Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “resistive heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Dissolution of Nb(C,N) and (Ti,V)N in the Coarse-Grained Heat-Affected Zone of Electric Resistance Welded X65 Line Pipe

Nb-rich and Ti/V-rich precipitates were introduced into the X65 linepipe via thermomechanical controlled processing. Their dissolution kinetics were investigated in the coarse-grained heat-affected zone after electric resistance welding. Nb-rich precipitates were found to dissolve completely, whereas Ti/V-rich precipitates were found to dissolve partially, because of slower dissolution kinetics. In conclusion, a complete dissolution of Nb-rich precipitates was associated with significant austenite grain coarsening, which promoted bainite as a quench product, which might have reduced the impact toughness.

microstructure↗

High-temperature Pumping of Silicon for Thermal Energy Grid Storage

As the cost of renewable energy falls below fossil fuels, the key barrier to widespread sustainable electricity has become availability on demand. Energy storage can enable dispatchable renewables, but only with drastic cost reductions compared to current batteries. One electricity storage concept that could enable these cost reductions stores electricity as sensible heat in an extremely hot liquid (>2000 °C) and uses multi-junction photovoltaics (MPV) as a heat engine to convert it back to electricity on demand, hours or days later. This paper follows previously reported technoeconomics and liquid containment, examining equipment that would be needed to exchange heat between resistive heaters, a molten silicon storage tank above 2000 °C, and a heat engine. Herein, we report on a pump that was designed and tested to circulate the liquid silicon between these three regions and the effect of spatial thermal cycling was simulated in models and experiments. While the pump successfully circulated silicon between 1800-2080 °C for ten hours, circulation with a temperature gradient caused it and other non-isothermal experiments to dissolve significantly due to the temperature dependent solubility of not only carbon, but also silicon carbide which otherwise protected the graphite infrastructure. Furthermore, methods to reduce dissolution and an alternative embodiment are presented.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Calorimetry can detect the early onset of hydrolysis in hybrid supercapacitors with aqueous electrolytes

This study investigates the effect of cation species on the onset of electrolyte hydrolysis in hybrid supercapacitors with aqueous electrolytes using isothermal operando calorimetry. The cells consisted of a positive α-MnO 2 cryptomelane electrode and a negative activated carbon (AC) electrode with either 0.5 M K 2 SO 4 or 0.5 M Cs 2 SO 4 aqueous electrolytes. They were characterized using cyclic voltammetry and galvanostatic cycling. In addition, the instantaneous heat generation rate at each electrode was measured using a custom isothermal operando calorimeter. Heat generation associated with resistive losses (Joule heating) and reversible ion adsorption/desorption was clearly identified. For larger potential windows, an endothermic dip, attributed to the onset of hydrolysis, was observed at the positive α-MnO 2 electrode where K + and Cs + ions engaged in fast surface redox reactions. Interestingly, this endothermic dip appeared at 1.8 V and 2.0 V for K 2 SO 4 and Cs 2 SO 4 aqueous electrolytes, respectively. The difference in the stable operating potential window was attributed to thinner solvation shell around Cs + cation than for K + thus reducing the amount of water present near the electrodes as ions partially shed their solvation shells during adsorption. The early onset of hydrolysis could be observed by isothermal operando calorimetry before it could be observed with conventional electrochemical methods.

42 ENGINEERING↗

Measuring the maximum capacity and thermal resistances in phase-change thermal storage devices

Thermal energy storage can increase the efficiency of the electric grid by adding flexibility to thermal systems. The value of thermal storage is a function of its energy and power density, which are driven by the capacity and thermal resistances in the storage device. Measuring these properties in-situ at the device level is an important step to understanding the performance and improving the design of thermal storage systems. Here, we present methods to measure the total capacity and thermal resistances in heat exchangers with integrated phase change materials. These methods are demonstrated on two thermal storage devices - a 570-kWh ice-based storage tank and a 0.35-kWh graphite-tetradecane composite device. The results show how thermal resistances evolve with the state of charge and discharge rate in these devices and quantify the impact of applied pressure on the contact resistance in composite phase change material heat exchangers. The proposed method allows for easy comparison between different systems and provides information on the thermal bottlenecks limiting performance. Ultimately, these measurements will allow designers to make robust, high-performance thermal storage devices for next-generation thermal systems.

25 ENERGY STORAGE↗

An experimentally validated electro-thermal EV battery pack model incorporating cycle-life aging and cell-to-cell variations

Lithium-ion batteries are used in a wide variety of applications. To meet the power and energy demands of these applications battery packs are composed of hundreds to thousands of cells. The electrical and thermal interactions between cells introduce additional complexity in the pack dynamics. To capture these effects, a battery pack model composed of 192 cells based on a first-generation (2012) Nissan Leaf battery pack is developed in MATLAB/Simulink/Simscape. Here, with this model, we simulate the electrical dynamics (using a first-order equivalent-circuit model), the thermal dynamics (using a first-order lumped-parameter thermal model), and the aging dynamics (using a semi-empirical severity factor-based model) of every cell in the pack and we also create a pack thermal model that explicitly captures the heat exchange between the modules, and the cells contained within, during operation. The models are calibrated and validated, both at the cell and pack level, with experimental data. Two different case studies of this pack model are investigated. In the first case study, an initial, normally-distributed, cell-to-cell capacity variation is introduced and its effect on the pack voltage and module temperatures is studied. In the second case study, we deliberately insert cells with lower than nominal capacity into the pack and we investigate how this type of initial cell-to-cell capacity variation affects the pack’s ability to deliver energy over time. Finally, we also study how parallel-connected cells can reduce the effects of cell-to-cell variations at the expense of increased aging of the pack overall.

25 ENERGY STORAGE↗

Postweld Heat Treatment on Toughness of Electric- Resistance Welded X70 Steel

In this report the effect of postweld heat treatment (PWHT) on Charpy V-notch impact toughness of a highfrequency electric-resistance welded (HF-ERW) grade X70 pipeline steel is investigated. PWHT thermal cycles are simulated using the Gleeble on the as-welded specimens. Microstructure, along with crystallographic texture and microhardness, is characterized in specimens that are impact tested at –5°C (23°F), –30°C (–22°F), and –45°C (–49°F). The impact toughness values show a wide scatter band and decrease with the increasing peak temperature of the PWHT. For higher peak temperatures, the microstructure of the heat-affected zone (HAZ) gradually changed from equiaxed ferrite to bainitic ferrite. Furthermore, the prior austenite grain size (PAGS) increases with the increasing peak temperature. The density of high-angle grain boundaries decreases, and the fraction of cleavage planes {100} parallel to the impact fracture plane increases for higher peak temperatures of the PWHT

36 MATERIALS SCIENCE↗

Pressure-Tolerant 3D Anodes Enable Short-Circuit Prevention and Low Heat Generation in Argyrodite Solid-State Batteries

Solid-state batteries (SSBs) offer a safer, higher-energy-density alternative to lithium-ion batteries, yet commercialization is hindered by incompatibility with lithium metal. Here, to overcome these challenges, we developed a cost-effective, commercially available prelithiated micro carbon fiber framework (Li-Cf) anode featuring a high-pressure-tolerance, for use with argyrodite solid-state electrolytes (SSEs). This 3D structure accommodates uniform lithium deposition, simplifies cell assembly under elevated pressure, inhibits dendrite growth toward SSEs, reduces heat generation, and enhances overall compatibility. Notably, our architecture enables the cell to tolerate pressures up to 400 MPa without short-circuiting during assembly. Meanwhile, the 3D framework serves as a preferential pathway for lithium deposition, thereby reducing lithium growth toward the SSEs and mitigating the risk of dendrite formation in SSEs. Operando calorimetry and distribution of relaxation times analysis reveal that lithium morphology degradation at the interface with the SSEs is a key failure mechanism in lithium metal argyrodite SSBs, leading to increased diffusion resistance and heat generation. In contrast, the Li-Cf anode mitigates these issues by reducing both heat flux and charge transfer resistance. Full cells with LiNi 0.8 Co 0.1 Mn 0.1 O 2 /Li 6 PS 5 Cl/Li-Cf retain ~79% capacity after 600 cycles, demonstrating significantly improved cycling stability and strong potential for practical energy storage applications.

25 ENERGY STORAGE↗

A System of Agents for Supporting Optimization and Control of a Connected Community

The residential sector consumes a significant portion of the electricity sold in the United States. Above 60% of the energy used in the sector is used to operate heating, ventilation, and air conditioning (HVAC) systems and water heating (WH) systems. With the increase of intelligence in the grid and the new decision and control options enabled by the Internet of Things; control of these devices can be used to support the grid. Therefore, this article presents a scalable multiagent system for optimizing HVAC and WH systems while maintaining comfort. It allows a utility to orchestrate the shifting of energy from critical periods without direct control, but instead by using a price signal. The architecture, optimization formulation, implementation strategy and results from an implementation project are discussed.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Dual-Responsive Turn-On T 1 Imaging-Guided Mild Photothermia for Precise Apoptotic Cancer Therapy

Apoptosis has gained increasing attention in cancer therapy as an intrinsic signaling pathway, which leads to minimal leakage of waste products from a dying cell to neighboring normal cells. Among various stimuli to trigger apoptosis, mild hyperthermia is attractive but confronts limitations of non-specific heating and acquired resistance from elevated expression of heat shock proteins. Here, a dual-stimulation activated turn-on T 1 imaging-based nanoparticulate system (DAS) is developed for mild photothermia (≈43 °C)-mediated precise apoptotic cancer therapy. In the DAS, a superparamagnetic quencher (ferroferric oxide nanoparticles, Fe 3 O 4 NPs) and a paramagnetic enhancer (Gd-DOTA complexes) are connected via the N6-methyladenine (m 6 A)-caged, Zn 2+ -dependent DNAzyme molecular device. The substrate strand of the DNAzyme contains one segment of Gd-DOTA complex-labeled sequence and another one of HSP70 antisense oligonucleotide. When the DAS is taken up by cancer cells, overexpressed fat mass and obesity-associated protein (FTO) specifically demethylates the m 6</-sup>A group, thereby activating DNAzymes to cleave the substrate strand and simultaneously releasing Gd-DOTA complex-labeled oligonucleotides. The restored T 1 signal from the liberated Gd-DOTA complexes lights up the tumor to guide the location and time of deploying 808 nm laser irradiation. Afterward, locally generated mild photothermia works in concert with HSP70 antisense oligonucleotides to promote apoptosis of tumor cells. This highly integrated design provides an alternative strategy for mild hyperthermia-mediated precise apoptotic cancer therapy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Heat transfer coefficients of moving particle beds from flow-dependent thermal conductivity and near-wall resistance

Accurate determination of heat transfer coefficients for flowing packed particle beds is essential to the design of particle heat exchangers and other thermal and thermochemical equipment. While such dense granular flows mostly fall into the well-known plug-flow regime, the discrete nature of granular materials alters the thermal transport processes in both the near-wall and bulk regions of flowing particle beds from their stationary counterparts. As a result, heat transfer correlations based on the stationary particle bed thermal conductivity could be inadequate for flowing particles in a heat exchanger. Most earlier works have achieved a reasonable agreement with experiments by treating granular heat transfer media as a plug-flow continuum with a near-wall thermal resistance in series. However, the thermal conductivity values of the continuum were often obtained from measurements on stationary beds owing to the difficulty of flowing bed measurements. In this work, it was found that the properties of a stationary bed are highly sensitive to the method of particle packing and there is a decrease in the particle bed thermal conductivity and increase in the near-wall thermal resistance, measured as an effective air gap thickness, on the onset of particle flow. These variations in thermal conductivity of stationary and flowing particle beds can lead to errors in heat transfer coefficient calculations. Therefore, the heat transfer coefficients for granular flows were calculated using experimentally determined flowing particle bed thermal conductivity and near-wall air gap for ceramic particles – CARBO CP 40/100 (mean diameter = 275 µm), HSP 40/70 (404 µm) and HSP 16/30 (956 µm); at velocities of 5–15 mm·s –1 ; and temperatures of 300–650 °C. The thermal conductivity and air gap values for CP 40/100 and HSP 40/70 were further used to calculate heat transfer coefficients across different particle bed temperatures and velocities for different parallel-plate heat exchanger dimensions. Furthermore, these calculations, which show good agreement with measured HTC values reported in literature, can be used as a guide for heat exchanger designs. Graphical abstract

14 SOLAR ENERGY↗

Small-moment antiferromagnetic ordering in single-crystalline La 2 Ni 7

Single crystals of La 2 Ni 7 have been grown out of a binary, La-Ni melt. Temperature dependent, zero magnetic field, specific heat, electrical resistivity, and low field magnetization measurements indicate that there is a series of antiferromagnetic phase transitions at T 1 = 61.0 ± 0.2 K, T 2 = 56.5 ± 0.2 K and T 3 = 42.2 ± 0.2 K. The three specific heat anomalies found at these temperatures qualitatively have very small entropy changes associated with them and the anisotropic M(H) data saturate at ~ 0.12 μ B /Ni; both observations strongly suggesting the AFM order is associated with very small, itinerant, moments. Anisotropic, H ||c and H ⟂c , ρ(H) and M(H) isotherms as well as constant field, ρ(T) and M(T) sweeps manifest signatures of multiple phase lines and result in HT phase diagrams that are clearly anisotropic. Analysis of M(T) and M(H) data allow for the identification of the two lower temperature magnetically ordered states as antiferromagnetically ordered, with the moments aligned along the crystallographic c-axis, and the higher temperature, T 2 < T < T 1 , state as having a finite ferromagnetic component. In addition, the metamagnetic transition at low temperatures, for H applied along the crystallographic c-axis (H ||c ) appears to be a near classic example of a spin-flop transition, resulting in a field stabilized antiferromagnetic state with the moments ordered perpendicular to the c-axis. Finally, although the small moment ordering, and existence of multiple phase transitions in field and temperature, suggesting an energetic proximity of these states, could foretell a degree of pressure sensitivity, our measurements of R(T) for applied pressures up to 2.0 GPa indicate that there is very little pressure dependence of T 1 , T 2 and T 3 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ferromagnetism in Pr-rich binary Pr 7 Ru 3 intermetallic compound

We present the synthesis and experimental characterization of the binary intermetallic compound Pr 7 Ru 3 . The polycrystalline sample was prepared by arc melting pure Pr and Ru, followed by homogenization at 500 °C and 600 °C for 48 and 89 h, respectively. Powder x-ray diffraction confirms that Pr 7 Ru 3 crystallizes in an orthorhombic crystal structure (Pnma, space group no. 62) with the lattice parameters: a = 7.3606(7) Å, b = 23.120(1) Å and c = 6.5959(5) Å. Magnetization, resistivity, and heat capacity measurements reveal a ferromagnetic transition in Pr 7 Ru 3 with the Curie temperature T C ~ 24.5 K. The bulk transition is confirmed by a large λ-shape anomaly observed in the specific heat measurement. The magnetic susceptibility above the transition obeys the modified Curie-Weiss law with a positive Curie-Weiss temperature $\ominus$ CW = 30(1) K and an effective magnetic moment of 3.39(1) μ B /Pr. Resistivity data for Pr 7 Ru 3 reveals metallic-like behavior with a clear anomaly at the transition temperature which is smeared by an applied magnetic field. We also synthesized high-quality nonmagnetic analog La 7 Ru 3 for which superconducting transition is observed with T c = 1.95 K, in agreement with the literature.

36 MATERIALS SCIENCE↗

Conventional superconductivity in single-crystalline BiPt

Binary Bi-Pd/Pt systems have attracted a lot of interest because of their topologically nontrivial nature along with superconductivity. We report the structural and superconducting properties of high-quality single-crystalline BiPt using a comprehensive range of experimental techniques, including X-ray diffraction, electron microscopy, muon spin rotation/relaxation (𝜇⁢SR), magnetization, resistivity, and heat capacity. Our findings establish that BiPt is a weak type-II superconductor with a transition temperature (𝑇 𝑐 ) of 1.2 K which exhibits pronounced anisotropic superconducting characteristics attributed to its hexagonal crystal structure. Magnetization and electronic transport studies reveal that BiPt lies within the dirty limit, while 𝜇⁢SR and heat capacity data indicate conventional 𝑠-wave superconductivity that maintains time-reversal symmetry. Here, this work provides valuable insights into the pairing symmetry and superconducting mechanism of topologically trivial BiPt, a sound comparison system for other Bi-based topologically nontrivial superconductors.

Demagnetization↗

Tuning the flat bands of the kagome metal CoSn with Fe, In, or Ni doping

We report CoSn is a Pauli paramagnet with relatively flat d bands centered about 100 meV below the Fermi energy, E F . Single crystals of CoSn lightly doped with Fe, In, or Ni are investigated using x-ray and neutron scattering, magnetic susceptibility and magnetization, AC susceptibility, specific heat, and resistivity measurements. Within the rigid-band approximation, hole doping with a few percent of Fe or In should move the flat bands closer to E F , whereas electron doping with Ni should move the flat bands further away from E F . We provide evidence that this indeed occurs. Fe and In doping drive CoSn toward magnetism, while Ni doping suppresses CoSn's already weak magnetic response. The resulting ground state is different for Fe versus In doping. For Fe-doped crystals, Co 1-x Fe x Sn, with 0.02< x <0.27, the magnetic and specific-heat data are consistent with the formation of a spin glass, with a glass temperature, T g , ranging from 1 K for x = 0.02 to 10 K for x = 0.27. Powder and single-crystal neutron diffraction found no evidence of long-range magnetic order below T g for samples with x ≈ 0.17. For In-doped crystals, CoSn 1-y In y , both the magnetic susceptibility and the Sommerfeld coefficient, γ, increase substantially relative to pure CoSn, but with no clear indication of a magnetic transition for 0.05< y <0.2. CoSn crystals doped with Ni (Co 0.93 Ni 0.07 Sn) have a significantly smaller magnetic susceptibility and γ than pure CoSn, consistent with flat bands further from E F .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Synthesis, Structures, and Transport Properties of Quaternary Ba–Ag– Tr –As Materials ( Tr = Ga, In)

The synthesis, structures, and properties of two quaternary barium–arsenide materials are presented. The first, Ba 4 Ag 2.3 In 1.7 As 8 , is a novel material with the monoclinic unit cell ( P 2 1 / m space group). The layered crystal structure of Ba 4 Ag 2.3 In 1.7 As 8 may be considered a lower‐symmetry, distorted analog of the LaCuSb 2 structure. The structure features a rare As fragment, cis‐trans As chains along the [010] direction. Large crystals of Ba 4 Ag 2.3 In 1.7 As 8 can be grown from Bi flux and are used for subsequent transport property measurements. Electrical resistivity and heat capacity properties are reported, establishing Ba 4 Ag 2.3 In 1.7 As 8 as a metallic phase. The second material, Ba 4 AgGa 5 As 8 , is a 3D material that crystallizes in the orthorhombic unit cell (noncentrosymmetric and polar Iba 2 space group). Expanding upon its original discovery, the optimized synthetic profile for single‐phase polycrystalline samples as well as transport properties relevant to thermoelectric applications are presented. Ba 4 AgGa 5 As 8 exhibits a high Seebeck coefficient of 290 μV K −1 at room temperature, indicative of lower carrier concentrations typical for nonmetallic phases. Electrical resistivity measurements also affirm conventional semiconducting behavior for Ba 4 AgGa 5 As 8 .

Kyveryga, Victoria [Department of Chemistry Iowa S↗

Pressure drop and heat transfer characteristics of nitrate salt and supercritical CO 2 in a diffusion-bonded heat exchanger

A lab-scale 316/L stainless steel diffusion-bonded heat exchanger was examined within a coupled high-temperature test facility consisting of an atmospheric-pressure nitrate salt loop and a supercritical carbon dioxide (sCO 2 ) loop operating between 10 and 16 MPa. Pressure loss measurements collected for flow rates up to 0.55 kg/s of Solar Salt and up to 0.6 kg/s of carbon dioxide were used to generate friction factor correlations for the respective circular and semicircular zig-zag flow passages. Heat transfer measurements were also performed over a wide range of conditions to produce Nusselt correlations for the CO 2 and nitrate salt geometries. The Nusselt number is deduced from a heat transfer resistance network and overall conductance measurements collected across the operating envelope of the coupled sCO 2 – nitrate salt test facility. The CO 2 side correlation showed excellent agreement with existing correlations in the literature. Further, the salt side, having nearly circular channels with a different zig-zag angle and hydraulic diameter, yielded a new correlation applicable to the laminar flow regime. To examine the similitude of the friction correlations, pressure drop testing with water was performed on both sides of the component as well. Finally, results from non-destructive examination are discussed to provide insights regarding inspection methods and draining performance of high-temperature liquids in compact heat exchangers.

36 MATERIALS SCIENCE↗

Creep-Resistant Ferritic-Martensitic Steels for Power Plant Applications

Creep-resistant ferritic-martensitic steels are essential materials used in power plants for electricity generation. The efficiency and emissions of the plant are closely related to the operating temperature. Materials used in the hottest sections are one of the main limiting factor for plant operation at 650 °C. This review describes the recent development of creep-resistant ferritic-martensitic steels from a large dataset of in-house research. The findings are tied to available literature for discussion. A first steel, CPJ-7, was developed with an operating temperature approaching 650 °C, and a refined design, JMP, showed the potential to operate at 650 °C. Approximately fifty different ingots, each weighing ~ 7 kg, were vacuum induction melted and processed. Overall, wrought and cast versions of CPJ-7 present superior creep properties when compared to wrought and cast versions of COST alloys for steam turbine and P91/92 for boiler applications. The prolonged creep life was attributed to slowing down the process of the destabilization of the MX and M 23 C 6 precipitates at 650 °C. The cast version of CPJ-7 also revealed superior mechanical performance, above commercially available cast 9% Cr martensitic steel or derivatives. Following the work on CPJ-7, the JMP steels were designed with higher Co for increased solid solution strengthening, Si for oxidation resistance and increased W for matrix strength and stability. The JMP steels showed increases in creep life compared to CPJ-7 between 118 and 150% at 650 °C for testing at various stresses between 138 and 207 MPa. On a Larson–Miller plot, the performance of the JMP steels surpasses that of state-of-the-art MARBN steel. The influence of various elements within the composition of the alloys on the microstructure and mechanical properties is discussed. This review presents approximately 420,000 h of in-house creep testing, the equivalent of almost 50 years of cumulative creep tests.

36 MATERIALS SCIENCE↗