Initial Acoustoelastic Measurements in Olivine: Investigating the Effect of Stress on P- and S-Wave
Explore the source record for details and available documents.
Traylor, T.K.↗
SEARCH · Engineering Papers
Results for “stress state”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
On the phenomenon of curved microcracks in /(S)/90n/s laminates - Their shapes, initiation angles and locations
A variational analysis of the stress state in microcracked cross-ply laminates has been used to investigate the phenomenon of curved microcracking in /(S)/90n/s laminates. Previous investigators proposed that the initiation and orientation of curved microcracks are controlled by local maxima and stress trajectories of the principal stresses. We have implemented a principal stress model using a variational mechanics stress analysis and we were able to make predictions about curved microcracks. The predictions agree well with experimental observations and therefore support the assertion that the variational analysis gives an accurate stress state that is useful for modeling the microcracking properties of cross-ply laminates. An important prediction about curved microcracks is that they are a late stage of microcracking damage. They occur only when the crack density of straight microcracks exceeds the critical crack density for curved microcracking. The predicted critical crack density for curved microcracking agrees well with experimental observations.
Hu, Shoufeng↗
Deformation and fracture of thin sheet aluminum-lithium alloys: The effect of cryogenic temperatures
The objective is to characterize the fracture behavior and to define the fracture mechanisms for new Al-Li-Cu alloys, with emphasis on the role of indium additions and cryogenic temperatures. Three alloys were investigated in rolled product form: 2090 baseline and 2090 + indium produced by Reynolds Metals, and commercial AA 2090-T81 produced by Alcoa. The experimental 2090 + In alloy exhibited increases in hardness and ultimate strength, but no change in tensile yield strength, compared to the baseline 2090 composition in the unstretched T6 condition. The reason for this behavior is not understood. Based on hardness and preliminary Kahn Tear fracture experiments, a nominally peak-aged condition was employed for detailed fracture studies. Crack initiation and growth fracture toughness were examined as a function of stress state and microstructure using J(delta a) methods applied to precracked compact tension specimens in the LT orientation. To date, J(delta a) experiments have been limited to 23 C. Alcoa 2090-T81 exhibited the highest toughness regardless of stress state. Fracture was accompanied by extensive delamination associated with high angle grain boundaries normal to the fatigue precrack surface and progressed microscopically by a transgranular shear mechanism. In contrast the two peak-aged Reynolds alloys had lower toughness and fracture was intersubgranular without substantial delamination. The influences of cryogenic temperature, microstructure, boundary precipitate structure, and deformation mode in governing the competing fracture mechanisms will be determined in future experiments. Results contribute to the development of predictive micromechanical models for fracture modes in Al-Li alloys, and to fracture resistant materials.
Wagner, John A.↗
The Inclusion of In-Plane Stresses in Delamination Criteria
A study of delamination failure was conducted with emphasis on delamination criteria. Evidence is presented which supports the inclusion of the in-plane stresses in addition to the interlaminar stress terms in delamination criteria. The delamination is characterized as the failure of a resin rich region in between ply sets. The entire six component stress state in this resin layer is calculated through a finite element analysis, averaged over a dimension of 1.75 ply thicknesses, and used in a Modified von Mises Delamination Criterion. This criterion builds onto previous criteria by including all six stress components in the interply resin layer. The MVMDC shows good correlation to experimental data. The results show that the treatment of delamination as the failure of a finite interply resin layer is a valid method and that the MVMDC, considering the full stress state, accurately indicates delamination for different laminate families.
Fenske, Matthew T.↗
Enhanced Microseismicity During Production Pumping Cessation at the San Emidio Geothermal Field (Nevada, USA) in December 2016
Abstract Tectonic activity, geothermal fluids, and microseismic events (MSEs) tend to occur in similar locations as a result of spatiotemporal changes in the subsurface stress state. To quantify this association, we analyze data from a dense seismic array deployed at the San Emidio geothermal field, Nevada for 1 week in December 2016 to coincide with a 19.45‐hr shutdown of all injection and production pumping operations. 123 MSEs were detected, of which 101 occurred during the shutdown. The spatial association of the MSEs with the production wells suggests a causal relationship between the production cessation and the MSEs. Here we performed a detailed analysis to investigate reservoir material properties, distribution of seismically activated faults, and local stress state. We determined the hypocenters, magnitudes, and focal mechanisms for the MSEs, P‐wave tomographic velocity model, and local stress tensor. The results show that most MSEs occurred near the production wells. Magnitudes fall between −2.2 and 0.0 with larger events located closer to the production wells. Most MSEs occurred within a westward‐dipping normal fault zone in the reservoir associated with anomalously low P‐wave velocity values. The focal mechanism and stress inversion results show predominantly normal faulting with the maximum horizontal stress oriented north‐south. We suggest that the MSEs during shutdown were triggered on pre‐existing, small‐scale, critically stressed fault patches in the reservoir as the pore pressure increased around the production wells when the production pumping ceased. We interpret the larger MSE magnitudes closer to the production wells as a result of higher pore pressure increase.
15 GEOTHERMAL ENERGY↗
Damage accumulation in closed cross-section, laminated, composite structures
The need for safe, lightweight, less expensive, and more reliable launch vehicle components is being driven by the competitiveness of the commercial launch market. The United States has lost 2/3 of the commercial lunch market to Europe. As low cost Russian and Chinese vehicles become available, the US market share could be reduced even further. This international climate is driving the Single Stage To Orbit (SSTO) program at NASA. The goal of the SSTO program is to radically reduce the cost of safe, routine transportation to and from space with a totally reusable launch vehicle designed for low-cost aircraft-like operations. Achieving this goal will require more efficient uses of materials. Composite materials can provide this program with the material and structural efficiencies needed to stay competitive in the international launch market place. In satellite systems the high specific properties, design flexibility, improved corrosion and wear resistance, increased fatigue life, and low coefficient of thermal expansion that are characteristic of composite materials can all be used to improve the overall satellite performance. Some of the satellites that may be able to take advantage of these performance characteristics are the Tethered Satellite Systems (TOSCIFER, AIRSEDS, TSS2, SEDS1, and SEDS2), AXAF, GRO, and the next generation Hubble Space Telescope. These materials can also be utilized in projects at the NASAIMSFC Space Optics Technology and System Center of Excellence. The successful implementation of composite materials requires accurate performance characterization. Materials characterization data for composite materials is typically generated using flat coupons of finite width. At the free edge of these coupons the stress state is exacerbated by the presence of stiffness and geometric discontinuities. The exacerbated stress state has been shown to dominate the damage accumulation in these materials and to have a profound affect on the material constants. Space structures typically have closed cross-sections, absent of free edges. As a result, composite material characterization data generated using finite width flat specimens does not accurately reflect the performance of the composite materials used in a closed cross-section structural configuration. Several investigators have recognized the need to develop characterization techniques for composite materials in closed cross-sectioned structures. In these investigations test methods were developed and cylindrical specimens were evaluated. The behavior of the cylindrical specimens were observed to depart from behavior typical of flat coupons. However, no attempts were made to identify and monitor the progression of damage in these cylindrical specimens during loading. The identification and monitoring of damage is fundamental to the characterization of composite materials in closed cross-section configurations. In the study reported here, a closed cross-sectioned test method was developed to monitor damage progression in 2 in. diameter cylindrical specimens and 1.5 in. finite width flat coupons subjected to quasi-static, tensile loading conditions. Damage in these specimen configurations was monitored using pulse echo ultrasonic, acoustic emission, and X-ray techniques.
Bucinell, Ronald B.↗
Kink band and shear band localization in anisotropic perfectly plastic solids
Shear-driven strain localization has been observed in a wide variety of materials and may take the form of shear bands or kink bands. Based on observations of kink bands in plastically anisotropic metallic nanolaminates and single crystal metals, here we posit that, for the specific case of isochoric deformation, the kinematics of kink band formation are indistinguishable from those of plane strain shear band formation. The only distinction between shear bands and kink bands in these systems would then be that kink bands ‘lock up’ at a particular value of material rotation while shear bands may progress to arbitrarily high strains. In order to investigate whether strong material anisotropy is sufficient to arrest shear localization at a geometry that matches the classic kink band geometry, we model the development of a band of simple shear within an anisotropic perfectly plastic material. The resulting analytical model provides the stress state needed to maintain the kinematics of simple shear as a function of material anisotropy, deformation band orientation, and shear strain (or equivalently, material rotation). It is found that plastic anisotropy can promote either kink band or shear band formation depending on the loading orientation. When the deviatoric stress is positive parallel to the plane of anisotropy, shear localization may progress without bound and a shear band is produced. When the deviatoric stress is negative parallel to the plane of anisotropy, shear localization is arrested after a certain material rotation, resulting in a kink band. Examination of the requisite applied stress state during kink band formation provides an explanation for the experimentally-observed ‘lock up’ geometry. Solutions for the band boundary inclination angle are obtained and used to provide bounds on permissible band angles for both shear bands and kink bands.
36 MATERIALS SCIENCE↗
Simulation of mixed-mode fracture using the combined finite–discrete element method
It has been shown experimentally that under mixed tensile and compressive stress states, a corresponding mixed-mode fracture will occur. Here, the formation of mixed-mode fractures is investigated using the combined finite–discrete element method. A series of simulations with confining pressures ranging from 7.5 to 150 MPa generate a spectrum of mixed-mode failure conditions. These stress states at failure span the transition from the tensile to compressive failure. The models reproduce previous experiments on Carrara marble using a dog-bone geometry, and a comparison shows good qualitative agreement with the experimental observations. This paper demonstrates that mixed-mode fracture can be captured via numerical simulations and identifies areas where further research is required to better understand mixed-mode fracture processes.
42 ENGINEERING↗
Biaxial Stress Limit for ULDB Film
The current ULDB design applies stress to the shell film biaxially to control creep in the latitudinal direction. The recent change in design paradigm, from a uniaxial to biaxial stress state basis, arose from a new perspective that the biaxial loading can control strain in both principal surface dimensions as discussed below. The current ULDB project path was thus enabled by a more thorough understanding of the nonlinear viscoelastic properties of the shell film material, linear low-density polyethylene (LLDPE). Although a very similar material is also used in NASA zero-pressure (ZPB) and long-duration balloons (LDB), the different stress state requires a new approach to shell material qualification.
Sterling, W. J.↗
Slip Tendency Analysis of Fracture Networks to Determine Suitability of Candidate Testbeds for the EGS Collab Hydroshear Experiment
Experiment 2 of the EGS Collab project is aimed at testing stimulation by hydro-shearing of existing natural fractures, versus Experiment 1, which is focused on hydraulic fracturing a rock mass to enhance permeability. The main criterion for the testbed selection in Experiment 2 is the presence of an interconnected network of fractures, at least 10 meters in extent, and with orientations such that shear slip can be induced at injection pressures less than the minimum horizontal stress (Shmin). The feasibility analysis for this experiment requires a well-constrained stress state along with well-characterized fracture networks. The fracture systems at two candidate locations in the Sanford Underground Research Facility (SURF), the 4850 Level (number refers to depth below ground surface in feet) and the 4100 Level, have been characterized to different extents. The 4850 Level has a well-characterized Discrete Fracture Network (DFN) from borehole (drilled for an experimental test bed) and drift observations. In contrast, the 4100 level has a fracture network characterized only by observations from the drift wall, which provides little constraint on fracture extents. This paper will present assessments for the interpreted slip potential for the natural fractures at the two locations. Data uncertainties are addressed by performing a probabilistic analysis that takes into account the uncertainty in the stress state, uncertainty in the fracture properties, and preliminary borehole locations. There is strong evidence of shear stimulation of some natural fractures in Experiment 1 on the 4850 level. We use examples of natural fractures strongly linked to shear stimulation in Experiment 1 from multiple monitoring indicators to test the consistency of the stress model and guide the uncertainty interpretation. This analysis is intended to guide the site selection process for Experiment 2 by highlighting the fracture orientations that are likely to be shear-stimulated in a majority of modeled realizations.
40 EE - Geothermal Technologies Office (EE-4G)↗
Effects of moisture, residual thermal curing stresses and mechanical load on the damage development in quasi-isotropic laminates
Classical laminate theory and a finite element model were used to predict stress states prior to the first formation of damage in laminates fabricated from T/300/5208. Crack patterns characteristic of the laminate in a wet or dry condition were also predicted using a shear lag model. Development of edge damage was recorded and observed during the test by transferring an image of the damage from the edge surface on to a thin acetate sheet such that the damage imprinted could be immediately viewed on a microfiche card reader. Moisture was shown to significantly alter the interior and edge dry stress states due to swelling and a reduction of elastic properties and to reduce the transverse strength in 90 deg plies. A model was developed in order to predict changes in first ply failure laminate loads due to differences in stacking sequence together with a wet or dry environmental condition.
Kriz, R. D.↗
Development of a Numerical Model of Hypervelocity Impact into a Pressurized Composite Overwrapped Pressure Vessel
As the outlook for space exploration becomes more ambitious and spacecraft travel deeper into space than ever before, it is increasingly important that propulsion systems perform reliably within the space environment. The increased reliability compels designers to increase design margin at the expense of system mass, which contrasts with the need to limit vehicle mass to maximize payload. Such are the factors that motivate the integration of high specific strength composite materials in the construction of pressure vessels commonly referred to as composite overwrapped pressure vessels (COPV). The COPV consists of a metallic liner for the inner shell of the COPV that is stiff, negates fluid permeation and serves as the anchor for composite laminates or filaments, but the liner itself cannot contain the stresses from the pressurant it contains. The compo-site-fiber reinforced polymer (CFRP) is wound around the liner using a combination of hoop (circumferential) and helical orientations. Careful consideration of wrap orientation allows the composite to evenly bear structural loading and creates the COPV's characteristic high strength to weight ratio. As the CFRP overwrap carries most of the stresses induced by pressurization, damage to the overwrap can affect mission duration, mission success and potentially cause loss-of-vehicle/loss-of-crew. For this reason, it is critical to establish a fundamental understanding of the mechanisms involved in the failure of a stressed composite such as that of the COPV. One of the greatest external threats to the integrity of a spacecraft's COPV is an impact from the meteoroid and orbital debris environments (MMOD). These impacts, even from submillimeter particles, generate extremely high stress states in the CFRP that can damage numerous fibers. As a result of this possibility, initial assumptions in survivability analysis for some human-rated NASA space-craft have assumed that any alteration of the vessel due to impact is considered a catastrophic failure. This assumption is conservative and made due to lack of knowledge on the level of allow-able damage to the composite overwrap that can be sustained and still allow successful completion of the mission. To quantify the allowable damage level to the composite overwrap involves assessing stress redistribution following damage as well as evaluating possible time-dependent mechanisms involved in the COPV response to an impact event. Limited published work in this subject has shown that COPV can withstand at least some level of damage due to high energy impacts. These observations have been confirmed and expanded upon in recent experimental research performed by NASA. This research has demonstrated that there is not only robustness in a COPV to compensate for CFRP damage, but has also identified two significant failure modes for pressurized COPV. The lowest threshold failure mode involves the perforation of the vessel, and the highest threshold failure mode is the catastrophic rupture. While both of these failure modes mean a loss of the COPV, system robustness affords some tolerance to the venting as opposed to the more catastrophic rupture. As a consequence, it is necessary to understand the conditions that result in the transition between these failure modes. The aforementioned experimental research has been performed in both the unpressurized and pressurized condition to identify the damage level that triggered the failure thresh-old. This COPV test program was sponsored by the NASA Engineering and Safety Center (NESC), and tests were performed at NASA White Sands Test Facility (WSTF). Planning and coordination were provided by NASA JSC Hypervelocity Impact Technology (HVIT) group, and the COPVs were provided by the ISS Program. Unpressurized testing has been conducted at the pressure of the vacuum test chamber, while, the pressurized testing has been conducted at 290 +/- 10 bar (4,200 100 psi) using nitrogen as the pressurizing gas, which corresponds to the design pressure for the target COPV. In this research, spherical aluminum projectiles with varying diameter has been chosen as the impactor. For the unpressurized COPV, the dependence of penetration up to the dependence of hole size in the liner has been obtained as a function of impact conditions. For the pressurized research, the dependence of penetration up to rupture has been obtained as a function of im-pact conditions. Two representative post-test photographs of the failed COPV's from a nor-mal impact into the COPV surface are shown in Fig. 1. These images display the dramatic difference between failure modes, venting (Fig. 1a) and rupture (Fig. 1b). For venting, liner perforation, severed composite fibers/tows and ply delamination are commonly observed damage characteristics of this COPV failure mode. In the case of rupture, the COPV typically experienced a separation of its domed regions and severe break-up of the cylindrical region. Fully understanding the transition from venting to rupture experimentally is costly and potentially unachievable for conditions that cannot be generated in the laboratory. These shortcomings have motivated the performance of three-dimensional numerical simulations to expand the existing experimental database. These simulations have been carried out with the nonlinear-structural-dynamics, analysis-tool, CTH. A typical pressure contour plot from an impact simulation of an entire COPV is shown in Fig. 2. To generate the COPV stress state without initiating a shock wave, the pressure in the simulated COPV is ramped up to the final pressure over a millisecond prior to impact of the projectile with nitrogen gas. Figure 2a shows the system in this initial condition. After one millisecond, a projectile is initiated into the simulation and impacts the COPV. Figure 2b shows the system after this impact. In the figure, the onset of venting is represented as the change in pressure (μbar), red to green, at the perforation site. Also seen in the figure is the eroded projectile that had passed into the COPV vessel with the generated shock wave in the pressurant propagating just ahead of the material. In this paper, pertinent experimental details and the development of the material constitutive models necessary for this work along with the efforts to validate their use are dis-cussed. The simulation results are presented and compared with the NASA experimental observations. While work is on-going from this effort, early observations pertinent to the failure threshold are presented.
Garcia, M. A.↗
A better understanding of the mechanics of borehole breakout utilizing a finite strain gradient-enhanced micropolar continuum model
Borehole breakout denotes the failure in rock mass subjected to drilling, caused by stress concentrations exceeding the material strength. Depending on the material properties, the preexisting in situ stress state, and the borehole dimensions, different types of borehole breakout, such as spiral-shaped breakout or v-shaped breakout, are distinguished in the literature. In the present work, we address the influence of the material properties on the predicted borehole breakout mode in a comprehensive finite element study. To this end, herein we employ a gradient-enhanced micropolar damage-plasticity model based on the Mohr–Coulomb strength criterion, formulated in the finite strain regime, which is calibrated based on experimental results from plane strain compression tests on Red Wildmoor sandstone. In the numerical study, the influence of the in situ stress state, the material friction angle, plastic dilation, post peak residual strength, and the inherent material length scale parameters are investigated. Thereby, we demonstrate that depending on the material parameters, substantially different failure modes, characterized by strongly localized shear bands or diffuse failure zones, are predicted. It is shown that in particular the brittleness of the material in the post peak regime has a major influence on the predicted breakout type. Moreover, a statistical validation of the results is obtained by considering different random field distributions of the initial material strength.
58 GEOSCIENCES↗
Probabilistic Failure Criterion of SiC/SiC Composites Under Multiaxial Loading
Owing to its excellent mechanical properties and stability under high temperature and neutron irradiation conditions, SiC/SiC composites have emerged as a promising material for light water reactors (LWRs) in the development of accident-tolerant fuel (ATF) systems. Structural integrity and retention of hermeticity are two crucial requirements for SiC/SiC claddings during normal operations, and both of them are closely related to the proportional limit stress (PLS) of the material. Understanding the behavior of SiC/SiC composites under multiaxial stress states and developing a probabilistic approach for evaluating the structural vulnerability are of paramount importance for reliability-based analysis and design of SiC/SiC composite claddings. So far, there has been very limited effort towards experimental and analytical investigations of probabilistic failure of SiC/SiC claddings. This critical knowledge gap motivates this research. A probabilistic failure criterion for SiC/SiC composites under multi-axial loading is developed, and this criterion is incorporated into reliability analysis of the structural integrity of SiC/SiC fuel cladding. The research consists of two parts: 1) experimental investigation of multiaxial failure behavior of SiC/SiC composites, and 2) theoretical modeling of time-dependent probabilistic failure of SiC/SiC cladding. In the experimental investigation, the PLS is determined through the examination of stress-strain response, the acoustic emission measurement, as well as the X-ray computed tomography. The theoretical framework is derived by combin- ing the finite weakest-link statistical model and the subcritical damage growth model. This theoretical model captures the time-dependent failure mechanism of the material, which has a major consequence for predicting the lifetime distribution of the cladding. Meanwhile, the model also predicts that the failure statistics of the cladding depends strongly on the cladding length. The results of the multiaxial experiments reveal the level of statistical variation of the PLS of SiC/SiC materials under different stress states. The theoretical model provides a robust analytical tool for extrapolation of small-scale laboratory test results to the behavior of full-scale claddings. These findings establish a scientific foundation for the development of reliability-based design of SiC/SiC fuel claddings, which will play an essential role in improving the structural safety and integrity of LWRs.
42 ENGINEERING↗
Thick thermal barrier coatings for diesel engines
Caterpillar's approach to applying Thick Thermal Barrier Coatings (TTBC's) to diesel engine combustion chambers has been to use advanced modeling techniques to predict engine conditions and combine this information with fundamental property evaluation of TTBC systems to predict engine performance and TTBC stress states. Engine testing has been used to verify the predicted performance of the TTBC systems and provide information on failure mechanisms. The objective of Caterpillar's subcontract with ORNL is to advance the fundamental understanding of thick thermal barrier coating systems. Previous reviews of thermal barrier coating technology concluded that the current level of understanding of coating system behavior is inadequate and the lack of fundamental understanding may impede the application of TTBC's to diesel engines. Areas of TTBC technology being examined in this program include powder characteristics and chemistry; bond coat composition; coating design, microstructure, and thickness as they affect properties, durability, and reliability; and TTBC 'aging' effects (microstructural and property changes) under diesel engine operating conditions. Methods to evaluate the reliability and durability of TTBC's have been developed that attempt to understand the fundamental strength of TTBC's for particular stress states.
Beardsley, M. B.↗
Thick thermal barrier coatings for diesel engines
Caterpillar's approach to applying thick thermal barrier coatings (TTBC's) to diesel engine combustion chambers has been to use advanced modeling techniques to predict engine conditions and combine this information with fundamental property evaluation of TTBC systems to predict engine performance and TTBC stress states. Engine testing has been used to verify the predicted performance of the TTBC systems and provide information on failure mechanisms. The objective Caterpillar's program to date has been to advance the fundamental understanding of thick thermal barrier coating systems. Previous reviews of thermal barrier coating technology concluded that the current level of understanding of coating system behavior is inadequate and the lack of fundamental understanding may impeded the application of TTBC's to diesel engines. Areas of TTBC technology being examined in this program include powder characteristics and chemistry; bond coat composition; coating design, microstructure, and thickness as they affect properties, durability, and reliability; and TTBC 'aging' effects (microstructural and property changes) under diesel engine operating conditions. Methods to evaluate the reliability and durability of TTBC's have been developed that attempt to understand the fundamental strength of TTBC's for particular stress states.
Beardsley, M. Brad↗
Revisiting Multi-Material Composite Structures with Homogenized Composite Properties
Composite structures inherently develop residual stresses during their curing process. Driven predominately by mismatched thermal strains between differing materials or ply orientations, but also affected by curing process phenomena like polymer shrinkage, these residual stresses can lead to failure within composite structures. There are several methods varying in complexity that can be used to model the development of residual stresses, all of which are capable of capturing sufficient detail to understand the residual stress state at the ply level. However, explicitly modeling all plies of a layup in a composite structure can be prohibitively expensive based on the number of plies, structure size, and required element size. The computational cost can be reduced through the homogenization of the composite layup without losing much fidelity of the overall response of the structure. The homogenization process reduces the many plies of a laminate to a single lamina that reduces complexity and increases the mesh size where a single element can span multiple plies. This report focuses on verification and validation efforts for a homogenization process using a suite of finite element simulations rather than an analytic solution derived from classical laminate theory. Initial verification using representative element volumes indicated there was minimal error in the homogenization process; however, this compounded to a small, but acceptable error in strip and split ring experimental composite structures. The error does under predict the residual stress state in the strip and split ring and should be accounted for when simulating composite structures with homogenized properties.
36 MATERIALS SCIENCE↗