Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optimistic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

The BATSE SLED: The problem and the correction

The Burst And Transient Source Experiment (BATSE) has been in space for 4 months and, by anyone's reckoning, is performing better than even the most optimistic pre-flight predictions. That doesn't mean there haven't been some small surprises. Because of the discreteness of gamma-ray energies available to us in pre-flight testing, we could not subject the instrument to the continuous distribution of energies it now sees in space. Therefore, it was not until the beginning of mission operations that a small non-linearity was discovered in the low energy region of the SPD spectra. The nickname for this depression is the SLED (Spectroscopy Low-Energy Depression). Sample spectra for module 6 at two gains (1X and 0.4X) are given. Note that the position of the sled is gain-independent in channel space. A further study on a non-flight module discovered the cause lay in the spectroscopy analog electronics. Above a certain energy threshold, the digital signal from the SPEC-FAST2 discriminator causes, in effect, an extra small amount of charge to be added to the SHER analog input. The laboratory measurements of SHER output energy as a function of input energy are presented. The change of slope at the point of the SLED results in narrower bin widths for the channels in that region. The SLED is approximately 5 channels wide. It should be mentioned that below the SLED and for many decades above the SLED the response is extremely linear. The proposed fix was to move the lower straight line up to match the extrapolation of the upper straight line, shown by the dotted line. In effect, this means reassigning channel numbers. All channel edges lower than the SLED are moved a fixed amount to higher channel numbers. Channel edges in the SLED are moved a different amount depending on their position. The latter obviously results in narrower channel widths in energy space.

Lestrade, John Patrick↗

Progress of research of high-Tc superconductors

Research in the area of of high T(sub c) superconductors has made great progress in the last few years. New materials were found and the systematic investigation of these materials has contributed to understanding the mechanism of high T(sub c) superconductivity. The critical currents in thin films, bulks, and tapes increased drastically, and the origin of flux pinning will be clarified in the near future. The future of high T(sub c) superconductivity, in both the basic and applied research areas, is very optimistic. Recent activities in research of high T(sub c) superconductivity and superconductors in Japan are overviewed.

Tanaka, Shoji↗

Lubricant Selection Manual, Phase 3

Future spacecraft must be designated to operate for very long time periods in space. For example, a target goal for the Space Station is 30 years of operation. Although the actual life may be significantly less than this optimistic goal, the life will certainly be a critical issue in design. The bearings on primary components such as the alpha and beta joints must obviously be designed and lubricated with the objective of optimum performance life. In addition to these joints, there will be numerous other tribological (rubbing or rolling) interfaced that will be required to function for the life of the spacecraft. A major key to adequate performance of tribological interface is proper lubrication. Lubricants can be divided into two basic classes: solid films and liquids. Both types have been used extensively in space applications. Both have advantages and disadvantages that must be carefully considered in their selection. The purpose here is to summarize selection criteria for liquid and solid lubricants applied to long-life spacecraft.

Kannel, J. W.↗

Survey and analysis of research on supersonic drag-due-to-lift minimization with recommendations for wing design

A survey of research on drag-due-to-lift minimization at supersonic speeds, including a study of the effectiveness of current design and analysis methods was conducted. The results show that a linearized theory analysis with estimated attainable thrust and vortex force effects can predict with reasonable accuracy the lifting efficiency of flat wings. Significantly better wing performance can be achieved through the use of twist and camber. Although linearized theory methods tend to overestimate the amount of twist and camber required for a given application and provide an overly optimistic performance prediction, these deficiencies can be overcome by implementation of recently developed empirical corrections. Numerous examples of the correlation of experiment and theory are presented to demonstrate the applicability and limitations of linearized theory methods with and without empirical corrections. The use of an Euler code for the estimation of aerodynamic characteristics of a twisted and cambered wing and its application to design by iteration are discussed.

Carlson, Harry W.↗

Availability of positioning and receiver autonomous integrity monitoring for the global positioning system

Receiver-autonomous integrity monitoring (RAIM) of GPS data is examined by means of a simulation of the availability of a RAIM system that can provide both a GPS coverage model and a Markov reliability model. State probabilities of GPS failure scenarios are assigned with the Markov model with a maximum of 6 simultaneous satellite failures. The parametric analysis of the failures on GPS RAIM availability includes the maximum allowable value of the horizontal dilution of precision (HDOP), the mean time to repair, and the efficacy of incorporating altimeter measurements. When the HDOP requirement is relaxed the number of RAIM outages is minimized, and poor satellite geometry can lead to a large HDOP. The use of an altimeter can also reduce outages, and RAIM availability increases with optimistic values for the mean time to repair.

Kline, Paul A.↗

Memory management and compiler support for rapid recovery from failures in computer systems

This paper describes recent developments in the use of memory management and compiler technology to support rapid recovery from failures in computer systems. The techniques described include cache coherence protocols for user transparent checkpointing in multiprocessor systems, compiler-based checkpoint placement, compiler-based code modification for multiple instruction retry, and forward recovery in distributed systems utilizing optimistic execution.

Fuchs, W. K.↗

Performance optimization for hard X-ray/soft gamma-ray detectors

This paper discusses the optimization of the performance of imaging scintillation detectors used in the hard X-ray/soft gamma-ray (20-300) keV region of the spectrum. In these devices, absorption of an incident gamma-ray within an alkali halide crystal induces a scintillation light distribution which is centroided by an imaging photomultiplier tube mounted to the crystal. The ultimate imaging resolution is strongly affected by the detailed propagation of the scintillation light within the crystal and at the interface between the crystal and the phototube face plate. A number of refined techniques for preparing the scintillation crystals so as to optimize the imaging resolution have been investigated. The results indicate very good agreement with relatively simple models of the light propagation. It is shown that it is possible to achieve resolution consistent with the most optimistic models.

Harrison, Fiona A.↗

Minimax confidence intervals in geomagnetism

The present paper uses theory of Donoho (1989) to find lower bounds on the lengths of optimally short fixed-length confidence intervals (minimax confidence intervals) for Gauss coefficients of the field of degree 1-12 using the heat flow constraint. The bounds on optimal minimax intervals are about 40 percent shorter than Backus' intervals: no procedure for producing fixed-length confidence intervals, linear or nonlinear, can give intervals shorter than about 60 percent the length of Backus' in this problem. While both methods rigorously account for the fact that core field models are infinite-dimensional, the application of the techniques to the geomagnetic problem involves approximations and counterfactual assumptions about the data errors, and so these results are likely to be extremely optimistic estimates of the actual uncertainty in Gauss coefficients.

Stark, Philip B.↗

The use of activity-based cost estimation as a management tool for cultural change

It will be shown that the greatest barrier to American exploration of the planet Mars is not the development of the technology needed to deliver humans and return them safely to earth. Neither is it the cost of such an undertaking, as has been previously suggested, although certainly, such a venture may not be inexpensive by some measures. The predicted costs of exploration have discouraged serious political dialog on the subject. And, in fact, even optimistic projections of the NASA budget do not contain the resources required, under the existing development and management paradigm, for human space exploration programs. It will be demonstrated that the perception of the costs of such a venture, and the cultural responses to the perceptions are factors inhibiting American exploration of the moon and the planet Mars. Cost models employed in the aerospace industry today correctly mirror the history of past space programs, and as such, are representative of the existing management and development paradigms. However, if, under this current paradigm no major exploration programs are feasible, then cost analysis methods based in the past may not have great utility in exploring the needed cultural changes. This paper explores the use of a new type of model, the activity based cost model, which will treat management style as an input variable, in a sense providing a tool whereby a complete, affordable program might be designed, including both the technological and management aspects.

Mandell, Humboldt↗

TRASYS form factor matrix normalization

A method has been developed for adjusting a TRASYS enclosure form factor matrix to unity. This approach is not limited to closed geometries, and in fact, it is primarily intended for use with open geometries. The purpose of this approach is to prevent optimistic form factors to space. In this method, nodal form factor sums are calculated within 0.05 of unity using TRASYS, although deviations as large as 0.10 may be acceptable, and then, a process is employed to distribute the difference amongst the nodes. A specific example has been analyzed with this method, and a comparison was performed with a standard approach for calculating radiation conductors. In this comparison, hot and cold case temperatures were determined. Exterior nodes exhibited temperature differences as large as 7 C and 3 C for the hot and cold cases, respectively when compared with the standard approach, while interior nodes demonstrated temperature differences from 0 C to 5 C. These results indicate that temperature predictions can be artificially biased if the form factor computation error is lumped into the individual form factors to space.

Tsuyuki, Glenn T.↗

Parallel simulation today

This paper surveys topics that presently define the state of the art in parallel simulation. Included in the tutorial are discussions on new protocols, mathematical performance analysis, time parallelism, hardware support for parallel simulation, load balancing algorithms, and dynamic memory management for optimistic synchronization.

Nicol, David↗

Orbiting transmitter and antenna for spaceborne communications at ELF/VLF to submerged submarines

An orbital emplacement for the transmitter and the antenna of a communications link at ELF (30 to 300 Hz) and VLF (3 kHz to 30 kHz) to submerged submarines has been considered since the very inception of the space age. However, only recently has space technology reached a sufficient level of maturity for system designers to undertake serious studies of this link configuration. The optimistic outlook stems from recent space technology developments, such as the design and construction by NASA of long orbiting tethers, and the testing, onboard Shuttle Orbiter ATLANTIS, of the first spaceborne 20 km metal wire. This is known as the Tethered Satellite System-1 (TSS-1), a space mission that might be possibly followed by other flights, with tether lengths that could reach 100 km. Once deployed at a height of, say, 300 km, from a Shuttle Orbiter, or from another suitable platform, a long, thin tether aligns itself along the local vertical by virtue of the gradient of the Earth gravity field. If made of metal, the tether can function as a VED (Vertical Electric Dipole) transmitting antenna at ELF and VLF.

Bannister, P. R.↗

Luminosity functions for very low mass stars and brown dwarfs

A theoretical investigation of the luminosity function for low-mass objects to constrain the stellar initial mass function at the low-mass end is reported. The ways in which luminosity functions for low-mass stars are affected by star formation histories, brown dwarf and premain-sequence cooling rates and main-sequence mass luminosity relations, and the IMF are examined. Cooling rates and the mass-luminosity relation are determined through a new series of evolutionary calculations for very low mass stars and brown dwarfs in the range 0.05-0.50 solar mass. Model luminosity functions are constructed for specific comparison with the results of four recent observational surveys. The likelihood that the stellar mass function in the solar neighborhood is increasing at masses near the bottom of the main sequence and perhaps at lower masses is confirmed. In the most optimistic case, brown dwarfs contribute half of the local missing disk mass. The actual contribution is likely to be considerably less.

Laughlin, Gregory↗

The X-ray variability of AGN and the anomalous behavior of NGC 6814

The power spectra of the X-ray variable AGN are typically scale invariant with no characteristic timescale. The one strong exception to this is NGC 6814, where the EXOSAT data showed evidence for a periodic component at 12200 +/- 100 seconds. The power spectra of a GINGA lightcurve from this source, found using simulation techniques to account for the uneven sampling, also cannot be well fit by a single power law. A folded light curve analysis of GINGA data shows strong evidence for this periodic component. A second GINGA observation of this source taken one year later is consistent with the phenomena being completely periodic and phase coherent for 7 periods in the range of 12,110-12,145 seconds. Including the (optimistic) limits from the folding selects a period of 12130.39 +/- 0.05 seconds. Phase coherence is not maintained between this and the EXOSAT observations, as the structure of the folded light curves is very different. Thus the periodicity is long lived and stable, but phase coherence is only maintained on timescales of about 1 year.

Done, C.↗

Probabilistic simulation of the human factor in structural reliability

A formal approach is described in an attempt to computationally simulate the probable ranges of uncertainties of the human factor in structural probabilistic assessments. A multi-factor interaction equation (MFIE) model has been adopted for this purpose. Human factors such as marital status, professional status, home life, job satisfaction, work load and health, are considered to demonstrate the concept. Parametric studies in conjunction with judgment are used to select reasonable values for the participating factors (primitive variables). Suitability of the MFIE in the subsequently probabilistic sensitivity studies are performed to assess the validity of the whole approach. Results obtained show that the uncertainties for no error range from five to thirty percent for the most optimistic case.

Chamis, C. C.↗

Results of an observing system simulation experiment based on the proposed Windsat instrument

Two fraternal twin experiments were conducted as part of this study. A data impact experiment using real data (runs 1 and 2) was conducted to assess the impact that rawin wind observations have on both a 5-day assimilation and a single 5-day forecast generated at the end of each assimilation. An observing system simulation experiment (OSSE) using simulated observations (runs 3, 4, and 5) was conducted in order to first calibrate the OSSE results and second to use this calibration to estimate the 'real world' impact from the contribution of global 3-dimensional wind profiles generated from a space-based lidar system known as Windsat. Each of the three runs in the seond experiment were also 5-day assimilation runs with a 5-day forecast initialized from the last 6-hour update cycle of the assimilation. The data impact study revealed a consistent positive impact when rawin winds were added back into an otherwise complete FGGE data set. Both the 6-hour and 5-day forecasts were improved at all levels, in both hemispheres, and for both the wind and the geopotential height fields. Similar results were obtained from the two parallel simulation runs, 3 and 4. Together with the results from runs 1 and 2, calibration coefficients were generated so as to 'correct' the results determined from the addition of Windsat winds (run 5). The Windsat simulation showed a positive improvement in all cases studied. Even though only the tropics were enhanced with these wind observations, hemispheric rms errors were decreased in both the assimilation and 5-day forecast. The 6-hour forecasts of zonal wind from the assimilation run were improved by as much as 50 pct. on the average, and the single forecast showed an average improvement of near 30 pct. Even though these calibrated values are considered too optimistic, the skill of the forecast generated from this run extended the useful forecast period by 18-24 hours.

Arnold, Charles P., Jr.↗

Doppler lidar sampling strategies and accuracies: Regional scale

It has been proposed that a Doppler lidar be placed in a polar orbit and scanned to provide estimates of lower tropospheric winds twice per day and with a spatial resolution of 300 km. Initial feasibility studies conducted primarily by NOAA and NASA presented an optimistic outlook for a space based lidar. The technology appeared within reach and initial computer simulations suggested that acceptable accuracies could be obtained. Those early studies exposed, however, several potential problem areas which included: (1) the algorithms for computing the wind vectors did not perform well when there were coherent gradients in the wind fields; and (2) the lifetime and power requirements of the lidar put severe restrictions on the pulse repetition frequency (PRF). These two basic problems are currently being addressed by a Doppler lidar simulation study focussed upon three primary objectives: (1) to develop optimum scan parameters and shot patterns for a satellite-based Doppler lidar; (2) to develop robust algorithms for computing wind vectors from lidar returns; and (3) to evaluate the impact of coherent mesoscale structures (wind gradients, clouds, aerosols) on up-scale wind estimates. An overview is provided of the simulation efforts with particular emphasis upon rationale and methodology. Since this research is currently underway, any results shown are meant only as evidence of progress.

Emmitt, G. D.↗

Preliminary survey of propulsion using chemical energy stored in the upper atmosphere

Ram-jet cycles that use the chemical energy of dissociated oxygen for propulsion in the ionosphere are presented. After a review of the properties and compositions of the upper atmosphere, the external drag, recombination kinetics, and aerodynamic-heating problems of an orbiting ram jet are analyzed. The study indicates that the recombination ram jet might be useful for sustaining a satellite at an altitude of about 60 miles. Atmospheric composition and recombination-rate coefficients were too uncertain for more definite conclusions. The ram jet is a marginal device even in the optimistic view.

Baldwin, Lionel V↗