Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer melts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Effects of Polymer Morphology on Solvent and Catalyst Accessibility during Polyethylene and Polystyrene Autoxidation

Efficient catalytic deconstruction of plastics requires facile solvent and catalyst access to polymer substrates to minimize mass transfer effects. Autoxidation using Co(II) acetate, Mn(II) acetate, and a radical carrier in acetic acid is a promising strategy to deconstruct mixed plastic waste, yet the role of polymer morphology in governing solvent and catalyst accessibility remains poorly understood. Here, in situ simultaneous small- and wide-angle X-ray scattering (SAXS/WAXS), complemented by X-ray fluorescence (XRF) imaging and high-pressure differential scanning calorimetry (DSC), were used to elucidate interactions between acetic acid, a Co/Mn catalyst solution, and semicrystalline polyethylene (PE) and amorphous polystyrene (PS) from room temperature to 160 °C. In PE, acetic acid and catalyst access were confined to amorphous regions and cryomilled particle interfaces at room temperature, while crystalline lamellae remained intact after soaking for up to 34 h. Increasing temperature enabled solvent uptake into PE, followed by solvent-assisted softening above 100 °C, and a modest melting-point depression that removed lamellar transport barriers upon melting. Conversely for PS, acetic acid penetrated the glassy polymer without inducing chain mobility until the glass transition was reached, above which the observed structural changes were consistent with enhanced segmental mobility which enabled bulk penetration. These results suggest that polymer morphology and thermally activated physical transitions arising from diffusion and polymer–solvent interactions can influence whether autoxidation of plastics is transport-limited or kinetically controlled, providing a framework for aligning reaction conditions with reaction outcomes.

09 BIOMASS FUELS↗
DOE OSTI2026

Tunable PA6 Polymer System for Thermoplastic Reinforced Body Panels

Project Goal: Overall, a redesigned polyamide system will combine the ductility and processing of a PA6 matrix, the strength and modulus of CF, and the facile recyclability of esters. Approach: PEA can be synthesized under conventional, industrially relevant pathways. Material properties and processing will be analyzed and compared to commercial PA6 material. Results: Polycondensation, traditional for polyesters, was successful in synthesized a PEA. PEA exhibited fast crystallization and bimodal melting behavior suggesting beneficial crystallization kinetics. PEA exhibit reduced melting temperatures owed to the incorporation of ester units in the polymer structure.

42 ENGINEERING↗
DOE OSTI2023

Bead–Spring Simulation of Ionomer Melts—Studying the Effects of Chain-Length and Associating Group Fraction on Equilibrium Structure and Extensional Flow Behavior

Ionomers are associative polymers with diverse applications ranging from selective membranes and high-performance adhesives to abrasion- and chemical-resistant coatings, insulation layers, vacuum packaging, and foamed sheets. Within equilibrium melt, the ionic or associating groups are known to form thermally reversible, associative clusters whose presence can significantly affect the system’s mechanical, viscoelastic, and transport properties. It is, thus, of great interest to understand how to control such clusters’ size distribution, shape, and stability through the designed choice of polymer architecture and the ionic groups’ fraction, arrangement, and interaction strength. In this work, we represent linear associating polymers using a Kremer–Grest type bead–spring model and perform large-scale MD simulations to explore the effect of polymer chain-length (l) and fraction (f s ) of randomly placed associating groups on the size distribution and stability of formed clusters. We consider different chain-lengths (below and above entanglement), varying fractions of associating groups (represented by ‘sticky’ beads) between 5 and 20%, and a fixed sticky–sticky nonbond interaction strength of four times that between regular non-associating beads. For all melts containing associating groups the equilibrium structure factor S(q) displays a signature ionomer peak at low wave vector q whose intensity increases with increasing f s and l. The average cluster size Nc increases with f s . However, the effect of chain-length on Nc appears to be pronounced only at higher values of f s . Under extensional flows, the computed stress (and viscosity) is higher at higher f s and l regardless of strain rate. Beyond a critical strain rate, we observe fragmentation of the associative clusters, which has interesting effects on the stress/viscous response.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Review of Low-Cost Organic and Inorganic Phase Change Materials with Phase Change Temperature between 0°C and 65°C

Phase change materials (PCMs) that undergo a phase transition may be used to provide a nearly isothermal latent heat storage at the phase change temperature. This work reports the energy storage material cost ($/kWh) of various PCMs with phase change between 0-65°C. Four PCM classes are analyzed for their potential use in building systems: 1) inorganic salt hydrates, 2) organic fatty acids, 3) organic fatty alcohols, and 4) organic paraffin waxes. Many salt hydrates have low material costs (0.09 - 2.53 $-kg-1), high latent heat of fusion (100-290 J-g-1), and high densities (1.3-2.6 g-cm-3), leading to favorable volumetric storage density and low energy storage costs, 50-130 kWh-m3 and 0.90-40 $-kWh-1, respectively. Some salts are notably more expensive due to their scarcity or pressures from competing industries such as lithium-based salts. Fatty acids have the lowest energy storage cost in the temperature range 8-17°C at 6.50 – 40 $-kWh-1. Despite favorable latent heat (125 – 250 J-g-1) their low density gives (0.9 g-cm3) gives poor volumetric storage capacity, 32 – 80 kWh-m3. Fatty alcohols generally have high material costs 2.50 – 200 $-kg-1 which leads to high energy storage costs, 40-3000 $/kWh. With latent heat and density similar to fatty acids, fatty alcohols have poor volumetric energy storage, 43 – 55 kWh-m-3.Paraffin waxes containing only a single length carbon chain have a higher energy cost (15 – 500 $-kWh-1) than generic paraffin waxes containing many lengths of carbon chains (7 – 30 $-kWh-1). Pure waxes have a discrete phase change temperature due to their homogeneity. In contrast, a less refined generic wax with several carbon chain lengths is more likely to have a pronounced temperature glide during its phase change. Pure single carbon chain waxes are generally required for applications <45°C as generic paraffin waxes melt between 45-70°C. For many waxes, a solid-solid transition occurs at temperatures below the solid-liquid phase change. For pure paraffins with carbon content ≥22 C atoms, these transitions may appear near the same temperature resembling a temperature glide.The challenges with fatty acids, fatty alcohols, and waxes are low thermal conductivity, low density, some flammability concerns, and compatibility issues with some common engineering materials such as polymers. Challenges with salt hydrates are pronounced supercooling (>5°C), incongruent melting, and corrosiveness. All PCMs may degrade if exposed to ambient conditions and therefore require proper sealing.

Hirschey, Jason↗
DOE OSTI2025

Chemical Recycling of Polycaprolactones via Reactive Melt Processing

Chemical recycling is a promising technology for the deconstruction of waste plastics into monomers or other chemical intermediates, which can be converted into other value-added products or repolymerized into polymers. In this work, polycaprolactone and poly(4-propylcaprolactone) were chemically recycled by exploiting ring-closing depolymerization (RCD). To demonstrate the utility of this approach, reactive distillation experiments were initially conducted in a heated round-bottom flask with a distillation head to explore the effect of temperature and catalyst loading on RCD. Inspired by industrial devolatilization equipment, analogous experiments were conducted using a twin-screw melt compounder that was modified to simultaneously heat and mix polymer in the presence of a catalyst while continuously removing the evolved monomer vapors with a vacuum system and collecting them in a cold trap. Yield and selectivity of the recovered monomer were characterized by 1 H nuclear magnetic resonance spectroscopy and gas chromatography-mass spectrometry. Importantly, the more scalable twin-screw melt compounder approach produced values of monomer selectivity (∼90%) and yield (∼80%) similar to those of the round-bottom flask experiments. The recovered monomers were also successfully repolymerized into the same neat polymer with comparable molar masses without purification steps or adding initiator. Here, the results of this study promote the use of reactive devolatilization extrusion as a scalable approach to polyester depolymerization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Microscopic Dynamics Controls Coupling and Cluster Formation in Brush Particle Solids

Thermodynamics-based models predict the structure of polymer-grafted nanoparticles (PGNs) as well as their assembly behavior based on geometric parameters such as particle size, degree of polymerization, and density of grafted chains. The role of microscopic polymer dynamics, such as the mobility of repeat units in the melt state, in the evolution of the structure and properties remains unknown. Brillouin light spectroscopy (BLS), due to its capability to concurrently discern the local and global elastic properties of PGN assemblies, enables the probing of microscopic processes, such as brush interdigitation, sensitive to the annealing of the assembly. For poly(methyl methacrylate) (PMMA)-grafted silica (SiO 2 ) PGNs in the dry powder state and annealed above the glass transition temperature, BLS revealed fully reversible local elasticity, indicative of limited interdigitation between adjacent PGNs. This contrasts with polystyrene (PS)−SiO 2 analogs that displayed ready (and irreversible) fusion of brush layers during annealing. The retardation of brush interdigitation in PMMA-grafted systems is surprising, given the similar thermomechanical properties of both polymers, and is rationalized as the consequence of higher friction between PMMA repeats compared to PS. Microscopic dynamics thus has a profound impact on the kinetic path of structure (and property) evolution and thus should be considered during the processing of PGNs into functional hybrid materials.

chemical structure↗
DOE OSTI2024

High performance long chain polyesters via melt copolymerization of cutin-inspired monomers

Biopolymers have exhibited potential as sustainable and circular replacements to existing commodity thermoplastic polymers. However, current biopolymers are limited by poor thermomechanical performance compared with their petroleum-derived counterparts. Herein, we report a simple strategy to achieve good mechanical properties in bio-inspired long-chain polyesters via melt copolymerization. By combining mono- and poly-hydroxyl functionalized long chain fatty acids, we show that tough, semi-crystalline materials can be produced that outperform related biopolymers in terms of their thermomechanical behavior. Finally, we envision that long-chain polyesters derived from hydroxylated fatty acids represent an ideal platform to create the next generation of commodity thermoplastics that possess advantaged properties, inherent biodegradability, and feedstock stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Structure/property relationship of semicrystalline polymers during tensile deformation: a molecular dynamics approach

Molecular dynamics (MD) simulation with an ab initio numerical model is conducted to study the structure–property relationship of semicrystalline polymers during uniaxial deformation. The effects of chain length, temperature, and strain rate on mechanical properties are discussed. The influences of microstructural evolution such as bond length, entanglement density, and chain orientation are also studied quantitatively. The temperature will greatly affect the chain conformation in amorphous domains, and the results revealed that the interaction of amorphous and crystalline domains played a crucial role during stretching. Accordingly, the yielding of semicrystalline polymers follows different mechanisms at temperatures above and below T g . A melt-recrystallization scheme is observed during yielding at higher temperatures, while destruction of crystal structures is observed at lower temperatures at the yield point. The correlated effects of different temperatures and strain rates on mechanical properties are examined. This research is part of our efforts to develop a digital twin of a real experiment for efficient optimization of polymer material properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Threading–Unthreading Transition of Linear-Ring Polymer Blends in Extensional Flow

Adding small amounts of ring polymers to a matrix of their linear counterparts is known to increase the zero-shear-rate viscosity because of linear-ring threading. Uniaxial extensional rheology measurements show that, unlike its pure linear and ring constituents, the blend exhibits an overshoot in the stress growth coefficient. By combining these measurements with ex-situ small-angle neutron scattering and nonequilibrium molecular dynamics simulations, this overshoot is shown here to be driven by a transient threading–unthreading transition of rings embedded within the linear entanglement network. Prior to unthreading, embedded rings deform affinely with the linear entanglement network and produce a measurably stronger elongation of the linear chains in the blend compared to the pure linear melt. Thus, rings uniquely alter the mechanisms of transient elongation in linear polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

The mechanical properties of Kel-F 800 (FK-800) as a function of crystallinity

Kel-F 800 is a copolymer of chlorotrifluoroethylene PTFE (75 wt. %) and vinylidene fluoride PVDF (25 wt. %). It has previously been used as a PBX binder for insensitive explosives such as PBX 9502 and LX-17. 3M started production of Kel-F 800 in 1957 and small-scale batches continued to be made until 2002 when production ceased due to environmental concerns regarding one of the emulsifiers used during production. Around 2000 the Kel-F 800 name was changed to FK-800 to avoid trademark concerns because rights to produce another polymer with a similar tradename (Kel-F 81) had been sold to another manufacturer. The Kel designation came from the original manufacturer of PCTFE (Kel-F 81), the Kellog company. To avoid confusion this document will only refer to Kel-F 800. In 2006, production of small-scale batches of Kel-F 800 was started again by 3M in response to customer enquiries. This new material, the first blended batch is referred to as LOT 1, was produced with a different emulsifier than used previously. Because Kel-F 800 is made in a small batch reactor, considerable variation in crystallinity can be expected from lot to lot and year to year. In many ways, this is not significant since the material is dissolved in a solvent (often MEK, ethylmethyl ketone or ethyl acetate) for PBX production purposes. This destroys the as received crystallinity and the resulting crystallinity in the processed material is a function of polymer molecular weight and thermal history. Producing large billets of Kel-F 800 from solvent extraction is not practical and so a compression molding technique has been used above the melting temperature. This method also removes residual crystallinity from the supplied granules. The molecular weight of a polymer can be estimated by several techniques, the most common being gel permittivity chromatography (GPC), size exclusion chromatography (SEC) and shear rheometry measurements of polymer/solvent solutions. Changes in molecular weight will affect the crystallization rate and the maximum crystallinity reached for a specific thermal history. Both references agree that the new LOT 1 material molecular weight falls within the deviation found from averaging previous historical lots of Kel-F 800.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Polymer Chain Diffusion in All-Polymer Nanocomposites: Confinement vs Chain Acceleration

All-polymer nanocomposites, in which soft, polymer-based nanoparticles are dispersed in the polymer matrix, have received great interest lately due to their potential use in a range of applications, including drug delivery and self-healing materials. However, the impact of this new class of nanoparticles on the dynamics of a linear polymer matrix in an all-polymer nanocomposite is still largely unknown. In this work, we report that the addition of polystyrene soft nanoparticles accelerates the diffusion of high molecular weight linear PS chains over a range of nanoparticle loadings. Our results show that at nanoparticle loadings below 1%, the diffusion of the linear matrix increases, presumably via a constraint release mechanism. At loadings above 1%, the increase in diffusion is mitigated by confinement effects of the nanoparticles. Thus, the response of these all-polymer nanocomposites is dominated by the balance of entropic confinement of the chain, which slows diffusion and a constraint release mechanism that speeds up the diffusion. However, the diffusion of the linear chain in the all-polymer nanocomposite is faster than that of the same chain in the melt at all loadings, diverging from the behavior of most nanocomposites with hard, impenetrable nanoparticles. Thus, the mechanism that accelerates the chain diffusion dominates in these systems. This behavior is unusual and fundamentally different than what has been reported for nanocomposites with hard inorganic nanoparticles, indicating that new perspectives are needed for these materials where the control of loading can either accelerate or decelerate the dynamics of the matrix in a distinctive manner.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Comparison of nanocomposite dispersion and distribution for several melt mixers

Breakup (dispersion) and distribution of nanoparticles are the chief hurdles towards taking advantage of nanoparticles in polymer nanocomposites for reinforcement, flame retardancy, conductivity, chromaticity, and other properties. Microscopy is often used to quantify mixing, but it has a limited field of view, does not average over bulk samples, and fails to address nano-particle hierarchical structures. Ultra-small-angle X-ray scattering (USAXS) can provide a macroscopic statistical average of nanoscale dispersion (breakup) and emergent hierarchical structure, as well as the distribution on the nanoscale. Here, this work compares several common mixer geometries for carbon black-polystyrene nanocomposites. Two twin-screw extruder geometries, typical for industrial processing of melt blends, are compared with a laboratory-scale single screw extruder and a Banbury mixer. It is found that for a given mixer, nanoscale distribution increases following a van der Waals function using accumulated strain as an analogue for temperature while macroscopic distribution/dispersion, using microscopy, does not follow this dependency. Breakup and aggregation in dispersive mixing follow expected behavior on the nanoscale. Across these drastically different mixing geometries an unexpected dependency is observed for nanoscale distributive mixing (both nano and macroscopic) as a function of accumulated strain that may reflect a transition from distributive turbulent to dispersive laminar mixing as the mixing gap is reduced.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Variation of Aliphatic Diisocyanates in Bio-Based TPUs

The utilization of bio-based materials for polymer production poses a challenge to both the industrial and academic sectors due to the availability and production costs of the necessary raw materials. Diisocyanates necessary for polyurethane synthesis have posed a particular challenge, given the paucity of natural diamine precursors for traditional phosgenation. We recently developed a phosgene-free flow chemistry methodology that allows for the safe, efficient, and scalable preparation of diisocyanates from naturally produced diacids. This chemistry broadens the potential for the development of renewable diisocyanates for a broad variety of applications. Here, we expand upon this work by demonstrating the scaled production of a panel of bio-based linear, aliphatic diisocyanates, with chain lengths ranging from four to eight carbons in good yields of 57–81% and high purity (~97%). Furthermore, these are applied to the synthesis of thermoplastic polyurethanes (TPUs) containing up to a 100% renewable carbon content. TPUs formulated using shorter carbon-chained diisocyanates displayed a higher tensile strength compared to those formulated using longer chains. Ready access to diisocyanates of varying chain length affords the ability to tailor TPU properties through careful selection of the diisocyanate, polyol, and chain extender, offering hard and soft TPUs for multiple end-use applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Leveraging Stereochemistry to Optimize the Properties of Polyhydroxyalkanoates

The recycling of low-density polyethylene (LDPE) is challenging due to difficulties with sorting and contamination, leading to environmental harm. Polyhydroxyalkanoates (PHAs) are at the forefront of high-performance biodegradable alternatives to olefinic plastics, but few offer LDPE-like properties such as low strength and crystallinity while maintaining high ductility and thermal stability. Herein, we report a series of isoenriched transpoly( 3-hydroxy-2-methylbutyrates) (trans-PHMBs) with tunable mechanical and thermal properties. These polymers were synthesized through ring-opening polymerization of racemic trans-3,4-dimethylpropiolactone (rac-trans-DMPL), sourced from C1 and C4 feedstocks, using a new class of “sandwich” C 2 symmetric rac-( Ar BDI*)ZnO i Pr catalysts (where BDI = β-diketiminate). Variation of aromatic groups (Ar) and polymerization temperature yielded mm%s between 45−79% and melting temperatures (T m ) between 141−174 °C. trans-PHMB with intermediate isotacticities of 73 and 75 mm% exhibit similar stress−strain profiles to LDPE, indicating that these polymers have the potential to serve as higher melting, degradable substitutes for LDPE.

Biopolymers↗
DOE OSTI2025

Impact of Hydroxyl Functionalization and Unsaturation on Linear Poly(ethylene- co -vinyl alcohol)

Functionalization of C═C in unsaturated polyolefins by hydroboration/oxidation successfully generates linear poly(ethylene-co-vinyl alcohol) (LEVOH) polymers. This postpolymerization modification expands upon previously reported chemistry to control the extent of functionalization through reagent stoichiometry. Partial functionalization (24–92% of C═C) of polycyclooctene produces materials with both C═C in the backbone and pendant OH and subsequent hydrogenation generate a LEVOH. We explore the thermal, structural, surface, and adhesive properties of these LEVOH and the partially unsaturated intermediate and find they are impacted by both the extent of OH incorporation and saturation. The presence of C═C significantly reduces the melting temperature and crystallinity while increasing surface polarity and adhesive strength compared with saturated polymers at equivalent functionalization. Furthermore, this investigation demonstrates linear analogs of EVOH with a wide range of properties tuned by extent of hydroxylation and presence of unsaturation.

Crystal structure↗
DOE OSTI2023

Melt Blending: A Tool to Simplify Plastic Scintillator Synthesis

Plastic scintillators are widely used as radiation detection media in homeland security and nuclear physics applications. Their attributes include low cost, scalability to large detector volumes, and additive compounding to enable additional material and detection features, such as pulse shape discrimination (PSD), gamma-ray spectroscopy, aging resistance, and coincidence timing. However, traditional chemically cured plastic scintillators (CCS) require long reaction times, and hazardous wet chemical procedures performed by specially trained personnel, and can leave residual monomer, resulting in deleterious optical and material properties. Here, we synthesize melt blended scintillators (MBSs) in 2.5 days using easily accessible solid-state compounding of commercially-available poly(styrene) with 30–60 wt% fluorene-based compound “P2” to create monolithic detectors with < 100 ppm residual monomer, in several form factors. Further, the best scintillation performance was recorded for 60 wt% P2 in Styron 665, including gamma-ray light yield 139% of EJ- 200 commercial scintillator and PSD figure of merit (FOM) value of 2.65 at 478 keVee, approaching P2 organic glass scintillator (OGS). The capability of MBS to generate fog-resistant scintillators and poly(methyl methacrylate) (PMMA)-based scintillators for use in challenging environments is also demonstrated.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2024

Biocomposite thermoplastic polyurethanes containing evolved bacterial spores as living fillers to facilitate polymer disintegration

The field of hybrid engineered living materials seeks to pair living organisms with synthetic materials to generate biocomposite materials with augmented function since living systems can provide highly-programmable and complex behavior. Engineered living materials have typically been fabricated using techniques in benign aqueous environments, limiting their application. In this work, biocomposite fabrication is demonstrated in which spores from polymer-degrading bacteria are incorporated into a thermoplastic polyurethane using high-temperature melt extrusion. Bacteria are engineered using adaptive laboratory evolution to improve their heat tolerance to ensure nearly complete cell survivability during manufacturing at 135 °C. Furthermore, the overall tensile properties of spore-filled thermoplastic polyurethanes are substantially improved, resulting in a significant improvement in toughness. The biocomposites facilitate disintegration in compost in the absence of a microbe-rich environment. Finally, embedded spores demonstrate a rationally programmed function, expressing green fluorescent protein. This research provides a scalable method to fabricate advanced biocomposite materials in industrially-compatible processes.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Manufacturing of Continuous Core–Shell Hydrated Salt Fibers for Room Temperature Thermal Energy Storage

The encapsulation of salt hydrate phase change materials (PCMs) in uniform microscale bodies has yet been reported in research due in part to the delicate relationship between thermal performance and water-to-salt ratios which are easily altered during manufacturing. Herein, core–shell composite fibers comprised of a salt hydrate PCM core and a poly(acrylonitrile) (PAN) shell are wet spun in a continuous process using a syringe pump and coaxial die. The PCM phase comprises calcium chloride hexahydrate (CaCl 2 ·6H 2 O) with strontium chloride hexahydrate(SrCl 2 ·6H 2 O) (3 wt%) and fumed silica(SiO 2 ) (2 wt%) as additive, a composition that is prepared from homogenous melt at 40 °C. 15 wt% PAN in dimethylsulfoxide solvent is used to prepare the shell-forming polymer gel. PCM and polymer gel injection rates of 10–40 mL h –1 are used to spin coaxial fibers through a coagulation bath, yielding continuous microtubules with diameters in the range of 850–1500 μm. Cyclic testing shows that after 1000 cycles, melting enthalpies incurred only a 3.5% decline from 131.46 to 126.9 J g –1 . In conclusion, success here overcomes several coincidental drawbacks of PCM fiber performance and manufacturing and delivers the first example of scalable roll-to-roll PCM fiber produced by wet spinning for building material applications.

36 MATERIALS SCIENCE↗