Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plastic deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Thermomechanical Properties of Neutron Irradiated Al 3 Hf-Al Thermal Neutron Absorber Materials

A thermal neutron absorber material composed of Al 3 Hf particles in an aluminum matrix is under development for the Advanced Test Reactor. This metal matrix composite was fabricated via hot pressing of high-purity aluminum and micrometer-size Al 3 Hf powders at volume fractions of 20.0, 28.4, and 36.5%. Room temperature tensile and hardness testing of unirradiated specimens revealed a linear relationship between volume fraction and strength, while the tensile data showed a strong decrease in elongation between the 20 and 36.5% volume fraction materials. Tensile tests conducted at 200 °C on unirradiated material revealed similar trends. Evaluations were then conducted on specimens irradiated at 66 to 75 °C to four dose levels ranging from approximately 1 to 4 dpa. Tensile properties exhibited the typical increase in strength and decrease in ductility with dose that are common for metallic materials irradiated at ≤0.4T m . Hardness also increased with neutron dose. The difference in strength between the three different volume fraction materials was roughly constant as the dose increased. Nanoindentation measurements of Al 3 Hf particles in the 28.4 vol% material showed the expected trend of increased hardness with irradiation dose. Transmission electron microscopy revealed oxygen at the interface between the Al 3 Hf particles and aluminum matrix in the irradiated material. Scanning electron microscopy of the exterior surface of tensile tested specimens revealed that deformation of the material occurs via plastic deformation of the Al matrix, cracking of the Al 3 Hf particles, and to a lesser extent, tearing of the matrix away from the particles. The fracture surface of an irradiated 28.4 vol% specimen showed failure by brittle fracture in the particles and ductile tearing of the aluminum matrix with no loss of cohesion between the particles and matrix. The coefficient of thermal expansion decreased upon irradiation, with a maximum change of –6.3% for the annealed irradiated 36.5 vol% specimen.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The effects of free surfaces on deformation twinning in HCP metals

Deformation twinning is a predominant mode of plastic deformation for hexagonal close packed metals, like Mg and Ti. The heterogenous microstructure and the local stresses associated with twinning play a key role in their mechanical response and fracture. Surface analyses, like electron microscopy, are frequently employed to spatially map microstructure and micromechanical fields in order to study twinning behavior. However, these measurements are inherently influenced by the vicinity of the free surface. In this work, an elasto-visco-plastic fast-Fourier-transform (EVP-FFT) polycrystal modeling approach is employed to investigate the effects of free surfaces on twin development before and after loading. We compare calculated micromechanical fields on free surfaces with those calculated inside the bulk and, in some cases, experimental surface measurements. The results indicate that the creation of free surfaces can promote twin propagation and growth and can influence twin morphology by causing a twin lamella to become larger, more blunted and irregular. The structure along the twin boundaries are also affected, due to the higher driving stresses that extend prismatic-basal and basal-prismatic facets. Furthermore, free surfaces invoke different slip activities in the twin and the surrounding parent crystal by enhancing basal, prismatic and pyramidal slip in some localized regions, while reducing slip in others. We demonstrate that the simulated free-surface effects lead to better qualitative and quantitative agreement with experimental measurements from scanning electron microscopy and digital image correlation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High temperature creep model development using in-situ 3-D DIC techniques during a simulated LOCA transient

In-situ strain measurements of fuel cladding can enable high-throughput data collection and validation to support accelerated qualification of cladding materials. Here, in this work, 3D digital image correlation was used to map strain for both Zircaloy-4 (Zry-4) and Cr-coated Zry-4 during two types of cladding rupture experiments: isobaric temperature ramp tests at 5 °C/s and isothermal pressure jump tests at 600 °C. Zry-4 strain data initially showed a temperature dependence expected for creep deformation, yet a shift to a new plastic deformation mechanism not reported in literature dominated during the finals seconds prior to rupture. Cr-coated Zry-4 did not show the change in deformation mechanism at the end of life and showed a delay in measurable creep deformation. Stress dependences were similar for Zry-4 and Cr/Zry-4 during pressure jump tests. Cr-coatings were found to decrease the strain rate during both testing scenarios. Creep parameters were calculated to support modelling efforts regarding design basis accidents.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Experimental verification of a crystal plasticity-based simulation framework for predicting microstructure and geometric shape changes: Application to bending and Taylor impact testing of Zr

This paper is concerned with experimental verification of a recently developed multi-scale simulation framework for plastic deformation of metallic materials from quasi-static to impact deformation conditions. The framework is a visco-plastic self-consistent (VPSC) polycrystalline model embedded in an implicit finite element method (FE-VPSC) to provide a microstructure-sensitive constitutive response at each material point. Each material point of the FEM model is a polycrystalline aggregate with crystallographic deformation mechanisms operating at the single crystal scale with their evolving activity based on a dislocation density-based hardening law and texture. Four beams and three cylinders machined in different orientations from a textured plate of high-purity zirconium are tested quasi-statically in 4-point bending and at speeds of 100 m/s, 170 m/s and 243 m/s during Taylor impact tests, respectively. The variation in dimensional changes resulting from different sample orientations in the plate with respect to loading directions is measured for each sample. Moreover, texture and twinning characterization is performed using electron backscattered diffraction (EBSD). The deformation processes and underlying evolution of microstructure are successfully simulated using the FE-VPSC framework. In doing so, the model parameters are optimized and validated across a broad range of strain rates and temperatures. Simulation results in terms of geometrical changes and microstructural evolution are compared with the experimental measurements. The model predicts anisotropic material flow resulting from the hard-to-deform crystallographic directions, the development of gradients in texture and twinning through the geometries, tension–compression asymmetry, as well as the extent of plasticity under impact.

42 ENGINEERING↗
DOE OSTI2024

Calibration and validation of the foundation for a multiphase strength model for tin

In this work, the Common Model of Multi-phase Strength and Equation of State (CMMP) model was applied to tin. Specifically, calibrations of the strength-specific elements of the CMMP foundation were developed with a combination of experiments and theory, and then the model was validated experimentally. The first element of the foundation is a 10 multi-phase analytic treatment of the melt temperature and the shear modulus for the solid phases. These models were parameterized for each phase based on ab initio calculations using the software VASP (Vienna Ab initio Simulations Package) based on density functional theory (DFT). The shear modulus model for the ambient β phase was validated with ultrasonic sound speed measurements as a function of pressure and temperature. The second element of the foundation is a viscoplastic strength model for the β phase, upon which strength for inaccessible higher-pressure phases can be scaled as necessary. The stress-strain response of tin was measured at strain rates of 10 -3 to 3 x 10 3 s -1 and temperatures ranging from 87 to 373 K. The Preston-Tonks-Wallace (PTW) strength model was fit to that data using Bayesian model calibration. For validation, six forward and two reverse Taylor impact experiments were performed at different velocities to measure large plastic deformation of tin at strain rates up to 10 5 s -1 . The PTW model accurately predicted the deformed shapes of the cylinders, with modest discrepancies attributed to the inability 20 of PTW to capture the effects of twinning and dynamic recrystallization. Some material in the simulations of higher velocity Taylor cylinders reached the melting temperature, thus testing the multiphase model because of the presence of a second phase, the liquid. In simulations using a traditional modeling approach, the abrupt reduction of strength upon melt resulted in poor predictions of the deformed shape and non-physical temperatures. With CMMP, the most deformed material points evolved gradually to a mixed solid-liquid but never fully liquid state, never fully lost strength, 25 stayed at the melt temperature as the latent heat of fusion was absorbed, and predicted the deformed shape well.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deformation behavior of a Co-Cr-Fe-Ni-Mo medium-entropy alloy at extremely low temperatures

In this work, we report the mechanical and microstructural characteristics of a medium-entropy alloy, Co 17.5 Cr 12.5 Fe 55 Ni 10 Mo 5 (atomic percent, at%) at cryogenic temperatures, down to a record low temperature of 0.5 K. The alloy exhibits excellent strength and ductility combined with a high strain-hardening rate in the entire temperature range investigated. Its property profile, including the yield strength, ultimate tensile strength, strain hardening capability, and absorbed mechanical energy, is better than those of most alloys and HEAs used in cryogenics. Within the interval of extremely low temperatures considered (0.5–4.2 K), the alloy exhibits several unusual features, including anomalies of the temperature dependence of the yield strength and tensile ductility, discontinuous plastic deformation (DPF), and a change in the propensity for the deformation-induced martensitic transformation. While the occurrence of these effects in the same temperature interval may be fortuitous, we hypothesize that they are interrelated and provide a tentative explanation of the observed phenomena on this basis.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterization of precipitation in gradient Inconel 718 superalloy

Inconel 718 (IN718) superalloy is a well-established material for the application of aircraft engine and power generator due to its excellent performance at high temperatures. The outstanding mechanical properties of IN718 are largely determined by the precipitates. Here, we investigated the precipitation behaviors and the corresponding mechanical properties of the heat-treated gradient IN718 alloy. The microscopy studies reveal that high-density hexagonal η phase with chemistry of Ni 3 (Al,Ti,Nb) formed in the nanograined IN718 alloy after annealing at 700 °C. Additionally, the compressive stress introduced during severe plastic deformation may have prohibited the formation of γ” phase while accelerated the precipitation of γ’ phase, consequently favoring the precipitation of η phase. The corresponding evolution of mechanical behavior of gradient IN718 alloy is investigated.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Characteristics of oxide-dispersion strengthened alloys produced by high-temperature severe deformation

This study is to explore an economically attractive and technically feasible processing method for oxide-nanoparticle strengthened alloys for fusion reactor application. Despite many scientific merits of the advanced oxide-dispersion strengthened (ODS) alloys, such as the nanostructured ferritic alloy (NFA) 14YWT, the only viable production path for a high-quality NFA is the high-power mechanical alloying process. This process is often a multi-day high-speed ball milling of alloy powder with a small quantity of yttria (Y 2 O 3 ) powder, followed by the milled-powder consolidation using extrusion or other methods and additional thermomechanical processing (TMP) for property control. This complex production path, including the low-temperature mechanical alloying in particular, has limited technical advancement toward the cost-effective and scale-up production of ODS alloy components. To overcome such a practical limitation, we proposed to explore alternative low-cost processing routes using traditional thermomechanical processing (TMP) method only. Further, a series of continuous TMP cycles, which were designed to impose high-temperature severe plastic deformation (HT-SPD) conditions to the consolidated powder mixtures, were applied to achieve the effective distribution of oxide particles in nanograin structure and thus desirable mechanical properties. Since the reduced-activation ferritic-martensitic (RAFM) alloy powders (Fe-10Cr and Fe-14Cr alloys with various Y contents) are available in our inventory, we focused to utilize the new solid-state synthesis approach for controlling oxide (oxygen source) dissolution and nanoscale clustering in nanograin structure in those alloys. A combination of powder consolidation at 900 °C and continuous thermomechanical activation at 600 °C yielded two essential ODS alloy microstructure contents–nanograin structure and nanoparticle distribution–and thus demonstrated a good combination of strength and ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Evaluation of the ring tension test (RTT) for robust determination of material strengths

The ring tension test (RTT) is an experimental method for determining mechanical behavior in a material’s circumferential or hoop direction. It is a crucial test for testing anisotropic materials with tube geometry, such as nuclear fuel cladding or irradiated pipes. Several RTT configurations exist, each with their own advantages and disadvantages. However, this test is significantly more complex than traditional tensile testing and can be especially sensitive to small differences and inconsistencies in the test setup and geometry, ultimately affecting the derived mechanical properties. Previous research has focused on method development, and little work has been done on understanding the subtle differences between an ideal test and experiments, specifically when the tests are performed on highly irradiated materials in hot cells. In this work, a finite element-based investigation of the RTT is conducted to fill this gap. The two most used test configurations are investigated, comparing their ability to determine accurate material strengths through plastic deformation. Several non-ideal conditions and uncontrollable effects which are likely to occur during experimental testing such as machining tolerances, variations of specimen geometry from nominal dimensions, rotation of specimens and fixturing, and other test setup discrepancies are studied. The sensitivity of measured strengths to these conditions is presented. A mechanics-based approach to describing and correcting raw data to determine actual strengths is also included for one of the configurations, resulting in a robust correction method with highly accurate material strength measurements. Finally, based on these analyses, the hemicylindrical mandrel configuration is recommended with a gauge region oriented at a 45° angle.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Multi-material additive manufacturing of aluminum 6061-T6 alloy with stainless steel 304: Suppression of intermetallic compounds and interface growth mechanism

Fabricating integrated aluminum-steel structures is difficult because of metallurgical incompatibilities that promote intermetallic compound (IMC) formation at their interfaces. This work introduces a practical route for additively manufacturing 6061-T6 aluminum alloy (AA6061-T6) directly onto 304 stainless steel (SS304) using a high shear strain rate-assisted interfacial bonding mechanism. Through the friction extrusion deposition-based additive manufacturing method, both single- and multi-layer deposits of AA6061-T6 were successfully fabricated on SS304, yielding a robust hybrid multi-material structure. Comprehensive analyses of deposition quality, interface porosity, and bonding performance showed that the interface achieved a tensile strength exceeding 154 MPa under quasi-static loading. Microstructural observations revealed that the deposited aluminum layers experienced severe plastic deformation, resulting in pronounced grain refinement. Importantly, the interfacial zone was found to be free of brittle IMCs, instead containing a thin amorphous layer that evolved through a non-linear reaction-zone growth law. This solid-state additive strategy establishes a promising pathway for lightweight structural systems, nuclear energy component cladding, and multifunctional engineering components, redefining how dissimilar metals can be integrated for advanced applications.

Aluminum alloy↗
DOE OSTI2021

Discovering SPP Thermomechanical Pathways

Final report for SPPSi project in Thrust One Friction extrusion is a thermomechanical process that combines conventional extrusion with the action of a rotating die. The plastic deformation of the material being sheared and extruded is the primary source of process heat and it produces strain distributions unlike those resulting from conventional extrusion. This paper proposes an improved strain analysis that evaluates three main strain components in a series of rate-controlled friction extrusions in which the steady state was achieved. Cylindrical AA1100 extrusion billets with two embedded markers were extruded to wire with a 10:1 diametral reduction. The shape change of the embedded markers was determined via serial, transverse sectioning and quantitative metallography of the extruded wires. Three mutually orthogonal strain components (longitudinal, circumferential, and radial) were calculated at different positions along each extruded wire from the marker's shape change. The development of strain from the initial transient to the steady state is discussed. The variation of the steady-state strain with different process parameters is correlated with the die advance per revolution.

42 ENGINEERING↗
DOE OSTI2023

White Laue and powder diffraction studies to reveal mechanisms of HCP-to-BCC phase transformation in single crystals of Mg under high pressure

Mechanisms of hexagonal close-packed (HCP) to body-centered cubic (BCC) phase transformation in Mg single crystals are observed using a combination of polychromatic beam Laue diffraction and monochromatic beam powder diffraction techniques under quasi-hydrostatic pressures of up to 58 ± 2 GPa at ambient temperature. Although experiments were performed with both He and Ne pressure media, crystals inevitably undergo plastic deformation upon loading to 40–44 GPa. The plasticity is accommodated by dislocation glide causing local misorientations of up to 1°–2°. The selected crystals are tracked by mapping Laue diffraction spots up to the onset of the HCP to BCC transformation, which is determined to be at a pressure of 56.6 ± 2 GPa. Intensity of the Laue reflections from HCP crystals rapidly decrease but no reflections from crystalline BCC phase are observed with a further increase of pressure. Nevertheless, the powder diffraction shows the formation of 110 BCC peak at 56.6 GPa. The peak intensity increases at 59.7 GPa. Upon the full transformation, a powder-like BCC aggregate is formed revealing the destructive nature of the HCP to BCC transformation in single crystals of Mg.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Gradient nanostructuring via compositional means

Nanocrystalline metals are inherently unstable against thermal and mechanical stimuli, commonly resulting in significant grain growth. Also, while these metals exhibit substantial Hall-Petch strengthening, they tend to suffer from low ductility and fracture toughness. With regard to the grain growth problem, alloying elements have been employed to stabilize the microstructure through kinetic and/or thermodynamic mechanisms. And to address the ductility challenge, spatially-graded grain size distributions have been developed to facilitate heterogeneous deformation modes: high-strength at the surface and plastic deformation in the bulk. In the present work, we combine these two strategies and present a new methodology for the fabrication of gradient nanostructured metals via compositional means. Here, we have demonstrated that annealing a compositionally stepwise Pt-Au film with a homogenous microstructure results in a film with a spatial microstructural gradient, exhibiting grains which can be twice as wide in the bulk compared to the outer surfaces. Additionally, phase-field modeling was employed for the comparison with experimental results and for further investigation of the competing mechanisms of Au diffusion and thermally induced grain growth. This fabrication method offers an alternative approach for developing the next generation of microstructurally stable gradient nanostructured films.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tensile deformation behavior of twist grain boundaries in CoCrFeMnNi high entropy alloy bicrystals

High entropy alloys (HEA) are a class of materials that consist of multiple elemental species in similar concentrations. The use of elements in far from dilute concentrations introduces a multi-dimensional composition design space by which the properties of metallic systems can be tailored. While the mechanical behavior of HEAs has been the subject of active research recently, the role of grain boundaries (GBs) in their deformation behavior remains poorly understood. Motivated by recent experiments on HEAs demonstrating that GBs act as nucleation sites for deformation twins, herein, we leverage atomistic simulations to construct a series of equiatomic CoCrFeMnNi HEA bicrystals with $\langle 110 \rangle$ and $\langle 111 \rangle$ symmetric twist GBs and examine their tensile behavior and underlying deformation mechanisms at 77 K. Simulation results reveal that plastic deformation proceeds by the nucleation of partial dislocations from GBs, which then grow with further loading by bowing into the bulk crystals leaving behind stacking faults. Variations in the nucleation stress exist as function of GB character, defined in this work by the twist angle. Our results provide future avenues to explore GBs as a microstructure design tool to develop HEAs with tailored properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Elastic-plastic conductor damage evaluation at over 0.4% strain using a high-stress REBCO coil

Abstract Recent reports on screening current stress simulations of high-field REBCO magnets frequently present peak stresses over 1 GPa. However, this result is probably an unrealistic artifact of purely elastic calculations, considering the macroscopic yield and fracture stresses of approximately 900 MPa and less than 1.1 GPa for Hastelloy substrate-coated conductors. Here, we evaluate elastic-plastic conductor damage at over 0.4% strain using a high-stress REBCO coil exposed to a high field to explore this elastic-plastic regime. The coil was located off-center in a low-temperature superconductor magnet so as to induce a significant screening current in the enhanced radial field. Voltage taps, a Hall sensor, and two strain gauges were used for the instrumentation. We obtained strains exceeding 0.4% near the outward edge during the coil current charge from 350 A to 390 A, where the coil was exposed to external axial and radial magnetic fields of 13 T and 0.5 T. Post mortem results showed wavy plastic deformation, electrical damage, and REBCO defects. An elastic-plastic simulation reproduced the measured strains and predicted that ∼1 GPa stress is sufficient to induce ∼0.9% strain, thus validating our initial concerns with purely elastic models. This paper provides our experimental and simulation results.

Bang, Jeseok (ORCID:0000000247616334)↗
DOE OSTI2026

Unlocking superplasticity in medium and high-entropy alloys

Superplasticity, the capacity of materials to sustain extraordinary tensile elongations at elevated temperatures, underpins a range of advanced metal-forming technologies. Conventionally, it is achieved in fine-grained alloys where deformation is dominated by grain-boundary sliding, accommodated by diffusion and dislocation activity. The advent of medium- and high-entropy alloys (M/HEAs), with their high chemical complexity and unconventional phase stability, offers new pathways to superplastic behavior beyond traditional alloy systems. Although investigated only recently, several M/HEAs already exhibit elongations that rival or exceed those of classical superplastic materials, particularly when ultrafine or metastable microstructures are engineered. Here, we review progress in understanding superplastic deformation in M/HEAs, emphasizing the interplay among composition, initial microstructure, thermomechanical processing, and microstructural evolution during high-temperature deformation. We discuss approaches to generating the fine-grained structures necessary for grain-boundary sliding, including severe plastic deformation and tailored heat treatments. We further highlight dynamic phenomena such as phase transformations, evolving grain-boundary chemistry, and deformation-induced grain refinement that can enhance plasticity in these systems. These mechanisms often shift the balance of deformation processes, enabling large elongations even outside classical criteria. Finally, we outline key challenges for application, including cost, scalability, recyclability, and microstructural stability.

klenam, Desmond [University of the Witwatersrand, ↗
DOE OSTI2022

Effect of loading path on grain misorientation and geometrically necessary dislocation density in polycrystalline aluminum under reciprocating shear

Solid phase processing (SPP) is a promising alloy fabrication technique to produce fine and homogeneous grain structures for high-performance alloys. However, there is very limited modeling capability to understand and predict the grain refinement during SPP. In this work, the crystal plasticity theory was used to study elastic-plastic deformation in polycrystalline aluminums under large shear deformation. Two approaches, kernel averaged misorientation (KAM) and grain reference orientation deviation (GROD), were used to assess the grain misorientations. The geometrically necessary dislocation (GND) density was computed with the plastic strain rate. The deformation simulations were carried out under two loading conditions to investigate the effect of loading paths on the evolutions of grain misorientation and GND density. The results show that the regions with high misorientation and GND density first appear near grain boundaries. These regions then extend toward interior grains. The loading path affects dislocation system activation and dislocation recovery, hence dislocation evolution and misorientation. In conclusion, both two- and three-dimensional simulations showed that the spatial and temporal evolutions of GROD, KAM, and GND density in are closely correlated, which indicates they all can be used as criteria of grain refinement or recrystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Atomistic simulations of nanoindentation on nanoglasses: Effects of grain size and gradient microstructure on the mechanical properties

The use of nanoglass (NG) microstructures has been shown as an effective strategy to improve the ductility of rather brittle metallic glass alloys. To evaluate the effects of grain size and gradient design on the mechanical properties of NGs, we perform molecular dynamics simulations of nanoindentation on Cu 64 Zr 36 NGs. We consider samples with uniform 3 and 7 nm grain sizes as well as gradient microstructures with gradient grain sizes varying from 3 to 7 nm. Here, the results show that the deformation mechanism in NGs with small grain sizes is dominated by the activation and evolution of multiple shear transformation zones. Increasing grain sizes enhances the elastic modulus and hardness at the cost of reduced abrasion resistance. Though the average grain size at the indentation surface plays a crucial role in the deformation behavior of gradient NG models, their strain localization and plastic deformation states are affected by the grain sizes far from the indenter. Desired combinations of mechanical properties can be realized by different NG microstructure designs.

36 MATERIALS SCIENCE↗