Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Dynamic oxidation of (Mn,Co) 3 O 4 -Coated interconnects for solid oxide electrolysis cells

Solid oxide electrolysis cell stacks are expected to experience dynamic conditions when using renewable electricity derived from wind or solar power. To address this scenario, (Mn,Co) 3 O 4 (MCO)-coated Crofer 22 APU interconnect coupons are subjected to thermal cycling, and intermittent current density, with gas compositions relevant to high-temperature electrolysis (elevated steam:hydrogen ratio and oxygen content). Defects are also intentionally introduced in the MCO coating, to assess whether the difference in oxidation properties of the adjacent coated and uncoated (defective) surfaces causes sufficient stress to damage the protective oxide scale. Specimens with defects are subjected to oxidation for 1000 h at 800 °C, or thermal cycling. Before thermal cycling, some specimens are pre-oxidized to create a thick oxide scale to mimic the scale thickness expected after ~30 kh operation. In all cases, the coating and oxide scale remain well adhered with no cracking observed. Area-specific resistance (ASR) is monitored in both single-atmosphere and dual-atmosphere conditions, and the ASR is stable and is not impacted by dynamic cycling of the current density. Finally, this work provides confidence that the MCO coated interconnect will function as needed in dynamic operation conditions, even with coating defects.

08 HYDROGEN↗

Degradation in Solid Oxide Cells During High Temperature Electrolysis

Idaho National Laboratory has an ongoing project to generate hydrogen from steam using solid oxide electrolysis cells. One goal of that project is to address the technical and degradation issues associated with solid oxide electrolysis cells. This report covers a variety of these degradation issues, which were discussed during a workshop on “Degradation in Solid Oxide Electrolysis Cells and Strategies for its Mitigation,” held in Phoenix, AZ on October 27, 2008. Three major degradation issues related to solid oxide electrolysis cells discussed at the workshop are: • Delamination of O2-electrode and bond layer on steam/O2-electrode side • Contaminants (Ni, Cr, Si, etc.) on reaction sites (triple-phase boundary) • Loss of electrical/ionic conductivity of electrolyte. This list is not all inclusive, but the workshop summary can be useful in providing a direction for future research related to the degradation of solid oxide electrolysis cells.

99 GENERAL AND MISCELLANEOUS↗

Cathode material for low temperature solid oxide fuel cells

The present invention relates to a solid oxide (or protonic ceramic) fuel cell, a cathode for a solid oxide (or protonic ceramic) fuel cell, and a method of making the same. More specifically, the cathode for a solid oxide (or protonic ceramic) fuel cell utilizes a phase-pure perovskite structure of the compound BaCo.sub.0.4Fe.sub.0.4Zr.sub.0.2-xY.sub.xO.sub.3-.delta., where x is between about 0 and about 0.2. The cathode material may then be utilized in a SOFT or a PCFC as either a thin film porous cathode or as nanoparticles infiltrated into a cathode bone having a different structure.

36 MATERIALS SCIENCE↗

Nonlinear model predictive control for mode‐switching operation of reversible solid oxide cell systems

Abstract Solid oxide cells (SOCs) are a promising dual‐mode technology for the production of hydrogen through high‐temperature water electrolysis, and the generation of power through a fuel cell reaction that consumes hydrogen. Switching between these two modes as the price of electricity fluctuates requires reversible SOC operation and accurate tracking of hydrogen and power production set points. Moreover, a well‐functioning control system is important to avoid cell degradation during mode‐switching operation. In this article, we apply nonlinear model predictive control (NMPC) to an SOC module and supporting equipment and compare NMPC performance to classical proportional‐integral (PI) control strategies, while switching between the modes of hydrogen and power production. While both control methods provide similar performance across various metrics during mode switching, NMPC demonstrates a significant advantage in reducing cell thermal gradients and curvatures (mixed spatial‐temporal partial derivatives), thereby helping to mitigate long‐term degradation.

08 HYDROGEN↗

An Active and Resilient Bilayer Oxygen Electrode for Intermediate Temperature Reversible Solid Oxide Cells

High temperature solid oxide cells (SOCs) have intrinsic advantage in efficiency over conventional internal combustion engines for power generation and low-temperature electrolysis cells for H2 production. This efficiency advantage could potentially lead to cost saving and emission reduction. However, commercialization of the current SOCs technology is hindered by its poor durability. One major component with the durability issue is oxygen electrode (OE). For example, the durability of OEs can be negatively affected by the gaseous Cr-species originated from the air oxidation of high-temperature alloy interconnect. For electrolysis operation, on the other hand, delamination of OE from electrolyte, particularly at high current densities, has been identified as a major cause for the performance degradation. Therefore, developing robust and active OEs is of critical importance to SOC technology. WE have previously demonstrated a new bilayer OE with strong activity and stability. Here in this presentation, we present recent results of electrochemical characterization on bilayer OE operating under both fuel cell and electrolysis modes. We will first show the optimization of bilayer OE in terms of thickness, morphology, and calcination temperature and their impacts on cell area specific resistance (ASR). With three-electrode symmetric cell configuration, we also show the results of charge transfer ASR of bilayer OE as a function of current density, temperature, and time in different atmospheres. The results are further compared with the baseline OE (LSCF+GDC) to demonstrate the advantage of bilayer OE.

Huang, Kevin↗

NMPC for Setpoint Tracking Operation of a Solid Oxide Electrolysis Cell System

Solid oxide electrolysis cells (SOECs) are a promising technology to generate hydrogen through water electrolysis. However, intermittent renewable energy requires SOECs to transition between hydrogen production setpoints as the price of electricity fluctuates. A well-functioning control system is important to avoid cell degradation during setpoint tracking operation. In this work, we apply nonlinear model predictive control (NMPC) to an SOEC module and supporting equipment and compare NMPC performance to classical PI control while ramping between hydrogen production setpoints. We find that these control methods provide similar performance in many metrics, but NMPC significantly reduces cell thermal gradients during the setpoint transition.

Allan, Douglas↗

Computationally Guided Design of Multiple Impurities Tolerant Cathode for Solid Oxide Fuel Cell Applications

Solid oxide fuel cells (SOFCs) have been recognized as promising candidates in the demand of reducing the dependence on fossil fuels, which is one of the solutions to the threat of global warming. It was reported that the direct chemical-to-electrical energy conversion in SOFCs comes with negligible emission of greenhouse gases and up to 60% working efficiency. SOFC has unique advantages over traditional power generation technologies and other types of fuel cells due to the use of relatively inexpensive materials, low sensitivity to poisoning impurities in fuels, relatively high conversion efficiency, and fuel flexibility (like carbon-based fuels). However, during the SOFC operation, the cathode is exposed to intrinsic and extrinsic airborne contaminants at high temperatures (600–900°C), leading to their reaction with electrode materials, irreversible chemical and structural changes, and electrochemical performance degradation. of which CO2, SO2, Cr6+ and H2O are known to be concerns. Thus, developing a comprehensive understanding of the multiple impurities poisoning of SOFC cathodes in the presence of single or multiple impurities is necessary to address the long-term degradation of the SOFC cathode systems at operating conditions. An integrated computational and experimental approach has been utilized in the current work aiming at the comprehensive investigation of the cathode materials under single or multiple impurities poisoning effects, understanding the multiple impurities poisoning mechanism(s), and improving the long-term durability of the SOFC cathodes to develop better performing impurity-tolerant cathode materials. We first examined the agreement between the simulation approach and the experimental observations at various atmospheric and temperature conditions to confirm the reliability of CALPHAD for poisoning simulations in these cathodes. Then, using this approach, we investigated the accelerated testing protocol, which has become the standard method for conducting impurity poisoning experiments involving these cathode materials. We found our simulation approach is able to predict in which systems, i.e., cathode material and treatment environment, the accelerated testing protocols reflect actual operating conditions. Finally, in-depth simulations were done for these three candidate cathodes under different experimental conditions and suggested directions toward alternative cathode materials that have superior impurity tolerance.

36 MATERIALS SCIENCE↗

Generator module architecture for a large solid oxide fuel cell power plant

A solid oxide fuel cell module contains a plurality of integral bundle assemblies, the module containing a top portion with an inlet fuel plenum and a bottom portion receiving air inlet feed and containing a base support, the base supports dense, ceramic exhaust manifolds which are below and connect to air feed tubes located in a recuperator zone, the air feed tubes passing into the center of inverted, tubular, elongated, hollow electrically connected solid oxide fuel cells having an open end above a combustion zone into which the air feed tubes pass and a closed end near the inlet fuel plenum, where the fuel cells comprise a fuel cell stack bundle all surrounded within an outer module enclosure having top power leads to provide electrical output from the stack bundle, where the fuel cells operate in the fuel cell mode and where the base support and bottom ceramic air exhaust manifolds carry from 85% to all 100% of the weight of the stack, and each bundle assembly has its own control for vertical and horizontal thermal expansion control.

30 DIRECT ENERGY CONVERSION↗

Electrode Design for Low Temperature Direct-Hydrocarbon Solid Oxide Fuel Cells

In certain embodiments of the present disclosure, a solid oxide fuel cell is described. The solid oxide fuel cell includes a hierarchically porous cathode support having an impregnated cobaltite cathode deposited thereon, an electrolyte, and an anode support. The anode support includes hydrocarbon oxidation catalyst deposited thereon, wherein the cathode support, electrolyte, and anode support are joined together and wherein the solid oxide fuel cell operates a temperature of 600.degree. C. or less.

Chen, Fanglin↗

Electrode design for low temperature direct-hydrocarbon solid oxide fuel cells

In certain embodiments of the present disclosure, a solid oxide fuel cell is described. The solid oxide fuel cell includes a hierarchically porous cathode support having an impregnated cobaltite cathode deposited thereon, an electrolyte, and an anode support. The anode support includes hydrocarbon oxidation catalyst deposited thereon, wherein the cathode support, electrolyte, and anode support are joined together and wherein the solid oxide fuel cell operates a temperature of 600.degree. C. or less.

30 DIRECT ENERGY CONVERSION↗

Theoretical understanding of stability of the oxygen electrode in a proton-conductor based solid oxide electrolysis cell

The oxygen electrode in a proton-conductor based solid oxide cells is often a triple-conducting material that enables the transport and exchange of electrons (e - ), oxygen ions (O 2- ), and protons (H + ), thus expanding active areas to enhance the oxygen electrode activity. In this work, a theoretical model was developed to understand stability of tri-conducting oxygen electrode by studying chemical potentials of neutral species (i.e., μ o 2 , μ H 2 , and μ H 2 O ) as functions of transport properties, operating parameters, and cell geometry. Our theoretical understanding shows that (1): In a conventional oxygen-ion based solid oxide cell, a high μ o 2 (thus high oxygen partial pressure) exists in the oxygen electrode during the electrolysis mode, which may lead to the formation of cracks at the electrode/electrolyte interface. Further, while in a proton-conductor based solid oxide cell, the μ o 2 is reduced significantly, suppressing the crack formation, and resulting in improved performance stability (2). In a typical proton-conductor based solid oxide electrolyzer, the dependence of μ o 2 on the Faradaic efficiency is negligible. Hence, approaches to block the electronic current can improve the electrolysis efficiency while achieving stability (3). The difference of the μ o 2 (thus p o 2 ) between the oxygen electrode and gas phase can be reduced by using higher ionic conducting components and improving electrode kinetics, which lead to further improvement of electrode stability.

08 HYDROGEN↗

Defect Thermodynamics and Transport Properties of Perovskite and Fluorite Materials for Solid-Oxide and Proton Conducting Oxide Cells Evaluated Based on Density Functional Theory Modeling

Density functional theory based defect thermodynamic modeling was performed to determine the effect of humidity and H2/O2 gas pressure on various defect chemistry and transport properties of perovskite and fluorite oxides for solid-oxide and proton-conducting-oxide cell applications, with inclusion of the electronic-conducting oxides (as electrodes) and insulating oxides (as electrolytes). Automatic defect generation workflow and first-principles charged defect analysis were implemented on NETL Joule supercomputer for modeling defect equilibria and transport properties of insulating oxides as electrolytes in SOCs and proton-conducting ceramic cells. A GNU Octave defect model subroutines were developed to facilitate defect modeling of electronic conducting oxides in a wide range of operating conditions guided by modeling and experiments. The model includes the hydride defect formation reaction under reducing conditions and allows to incorporate nonstoichiometry effects on the defect thermodynamic parameters. The developed model serves as a platform to facilitate fundamental understanding of the defect thermodynamics in SOC oxide materials and can be used as a novel tool in computational materials screening for SOC and other energy applications.

Lee, Yueh-Lin↗

Assessment of Protective Coatings for Metal-Supported Solid Oxide Electrolysis Cells

Green hydrogen is essential to achieving carbon neutrality, and solid oxide electrolysis cells can produce hydrogen using renewable power and waste heat. Insufficient long-term durability of solid oxide electrolysis cells has impeded their commercialization. Here, coatings in the porous stainless steel support of metal-supported solid oxide electrolysis cells (MS-SOECs) are used to dramatically improve their performance and durability. The long-term degradation rate of uncoated MS-SOECs is highly dependent on the current density, with the fastest degradation occurring at the highest current density tested, 0.5 A cm -2 . At this current density, coatings are quite effective. Three protective coatings, Co 3 O 4 deposited by atomic layer deposition (ALD), Co 3 O 4 deposited by electroplating deposition (ED), and CuMn 1.8 O 4 (CMO) deposited by electrophoretic deposition (EPD), are explored to enhance the performance of MS-SOECs with La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 -Sm 0.2 Ce 0.8 O 3 (LSCF-SDC) as the oxygen catalyst and SDC-Ni as the fuel catalyst. The initial average current density at 1.4 V is increased with coatings. It is 0.83 mA cm -2 for the ALD cells, 1.05 mA cm -2 for the ED cells, and 1.13 mA cm -2 for the EPD cells, compared to 0.65 mA cm -2 for the bare cells at 700 °C with 50% H 2 -50% H 2 O. The degradation rate over 1000 h of continuous operation is reduced from 36% to 26%, 27%, and 19% kh -1 with the three coatings, respectively. Furthermore, these improvements are ascribed to reduced Cr poisoning on the oxygen catalyst, which is one of the primary degradation modes for this type of MS-SOEC.

25 ENERGY STORAGE↗

Performance of stainless steel interconnects with (Mn,Co) 3 O 4 -Based coating for solid oxide electrolysis

Mixed transition-metal oxide coatings are commonly applied to stainless steel interconnects for solid oxide cell stacks. Such coatings reduce oxidation and Cr evaporation rates, leading to improved degradation rate and stack lifetime. Here, the ChromLok™ MCO-based composition (Mn,Co) 3 O 4 is applied to Crofer 22 APU stainless steel and evaluated specifically for application in solid oxide electrolyzer stacks operating around 800 °C and utilizing oxygen-ion-conducting solid oxide cells. The MCO coating is found to decrease the stainless steel oxidation rate by about one order of magnitude, and decrease the Cr evaporation rate by fourfold. Furthermore, the coating also dramatically lowers the rate of area-specific resistance increase for stainless steel coupons oxidized for 500 h with constant current applied, from 33 mΩ*cm 2 kh -1 for an uncoated coupon to less than 4 mΩ*cm2 kh -1 for coated coupons. The coating is demonstrated on full-scale interconnects for single-cells, where the coating dramatically reduces degradation rate, and for a stack, which displays stable operation for 700 h.

08 HYDROGEN↗

Assessment of the Distributed Generation Market Potential for Solid Oxide Fuel Cells

The focus of the solid oxide fuel cell (SOFC) program at the National Energy Technology Laboratory (NETL) is to develop low-cost, highly efficient solid oxide fuel cell power systems that are capable of simultaneously producing electric power with carbon capture when integrated with gasification. To accomplish this goal, research and demonstration projects are being undertaken to enhance the reliability and the robustness of the SOFC system. NETL’s SOFC technology roadmap is focused on developing and demonstrating progressively larger megawatt electric (MWe) class natural-gas-based systems to validate and advance SOFC technology for natural gas and gasified coal-based utility scale power generation. As the SOFC technology advances from its current state to utility scale, it is possible that MWe class systems could penetrate the distributed generation (DG) market segment. If the SOFC technology were to penetrate the DG market, this would have the added benefit of lowering system costs by establishing operational experience and a manufacturing base. This report analyzed the strengths of the SOFC system in conjunction with relevant DG market segments in the United States (U.S.) and determined that natural gas compressor stations, grid strengthening, and data centers were potential early market-entry opportunities. These three DG market segments are projected to demand two gigawatts (GWs) of additional power between now and 2018 and 25 GWs between now and 2040. Historical experiences with related technology, including effects of increased production capacity on capital costs, were used to evaluate the market penetration necessary for a cost competitive DG SOFC system. This analysis showed that the DG SOFC system becomes cost competitive with other fossil-fuel based DG technologies after 25 MWe of installed capacity, around 2025, based on the demonstration of the first SOFC DG unit in the year 2020. The SOFC DG application validates and enables the technology for utility scale systems with carbon capture and forms an essential first phase of the NETL technology development roadmap, which is based on the vision to develop a commercially competitive utility-scale system with carbon capture.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Solid oxide metal-air redox batteries (SOMARB)

The solid oxide metal-air redox batteries (SOMARB), composed of reversible solid oxide fuel cell (RSOFC) and energy storage unit (ESU), is an emerging technology for large-scale energy storage owing to its advantages in high energy density, high rate capability, decoupled energy and power components, all solid state structure, high safety and scalability. Starting with introducing the working principle of this battery, thermodynamics and kinetics, and battery chemistries based on Fe, Mo, and Wo of SOMARB are illustrated. The strategies to improve the performance of Fe-based SOMARB via optimizing RSOFC and ESU are discussed in detail. Finally, several high temperature metal-air batteries derived from SOMARB are introduced. The comparison with other batteries shows that SOMARB is expected to play an important role in future grid and renewable energy storage with concurrent advances in SOFC stack and system design.

Zhang, Cuijuan↗

High Throughput In-Line Coating Metrology Development for Solid Oxide Fuel Cell Manufacturing

Coatings play key roles in solid oxide fuel cell (SOFC) stack durability. For example, diffusion barrier coatings on Cr-containing interconnect and balance of plant (BOP) components protect electrodes from Cr poisoning over the long operational lifetimes (>10,000 hours) of the fuel cell stack. Common defects in coatings, such as cracks, pinholes, and porosity, result in a failure to protect the electrodes, resulting in shorter operational lifetime and thus higher cost. It is very unlikely, even in the best coating process, that all these defects can be mitigated, hence identifying critical defects in parts, and removing defective parts from production before they can damage the stack, becomes paramount. Furthermore, these quality control techniques must be operational in the production/assembly line (in-line), i.e., high throughput and non-destructive, and cost effective. Redox Power Systems, LLC (Redox) together with the National Renewable Energy Laboratory (NREL) developed much needed high throughput, in-line metrology techniques for protective coatings. The overall goal of the project is to lower cost while increasing robustness, reliability, and endurance of SOFC stacks. To accomplish this, we had several objectives, including: to identify key coating and substrate defects that lead to coating failure through the use of detailed characterization methods (e.g., microscopy, XRD, EDS, electrochemistry); to assess capabilities of in-line metrology techniques, e.g., optical profilometry (Redox) and thermography (NREL), to probe these defects, or evidence thereof; demonstrate long-term performance of “defect-free” protective coatings, as identified by in-line metrology, in solid oxide fuel cell (SOFC) stack operation. In the first part of this project, the ability to identify key defects expected to lead to coating and SOFC degradation using in-line metrology tools were evaluated. Coated interconnect samples with controlled defect types and populations were tested under conditions similar to SOFC operation, followed by detailed post-test analysis to reveal the defects responsible for observed degradation. In the second part of the project, the optimal in-line metrology techniques and methodologies were used to map the defect distribution in full-size interconnects with critical defects intentionally allowed to exist in some cases. These interconnects underwent SOFC testing for extended periods (up to ~3,000 hours) followed by post-test analysis to evaluate the effectiveness of in-line metrology techniques in mitigating MCO coating related degradation. Key accomplishments in this project included the following: Demonstrated ASR of < 0.05 ohm-cm 2 at 650 °C for 1,000 hours with low defect (determined by in-line metrology) interconnect samples (average ASR=37 milliohms-cm 2 after over 1,000 hours). Demonstrated that low defect coatings on interconnects (as screened using in-line metrology) have low volatilization of chromium at ~650 °C for 1,000 hours as detected using Cr-getter material (< 5 at% increase above baseline); 1022 hour duration tests under humidified, elevated temperature (750 °C rather than 650 °C) compared a base case against different coating thicknesses. Demonstrated capability to identify initial key defects of interest with in-line metrology techniques using up to 8 cm by 10 cm having coatings with and without intentional defects of interest using thermal imaging and optical profilometry. Correlated key defects identified using metrology techniques with observed coating performance (e.g., ASR and Cr volatility). Conducted several 4 cm by 4 cm cell tests using MCO-interconnects that were pre-screened using some of the metrology techniques developed in the project (e.g., optical profilometry). An analysis of ASR measurements were able to show that defect-free coatings resulted in the anticipated performance in the cell tests.

01 COAL, LIGNITE, AND PEAT↗