SEARCH · Engineering Papers

Results for “nozzles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS1972

Flight investigation of an underwing nacelle installation of three variable-flap ejector nozzles

A modified F-106B aircraft with underwing engine nacelles was flight tested to investigate airframe installation effects on ejector nozzles. Nozzle thrust coefficients, boattail drag coefficients, and boundary layer characteristics were obtained for the three nozzles. All the nozzles were geometrically similar and had 15 deg conical boattails with juncture radii of curvature equal to 0.5 maximum nozzle diameter. The effects of boattail location relative to the wing trailing edge and the ejector to primary nozzle exit diameter ratio were investigated. Shortening the length by 0.48 nozzle diameter lowered the transonic boattail drag rise Mach number from 0.97 to 0.95. Decreasing the nozzle exit diameter, which reduced the ejector to primary nozzle exit diameter ratio from 1.30 to 1.18, increased the gross thrust coefficient 4.8 percent.

Head, V. L.↗

NASA NTRS1975

Flight investigation of installation effects on a wedge nozzle installed on an underwing nacelle

A flight research program was conducted using a modified F-106B aircraft with an underwing-nacelle - engine installation to investigate installation effects on a wedge nozzle with retracted shrouds from Mach 0.70 to 1.10. These configurations simulated the subsonic flight geometries of a variable-geometry wedge nozzle design for Mach 2.70 operation. The nozzle was tested with a J85-GE-13 turbojet engine, and data were compared with that of 0.34-scale isolated wind tunnel model. Data are also compared with the flight results of a boattail plug nozzle and a cylindrical nacelle plug nozzle. A favorable installation effect occurred from Mach 0.82 to 0.96 with a nominal 4-percent corrected secondary weight-flow ratio. This favorable effect resulted from changes in pressure forces on the nozzle surfaces. The wedge nozzle gross thrust coefficient was about the same as the boattail nacelle plug nozzle and 2.50 to 1.30 percent higher than the cylindrical nacelle plug nozzle over the subsonic Mach number range.

Johns, A. L.↗

NASA NTRS1976

Acoustic, performance, and wake survey measurements of a lobed velocity-decayer nozzle installed on a quieted TF-34 turbofan engine

Results for three velocity decayer nozzle configurations are compared with those obtained with a separate flow coannular nozzle tested on the same quieted turbofan engine. Peak sideline noise, which occurred 110 degrees from the inlet, was 2 to 4 db louder than with the coannular nozzle at the same ideal effective exhaust velocity and 8 to 11 db louder at the same thrust level. The decayer nozzles produced an increase in loss equivalent to about 4 percent of the engine thrust and also increased the effective exhaust velocity of the engine. The exhaust decayed to 0.35 of its peak velocity, compared with no decay for the coannular nozzle, within 3 equivalent nozzle diameters of the exit. The peak exhaust gas temperature was 400 K lower for the decayer configuration at the same location. The increase in perceived noise level for the decayer nozzles as compared with the coannular nozzle was attributed to the increase in exhaust velocity and the shift in peak spectrum frequency produced by these nozzles.

Samanich, N. E.↗

NASA NTRS1978

Static performance of five twin-engine nonaxisymmetric nozzles with vectoring and reversing capability

Transonic tunnel test was performed to determine the static performance of five twin-engine nonaxisymmetric nozzles and a base-line axisymmetric nozzle at three nozzle power settings. Static thrust-vectoring and thrust-reversing performance were also determined. Nonaxisymmetric-nozzle concepts included two-dimensional convergent-divergent nozzles, wedge nozzles, and a nozzle with a single external-expansion ramp. All nonaxisymmetric nozzles had essentially the same statis performance as the axisymmetric nozzle. Effective thrust vectoring and reversing was also achieved.

Capone, F. J.↗

NASA NTRS1979

Performance characteristics of nonaxisymmetric nozzles installed on the F-18 aircraft

The Langley Research Center has conducted an experimental program on a model of the F-18 airplane to determine the performance of nonaxisymmetric nozzles relative to the aircraft's baseline axisymmetric nozzle. The performance of a single expansion ramp (ADEN) and two-dimensional convergent-divergent (2-D C-D) nozzle were compared to the baseline axisymmetric nozzles. The effects of vectoring and reversing were also studied. Performance of a modified YF-17 airplane with the ADEN nozzle was also estimated. The results of this investigation indicate that nonaxisymmetric nozzles can be installed on a twin engine fighter airplane with equal or better performance than axisymmetric nozzles. The nonaxisymmetric nozzles also offer potential for innovative and improved aircraft maneuver through thrust vectoring and reversing. The YF-17/ADEN flown as a technology demonstrator would have reduced performance compared to an unmodified YF-17. However, on an equal aircraft weight basis, performance would essentially be equivalent. This study also showed that the YF-17 can serve as a testbed to validate nonaxisymmetric nozzle technology.

Capone, F. J.↗

NASA NTRS1979

Assessment at full scale of exhaust nozzle to wing size on STOL-OTW acoustic characteristics

On the basis of static aero/acoustic data obtained at model scale, the effect of exhaust nozzle size on flyover noise is evaluated at full scale for different STOL-OTW nozzle configurations. Three types of nozzles are evaluated: a circular/deflector nozzle mounted above the wing; a slot/deflector nozzle mounted on the wing; and a slot nozzle mounted on the wing. The nozzle exhaust plane location, measured from the wing leading edge, was varied from 10 to 46 percent of the wing chord (flaps retracted). Flap angles of 20 deg (takeoff) and 60 deg (approach) are included in the study. Initially, perceived noise levels (PNL) are calculated as a function flyover distance at 152m altitude. From these plots, static EPNL values (defined as flyover relative noise levels), are obtained as functions of nozzle size for equal aerodynamic performance (lift and thrust). The acoustic benefits attributable to nozzle size relative to a given wing chord size are assessed.

Vonglahn, U.↗

NASA NTRS1979

Assessment at full scale of exhaust nozzle-to-wing size on STOL-OTW acoustic characteristics

On the basis of static zero/acoustic data obtained at model scale, the effect of exhaust nozzle size on flyover noise is evaluated at full scale for different STOL-OTW nozzle configurations. Three types of nozzles are evaluated: a circular/deflector nozzle mounted above the wing, a slot/deflector nozzle mounted on the wing, and a slot nozzle mounted on the wing. The nozzle exhaust plane location, measured from the wing leading edge was varied from 10 to 46 percent of the wing chord (flaps retracted). Flap angles of 20 deg (takeoff) and 60 deg (approach) are included in the study. Initially, perceived noise levels (PNL) are calculated as a function of flyover distance at 152 m altitude. From these plots static EPNL values, defined as flyover relative noise levels, then are obtained as functions of nozzle size for equal aerodynamic performance (lift and thrust). On the basis of these calculations, the acoustic benefits attributable to nozzle size relative to a given wing chord size are assessed.

Von Glahn, U.↗

NASA NTRS1979

Static source locations for four nozzles mounted on a J-85 engine

The test nozzles included a round 17.5 in. diameter variable flap ejector (VFE) nozzle, a round 'stovepipe' nozzle, and a 104 tube suppressor nozzle operated both with and without an ejector shroud. The velocities tested ranged from 600 to 1600 fps at an approximate total temperature of 1400 R. The axial position of the noise sources during static operation was determined by jet velocity, Strouhal number, and direction of propagation. The velocity dependence was more evident for the 104 tube suppressor nozzle than for the conical nozzles tested. The results for both the VFE conical nozzle and the stovepipe conical nozzle indicate source locations to be much closer to the jet exit plane than expected. Corrections for near field effects were found to differ slightly for each nozzle tested. The corrections presented are simply the differences between the measured near field levels and the required near field levels if spherical spreading is assumed from source to far field.

Hoglund, L. E.↗

NASA NTRS1981

Acoustic and aerodynamic performance investigation of inverted velocity profile coannular plug nozzles

The results of model scale parametric static and wind tunnel aerodynamic performance tests on unsuppressed coannular plug nozzle configurations with inverted velocity profile are discussed. The nozzle configurations are high-radius-ratio coannular plug nozzles applicable to dual-stream exhaust systems typical of a variable cycle engine for Advanced Supersonic Transport application. In all, seven acoustic models and eight aerodynamic performance models were tested. The nozzle geometric variables included outer stream radius ratio, inner stream to outer stream ratio, and inner stream plug shape. When compared to a conical nozzle at the same specific thrust, the results of the static acoustic tests with the coannular nozzles showed noise reductions of up to 7 PNdB. Extensive data analysis showed that the overall acoustic results can be well correlated using the mixed stream velocity and the mixed stream density. Results also showed that suppression levels are geometry and flow regulation dependent with the outer stream radius ratio, inner stream-to-outer stream velocity ratio and inner stream velocity ratio and inner stream plug shape, as the primary suppression parameters. In addition, high-radius ratio coannular plug nozzles were found to yield shock associated noise level reductions relative to a conical nozzle. The wind tunnel aerodynamic tests showed that static and simulated flight thrust coefficient at typical takeoff conditions are quite good - up to 0.98 at static conditions and 0.974 at a takeoff Mach number of 0.36. At low inner stream flow conditions significant thrust loss was observed. Using an inner stream conical plug resulted in 1% to 2% higher performance levels than nozzle geometries using a bent inner plug.

Knott, P. R.↗

NASA NTRS1983

Pressures measured in flight on the aft fuselage and external nozzle of a twin-jet fighter

Fuselage, boundary layer, and nozzle pressures were measured in flight for a twin jet fighter over a Mach number range from 0.60 to 2.00 at test altitudes of 6100, 10,700, and 13,700 meters for angles of attack ranging from 0 deg to 7 deg. Test data were analyzed to find the effects of the propulsion system geometry. The flight variables, and flow interference. The aft fuselage flow field was complex and showed the influence of the vertical tail, nacelle contour, and the wing. Changes in the boattail angle of either engine affected upper fuselage and lower fuselage pressure coefficients upstream of the nozzle. Boundary layer profiles at the forward and aft locations on the upper nacelles were relatively insensitive to Mach number and altitude. Boundary layer thickness decreased at both stations as angle of attack increased above 4 deg. Nozzle pressure coefficient was influenced by the vertical tail, horizontal tail boom, and nozzle interfairing; the last two tended to separate flow over the top of the nozzle from flow over the bottom of the nozzle. The left nozzle axial force coefficient was most affected by Mach number and left nozzle boattail angle. At Mach 0.90, the nozzle axial force coefficient was 0.0013.

Nugent, J.↗

NASA NTRS1983

Effects of varying podded nacelle-nozzle installations on transonic aeropropulsive characteristics of a supersonic fighter aircraft

The aeropropulsive characteristics of an advanced twin engine fighter designed for supersonic cruise was investigated in the 16 foot Transonic Tunnel. The performance characteristics of advanced nonaxisymmetric nozzles installed in various nacelle locations, the effects of thrust induced forces on overall aircraft aerodynamics, the trim characteristics, and the thrust reverser performance were evaluated. The major model variables included nozzle power setting; nozzle duct aspect ratio; forward, mid, and aft nacelle axial locations; inboard and outboard underwing nacelle locations; and underwing and overwing nacelle locations. Thrust vectoring exhaust nozzle configurations included a wedge nozzle, a two dimensional convergent divergent nozzle, and a single expansion ramp nozzle, each with deflection angles up to 30 deg. In addition to the nonaxisymmetric nozzles, an axisymmetric nozzle installation was also tested. The use of a canard for trim was also assessed.

Capone, F. J.↗

NASA NTRS1984

Effects of nozzle design parameters on the extent of quiet test flow at Mach 3.5

Tests results at the NASA Langley Research Center, involving a Mach 3.5 pilot quiet tunnel, have shown that laminar-layered nozzle walls improve boundary layer stability and reduce stream disturbance levels caused by eddy Mach wave radiation. This type of wall design is required to obtain transition Reynolds numbers on tests models as high as those previously observed in supersonic flight vehicles. The Mach 3.5 pilot nozzle wall boundary layers were tested for Tollmein-Schlichting and Goertler linear amplification, and, in an analysis of Goertler vortices in two axisymmetric Mach 5 nozzles, transition values were found to vary. These values were applied to several nozzles with similar throat heights but different expansion rates. Among the nozzles included in the study, a flat-wall radial flow nozzle and a proposed rod-wall nozzle were tested. For the highest test unit Reynolds number, it was determined that the nozzle wall surface finish should not exceed 0.3 micron. Oil flow studies have indicated that Goertler vortex disturbances were the dominant mechanism causing transition on the walls of the pilot nozzle.

Beckwith, I. E.↗

NASA NTRS1984

Free-jet acoustic investigation of high-radius-ratio coannular plug nozzles

The experimental and analytical results of a scale model simulated flight acoustic exploratory investigation of high radius ratio coannular plug nozzles with inverted velocity and temperature profiles are summarized. Six coannular plug nozzle configurations and a baseline convergent conical nozzle were tested for simulated flight acoustic evaluation. The nozzles were tested over a range of test conditions that are typical of a Variable Cycle Engine for application to advanced high speed aircraft. It was found that in simulate flight, the high radius ratio coannular plug nozzles maintain their jet noise and shock noise reduction features previously observed in static testing. The presence of nozzle bypass struts will not significantly affect the acousticn noise reduction features of a General Electric type nozzle design. A unique coannular plug nozzle flight acoustic spectral prediction method was identified and found to predict the measured results quite well. Special laser velocimeter and acoustic measurements were performed which have given new insights into the jet and shock noise reduction mechanisms of coannular plug nozzles with regard to identifying further benificial research efforts.

Knott, P. R.↗

NASA NTRS1987

Experimental study of low Reynolds number nozzles

High-performance electrothermal thrusters operate in a low nozzle-throat Reynolds number regime. Under these conditions, the flow boundary layer occupies a large volume inside the nozzle, contributing to large viscous losses. Four nozzles (conical, bell, trumpet, and modified trumpet) and a sharp-edged orifice were evaluated over a Reynolds number range of 500 to 9000 with unheated nitrogen and hydrogen. The nozzles showed significant decreases in specific impulse efficiency with decreasing Reynolds number. At Reynolds numbers less than 1000, all four nozzles were probably filled with a large boundary layer. The discharge coefficient decreased with Reynolds number in the same manner as the specific impulse efficiency. The bell and modified trumpet nozzles had discharge coefficients 4 to 8 percent higher than those of the cone or trumpet nozzles. The Two-Dimensional Kinetics (TDK) nozzle analysis computer program was used to predict nozzle performance. The results were then compared to the experimental results in order to determine the accuracy of the program within this flow regime.

Grisnik, Stanley P.↗

NASA NTRS1986

Dynamic loads on twin jet exhaust nozzles due to shock noise

Acoustic near field data were collected with model single and twin jet nozzles to determine if closely spaced nozzles produce higher acoustic loading than do single nozzles. The tests were spurred by structural failure of the B-1 exhaust nozzle external flaps and similar damage on the F-15. The test was performed using two 5/8 in. ID pipes machined and placed side-by-side to mimic B-1 nozzles. A microphone mounted on the internozzle fairing measured acoustic levels near the nozzle exit plane. The nozzles oscillated significantly more than did a single nozzle over a wide range of nozzle pressure ratios. Acoustic levels in the dual jets exceeded single jet noise by as much as 20 dB, making acoustic resonance a definite candidate for structural damage in the twin jet configuration.

Norum, T. D.↗

NASA NTRS1987

Experimental study of low Reynolds number nozzles

Grisnik, Stanley P.↗

NASA NTRS1988

Static performance of nonaxisymmetric nozzles with yaw thrust-vectoring vanes

A static test was conducted in the static test facility of the Langley 16 ft Transonic Tunnel to evaluate the effects of post exit vane vectoring on nonaxisymmetric nozzles. Three baseline nozzles were tested: an unvectored two dimensional convergent nozzle, an unvectored two dimensional convergent-divergent nozzle, and a pitch vectored two dimensional convergent-divergent nozzle. Each nozzle geometry was tested with 3 exit aspect ratios (exit width divided by exit height) of 1.5, 2.5 and 4.0. Two post exit yaw vanes were externally mounted on the nozzle sidewalls at the nozzle exit to generate yaw thrust vectoring. Vane deflection angle (0, -20 and -30 deg), vane planform and vane curvature were varied during the test. Results indicate that the post exit vane concept produced resultant yaw vector angles which were always smaller than the geometric yaw vector angle. Losses in resultant thrust ratio increased with the magnitude of resultant yaw vector angle. The widest post exit vane produced the largest degree of flow turning, but vane curvature had little effect on thrust vectoring. Pitch vectoring was independent of yaw vectoring, indicating that multiaxis thrust vectoring is feasible for the nozzle concepts tested.

Mason, Mary L.↗

NASA NTRS1988

Analysis and Optimization of Truncated Scarf Nozzles Subject to External Flow Conditions

Results of a calculation of an optimized truncated scarfed nozzle were compared. The truncated scarfed nozzle was designed for an exit Mach number of 6.0, i.e., the Mach number at the last nozzle characteristic is 6.0, with an external flow Mach number of 5.0. The nozzle was designed by the Rao method for optimum thrust nozzles modified for 2-D flow and truncated scarfed nozzle applications. This design was analyzed using a shock-fitting method for 2-D supersonic flows. Excellent agreement was achieved between the design and analysis. Truncation of the lower nozzle wall (cowl) revealed that there is an optimum length for truncating the cowl without degrading the nozzle performance. Truncation of the nozzle cowl past this optimal length should be analyzed in trade-off studies for thrust loss versus gross vehicle weight. Plots of the oblique shock wave equations were also identified which will allow computation of slip line angle, dynamic pressure coefficient, or ambient Mach number for various specific heat ratios.

Shyne, Rickey J.↗