Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “root chemistry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Vacuum-ultraviolet absorption cross-sections of functionalized four-carbon species

Absorption cross-sections were measured in the vacuum ultraviolet from 5.17 – 9.92 eV using differential absorption spectroscopy for 33 four-carbon species: n-butane, trans-2-butene, cis-2-butene, butanal, butyric acid, ethyloxirane, trans-2,3-dimethyloxirane, cis-2,3-dimethyloxirane, 2-methyloxetane, 2,2'-bioxirane, vinyl oxirane, 3,4-epoxybutan-2-one, diacetyl, diethyl ether, ethyl vinyl ether, vinyl acetate, acetic anhydride, 1-butanol, 3-buten-1-ol, 1–hydroxy-butan-2-one, 1–hydroxy-butan-3-one, 2,3-epoxybutan-1-ol, 3,4-epoxybutan-1-ol, 2-oxetanemethanol, butanone, methyl vinyl ketone, 4H-1,3-dioxine, allyl formate, 2-oxobutanal, 4-hydroxybutanal, 2-methyloxetan-3-one, cis–but-2-en-1-ol, and trans-2–but-enal. Uncertainties were quantified in all cases by accounting for errors in gas-phase concentration, experimental repeatability, and signal-to-noise ratio as a function of photon energy. With the exception of 2-oxobutanal, which is reported with an uncertainty of 10%, convolving the sources of error using the root-sum-square method led to an upper limit of 5% uncertainty above the detection limit, which is largely attributable to chemical purity. Here, the primary objective of the present work is to provide absolute cross-sections along with quantified uncertainty limits. The majority of the absorption spectra, which reflect electronic transitions such as σ → σ* and n → σ*, are reported for the first time and provide insight into fundamental chemical physics, such as vibrational band structure and Rydberg transitions. The quantitative spectra in the present work facilitates the discovery of chemical intermediates that support improvement in the accuracy of computational models for low-temperature combustion and atmospheric chemistry.

biofuels↗
DOE OSTI2025

Molecular Origin of Nanoscale Anion Ordering of LiTFSI Electrolytes Revealed through SAXS/WAXS and Molecular Dynamics Simulations

Recent developments in “water-in-salt” electrolytes have precipitated a renewed effort to study imide-based electrolytes. While previous small-/wide-angle X-ray scattering (SAXS/WAXS) studies have attributed the emergence of a low-Q peak in the SAXS profile of aqueous LiTFSI electrolytes to nanometer-scale anion clustering, a molecular-level understanding of the root of these clusters remains unclear. Here, in this study, we combined molecular dynamics simulations and SAXS/WAXS to study the solvation structures of LiTFSI in acetonitrile, methanol, and water. We concluded that hydrogen bonding in water and MeOH stabilizes anion clusters, while nonpolar methyl groups on methanol and acetonitrile interrupt the nanoscale ordering of TFSI anions. This causes LiTFSI in water and MeOH electrolytes to exhibit two low-Q SAXS profile peaks while LiTFSI in acetonitrile exhibits only a single peak below Q = 1 Å –1 . These findings shed light on the underlying molecular origins of nanoscale anion clusters, which may help in the design of the next generation of electrolyte chemistries.

Trojanowski, Lucas [Univ. of Michigan, Ann Arbor, ↗
DOE OSTI2023

Experimental and Computational Studies of Stress Corrosion Cracking of Alloys 308/309 and 82/182 Weldments in Corrosive and Radiation Environment

The goal of the project was to determine factors that influence SCC and IASCC in weldments found in LWR nuclear power plants. We focused on a SA508-304L SS weldment fabricated by EPRI using gas tungsten arc welding and used an aggressive BWR normal water chemistry (NWC) immersion environment. This weldment used 309L butter and 308L groove filler material. The microstructure of the 309L butter was non-uniform, exhibiting a 20–30μm thick martensitic layer closest to the SA508 interface, a 1–4 mm thick single γ austenite phase dilution zone, and a γ–δ duplex region extending to the 308L groove filler. The 308L groove filler had an entirely γ–δ duplex microstructure. Two approximately 1-inch thick 304L and SA508 plates approximately 12 by 6 square inches were joined using standard nuclear grade welding techniques. This included a post weld heat treatment of the 309L butter after application, a 0.32 cm fit-up root opening, and 57 bead lines of 308L groove filler applied in 18 layers. A 60 degree weld bevel angle was used and the 309L butter was 1.5 cm thick. Displacement cascade damage was induced using proton irradiation at the Michigan Ion Beam Laboratory. The incident proton energy was 2 MeV, the sample temperature was 360 ºC, and the calculated dpa value at 10 μm (60% of the Bragg peak depth of ~18 μm) was 5 dpa using the quick Kinchin-Pease model. Proton irradiation to this damage level required approximately 125 hours of beam time. Two types of samples were irradiated, tensile specimens and TEM bars. Samples were selected from all regions of the weldment, including the SA508-309L butter interface, the 309L-308L interface, and 308L-304L interface. The stainless steel alloys (304L, 308L, and 309L) within the heat affected zone are characterized by a duplex skeletal morphology of δ-ferrite and γ-austenite resulting from the recrystallization associated with weld fabrication. Approximately 7 to 8 mm of length along the specimen was irradiated. The gauge volume surfaces were mechanically polished and then electro-polished to remove mechanical damage from the mechanical polishing step prior to irradiation. Immersion tests were performed in a recirculating autoclave under BWR NWC conditions (2000 ppb wt. dissolved oxygen, neutral pH, 288 ºC, 10 MPa, and inlet water conductivity <100 nS/cm) to accelerate corrosion. Constant strain rate tests were performed either to failure or to approximately 5% strain. Strain rates of 10 -7 to 10 -6 mm/mm/s were used and typical immersion testing required four to six weeks to achieve failure or strains near 5%. Analysis primarily used advanced electron microscopy techniques of FIB lift out specimens.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Effective Local Geometry Descriptor for 29Si NMR Q4 Anisotropy

The nuclear shielding anisotropy, ζ, is a useful nuclear magnetic resonance (NMR) shielding tensor parameter in describing the extent of electron cloud distortion about an atom. Despite the advantages afforded by NMR in structural characterization, the relationship between ζ and local structure of an atom in high-symmetry environments, such as Si-Q 4 sites, is poorly understood. Here, we use a data-driven approach combining random forest feature ranking and the Sure Independence Screening and Sparsifying Operator (SISSO) approach to derive a simple and accurate geometric descriptor for ζ with a root-mean-squared prediction error of 6.77 ppm and an R 2 of 0.761. We then apply this descriptor to describe the local geometric distortion of zeolites Sigma-2 and silica-ZSM-5 whose chemical shift anisotropy tensor has been reported. We envision that this geometric descriptor will allow for structural description and refinement in previously difficult-to-describe materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

On the mechanism of soot nucleation

The mechanism of carbon particulate (soot) inception has been a subject of numerous studies and debates. The article begins with a critical review of prior proposals, proceeds to the analysis of factors enabling the development of a meaningful nucleation flux, and then introduces new ideas that lead to the fulfillment of these requirements. In the new proposal, a rotationally-activated dimer is formed in the collision of an aromatic molecule and an aromatic radical; the two react during the lifetime of the dimer to form a stable, doubly-bonded bridge between them, with the reaction rooted in a five-member ring present on the molecule edge. Several such reactions were examined theoretically and the most promising one generated a measurable nucleation flux. The consistency of the proposed model with known aspects of soot particle nanostructure is discussed. Here, the foundation of the new model is fundamentally the H-Abstraction-Carbon-Addition (HACA) mechanism with the reaction affinity enhanced by rotational excitation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Digital Twin for Chemical Science (DTCS) v0.01

Directly visualizing the trajectories of chemistry can unravel novel insights into the behavior of catalysts, gas phase reactions, photo-induced dynamics, and building blocks for quantum information processing. The ability of explicitly identifying, tracking, and tagging the exchange of matter, hence the annihilation and creation of new chemical species, can be best realized through a close coupling of theory and experiment. While the synchrotron-based characterization facilities propelled rapidly in its hardware, providing higher brightness, better resolution, and more precision, the software infrastructure is lagging. We developed DTCS (Digital Twin for Chemical Science) v.01, a central platform that faithfully mimics advanced instrumentations in Scientific User Facilities, by solving a variety of technical challenges in data acquisition, analysis, and model-driven interpretation. Rooted in physics and accelerated by AI, we validated this concept by direct comparison with precise experimental X-ray Photoelectron Spectroscopy (XPS) observations using a ubiquitous metal-water interfacial scenario, i.e., Ag/H2O as our main narrative. The DTCS v.01 input mirrors how the bench chemists work, with the output directly linked to the end station computer, thereby providing a user-friendly, knowledge-driven, and accessible user experience with mechanistic insights standardized in a way that are ready to be published, versioned, and transferred flexibly.

Qian, Jin↗
DOE OSTI2020

Chemical instability at chalcogenide surfaces impacts chalcopyrite devices well beyond the surface

The electrical and optoelectronic properties of materials are determined by the chemical potentials of their constituents. The relative density of point defects is thus controlled, allowing to craft microstructure, trap densities and doping levels. Here, we show that the chemical potentials of chalcogenide materials near the edge of their existence region are not only determined during growth but also at room temperature by post-processing. In particular, we study the generation of anion vacancies, which are critical defects in chalcogenide semiconductors and topological insulators. The example of CuInSe 2 photovoltaic semiconductor reveals that single phase material crosses the phase boundary and forms surface secondary phases upon oxidation, thereby creating anion vacancies. The arising metastable point defect population explains a common root cause of performance losses. This study shows how selective defect annihilation is attained with tailored chemical treatments that mitigate anion vacancy formation and improve the performance of CuInSe 2 solar cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Dataset for scientific paper "Simulated plant‑mediated oxygen input has strong impacts on fine‑scale porewater biogeochemistry and weak impacts on integrated methane fluxes in coastal wetlands", a modeling study based on field observation at the tidal salt marshes of the Parker River Estuary, Massachusetts, United States

This dataset is the raw and processed data for the paper "Simulated plant ‑ mediated oxygen input has strong impacts on fine ‑ scale porewater biogeochemistry and weak impacts on integrated methane fluxes in coastal wetlands". This study investigated how plant-mediated oxygen input affects subsurface biogeochemical reactions of organic carbon degradation and the resulting methane emissions of coastal wetlands by model simulation. We used the subsurface geochemical simulator PFLOTRAN for the modeling, which produced the simulated changes in porewater chemical substances and methane emissions over 10 days under different scenarios of plant-mediated oxygen input.Specifically, this dataset contains: 1) the input files for PFLOTRAN of all simulation runs conducted in this study. Those files are with an extension of ".in", containing information of the biogeochemical reaction network (stoichiometry, reaction rate, Monod constants, etc), fluid flow rate and oxygen concentration in the fluid which together simulated the plant-mediated oxygen input, the configuration of artificial reactions that simulated the methane fluxes, etc. The PFLOTRAN input files are text files, which can be opened by NotePad, but running these input files will require proper installation of PFLOTRAN (instruction: https://documentation.pflotran.org/user_guide/how_to/installation/installation.html). 2) the raw and processed model output from PFLOTRAN of all simulation runs, and 3) the python scripts used to process the raw model output, including random allocation of root cells, converting raw data into organized formats, calculating the methane fluxes based on the model output, data visualization, etc. The raw and processed model output from PFLOTRAN are in .spydata format, which can be viewed with Python. and 3) the python scripts for data processing and analysis are programming scripts, which can be opened with Python.This modeling work, in particular the model parameterization of root density and initial conditions of porewater concentrations of biogeochemical substances, was based on field measurements at the salt marsh of the Upper Parker River Estuary, Massachusetts, United States.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Irradiation-assisted cracking of SA508-304L weldments with 308L groove filler and 309L butter in hot water immersion constant rate extension tests

Low alloy SA508 bainitic steel is often welded to 300 series austenitic stainless steel in nuclear power plants. These dissimilar metal weldments use 309L butter applied to the low alloy steel and 308L groove filler material to join the 309L to austenite. High alloy steels (such as the 308L and 309L material used here) have been identified as having greater susceptibility to irradiation-assisted stress corrosion cracking (IASCC). Evidence is presented here of cracking under tensile loads in 309L weldment butter in LWR hydrothermal conditions that correlates irradiation induced changes at δ ferrite–γ austenite phase boundaries and γ–γ grain boundaries; specifically intergranular Cr 23 C 6 precipitates. Cracking is not observed in irradiated 308L groove filler under the same conditions. Both the 309L butter and 308L filler material have a duplex or mixed δ–γ phase microstructure due to solidification during the welding procedure. We have performed constant extension rate autoclave immersion tests in BWR normal water chemistry hot water (288 °C, 10 MPa, 2000 wt. ppb dissolved oxygen, <100 nS/cm conductivity, neutral pH) of proton irradiated (2 MeV, approximately 3 displacements per atom at a depth of 10 μm) tensile specimens. Proton irradiation to the dpa levels used here induced Cr 23 C 6 carbide precipitation at γ–γ grain boundaries and δ–γ phase boundaries in the 309L butter but not the 308L filler. Cracking was observed in the proton-irradiated volume of 309L at these interfaces in the vicinity of the Cr 23 C 6 precipitates. We hypothesis the SA508 is the source of carbon in the 309L butter. Cr depletion at γ–γ grain boundaries was also observed and may also be a root cause of cracking. Furthermore, the 309L butter is under significant tensile residual stress in the weldment that adds to applied tensile loads and this too may be a contributing factor.

309L weld butter↗
DOE OSTI2022

Methods for Determining the Infrared Complex Refractive Indices n (λ) and k (λ) from Organic Solid Powders: Comparison of a Sucrose Single Crystal and a Pressed Pellet

There exists a need to measure optical constants n and k for many materials, especially organic solids in the infrared spectral region, but at present, there are only two established methods for making such measurements: single-angle (SA) reflectance and infrared spectroscopic ellipsometry (IRSE). The former derives the n/k vectors via measurement of the change in the amplitude of light reflected from the sample and then uses the Kramers–Kronig transform, while the latter measures the change in polarization of the reflected light from the sample to derive n/k. Here we make a direct comparison between the n/k vectors derived from SA measurements of a sucrose single crystal and the n/k values obtained after the crystal had been crushed, ground to powder, and pressed into a pellet form. The pellet was measured not only by SA but also via the IRSE method, and we found that pressing specular-quality pellets was critical, especially for the SA data. The n/k values of this typical organic molecule all agree to within 0.04 root-mean-square error, confirming that a pressed pellet can be used instead of a crystal to derive the intrinsic n/k vectors. In conclusion, this result is important for the many organic materials that, unlike sugar, do not have centimeter-sized crystals readily available.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Strikingly high amount of tricin-lignin observed from vanilla (Vanilla planifolia) aerial roots

Lignin has attracted tremendous interest as a renewable resource for biofuels, biomaterials, and chemicals especially in the era of bio-based refineries. The structural studies of lignin play an essential role in both understanding the nature and biosynthesis of these polymers and optimizing their valorization values. In this study, we have investigated the structures of lignin from different tissues—aerial roots, nodes, internodes, and seeds, from vanilla (Vanilla planifolia) by using gel permeation chromatography (GPC), heteronuclear single-quantum coherence (HSQC) nuclear magnetic resonance (NMR), and 31P NMR. An unusual tricin-lignin was observed in the aerial roots of vanilla with an strikingly high level of tricin unit, whereas the lignin from the nodes and internodes displayed traditional S/G type lignin with only 4–10% tricin abundance. The aerial roots lignin is primarily composed of β-O-4' alkyl-aryl ether substructures (96% of linkages) in comparison to 65 and 73% in the nodes and internodes lignin, respectively. Additionally, thioacidolysis quantification results showed that lignin from aerial roots has 29.1 mg g -1 tricin, about 3- to 5-fold higher than the lignins isolated from nodes (10.1 mg g -1 ) and internodes (6.9 mg g -1 ). This communication of a particularly high level of tricin-lignin in vanilla plant has important impacts including: (1) the presence of the high amount of tricin as part of lignin from aerial roots could play a vital role for the valorization of lignin, even tricin itself, as a feedstock for value-added chemicals and commodities; and (2) it could open new ways to scientists to design and engineer the structure of tricin-lignin, or lignin in general, to confer plants with new or improved properties due to the plasticity of lignification.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Switching from batch to continuous granulation: A case study of metoprolol succinate ER tablets

Continuous manufacturing (CM) has been used to produce several immediate release drug products. No extended-release (ER) product manufactured employing CM technology has been approved yet. Herein this study investigated the critical aspects of switching from the batch mode of high shear granulation to the continuous operation of twin-screw granulation for extended-release tablets. Metoprolol succinate ER tablets was used as a model ER formulation for this purpose. A central composite design (CCD) was employed to determine the effects of high shear granulator (HSG) parameters, namely impeller speed, granulation time, and binder liquid feeding rate, on the critical granulation characteristics important for product performance. These critical granulation characteristics served as a guide for switching from the batch processing to the continuous operation for achieving the same breaking strength and dissolution for this ER metoprolol tablets. The granulation time was the most critical factor affecting the bulk properties of granules which contributed to tablet dissolution. The higher density and lower compressibility of granules were attained at the longest granulation time of 5.4 min with the fastest liquid feeding rate of 75 g/min. The granules’ density was the primary factor negatively affecting the dissolution of metoprolol tablets. However, the breaking strength of tablets confounded the effect of granules density on metoprolol dissolution. Switching the processing parameters of high shear granulation to twin-screw granulation achieved similar dissolution profiles (F2 greater than 50). The screw speed was not found to affect bulk properties of granules. The root cause of granulation failures in twin-screw granulation, such as premature consolidation, excessive swelling, poor cohesion, inconsistent shearing effects, and formation of deformed agglomerates, were identified. In conclusion, the use of critical granulation characteristics through a performance-based approach of ER tablets facilitated the switching of manufacturing of an ER formulation form batch to continuous operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Active microbial biomass decreases, but microbial growth potential remains similar across soil depth profiles under deeply-vs. shallow-rooted plants

Climate-smart land management practices that replace shallow-rooted annual crop systems with deeply-rooted perennial plants can contribute to soil carbon sequestration. However, deep soil carbon accrual may be influenced by active microbial biomass and their capacity to assimilate fresh carbon at depth. Incorporating active microbial biomass, dormancy, and growth in microbially-explicit models can improve our ability to predict soil's capacity to store carbon. But, so far, the microbial parameters that are needed for such modeling are poorly constrained, especially in deep soil layers. Here, we used a lab incubation experiment and growth kinetics model to estimate how microbial parameters vary along 240 cm of soil depth in profiles under shallow- (soy) and deeply-rooted (switchgrass) plants 11 years after plant cover conversion. We also assessed resource origin and availability (total organic carbon, 14 C, extractable organic carbon, specific UV absorbance of K 2 SO 4 extractable organic C, total nitrogen, total dissolved nitrogen) along the soil profiles to examine associations between soil chemical and biological parameters. Even though root biomass was greater and rooting depth was deeper under switchgrass than soy, resource availability and microbial growth parameters were generally similar between vegetation types. Instead, depth significantly influenced soil chemical and biological parameters. For example, resource availability and total and relative active microbial biomass decreased with soil depth. Decreases in the relative active microbial biomass coincided with increased lag time (response time to external carbon inputs) along the soil profiles. Even at a depth of 210–240 cm, microbial communities were activated to grow by added resources within a day. Maximum specific growth rate decreased to a depth of 90 cm and then remained consistent in deeper layers. Our findings show that >10 years of vegetation and rooting depth changes may not be long enough to alter microbial growth parameters, and suggest that at least a portion of the microbial community in deep soils can grow rapidly in response to added resources. Our study determined microbial growth parameters that can be used in microbially-explicit models to simulate carbon dynamics in deep soil layers.

14C↗
DOE OSTI2026

Jordan–Wigner Transformation for the Description of Strong Correlation in Fermionic Systems

Seniority is a useful way of organizing Hilbert space for strongly correlated systems. The exact zero-seniority wave function, doubly occupied configuration interaction (DOCI), provides accurate results (given the right orbitals) for many strongly correlated electronic systems but has a combinatorial computational cost. In many cases, pair coupled cluster doubles provide a polynomial-cost approximation that closely reproduces the energies of DOCI, but it breaks down in some cases and, as shown herein, it does not provide particularly good density matrices. In this article, we demonstrate that by using the Jordan–Wigner transformation to turn the seniority zero problem back into a Fermionic one, we can provide mean-field variational results of DOCI quality for the Hubbard model and a few small molecular dissociation examples, with polynomial cost, both for the energies and for density matrices, all while being protected from collapse. This success is rooted in the proof we provide, showing that the Hartree–Fock wave function on the Jordan–Wigner-transformed Hamiltonian transforms back to variational coupled cluster doubles in the seniority zero representation, but restricted to have determinant rather than permanent amplitude coefficients, without compromising its overall accuracy.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

Unprecedented generation of 3D heterostructures by mechanochemical disassembly and re-ordering of incommensurate metal chalcogenides

Three-dimensional heterostructures are usually created either by assembling two-dimensional building blocks into hierarchical architectures or using stepwise chemical processes that sequentially deposit individual monolayers. Both approaches suffer from a number of issues, including lack of suitable precursors, limited reproducibility, and poor scalability of the preparation protocols. Therefore, development of alternative methods that enable preparation of heterostructured materials is desired. We create heterostructures with incommensurate arrangements of well-defined building blocks using a synthetic approach that comprises mechanical disassembly and simultaneous reordering of layered transition-metal dichalcogenides, MX 2 , and non-layered monochalcogenides, REX, where M = Ta, Nb, RE = Sm, La, and X = S, Se. We show that the discovered solid-state processes are rooted in stochastic mechanochemical transformations directed by electronic interaction between chemically and structurally dissimilar solids toward atomic-scale ordering, and offer an alternative to conventional heterostructuring. Details of composition–structure–properties relationships in the studied materials are also highlighted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A systematic approach to resolve high impedance of multifunctional energy storage composites

Previous work has proposed and characterized the structural and electrical performance of Multifunctional Energy Storage Composite (MESC) structures: structural elements with embedded lithium-ion batteries which were developed by the Structures and Composite Laboratory (SACL) at Stanford University. This work conducts a comprehensive parametric study over the design variables in the manufacturing process to determine the root cause of increased DC impedance compared to commercial pouch cell batteries. Several MESC samples were assembled under various controlled environmental temperatures and pressures. The samples underwent Hybrid Peak Pulse Characterization (HPPC) to approximate the DC impedance as a function of state of charge (SOC). Failure limits of the battery with respect to assembly temperature and pressure were tested, and an MESC manufacturing simulation model was constructed in Abaqus to validate the manufacturing limits. Samples assembled without enough temperature or pressure failed due to a lack of structural integrity or hermetic seal. Conversely, samples which underwent elevated temperatures and pressures resulted in high DC impedance due to nonuniform electrolyte wetting. This work resolves the primary concern of MESC by achieving comparable DC impedance to commercial pouch cells of the same chemistry and testing procedure.

25 ENERGY STORAGE↗
DOE OSTI2022

Snow Albedo Feedbacks Enhance Snow Impurity-Induced Radiative Forcing in the Sierra Nevada

This study employs a fully coupled meteorology-chemistry-snow model to investigate the impacts of light-absorbing particles (LAPs) on snow darkening in the Sierra Nevada. After comprehensive evaluation with spatially and temporally complete satellite retrievals, the model shows that LAPs in snow reduce snow albedo by 0.013 (0-0.045) in the Sierra Nevada during the ablation season (April-July), producing a midday mean radiative forcing (RF) of 4.5 W m -2 which increases to 15-22 W m -2 in July. LAPs in snow accelerate snow aging processes and reduce snow cover fraction, which doubles the albedo change and radiative forcing caused by LAPs. The impurity-induced snow darkening effects decrease snow water equivalent and snow depth by 20 mm and 70 mm in June in Sierra Nevada bighorn sheep habitat. The earlier snowmelt reduces root zone soil moisture by 20%, deteriorating the forage productivity and playing a negative role in the survival of bighorn sheep.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Photo-Switching of Protein Dynamical Collectivity

We examine changes in the picosecond structural dynamics with irreversible photobleaching of red fluorescent proteins (RFP) mCherry, mOrange2 and TagRFP-T. Measurements of the protein dynamical transition using terahertz time-domain spectroscopy show in all cases an increase in the turn-on temperature in the bleached state. The result is surprising given that there is little change in the protein surface, and thus, the solvent dynamics held responsible for the transition should not change. A spectral analysis of the measurements guided by quasiharmonic calculations of the protein absorbance reveals that indeed the solvent dynamical turn-on temperature is independent of the thermal stability/photostate however the protein dynamical turn-on temperature shifts to higher temperatures. This is the first demonstration of switching the protein dynamical turn-on temperature with protein functional state. The observed shift in protein dynamical turn-on temperature relative to the solvent indicates an increase in the required mobile waters necessary for the protein picosecond motions, that is, these motions are more collective. Melting-point measurements reveal that the photobleached state is more thermally stable, and structural analysis of related RFP’s shows that there is an increase in internal water channels as well as a more uniform atomic root mean squared displacement. These observations are consistent with previous suggestions that water channels form with extended light excitation providing O2 access to the chromophore and subsequent fluorescence loss. We report that these same channels increase internal coupling enhancing thermal stability and collectivity of the picosecond protein motions. The terahertz spectroscopic characterization of the protein and solvent dynamical onsets can be applied generally to measure changes in collectivity of protein motions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗