SEARCH · Engineering Papers

Results for “slots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS1976

The input admittance of the rectangular cavity-backed slot antenna

The input admittance of the rectangular cavity-backed slot antenna is investigated. The slot is assumed narrow so that the voltage distribution in its aperture is sinusoidal. Equations which represent the input admittance of this slot, backed by a rectangular cavity in which a single propagating wave is assumed to exist, are given. Calculations based on these representations are compared to available measured data. As the depth of the cavity increased the resonant frequency decreased and the bandwidth became narrower. Input admittance curves as a function of electrical slot length are also presented for several size cavities.

Cockrell, C. R.↗

NASA NTRS1977

Downstream influence of swept slot injection in hypersonic turbulent flow

Results of an experimental and numerical investigation of tangential swept slot injection into a thick turbulent boundary layer at Mach 6 are presented. Film cooling effectiveness, skin friction, and flow structure downstream of the swept slot injection were investigated. The data were compared with that for unswept slots, and it was found that cooling effectiveness and skin friction reductions are not significantly affected by sweeping the slot.

Hefner, J. N.↗

NASA NTRS1978

Design and Performance Evaluation of Slotted Walls for Two-Dimensional Wind Tunnels

A procedure for designing slotted walls for two dimensional wind tunnels is is presented. The design objective is the minimization of blockage of streamline curvature or the reduction of both. The slotted wall boundary condition is derived both for flow from the tunnel into the plenum and vice versa, and the procedure for evaluating wall interference is described. A correlation of experimental data for the slotted wall boundary condition is given. Results are given for several designs and evaluations of slotted wind tunnel walls.

Barnwell, R. W.↗

NASA NTRS1980

Supersonic flow development in slotted wind tunnels

The development of test section slot shapes for achieving smooth supersonic Mach number distribution without overexpansion or waviness has, in the past, been largely an experimentally iterative or 'cutand try' procedure for each wind tunnel. To overcome the obvious disadvantages of time and expense involved in such an experimental approach, a simple analytical method has been developed to predict the supersonic flow development in a two-dimensional slotted tunnel given only the variation of open area ratio with downstream distance and the Mach number corresponding to the plenum static pressure. The well known method of characteristics is used with the constraint that it be compatible with the quadratic cross-flow pressure drop boundary condition at the slotted wall. The predicted results from this method agree remarkably well with the experimental calibration data available for some of the existing facilities. The flow mechanism responsible for causing overexpansion in the centerline Mach number distribution with some slot shapes has been brought to light.

Ramaswamy, M. A.↗

NASA NTRS1980

Zero-length, slotted-lip inlet for subsonic military aircraft

Zero-length, slotted-lip inlet performance and associated fan blade stresses were determined during model tests using a 20-inch diameter fan simulator in the NASA-LeRC 9- by 15-foot low-speed wind tunnel. The model configuration variables consisted of inlet contraction ratio, slot width, circumferential extent of slot fillers, and length of a constant area section between the inlet throat and fan face. Inlet configurations having contraction ratios of 1.2 and 1.3 satisfied all critical low-speed inlet operating requirements for a fixed horizontal nacelle and tilt-nacelle-type subsonic V/STOL aircraft, respectively. Relative to a conventional axisymmetric tilt-nacelle inlet, the zero-length, slotted-lip inlet has a 27-percent smaller inlet lip contraction ratio, an 83-percent shorter total length, and a 5-percent smaller maximum cowl diameter.

Glasgow, E. R.↗

NASA NTRS1980

Method and tool for machining a transverse slot about a bore

A method and apparatus for cutting a transverse slot about a bore of smaller diameter than that of the slot are disclosed. The invention consists of introducing a cutting head facing transversely to the bore, through the bore opening its distance from the mill shaft being progressively extended by the addition of spacers between the head and the shaft until the desired slot depth is obtained. The spacers are held in position by a cable passing from the cutting head through the series of spacers and out along the mill shaft. The mill shaft carrying the cutting head is moved transversely into the object wherein the slot is being cut as the object is being rotated thereabout by the mill table to which it is affixed.

David-Malig, M. A.↗

NASA NTRS1981

A simplified model for the viscous crossflow in a slotted test section

A simplified physical model is constructed which simulates the viscous crossflow in a fluid layer near the slots at a fixed streamwise location in a slotted wind tunnel. For low to moderate Reynolds numbers, numerical solutions of the two-dimensional, incompressible Navier-Stokes equations in stream function and vorticity, which govern the model flow, are obtained. Fairly general slot geometry is incorporated by means of the Thompson-Thames-Mastin transformation. An approximate factorization scheme with cyclic acceleration parameters is employed to solve a finite difference analog of the stream function equation. The vorticity equation is numerically solved with a modified version of the classical alternating direction implicit (ADI) scheme. Although no quantitative assessment of solution accuracy can be made, numerical results for variations in incremental wall pressure around the slot are at least qualitatively similar to some experimental results of Berndt and Sorenson.

Cooke, C. H.↗

NASA NTRS1982

Three-dimensional flow studies on a slotted transonic wind tunnel wall

Three-dimensional flow field measurements were made near a transonic slotted wall. Field velocity vectors and static pressure distributions have been obtained. The boundary layer displacement thickness was found to vary in the transverse plane with its maximum at the slot center line but decreased with increasing suction rate through the slot. The boundary layer characteristics were sensitive to the mass transfer through the slot. The projection on the flow field velocity vectors on the transverse plane reveals a vortex-like flow formation. The center of this secondary flow was located nearly at the edge of the wall shear layer and decreased in strength with applied suction. The secondary vortex motion may be attributed to the mean flow skewing, inhomogeneous transverse plane boundary layer and the wall turbulence anisotropy.

Wu, J. M.↗

NASA NTRS1985

Low-speed aerodynamic test of an axisymmetric supersonic inlet with variable cowl slot

The experimental low-speed aerodynamic characteristics of an axisymmetric mixed-compression supersonic inlet with variable cowl slot are described. The model consisted of the NASA P-inlet centerbody and redesigned cowl with variable cowl slot powered by the JT8D single-stage fan simulator and driven by an air turbine. The model was tested in the NASA Lewis Research Center 9- by 15-foot low-speed tunnel at Mach numbers of 0, 0.1, and 0.2 over a range of flows, cowl slot openings, centerbody positions, and angles of attack. The variable cowl slot was effective in minimizing lip separation at high velocity ratios, showed good steady-state and dynamic distortion characteristics, and had good angle-of-attack tolerance.

Powell, A. G.↗

NASA NTRS1985

Mixing layer control for tangential slot injection in turbulent flows

Tangential injection into turbulent flows is one of the most promising methods of minimizing skin friction and providing thermal protection. The technique also has application to laser hardening. The effectiveness of the injected material can be increased if the spreading rate of the resulting mixing region can be reduced. Various techniques which have been shown to be effective in manipulating the rate of growth of mixing layers under certain conditions have been applied to a slot configuration having a thick external turbulent boundary layer. These include geometry modifications to the slot lip trailing edge and acoustic excitation of the slot exit plane over a wide range of frequencies. Neither of these approaches produced any noticeable effect on the downstream evolution of the mixing layer. This lack of effectiveness is attributed to the dominating influence of the well-developed incoming turbulent boundary layer. The placement of large-eddy breakup devices in this boundary layer upstream of the injection point did produce significantly lower velocities in the near-wall region of the flow downstream of the slot exit.

Mcinville, R. M.↗

NASA NTRS1985

Low-speed aerodynamic test of an axisymmetric supersonic inlet with variable cowl slot

Powell, A. G.↗

NASA NTRS1985

Elastic-plastic deformation of a metal-matrix composite coupon with a center slot

A comprehensive experimental analysis of deformations of the surface of a metal-matrix specimen is reported. The specimen is a 6-ply 0 + or - 45 sub s boron-aluminum tensile coupon with a central slot. Moire interferometry is used for high-sensitivity whole-field measurements of in-plane displacements. Normal and shear strains are calculated from displacement gradients. Displacement fields are analyzed at various load levels from 15% to 95% of the failure load. Deformations of the boron fibers could be distinguished from those of the matrix. Highly localized plastic slip zones occur tangent to the ends of the slot. Shear strains and concurrent transverse compressive strains in the slip zones reach approximately 10% and 1%, respectively. Upon unloading, elastic recovery in surrounding regions causes a reverse plastic shear strain in the slip zone of about 4%. Longitudinal normal strains on the unslotted ligament peak at the slot boundary at about 1% strain. The strain concentration factor at the end of the slot decreases with load level and the advance of plasticity.

Post, D.↗

NASA NTRS1985

Numerical study of three-dimensional turbulent flow interactions between blockage models and wind tunnels including longitudinally slotted test sections

A spatial forward-marching approach is applied to compute three-dimensional turbulent flows for several blockage models in free flight, in a solid wall wind tunnel, and in a wind tunnel with longitudinal slots in the test section. The effects of area blockage in the tunnel, model growth and tunnel wall boundary layers, and of the slots are included. The large blockage models are found to have significant wall interference effects which can be reduced by the slots. The effects of the latter are confined to the region near the tunnel wall. Model/wall interference effects are not limited to the effects of area blockage; in particular, boundary layer profile shapes for a wind tunnel model in a tunnel are different from shapes for a model in free flight even when slots are used. This indicates that the flow responds differently in these two cases with the same pressure gradient.

Lin, S.-J.↗

NASA NTRS1988

Theoretical and Experimental Studies of the Transonic Flow Field and Associated Boundary Conditions near a Longitudinally-Slotted Wind-Tunnel Wall

A theoretical examination of the slotted-wall flow field is conducted to determine the appropriate wall pressure drop (or boundary condition) equation. This analysis improves the understanding of the fluid physics of these types of flow fields and helps in evaluating the uncertainties and limitations existing in previous mathematical developments. It is shown that the resulting slotted-wall boundary condition contains contributions from the airfoil-induced streamline curvature and the non-linear, quadratic, slot crossflow in addition to an often neglected linear term which results from viscous shearing in the slot. Existing and newly acquired experimental data are examined in the light of this formulation and theoretical developments.

Everhart, Joel Lee↗

NASA NTRS1987

Analysis of the tapered slot antenna

A method for calculating the radiation pattern of end-fire tapered slot antennas with or without dielectric substrate is presented. The method involves a two-step procedure: (1) determine the field distribution of a traveling wave along the tapered slot, and (2) compute the radiation from this slot field by using the half-plane Green's function to account for termination effects. Acceptable estimates of the slot field usually can be obtained from a stepped approximation to the tapered geometry. The method has been verified by comparisons to measured patterns for various dielectric substrates and antenna dimensions. However, the effect of lateral truncation has not yet been successfully modeled. Experimental patterns showing this effect are presented.

Janaswamy, Ramakrishna↗

NASA NTRS1988

Viscous effects on the resonance of a slotted wind tunnel using finite elements

Prompted by the fact that wind tunnel flutter and oscillatory airload measurements are affected by acoustic vibration mode coupling when the model frequency lies near a wind tunnel resonance frequency, a numerical method has been developed for design sensitivity analysis. Solid curves represent the resonant frequency for the slot, without considering the slot's viscosity. While the viscosity effect decreases with increasing slot width, the viscosity effect also decreases as the slot width approaches zero.

Lee, IN↗

NASA NTRS1988

Gas-jet and tangent-slot film cooling tests of a 12.5 deg cone at Mach number of 6.7

Tests were conducted in the Langley 8-Foot High Temperature Tunnel to determine the aerothermal effects of gaseous nitrogen-coolant ejection on a 3-ft base-diameter, 12.5 degree half-angle cone. Free-stream Mach number, total temperature, and unit Reynolds number per foot were 6.7, 3300 deg R, and 1.4 million, respectively. Two coolant ejection noses were tested, an ogive frustum with a forward-facing 0.8-in radius gas-jet tip, and a 3-in radius hemisphere with a 0.243-in high rearward-facing tangent slot. Data include surface pressures and heating rates, shock shapes, and shock-layer profiles; results are compared with no-cooling data obtained with 1-in and 3-in radius solid noses. Surface pressures were reduced with gas-jet ejection but were affected little by tangent-slot ejection. For both gas-jet and tangent-slot ejection, high coolant flow rates reduced heating even far downstream from the region of ejection; however, low coolant rates caused transition to turbulence and increased heating. Shock-layer profiles of pitot pressure, Mach number, and total temperature were reduced for both gas-jet and tangent-slot ejection. Insight into the gas-jet heat-flux mechanisms was obtained by using shock-layer rake data and established, no-cooling, heat-transfer equations.

Nowak, Robert J.↗

NASA NTRS1990

Sloppy-slotted ALOHA

Random access signaling, which allows slotted packets to spill over into adjacent slots, is investigated. It is shown that sloppy-slotted ALOHA can always provide higher throughput than conventional slotted ALOHA. The degree of improvement depends on the timing error distribution. Throughput performance is presented for Gaussian timing error distributions, modified to include timing error corrections. A general channel capacity lower bound, independent of the specific timing error distribution, is also presented.

Crozier, Stewart N.↗