction's tails evolve from exponential to Gaussian. It is also known that application of a high bias voltage to a depleted semiconductor can liberate bound charge and induce a large drop in electrical resistance. We connect these established results to experimental electrical transport measurements on off-state germanium Schottky-barrier metal–oxide–semiconductor field-effect transistor (MOSFETs) with an aluminum oxide insulating dielectric and platinum germanide contacts. We make measurements at the three distinct orientations of the magnetic field with respect to the substrate and the current. At 6 K, we observe sharp attenuation of current by more than 2 orders of magnitude, within 60 mT, at a crossover magnetic field perpendicular to the substrate. A 1 T magnetic field attenuates the current by more than 4 orders of magnitude. The strength of the attenuation and the value of the crossover field are controlled by both the gate–source and drain–source voltages. The attenuation is much weaker when the magnetic field is parallel to the current. Finally, we orient the magnetic field parallel to the substrate, but perpendicular to the current, allowing us to distinguish charge hopping at the oxide interface from charge hopping in the bulk. In conclusion, this large off-state magnetoresistance can be exploited for cryogenic magnetic- and photo-detection, and for high-bias, low-leakage MOSFETs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Development of an ultraprecise glue-free bimorph deformable mirror with a length of 460 mm

Lead zirconate titanate (PZT) bimorph mirrors are essential for performing multiple functions, such as beam shaping, wavefront correction, and dynamic focusing with adjustable beam sizes. They typically consist of a mirror substrate with PZT electrodes bonded to the substrate using a thin epoxy film. However, glue-bonded PZT mirrors exhibit low reproducibility in measurement results. One source of this variability is water absorption by the substrate’s epoxy adhesive during wet fabrication processes, such as elastic emission machining (EEM), which leads to swelling and deformation. Additionally, longer deformable bimorph mirrors require larger PZT electrodes, further complicating their design and fabrication, particularly during bonding and ultraprecise metrology. To address these challenges, silver nanoparticles were employed to bond PZT elements to the silicon (Si) mirror, eliminating the need for epoxy glue. Here, in this study, we developed an inorganic-glue-free PZT bimorph mirror with a length of 460 mm and 28 channels. The glue-free bonding method successfully ensured the high reproducibility of measurements after water immersion. This approach resulted in a shape error of only 0.41 nm root mean square after the figure correction process using an ultraprecise EEM process. Scanning acoustic tomography and basic response function tests confirmed the success of the bonding process, showing no critical voids. Furthermore, the shape changes induced by applying voltages to the PZT electrodes closely matched predictions obtained from simulations. These results demonstrate the reliability and precision of the proposed glue-free bonding technique, paving the way for improved performance of new PZT bimorph mirrors.

Ichii, Yoshio [SLAC National Accelerator Laborator↗
DOE OSTI2022

Visible-Light-Driven, Iridium-Catalyzed Hydrogen Atom Transfer: Mechanistic Studies, Identification of Intermediates, and Catalyst Improvements

The harvesting of visible light is a powerful strategy for the synthesis of weak chemical bonds involving hydrogen that are below the thermodynamic threshold for spontaneous H 2 evolution. Piano-stool iridium hydride complexes are effective for the bluelight- driven hydrogenation of organic substrates and contrathermodynamic dearomative isomerization. In this work, a combination of spectroscopic measurements, isotopic labeling, structure–reactivity relationships, and computational studies has been used to explore the mechanism of these stoichiometric and catalytic reactions. Photophysical measurements on the iridium hydride catalysts demonstrated the generation of long-lived excited states with principally metal-to-ligand charge transfer (MLCT) character. Transient absorption spectroscopic studies with a representative substrate, anthracene revealed a diffusion-controlled dynamic quenching of the MLCT state. The triplet state of anthracene was detected immediately after the quenching events, suggesting that triplet–triplet energy transfer initiated the photocatalytic process. The key role of triplet anthracene on the post-energy transfer step was further demonstrated by employing photocatalytic hydrogenation with a triplet photosensitizer and a HAT agent, hydroquinone. DFT calculations support a concerted hydrogen atom transfer mechanism in lieu of stepwise electron/proton or proton/electron transfer pathways. Kinetic monitoring of the deactivation channel established an inverse kinetic isotope effect, supporting reversible C(sp 2 )–H reductive coupling followed by rate-limiting ligand dissociation. Mechanistic insights enabled design of a piano-stool iridium hydride catalyst with a rationally modified supporting ligand that exhibited improved photostability under blue light irradiation. The complex also provided improved catalytic performance toward photoinduced hydrogenation with H 2 and contra-thermodynamic isomerization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Superconducting qubit devices based on metal silicides

A qubit device for use in a quantum computing environment includes a semiconductor substrate, an insulating layer disposed on at least a portion of an upper surface of the substrate, and a transition metal silicide (TMSi) heterojunction disposed on at least a portion of an upper surface of the insulating layer. The TMSi heterojunction includes a link layer and at least first and second TMSi regions coupled with the link layer. The link layer may include a normal conductor, thereby forming a superconductor-normal conductor-superconductor (SNS) junction, or a geometric constriction, thereby forming a superconductor-geometric constriction-superconductor (ScS) junction. The link layer may form at least a portion of a channel including intrinsic or doped silicon.

Black, Charles T.↗
DOE OSTI2024

Selected Area Manipulation of MoS 2 via Focused Electron Beam-Induced Etching for Nanoscale Device Editing

Here we demonstrate direct-write patterning of single and multilayer MoS 2 via a focused electron beam-induced etching (FEBIE) process mediated with the XeF 2 precursor. MoS 2 etching is performed at various currents, areal doses, on different substrates, and characterized using scanning electron and atomic force microscopies as well as Raman and photoluminescence spectroscopies. Scanning transmission electron microscopy reveals a sub-40 nm etching resolution and the progression of point defects and lateral etching of the consequent unsaturated bonds. The results confirm that the electron beam-induced etching process is minimally invasive to the underlying material in comparison to ion beam techniques, which damage the subsurface material. Single-layer MoS 2 field-effect transistors are fabricated, and device characteristics are compared for channels that are edited via the selected area etching process. The source–drain current at constant gate and source–drain voltage scale linearly with the edited channel width. Moreover, the mobility of the narrowest channel width decreases, suggesting that backscattered and secondary electrons collaterally affect the periphery of the removed area. Focused electron beam doses on single-layer transistors below the etching threshold were also explored as a means to modify/thin the channel layer. The FEBIE exposures showed demonstrative effects via the transistor transfer characteristics, photoluminescence spectroscopy, and Raman spectroscopy. While strategies to minimize backscattered and secondary electron interactions outside of the scanned regions require further investigation, here, we show that FEBIE is a viable approach for selective nanoscale editing of MoS 2 devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Rewiring cell-free metabolic flux in E. coli lysates using a block—push—pull approach

Abstract Cell-free systems can expedite the design and implementation of biomanufacturing processes by bypassing troublesome requirements associated with the use of live cells. In particular, the lack of survival objectives and the open nature of cell-free reactions afford engineering approaches that allow purposeful direction of metabolic flux. The use of lysate-based systems to produce desired small molecules can result in competitive titers and productivities when compared to their cell-based counterparts. However, pathway crosstalk within endogenous lysate metabolism can compromise conversion yields by diverting carbon flow away from desired products. Here, the ‘block—push—pull’ concept of conventional cell-based metabolic engineering was adapted to develop a cell-free approach that efficiently directs carbon flow in lysates from glucose and toward endogenous ethanol synthesis. The approach is readily adaptable, is relatively rapid and allows for the manipulation of central metabolism in cell extracts. In implementing this approach, a block strategy is first optimized, enabling selective enzyme removal from the lysate to the point of eliminating by-product-forming activity while channeling flux through the target pathway. This is complemented with cell-free metabolic engineering methods that manipulate the lysate proteome and reaction environment to push through bottlenecks and pull flux toward ethanol. The approach incorporating these block, push and pull strategies maximized the glucose-to-ethanol conversion in an Escherichia coli lysate that initially had low ethanologenic potential. A 10-fold improvement in the percent yield is demonstrated. To our knowledge, this is the first report of successfully rewiring lysate carbon flux without source strain optimization and completely transforming the consumed input substrate to a desired output product in a lysate-based, cell-free system.

59 BASIC BIOLOGICAL SCIENCES↗