Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “recrystallization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Evaluation of the Effect of Burnup Acceleration on UO 2 Microstructure Evolution

Accelerated fuel qualification (AFQ) is a methodology by which new nuclear fuels are developed in an accelerated time frame compared with historical fuel qualification approaches. AFQ generally relies on high-fidelity physics-based modeling and simulation tools to adequately describe fuel performance as well as on revolutionary methods to accelerate burnup accumulation and collect relevant data more quickly. This report summarizes the use of advanced fuel modeling and simulation tools to evaluate microstructures from commercially irradiated fuel and microstructures from proposed MiniFuel irradiations, in which burnup accumulation is accelerated while prototypic temperature conditions are maintained. In this milestone, we used the mesoscale fuel performance code MARMOT to model the evolution of irradiated UO 2 microstructures and their potential restructuring at high burnup. The simulation conditions were informed by BISON models of both commercially irradiated fuel and MiniFuel. A first set of simulations investigated the recrystallization behavior of fully dense microstructures and showed full recrystallization at burnups as low as 52 MWd/kgU at 950°C. However, these simulations did not account for the presence of fission gas bubbles (predicted by BISON). Therefore, a second set of simulations including fission gas bubbles was performed and indicated that at the lowest temperature considered (650°C), the porous UO 2 microstructures have the highest total Gibbs free energies and are likely to recrystallize earlier than higher temperature cases (800 and 950°C), which agrees with high-burnup fuel characterization data. The results also showed that at lower temperature (650°C), the total free energies of the PWR fuel and MiniFuel microstructures are not significantly different. However, at the highest temperature (950°C), MiniFuel microstructures have a lower free energy than that of the PWR fuel microstructure. The competing effects between the temperature-dependent grain nucleation rate and the reduction of the free energy of the microstructure at higher temperature as a result of diffusion indicated that restructuring may occur at even higher temperatures than those considered in this study. In addition to the microstructure evolution modeling efforts, the burnup gradient across a single fuel specimen was also considered. This evaluation was for the VXF-15 position of the High Flux Isotope Reactor (HFIR) using the code suite HFIRCON, which was developed to automate the workflow for evaluating targets and fuel as they are irradiated in HFIR. The burnup gradient evaluation showed a dependence on both the axial and radial locations within the specimen, with a maximum difference of 1.7 between the inner and outermost radial layers. This relationship was further supported by considering the fission product speciation with respect to location within the specimen, which showed a higher concentration of 239 Pu, 240 Pu, and 241 Pu on the outer radial locations of the specimen than the center. The findings of the burnup and speciation evaluation show that some amount of self-shielding is occurring in the specimen when irradiated in the high-flux environment of HFIR; however, this impact is more pronounced for natural uranium when compared to 6% enrichment due to the higher ratio of 238 U in the specimen. Further analyses are required to understand the sensitivity of this gradient to spatial mesh and enrichment of the specimen.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Beyond Magic Barrels: Digital manufacturing for crystallization, process development and optimization of explosive materials: Part II Resveratrol Exemplar

This SAND report summarizes work supported by an Engineering Sciences Research Foundation (ESRF) Lab Directed Research and Development (LDRD) project entitled “Beyond Magic Barrels: Digital manufacturing for crystallization, process development and optimization of explosive materials.” This SAND report is written in two parts with Part 1 discusses recrystallization of our explosive exemplar and Part 2 summarizing our work with recrystallization of resveratrol. We have studied resveratrol recrystallization with a multiscale approach combining experiments, modeling and simulation. At the single crystal scale, microscopy experiments illuminate crystal time-dependent growth rates using advanced image analysis. Bench scale experiments were carried out to look at growth of multiple particles in a small reactor creating thousands of particles and analyzing the results with microscopy and μCT. For the modeling we combine kinetic Monte Carlo (kMC) models with subscale information from density functional theory (DFT) or molecular dynamics. This work is discussed in Part 1 and can also be found in a paper from the project discussing a coarse-grained kMC model specifically developed for resveratrol. For well-mixed systems, we have population balance equations (PBE) linked with species mass conservation forming a set of ordinary differential equations that can be solved quickly. For more complicated geometries, such as the vat crystallization used throughout the complex, a coupled computational fluid dynamic (CFD)/PBE method was developed to account for gradients in temperature and concentration and differences in crystallization rates throughout the domain. These simulations are more complex and require high performance computing. We present results for two cases: 5% seed fast cool with parameters fit to the well-mixed case and 5% seed slow cool using the same parameters. We show reasonable agreement with experiments though are particles are significantly larger than the experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Laser Powder Bed Fusion Manufactured Alloys 625 and 282 and Properties Relevant to Advanced Nuclear Components

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Large printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. Annealing at 1,180°C for 1 h followed by 4 h at 800°C in a high density of 50 nm γ′-strengthening precipitates as well as partial recrystallization resulted in a bimodal grain distribution. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Printing defects were the likely reason for the lower creep performance of LPBF 282 and could be suppressed by optimizing the build configuration. Printing 625 on an EOS M290 machine using the recommended EOS parameters resulted in a very low defect density. Superior creep strength at 725°C was observed for the as-printed LPBF 625 along the build direction when compared with wrought 625. No defect larger than ~50 µm could be detected by X-ray computed tomography in the as-printed conditions and after creep testing for 1,000 h at 725°C and 150 MPa. Small, needle-like δ-phase precipitates were observed after creep testing for 100 h at 725°C and 200 MPa. The rapid formation of the γ phase is directly related to the initial Nb and Mo segregation in the LPBF 625 cell walls, and its effect on the alloy’s high-temperature performance will be evaluated. Solution annealing was carried out at 1,150°C for 1 h and led to full recrystallization of the alloy. A decrease in strength and increase in ductility were observed after solution annealing, and the alloy recrystallization resulted in isotropic tensile properties at room temperature, contrary to what was observed for the as-printed LPBF 625.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Fossil Corals With Various Degrees of Preservation Can Retain Information About Biomineralization-Related Organic Material

Scleractinian corals typically form a robust calcium carbonate skeleton beneath their living tissue. This skeleton, through its trace element composition and isotope ratios, may record environmental conditions of water surrounding the coral animal. While bulk unrecrystallized aragonite coral skeletons can be used to reconstruct past ocean conditions, corals that have undergone significant diagenesis have altered geochemical signatures and are typically assumed to retain insufficient meaningful information for bulk or macrostructural analysis. However, partially recrystallized skeletons may retain organic molecular components of the skeletal organic matrix (SOM), which is secreted by the animal and directs aspects of the biomineralization process. Some SOM proteins can be retained in fossil corals and can potentially provide past oceanographic, ecological, and indirect genetic information. Here, we describe a dataset of scleractinian coral skeletons, aged from modern to Cretaceous plus a Carboniferous rugosan, characterized for their crystallography, trace element composition, and amino acid compositions. We show that some specimens that are partially recrystallized to calcite yield potentially useful biochemical information whereas complete recrystalization or silicification leads to significant alteration or loss of the SOM fraction. Our analysis is informative to biochemical-paleoceanographers as it suggests that previously discounted partially recrystallized coral skeletons may indeed still be useful at the microstructural level.

58 GEOSCIENCES↗
NASA NTRS1962

INVESTIGATION OF MECHANICAL PROPERTIES OF CHROMIUM, CHROMIUMRHENIUM, AND DERIVED ALLOYS

Tensile tests of iodide chromium have been carried out over the range 0 C to 400 C. The peaks which have been detected in the variation of yield stress with temperature are quite small and difficult to locate exactly. However, by dint of performing many tests at close temperature intervals, the peaks have been located as well as seems possible at this time. During this series of tests, it was found, contrary to previous experience, that recrystallized material which had been prestrained about 8 per cent and then recrystallized again was more ductile than recrystallized material which had not had such a treatment. The slow tensile transition temperature was depressed below room temperature, but was above 0 C.

PURIFICATION↗
NASA NTRS1972

Abnormal grain growth in TD-nickel.

Characteristics of the coarse grain transformation occurring in TD-nickel 1 in. bar under certain conditions of deformation and annealing were examined. The transformation exhibits Avrami-type kinetics, with an activation energy of 250 kcal per mole. Characteristics of untransformed regions are like those of the as-received state. The transformed grain size increases with increasing deformation and decreasing annealing temperature. The coarse grain transformation is significantly different from primary recrystallization in pure nickel. Its characteristics cannot be rationalized in terms of primary recrystallization concepts, but may be explained in terms of an abnormal grain growth description. The coarse grain transformation in TD-nickel is abnormal grain growth rather than primary recrystallization. The analysis suggests an explanation for the effect of thermomechanical history on the deformation and annealing behavior of TD-nickel.

Petrovic, J. J.↗
NASA NTRS1973

Artificial meteor ablation studies: Olivine

Artificial meteor ablation was performed on a Mg-rich olivine sample using an arc-heated plasma of ionized air. Experimental conditions simulated a meteor traveling about 12 km/sec at an altitude of 70 km. The mineral content of the original olivine sample was 98% olivine (including traces of olivine alteration products) and 2% chromite. Forsterite content of the original olivine was Fo-89. After ablation, the forsterite content had increased to Fo-94 in the recrystallized olivine. In addition, lamella-like intergrowths of magnetite were prevalent constituents. Wherever magnetite occurred, there was an increase in Mg and a corresponding decrease in Fe for the recrystallized olivine. The Allende fusion crust consisted of a recrystallized olivine, which was more Mg-rich and Fe-deficient than the original meteorite's olivine, and abundant magnetite grains. Although troilite and pentlandite were the common opaque mineral constituents in this meteorite, magnetite was the principal opaque mineral found in the fusion crust.

Blanchard, M. B.↗
NASA NTRS1973

Electron petrography of Apollo 14 and 15 breccias and shock-produced analogs

Six lunar breccias were studied in detail by optical and transmission electron microscopy and separated into two classes on the basis of presence or absence of recovery and recrystallization textures: Class A breccias with no recrystallization include samples 14063, 14301, and 15498; Class B breccias with recrystallization include samples 14321, 15455, and 15418. Samples of Apollo 16 soil (65010) experimentally shocked to 50, 100, and 250 kilobars pressure were sectioned and studied for comparison with the breccias. It is concluded that the Class A breccias were formed from unconsolidated lunar regolith by deformation due to shock waves of a few tens of kilobars. The Class B breccias could also have been produced from unconsolidated material at higher shock stresses, the annealing being achieved by the heating resulting from the shock deformation.

Christie, J. M.↗
NASA NTRS1974

Artificial meteor ablation studies - Olivine

Artificial meteor ablation has been performed on a Mg-rich olivine sample by means of an arc-heated plasma of ionized air. Experimental conditions simulated a meteor traveling about 12 km/sec at an altitude of 70 km. The mineral content of the original olivine was 98% olivine (including traces of olivine alteration products) and 2% chromite. The forsterite content of the original olivine was Fo 89 and increased to Fo 94 in the recrystallized olivine after ablation. In addition, lamella-like intergrowths of magnetite were prevalent. Wherever magnetite occurred, Mg increased and Fe decreased in the recrystallized olivine. The Fe for the magnetite exsolved from the original olivine crystals. Individual particles (i.e., spherules) were also characterized by magnetite intergrowths. Fusion crusts on the Allende and Murchison meteorites were compared with the fusion crust on the olivine sample. The Allende fusion crust consisted of a recrystallized olivine, richer in Mg and deficient in Fe in comparison with the original meteorite's olivine, and abundant magnetite grains.

Blanchard, M. B.↗
NASA NTRS1978

Hot forming of silicon sheet, silicon sheet growth development for the large area silicon sheet task of the low cost silicon solar array project

The hot workability of polycrystalline silicon was studied. Uniaxail stress-strain curves are given for strain rates in the range of .0001 to .1/sec and temperatures from 1100 to 1380 C. At the highest strain rates at 1380 C axial strains in excess of 20% were easily obtainable without cracking. After deformations of 36%, recrystallization was completed within 0.1 hr at 1380 C. When the recrystallization was complete, there was still a small volume fraction of unrecyrstallized material which appeared very stable and may degrade the electronic properties of the bulk materials. Texture measurements showed that the as-produced vapor deposited polycrystalline rods have a 110 fiber texture with the 110 direction parallel to the growth direction and no preferred orientation about this axis. Upon axial compression perpendicular to the growth direction, the former 110 fiber axis changed to 111 and the compression axis became 110 . Recrystallization changed the texture to 110 along the former fiber axis and to 100 along the compression axis.

Graham, C. D., Jr.↗
NASA NTRS1978

Progress towards high efficiency polycrystalline thin-film GaAs AMOS solar cells

Results of Ge film recrystallization using focused laser beams and GaAs film growth on such layers in the making of high efficiency thin-film AMOS solar cells are discussed. Since a conversion efficiency of 14% was obtained for an AMOS cell fabricated on sliced bulk polycrystalline GaAs, high efficiency cells are being developed by chemically vapor-depositing GaAs films on previously recrystallized evaporated Ge films to minimize the grain boundary (GB) effects. Schottky barrier solar cells made on sliced polycrystalline GaAs wafers were studied to investigate the effects of grain boundaries on cell properties and the potential efficiency of GaAs thin-film cells. Ge film recrystallization and the chemical vapor deposition (CVD) of the 2 to 3 micron thick GaAs films are described. AMOS solar cells with 100 Angstrom thick Ag metallization were made on CVD GaAs/recrystallized Ge/W substrates with an energy conversion efficiency of 8%.

Yeh, Y. C. M.↗
NASA NTRS1982

Holographic fabrication of gratings in metal substrates

A program for investigating the grain enlargement resulting from the laser recrystallization of a thin gallium arsenide film on a patterned substrate, a technique known as graphoepitaxy was evaluated. More specifically, the effects of recrystallizing an uncapped gallium arsenide film using a continuous wave neodymium YAG laser operating at 1.06 microns were studied. In an effort to minimize arsenic loss from the film, the specimens were held in an arsine atmosphere during recrystallization. Two methods for fabricating patterned substrates were developed, one using reactive ion etching of a molybdenum film on both sapphire and silicon substates and another by preferential wet etching of a silicon substrate onto which a film of molybdenum was subsequently deposited.

Fletcher, R. M.↗
NASA NTRS1985

Diffusion welding of MA 6000 and a conventional nickel-base superalloy

A feasibility study of diffusion welding the oxide dispersion strengthened (ODS) alloy MA 6000 to itself and to conventional Ni-base superalloy Udimet 700 was conducted. Butt joints between MA 6000 pieces and lap joints between Udimet 700 and the ODS alloy were produced by hot pressing for 1.25 hr at temperatures ranging from 1000 to 1200 C (1832-2192 F) in vacuum. Following pressing, all weldments were heat treated and machined into mechanical property test specimens. While three different combinations of recrystallized and unrecrystallized MA 6000 butt joints were produced, the unrecrystallized to unrecrystallized joint was most successful as determined by mechanical properties and microstructural examination. Failure to weld the recrystallized material probably related to a lack of adequate deformation at the weld interface. While recrystallized MA 6000 could be diffusion welded to Udimet 700 in places, complete welding over the entire lap joint was not achieved, again due to the lack of sufficient deformation at the faying surfaces. Several methods are proposed to promote the intimate contact necessary for diffusion welding MA 6000 to itself and to superalloys.

Moore, T. J.↗
NASA NTRS1986

Petrology and classification of the Garraf, Spain chondrite

Microscopic and electron microprobe studies indicate that the Garraf meteorite is a highly-recrystallized chondrite of petrologic type 6. Olivine (Fa24.7; PMD 1.1) and low-Ca pyroxene (Fs20.9; PMD 1.1) compositions indicate that it belongs to the L-group. Based on contents of noble gases, pervasive fracturing of silicates, common undulose extinction of olivine and plagioclase, and the lack of melt pockets and maskelynite, Garraf is placed into shock facies b. It is concluded that Garraf is a highly recrystallized L6b chondrite that, after recrystallization, was cataclased and comminuted by shock.

Keil, K.↗
NASA NTRS1987

Cellular monotectic model solidification

Succinonitrile (sn) was purified to a superior level using a fractional recrystallization method. The melting point of the best twice recrystallized sn was not raised by following with double distillation. This was tested using differential scanning calorimetry. The peak shape on melting also proved that double distillation after double recrystallization did not improve the quality. Stability and phase diagrams for succinonitrile and glycerol are presented.

Kaukler, William F.↗
DOE OSTI2025

In situ irradiation of spent nuclear fuels

To improve the economics of commercial nuclear reactors, nuclear vendors and utilities are seeking approval for increased burnup usage of the existing nuclear fleet. This is especially critical for meeting the clean energy initiative by the United States Government, Department of Energy (DOE). However, one of the key challenges the nuclear industry faces in this regard is that the regions exposed to high burnup and low temperatures exhibit a fine-grained microstructure with large bubbles known as high-burnup structure (HBS) [1]. The formation of HBS has been correlated to the diminished performance of the reactor, as well as fuel fragmentation and pulverization during transient and accidental conditions [2]. Therefore, it is paramount to understand the mechanisms for HBS formation along with its impact on the properties and performance of nuclear fuels. While existing programs, such as Nuclear Energy Advanced Modeling and Simulation (NEAMS) and Advanced Fuel Campaign (AFC) are focusing on evaluating the performance impact of HBS, the physical mechanisms contributing to HBS formation are still not fully understood. In addition, having predictive capabilities and sound understanding of the microstructural evolution of nuclear fuel is essential for accelerated development, qualification, and deployment of new nuclear materials and novel reactor designs for advanced nuclear reactors. There is a lack of consensus among researchers regarding the mechanisms leading to such restructuring observed in HBS. Grain subdivision due to polygonization versus recrystallization, continuous versus discrete recrystallization occurring in tandem or conjunction, etc., have been proposed and debated. In general, it is hypothesized that defect accumulation and dislocation interaction within the grains cause the realignment of dislocations into grain boundaries, leading to the new subgrain formation, which over time transforms into new grains. However, due to the lack of transient data, the importance of fission rate, irradiation, thermal, and stress history of the fuel on the restructuring could not be assessed. In situ microstructural evolution under various irradiation conditions is desired to bridge this gap. Alternatively, phase-field-based models have been developed to capture HBS formation via discrete recrystallization utilizing the classical nucleation approach [3–5]. However, in these models, the grain nucleation criteria are often defined based on empirical relations for burnup and fission gas density leading to dislocation density change. A mechanistic approach to capture the dislocation interaction with the microstructural features leading to grain subdivision is lacking.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Coupling Thermomechanical Processing and Alloy Design to Improve Textures in Mg-Zn-Ca Sheet Alloys

Abstract The effect of Ca and Zn additions on the microstructure and texture evolution during thermomechanical processing of Mg-Zn-Ca sheet alloys was systematically investigated and quantified. Plane strain compression testing in a Gleeble thermomechanical simulator was used to physically simulate a 10-pass rolling schedule, while allowing for careful control and monitoring of the processing parameters. Textures in the as-deformed ternary alloy samples demonstrate a weak maximum basal intensity and spreading in the transverse direction. Increasing the Zn content to 3.2 wt.% in the ternary alloys resulted in samples that exhibited weak textures in the as-deformed state. Importantly, static recrystallization (SRX) during post-deformation annealing of these alloys promoted a desirable annular texture, with the c -axis tipped from the normal direction and a lower basal texture intensity. The evolution in texture during SRX is associated with as-deformed microstructures with broad grain orientation spreads and a low degree of recrystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructure and hardness evolution induced by annealing of ion irradiated LiTaO 3

We report the evolution of the microstructure and mechanical properties of low-energy heavy-ion-irradiated LiTaO 3 crystals annealed at various temperatures was investigated by transmission electron microscopy (TEM) observations and nanoindentation tests to extend the applications of irradiated LiTaO 3 crystals. Before annealing, randomly distributed voids formed in an approximately 200 nm thick region at the end of the ion irradiation range, which was attributed to preferential absorption of interstitials by the amorphous-crystalline interface. After annealing, a new directional diffusion path of defects was identified, resulting in a void string. Furthermore, void string diffusion to the free surface was also found during the annealing temperature increase process, which offers a potential application in designing custom sized-thickness exfoliation at the nanoscale. Meanwhile, two competing processes were identified during the annealing process: epitaxial recrystallization from the amorphous-crystalline interface and grain nucleation process in the amorphous region, which formed phases different from the matrix crystal structure, resulting in an interaction between them. Furthermore, the hardness of irradiated samples was also found to be affected by the annealing process; in particular, a hardness decrease induced by the interstitial Fe ions in the recrystallized region was also confirmed, which can improve the processability of samples for further application.

36 MATERIALS SCIENCE↗