Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mounting configurations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Low speed aerodynamic characteristics of a transport model having 42.33 deg swept low wing with supercritical airfoil, double-slotted flaps, and T-tail or low tail

A low-speed investigation was conducted in the Langley V/STOL tunnel over an angle-of-attack range of approximately 4 deg to 24 deg to determine the static longitudinal stability characteristics and high lift performance of a general research model which represented an advanced subsonic transport configuration. The model had a 42.33 deg swept, aspect ratio 7.05 wing with a supercritical airfoil and high lift system consisting of a leading edge device (slat or Kruger flap) and a double-slotted flap. The flaps were deflected for take off and landing configurations and were not deflected for tests of the clean configuration. The model was tested with the horizontal tail in either a T tail or low tail position. The effects of various arrangements of flowthrough nacelles which represent a three engine configuration (two large wing-mounted nacelles and a vertical tail mounted nacelle) and a four engine configuration (four smaller wing-mounted nacelles) were determined.

Fournier, P. G.↗
NASA NTRS1982

Inlet and airframe compatibility for a V/STOL fighter/attack aircraft with top-mounted inlets

Aerodynamic force and inlet pressure data are obtained for 9.5% force and pressure models of a V/STOL fighter/attack aircraft configuration with top mounted twin inlets. Data are presented from tests conducted in the Ames Unitary Wind Tunnels at Mach numbers of 0.6, 0.9, and 1.2 at angles of attack up to 27 deg. and angles of sideslip up to 12 deg. Trimmed aerodynamic characteristics and inlet performance are compared for three different leading edge extension (LEX) configurations. The effects of wing leading and trailing-edge flaps on the inlet are also determined. Maneuver perfromance is calculated form combined force and inlet pressure data. The largest of the three LEX sizes tested gives the best airplane maneuver performance. Wing flap deflections improved inlet recovery at all Mach numbers.

Durston, D. A.↗
DOE OSTI2021

Load-decoupling attachment system

A load-decoupling attachment system is configured to secure a component to a primary structure. The load-decoupling system includes a fore end coupling bracket that is configured to attach to a fore end of the component. A first tie rod is coupled to the fore end coupling bracket. The first tie rod is configured to couple to a first portion of the primary structure. A second tie rod is coupled to the fore end coupling bracket. The second tie rod configured to couple to a second portion of the primary structure. A universal joint mount assembly is configured to couple to an aft end of the component and a third portion of the primary structure.

Weathers, Jeffrey W.↗
NASA NTRS1974

Effect of wing-mounted nacelles on a 42 deg swept supercritical wing configuration at near-sonic speeds

An investigation was made to assess the effect of wing-mounted nacelles on a supercritical wing configuration at near-sonic Mach numbers. The investigation was made by utilizing the Cornell Aeronautical Laboratory 8-foot transonic tunnel and covered a Mach number range from 0.90 to 0.99. Force data and pressure measurements at selected locations were obtained. The investigation with the nacelles on included the effect of spanwise location of the nacelle (semispan locations of 35 and 70 percent) and the effect of area ruling for the nacelles located at the 35 percent semispan station. Tests were also made with the outboard nacelle extended forward so that it was directly adjacent to the inboard nacelle location. These tests provided a direct assessment of the extent of the nacelle interference flow field in a lateral direction.

Mckinney, L. W.↗
NASA NTRS1973

Effects of the air breathing propulsion system on space shuttle orbiter subsonic stability and control characteristics (OA71A)

Experimental aerodynamic investigations were conducted on an 0.0405 scale representation of the -89B (2A) Space Shuttle Orbiter in a 7.75 x 11.00 ft low speed wind tunnel during the time period from July 27, 1973 to August 3, 1973. The primary test objective was to investigate the aerodynamic effects of engine nacelle grouping and location on the orbiter ferry mission configuration. Five nacelles were tested, both individually mounted as well as mounted in a podded configuration, at the baseline position and moved 45.0 in. aft (full scale). Orbiter control effectiveness, both with and without nacelles, was recorded at elevon deflections of 0 deg, 5 deg, 10 deg, -10 deg and -20 deg and aileron deflections, about 0 deg elevon, of 0 deg, 5 deg, 10 deg, and 15 deg. The model was sting mounted on a 2.5 inch diameter internal strain gage balance entering through the base region. The nominal angle of attack range was -4 deg or = alpha or = 30 deg. Yaw polars were recorded over the beta range of -10 deg or = beta or = at fixed angles of attack of 0 deg and 10 deg.

Mennell, R. C.↗
NASA NTRS1982

Computation of three-dimensional inviscid flow over hypersonic missile configurations using the GIM code

A three-dimensional computational technique was used to obtain flowfield solutions to the Euler equations over selected hypersonic missile configurations. The General Interpolants Method (GIM) computer code was used with interpolation functions in an algebraic approach to generate a discrete computational grid for each configuration. The spatial marching version of the GIM code, which treats the parabolized Navier-Stokes (PNS) equations or the Euler equations with a shock capturing, 'MacCormack-like' scheme, was used to advance the solution hyperbolically over each configuration. The inviscid flowfield solutions over the two three-dimensional missile configurations, calculated using the GIM hyperbolic scheme, are presented here. The flow field over a wing/body configuration at zero degree angle of attack is presented. Flow over the fuselage of a tactical missile, termed the TAME 10, at both zero degree and 7.5 degree angles of attack is presented. In addition, an inviscid, two-dimensional analysis of an inlet configuration designed to mount on the TAME 10 is included. Contour maps of velocity and pressure are included for each configuration. Comparison of calculation and data show good agreement.

Xiques, K. E.↗
NASA NTRS1989

Use of piezoelectric foil for flow diagnostics

A laboratory investigation was conducted to characterize two piezoelectric-film sensor configurations, a rigidly mounted sensor and a sensor mounted over an air cavity. The sensors are evaluated for sensitivity and frequency response, and methods to optimize data are presented. The cavity-mounted sensor exhibited a superior frequency response and was more sensitive to normal pressure fluctuations and less sensitive to vibrations through the structure. Both configurations were sensitive to large-scale structural vibrations. Flight-test data are shown for cavity-mounted sensors, illustrating practical aspects to consider when designing sensors for application in such harsh environments. The relation of the data to skin friction and maximum shear stress, transition detection, and turbulent viscous layers is derived through analysis of the flight data.

Carraway, Debra L.↗
NASA NTRS1992

Longitudinal and lateral-directional aerodynamic characteristics of a wing-cone configuration at Mach numbers from 2.5 to 4.5

A study was conducted to determine the longitudinal and lateral-directional aerodynamic characteristics of a generic wing-cone configuration at supersonic speeds. The fuselage has a 5 deg half-angle cone forebody, cylindrical midbody, and a 9 deg truncated cone afterbody. The delta wing (aspect ratio 1.0) had a 4 pct. thick diamond airfoil section. The tests were made in the Langley Unitary Plan Wind Tunnel at Mach numbers from 2.50 and 4.50. Angle of attack was varied from -4 to 28 degs, and angle of sideslip varied from -8 to 8 degs. Several configurations were studied to determine the effects of variations in wing longitudinal position, wing incidence, vertical tail configuration, canard shape, and nose bluntness. Typical effects of Reynolds number and Mach number on the longitudinal characteristics were observed. The incremental effects of the configuration variables were generally unaffected by Mach number. The directional stability characteristics of the large and small centerline mounted vertical tail configurations were significantly degraded with increasing angle of attack and Mach number.

Covell, Peter F.↗
NASA NTRS1975

Effects of upper-surface blowing and thrust vectoring on low-speed aerodynamic characteristics of a large-scale supersonic transport model

Tests were conducted in the Langley full-scale tunnel to determine the low-speed aerodynamic characteristics of a large-scale arrow-wing supersonic transport configured with engines mounted above the wing for upper surface blowing, and conventional lower surface engines with provisions for thrust vectoring. A limited number of tests were conducted for the upper surface engine configuration in the high lift condition for beta = 10 in order to evaluate lateral directional characteristics, and with the right engine inoperative to evaluate the engine out condition.

Coe, P. L., Jr.↗
NASA NTRS1978

Instrumentation for measuring the dynamic pressure on rotating compressor blades

To establish the capability for measurement of oscillatory pressure on rotating blades, miniature fast response semiconductor strain gage pressure transducers (2mm x 0.33mm) were mounted in several configurations on thin titanium and steel compressor blades and subjected to pressure cycles from 1 to 310 kPa during static tests and spin tests. Static test conditions included 20 C to 150 C, 0 to 3000 tensile microstrain, -1000 to +1000 bending microstrain and + or - 650G vibration. The spin test conditions included 20 C to 82 C at 0 to 90,000G. Durability was excellent. Pressure transducer sensitivity changed by only a few percent over this range of environmental conditions. Noise signal due to oscillatory acceleration normal to the diaphragm was acceptable (0.33Pa/G). Noise signal due to oscillatory strain was acceptable (0.5 Pa/microstrain) when the transducer was mounted on a 0.05mm rubber pad, with a total buildup of 0.38mm on the measure surface. Back mounting or partial recessing to eliminate buildup, increased the strain effect to 1.2 Pa/microstrain. Flush mounting within the blade to eliminate buildup reduced the strain effect, but required development of a special transducer shape. This transducer was not available in time for spin tests. Unpredictable zero drift + or - 14 kPa ruled out the use of these mounting arrangements for accurate steady-state (D.C.) measurements on rotating blades. The two best configurations fully developed and spin tested were then successfully applied in the NAS3-20606 rotating fan flutter program for quantitative measurement of oscillatory pressure amplitudes.

Grant, H. P.↗
NASA NTRS1990

Experimental investigation of wingtip aerodynamic loading

An experimental investigation was performed to obtain the aerodynamic loading of a series of wingtips. The wingtips varied in taper ratio (1.0, 0.6, and 0.3) and in sweep angle (0, 20, 30, 35, and 45 deg). The wingtips were tested separately (wingtip only configuration) and while mounted on a semi-span wing. The quarter-chord sweep angle of the wing was varied from 30 deg forward sweep, to unswept, to 30 deg. aft sweep. Wingtip loading was obtained from a six component strainguage balance mounted in the wingtip. The effect of wing sweep and wingtip taper and wingtip sweep on the wingtip lift curve slope, drag polar, and pitching moment behavior is discussed. The obtained wingtip data was used to define blade tip platforms, suitable for use in the Free-Tip Rotor configuration. The Free-Tip Rotor has blade tips, which are allowed to weathervane into the blade tip's relative wind. A passive control moment is applied to the blade tip's pitch axis so as to cause blade tip motion around a prescribed null point providing a finite blade tip lift.

Van Aken, Johannes M.↗
NASA NTRS1996

Study of Semi-Span Model Testing Techniques

An investigation has been conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel in order to further the development of semi-span testing capabilities. A twin engine, energy efficient transport (EET) model with a four-element wing in a takeoff configuration was used for this investigation. Initially a full span configuration was tested and force and moment data, wing and fuselage surface pressure data, and fuselage boundary layer measurements were obtained as a baseline data set. The semi-span configurations were then mounted on the wind tunnel floor, and the effects of fuselage standoff height and shape as well as the effects of the tunnel floor boundary layer height were investigated. The effectiveness of tangential blowing at the standoff/floor juncture as an active boundary-layer control technique was also studied. Results indicate that the semi-span configuration was more sensitive to variations in standoff height than to variations in floor boundary layer height. A standoff height equivalent to 30 percent of the fuselage radius resulted in better correlation with full span data than no standoff or the larger standoff configurations investigated. Undercut standoff leading edges or the use of tangential blowing in the standoff/ floor juncture improved correlation of semi-span data with full span data in the region of maximum lift coefficient.

Gatlin, Gregory M.↗
NASA NTRS1976

Investigation of two bifurcated-duct inlet systems from Mach 0 to 2.0 over a wide range of angles of attack

A 15.354 percent/scale lightweight fighter type inlet/forebody was tested over a Mach number range of 0 to 2.0. Model configurations consisted of side mounted normal shock and fixed overhead ramp type inlets. Each configuration consisted of two inlets ducted (bifurcated) to supply a single engine face. The normal shock inlet variables included a boundary layer splitter bleed system, alternate boundary layer splitter plates, alternate upper and lower cowl lip shapes, and a blow-in-door (auxiliary inlet) in one lower lip. The only variable of the fixed overhead ramp inlet was the boundary layer bleed flow. Reynolds numbers ranged from 7.6 x 1 million to 19.5 x 1 million/m. Angle of attack ranged from -10 to 35 deg and angle of sideslip from -8 to 8 deg. Test measurements included engine face total pressure recovery, steady state distortion, dynamic distortion, and surface static pressures on the forebody and inlet surfaces.

Latham, E. A.↗
NASA NTRS1976

Effects of upper-surface blowing and thrust vectoring on low speed aerodynamic characteristics of a large-scale supersonic transport model

Tests were conducted in a full scale tunnel to determine the low speed aerodynamic characteristics of a large scale arrow wing supersonic transport configured with engines mounted above the wing for upper surface blowing and conventional lower surface engines having provisions for thrust vectoring. Tests were conducted over an angle of attack range of -10 deg to 34 deg and for Reynolds numbers (based on the mean aerodynamic chord) of 5.17 x 1 million and 3.89 x 1 million. A limited number of tests were also conducted for the upper surface engine configuration in the high lift condition at an angle of sideslip of 10 deg in order to evaluate lateral directional characteristics and with the right engine inoperative in order to evaluate the engine out condition.

Coe, P. L., Jr.↗
NASA NTRS2011

Turboelectric Distributed Propulsion in a Hybrid Wing Body Aircraft

The performance of the N3-X, a 300 passenger hybrid wing body (HWB) aircraft with turboelectric distributed propulsion (TeDP), has been analyzed to see if it can meet the 70% fuel burn reduction goal of the NASA Subsonic Fixed Wing project for N+3 generation aircraft. The TeDP system utilizes superconducting electric generators, motors and transmission lines to allow the power producing and thrust producing portions of the system to be widely separated. It also allows a small number of large turboshaft engines to drive any number of propulsors. On the N3-X these new degrees of freedom were used to (1) place two large turboshaft engines driving generators in freestream conditions to maximize thermal efficiency and (2) to embed a broad continuous array of 15 motor driven propulsors on the upper surface of the aircraft near the trailing edge. That location maximizes the amount of the boundary layer ingested and thus maximizes propulsive efficiency. The Boeing B777-200LR flying 7500 nm (13890 km) with a cruise speed of Mach 0.84 and an 118100 lb payload was selected as the reference aircraft and mission for this study. In order to distinguish between improvements due to technology and aircraft configuration changes from those due to the propulsion configuration changes, an intermediate configuration was included in this study. In this configuration a pylon mounted, ultra high bypass (UHB) geared turbofan engine with identical propulsion technology was integrated into the same hybrid wing body airframe. That aircraft achieved a 52% reduction in mission fuel burn relative to the reference aircraft. The N3-X was able to achieve a reduction of 70% and 72% (depending on the cooling system) relative to the reference aircraft. The additional 18% - 20% reduction in the mission fuel burn can therefore be attributed to the additional degrees of freedom in the propulsion system configuration afforded by the TeDP system that eliminates nacelle and pylon drag, maximizes boundary layer ingestion (BLI) to reduce inlet drag on the propulsion system, and reduces the wake drag of the vehicle.

Felder, James L.↗
NASA NTRS2016

Assessment of the Noise Reduction Potential of Advanced Subsonic Transport Concepts for NASA's Environmentally Responsible Aviation Project

Aircraft system noise is predicted for a portfolio of NASA advanced concepts with 2025 entry-into-service technology assumptions. The subsonic transport concepts include tube-and-wing configurations with engines mounted under the wing, over the wing nacelle integration, and a double deck fuselage with engines at a mid-fuselage location. Also included are hybrid wing body aircraft with engines upstream of the fuselage trailing edge. Both advanced direct drive engines and geared turbofan engines are modeled. Recent acoustic experimental information was utilized in the prediction for several key technologies. The 301-passenger class hybrid wing body with geared ultra high bypass engines is assessed at 40.3 EPNLdB cumulative below the Stage 4 certification level. Other hybrid wing body and unconventional tube-and-wing configurations reach levels of 33 EPNLdB or more below the certification level. Many factors contribute to the system level result; however, the hybrid wing body in the 301-passenger class, as compared to a tubeand- wing with conventional engine under wing installation, has 11.9 EPNLdB of noise reduction due to replacing reflection with acoustic shielding of engine noise sources. Therefore, the propulsion airframe aeroacoustic interaction effects clearly differentiate the unconventional configurations that approach levels close to or exceed the 42 EPNLdB goal.

Thomas, Russell H.↗