Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “methyl esters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Water Contamination Impacts on Biodiesel Antioxidants and Storage Stability

Biodiesel (fatty acid methyl esters) can oxidize in storage to form acids and gums that negatively impact engine performance and durability. Antioxidant additives are used to increase biodiesel storage stability, and previous studies that evaluated the effectiveness of antioxidants demonstrated that more polar antioxidants tend to be the most effective (provide the largest improvement in stability per unit of antioxidant added). However, polar antioxidants have significant water solubility, and diesel fuel storage tanks are commonly contaminated with water (forming a layer of water under the fuel). This study investigates whether nonpolar antioxidants, which are less effective in dry environments, might be more effective under wet conditions simulating real-world storage. Biodiesel blends treated with polar and nonpolar antioxidants were subjected to accelerated aging using the ASTM D4625 protocol (storage at 43 °C, open to air, for up to 24 weeks) both with and without added water. Fuels treated with polar/higher-effectiveness compounds and stored in contact with water (simulating water in a storage tank) or high humidity showed accelerated loss of stability compared to dry storage. The same fuel treated with a nonpolar antioxidant and stored in the same conditions did not exhibit accelerated stability loss and thus had higher storage stability over the long term despite treatment with an initially less effective additive. Analysis of the fuels during aging showed that this loss of stability was not due to oxidation but rather extraction of the polar antioxidant into the water layer. Antioxidant additives that are incompatible with wet or humid storage conditions were found to cause faster-than-anticipated loss of stability, which was preventable with use of nonpolar additives.

09 BIOMASS FUELS↗
DOE OSTI2016

Understanding How Isotopes Affect Charge Transfer in P3HT/PCBM: A Quantum Trajectory-Electronic Structure Study with Nonlinear Quantum Corrections

The experimentally observed effect of selective deuterium substitution on the open circuit voltage for a blend of poly(3-hexylthiophene)(P3HT) and [6,6]-phenyl-C 61 - butyric acid methyl ester (PCBM) (Nat. Commun. 5:3180, 2014) is explored using a 221-atom model of a polymer-wrapped PCBM molecule. We describe the protonic and deuteronic wavefunctions for the H/D isotopologues of the hexyl side chains within a Quantum Trajectory/Electronic Structure approach where the dynamics is performed with newly developed nonlinear corrections to the quantum forces, necessary to describe the nuclear wavefunctions; the classical forces are generated with a Density Functional Tight Binding method. We used the resulting protonic and deuteronic time-dependent wavefunctions to assess the effects of isotopic substitution (deuteration) on the energy gaps relevant to the charge transfer for the donor and acceptor electronic states. Furthermore, while the isotope effect on the electronic energy levels is found negligible, the quantum-induced fluctuations of the energy gap between the charge transfer and charge separated states due to nuclear wavefunctions may account for experimental trends by promoting charge transfer in P3HT/PCBM and increasing charge recombination on the donor in the deuterium substituted P3HT/PCBM.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Ab Initio Unimolecular Reaction Kinetics of CH 2 C(＝)OCH 3 and CH 3 C(＝O)OCH 2 Radicals

The unimolecular dissociation and isomerization kinetics of the methyl ester combustion intermediates methoxycarbonylmethyl (CH 2 C(＝O)OCH 3 ) and acetyloxylmethyl (CH 3 C(＝O)OCH 2 ) are theoretically investigated using high-level ab initio methods and the Rice–Ramsperger–Kassel–Marcus (RRKM)/master equation (ME) theory. Potential energy surfaces (PESs) are obtained using coupled cluster singles and doubles with perturbative triples correction (CCSD(T)), multireference singles and doubles configuration interaction (MRSDCI) with the Davidson–Silver (DS) correction, and multireference averaged coupled pair functional (MRACPF2) theory. The transition states exhibit high T1 diagnostics in coupled cluster calculations, suggesting the need for a multireference correlated wave function treatment. MRSDCI+DS and MRACPF2 capture their multiconfigurational character well, yielding lower barrier heights than CCSD(T) for these reactions. Additionally, the rate coefficients are computed using the RRKM/ME theory over a 500–2500 K temperature range and at a pressure range of 0.01 atm to the high-pressure limit. The temperature- and pressure-dependent rate coefficients are given in modified Arrhenius expressions. The β-scission of CH 2 C(＝O)OCH 3 is predicted to have a much higher barrier than the corresponding isomerization reaction and the β-scission of CH 3 C(＝O)OCH 2 . Consequently, the rate coefficients for β-scission of CH 2 C(＝O)OCH 3 are the smallest among the three reactions and the isomerization followed by decomposition to CH 3 C(＝O) and HCHO is the dominant reaction pathway for CH 2 C(＝O)OCH 3 . Furthermore, both radicals CH 2 C(＝O)OCH 3 and CH 3 C(＝O)OCH 2 are predicted to mainly decompose to CH 3 C(＝O) + HCHO rather than to the bimolecular product CH 2 C(＝O) + CH 3 O. A newly developed MA combustion mechanism, using our theoretical rate coefficients for the MA-related reactions, predicts combustion properties in good agreement with available experimental data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Investigation of Hierarchical Structure Formation in Merocyanine Photovoltaics

Merocyanines (MCs) are a versatile class of small-molecule dyes. Their optoelectronic properties are easily tunable by chemically controlling their donor–acceptor strength, and their structural properties can be tuned by simple side-chain substitution. This paper demonstrates a novel series of MCs featuring an indoline donor with varying hydrocarbon side-chain length (from 6 to 12 carbons) and a tert-butyl-thiazole acceptor, labeled InTBT. Bulk heterojunction organic photovoltaics are fabricated with a [6,6]-phenyl-C 61 -butyric acid methyl ester (PCBM) acceptor and characterized. Films composed of I8TBT:PCBM and I9TBT:PCBM produced the highest power conversion efficiency of 4.5%, which suggests that the morphology is optimized by controlling the side-chain length. Hierarchical structure formation in InTBT:PCBM films is studied using grazing incidence X-ray diffraction (GIXRD), small-angle neutron scattering (SANS), and atomic force microscopy (AFM). When mixed with PCBM, InTBTs with ≤8 side-chain carbons form pure crystalline domains, while InTBTs with ≥9 side-chain carbons mix well with PCBM. SANS demonstrates that increasing side-chain length increases the InTBT-rich domain size. In addition, a branched hexyl–dodecyl side-chain IHDTBT:PCBM film was studied and found to exhibit the worst-performance organic photovoltaic (OPV) device. The large-branched side chain inhibited mixing between IHDTBT and PCBM resulting in large segregated phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

How the Size and Density of Charge-Transfer Excitons Depend on Heterojunction’s Architecture

We have characterized the size, intensity, density, and distribution of charge-transfer (CT) excitons as a function of the acceptor–donor architecture of prototypical organic interfaces. This characterization was done by computational analysis of 17 models of varying numbers, positions, and orientations of the donor and acceptor molecules. The models’ building blocks were phenyl-C61-butyric acid methyl ester (PCBM) fullerene acceptors and dual-band donor polymers composed of thiophene, benzothiadiazole, and benzotriazole subunits. The electronic structure of the donor–acceptor complexes was computed with the time-dependent long-range-corrected density-functional tight-binding method and analyzed with the fragment-based one-electron transition density matrix. In all models, the complexes with edge-on orientation have denser spectra of low-energy CT states lying below the absorption bands compared to the complexes with face-on orientation. This CT-state distribution in edge-on complexes provides a gate to efficiently populate cold CT excitons. Moreover, the cold CT excitons have a higher degree of charge separation in the edge-on than in the face-on complexes. The CT amount and the CT exciton size generally increase with the energy of the CT states, although the electron remains localized on a single molecule in cold CT states. Delocalization over two PCBM molecules was observed for high-energy CT states. The exciton size also depends on the orientation. Larger excitons are produced by the delocalization of the electrons perpendicularly to the interface. When the delocalization is parallel, the smaller electron–hole distances yield moderately sized CT excitons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Molecular Structure Controlled Transitions between Free-Charge Generation and Trap Formation in a Conjugated Copolymer Series

Charge transfer copolymers, where each repeating unit has at least one “donor” and one “acceptor” block, have played important roles in recent advances in organic photovoltaic (OPV) devices, however design criteria for these materials are still not completely clear. Here we show that the well-recognized LUMO-LUMO energy off-set design criterion for OPV materials using a fullerene acceptor is challenged in a series of copolymers, PTRn (n = 3, 5, 7 and 9), where n is the number of fused aromatic rings in the “donor” block and thienothiophene is the “acceptor” block in each repeating unit. Photoexcitation dynamics of PTRn copolymers in solution and BHJ (bulk heterojunction) films demonstrated that local push-pull interactions between the “donor” block and the “acceptor” block weakens with increasing n, whereas the LUMO-LUMO off-set between the polymer and PC71BM (Phenyl-C71-butyric acid methyl ester) increases. Such a counter intuitive trend can be explained by local energetics of each repeating unit as a function of n. The energetic changes transform the copolymer with strong local charge transfer character for efficient hole-electron separation to localized hole-electron pairs with low mobility, despite the apparent increase of the polymer/PC71BM LUMO-LUMO off-set. This suggests the importance of local charge transfer character in these copolymers in the initial exciton splitting dynamics, which could ultimately be reflected in the device performance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Co-Catalyst Enabled Biotransformation of Polyunsaturated Fatty Acids for Biobased Monomers

Enzymatic lipid epoxidation offers a promising approach to obtain renewable intermediates for biomaterials, but regiochemical control of these reactions has remained elusive. Here we report the discovery and application of artificial cocatalysts to direct the regioselectivity of catalytic epoxidation with the lipase CpLIP2. The methyl esters of alkyl dicarboxylic acids show the unique ability to direct regioselective epoxidation of polyunsaturated fatty acids, major components of plant and algae-based oils. We apply this transformation to the conversion of linoleic acid into sebacic acid, a dicarboxylic acid precursor valuable for biobased polyester polyurethanes, through a six-step pathway involving a regioselective Meinwald rearrangement. To highlight the route’s significance, sebacic acid was used to prepare a 100% biobased thermoplastic polyurethane, illustrating the relevance of this pathway to industrial applications. Furthermore, this regioselective chemoenzymatic oxidation and rearrangement process can be used to access multiple dicarboxylic acids that have remained previously unexplored as biobased monomers.

09 BIOMASS FUELS↗
DOE OSTI2018

Robust Processing of Small-Molecule:Fullerene Organic Solar Cells via Use of Nucleating Agents

The power conversion efficiency (PCE) of small-molecule bulk heterojunction solar cells is highly sensitive to the 'ink' formulation used to produce the photoactive layer. Here we demonstrate that the addition of nucleating agents renders device fabrication notably less susceptible to the ink composition, promising a route toward more robust processing of efficient devices over large areas and enabling more facile materials screening. We selected as a model system blends of 7,7-[4,4-bis(2-ethylhexyl)-4H-silolo[3,2-b:4,5-b]dithiophene-2,6-diyl]bis[6-fluoro-4-(5-hexyl-[2,2-bithiophen]-5-yl)benzo[c][1,2,5]thiadiazole](p-DTS(FBTTh2)2) as the donor and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) as the acceptor because this is one of the small-molecule OPV blends with a device performance that is most sensitive to ink formulation, especially when used with the processing aid diiodooctane (DIO). Addition of DIO is essential to obtain high device performances; however, a notable increase in device performance is only achieved over a very narrow DIO content regime. Use of nucleating agents drastically changes this situation and leads to well-performing devices even at extreme levels of DIO. We thus start to address here one of the great challenges in organic solar cell research: the fact that, too often, only a very limited composition range leads to high efficiency devices. This means that for every new donor or acceptor a multitude of formulations have to be tested, including in combination with processing aids, to ensure that promising materials are not overlooked. The use of nucleating agents, thus, promises to render materials discovery more straightforward as this dependency of device performance with composition can be reduced.

14 SOLAR ENERGY↗
DOE OSTI2016

New Terthiophene-Conjugated Porphyrin Donors for Highly Efficient Organic Solar Cells

To mimic the natural photosynthetic systems utilizing chlorophylls to absorb light and store light energy, two new porphyrin-based small molecules of PTTR and PTTCNR have been developed for photovoltaic applications. The highest power conversion efficiency of 8.21% is achieved, corresponding to a short-circuit current of 14.30 mA cm –2 , open-circuit voltage of 0.82 V, and fill factor of 70.01%. The excellent device performances can be ascribed to the engineering of molecule structure and film morphology. We report the horizontal conjugation of 3,3"-dihexyl-terthiophene to porphyrin-core with the vertical aliphatic 2-octylundecyl peripheral substitutions, can not only effectively increase the solar flux coverage between the conventional Soret and Q bands of porphyrin unit, but also optimize molecular packing through polymorphism associated with side-chains and the linear π-conjugated backbones. And the additive of 1,8-diiodooctane and subsequent chloroform solvent vapor annealing facilitate the formation of the blend films with [6,6]-phenyl-C 71 -butyric acid methyl ester (PC 71 BM) characteristics of bicontinuous, interpenetrating networks required for efficient charge separation and transportation.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Tailoring nanoscale morphology of polymer: Fullerene blends using electrostatic field

In this paper, to tailor the nanoscale phase separation in polymer/fullerene blends, we study the effect of electrostatic field (E-field) on the solidification of poly(3-hexylthiophene-2, 5-diyl) (P3HT):[6,6]-phenyl-C61-butyric acid methyl ester (PC 60 BM) bulk heterojunction (BHJ). In addition to untreated sample (control); wet P3HT:PC 60 BM thin films were exposed to E-field of Van de Graaff (VDG) generator at three different directions – horizontal (H), tilted (T) and vertical (V) – relative to the plane of the substrate. Surface and bulk characterizations of field-treated BHJs affirm that fullerene molecules can easily penetrate the spaghetti-like P3HT and move up and down following the E-field. E-field treatment yields thin films with large P3HT- and PCBM-rich domains acting as continuous pathways for efficient charge separation, transport, and collection. We improve; (1) the hole mobility values up to 19.4 × 10 -4 ± 1.6 × 10 -4 cm 2 V -1 s -1 (117% higher than the control), and (2) power conversion efficient (PCE) of conventional and inverted OPVs recording 2.58 ± 0.02% and 4.1 ± 0.4%. This E-field approach can serve as a new morphology-tuning technique, which is generally applicable to other polymer-fullerene systems.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Beyond Fullerenes: Indacenodithiophene-Based Organic Charge-Transport Layer toward Upscaling of Low-Cost Perovskite Solar Cells

Phenyl-C 61 -butyric acid methyl ester (PCBM) is universally used as the electron-transport layer (ETL) in the low-cost inverted planar structure of perovskite solar cells (PeSCs). PCBM brings tremendous challenges in upscaling of PeSCs using industry-relevant methods due to its aggregation behavior, which undermines the power conversion efficiency and stability. Herein, we highlight these, seldom reported, challenges with PCBM. Moreoever, we investigate the potential of nonfullerene indacenodithiophene (IDT)-based molecules by employing a commercially available variant, 3,9- bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone))- 5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2',3'-d']-s-indaceno[1,2-b:5,6-b'] dithiophene (ITIC), as a PCBM replacement in ambient-processed PeSCs. Films fabrication by laboratory-based spin-coating and industry-relevant slot-die coating methods are compared. While similar power-conversion efficiencies are achieved with both types of ETL in a simple device structure fabricated by spin-coating, the nanofibriller morphology of ITIC compared to the aggregated morphology of PCBM films enables improved mechanical integrity and stability of ITIC devices. Upon slot-die coating, the aggregation of PCBM is exacerbated, leading to significantly lower power-conversion efficiency of devices than spin-coated PCBM as well as slot-diecoated ITIC devices. Our findings clearly suggest that IDT-based molecules have great potential as an ETL in PeSCs, offering superior properties and upscaling compatibility than PCBM. Thus, we present a short summary of recently emerged nonfullerene IDT-based molecules from the field of organic solar cells and discuss their scope in PeSCs as electron or holetransport layer.

42 ENGINEERING↗
DOE OSTI2016

Petascale Simulations of the Morphology and the Molecular Interface of Bulk Heterojunctions

Understanding how additives interact and segregate within bulk heterojunction (BHJ) thin films is critical for exercising control over structure at multiple length scales and delivering improvements in photovoltaic performance. The morphological evolution of poly(3-hexylthiophene) (P3HT) and phenyl-C 61 -butyric acid methyl ester (PCBM) blends that are commensurate with the size of a BHJ thin film is examined using petascale coarse-grained molecular dynamics simulations. When comparing 2 component and 3 component systems containing short P3HT chains as additives undergoing thermal annealing we demonstrate that the short chains alter the morphol- ogy in apparently useful ways: They efficiently migrate to the P3HT/PCBM interface, increasing the P3HT domain size and interfacial area. Simulation results agree with depth profiles determined from neutron reflectometry measurements that reveal PCBM enrichment near substrate and air interfaces, but a decrease in that PCBM enrich- ment when a small amount of short P3HT chains are integrated into the BHJ blend. Atomistic simulations of the P3HT/PCBM blend interfaces show a non-monotonic dependence of the interfacial thickness as a function of number of repeat units in the oligomeric P3HT additive, and the thiophene rings orient parallel to the interfacial plane as they approach the PCBM domain. Using the nanoscale geometries of the P3HT oligomers, LUMO and HOMO energy levels calculated by density functional theory are found to be invariant across the donor/acceptor interface. Finally, these connections between additives, processing, and morphology at all length scales are generally useful for efforts to improve device performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Surfactant Engineering and Its Role in Determining the Performance of Nanoparticulate Organic Photovoltaic Devices

The fabrication of organic photovoltaics (OPVs) from non-hazardous nanoparticulate (NP) inks offers considerable promise for the development of ecofriendly large-scale printed solar modules. However, the typical NP core-shell morphology (driven by the different donor/acceptor affinities for the surfactant used in NP synthesis) currently hinders the photovoltaic performance. As such, surfactant engineering offers an elegant approach to synthesizing a more optimal intermixed NP morphology and hence an improved photovoltaic performance. In this work, the morphology of conventional sodium dodecyl sulfate (SDS) and 2-(3-thienyl) ethyloxybutylsulfonate (TEBS)-stabilized poly(3-hexylthiophene) (P3HT) donor:phenyl-C 61 -butyric acid methyl ester (PC 61 BM) acceptor NPs is probed using scanning transmission X-ray microscopy, UV-vis spectroscopy, grazing-incidence X-ray diffraction, and scanning electron microscopy. While the SDS-stabilized NPs exhibit a size-independent core-shell morphology, this work reveals that TEBS-stabilized NPs deliver an intermixed morphology, the extent of which depends on the particle size. Consequently, by optimizing the TEBS-stabilized NP size and distribution, NP-OPV devices with a power conversion efficiency that is ~50% higher on average than that of the corresponding SDS-based NP-OPV devices are produced.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Emergent Chemical Behavior in Mixed Food and Lignocellulosic Green Waste Hydrothermal Liquefaction

Hydrothermal liquefaction (HTL) is a promising strategy for the conversion of energy-dense waste streams to fuels. Mixed-feed HTL aggregates multiple feed streams to achieve greater scales that capitalize on local resources, hence lowering costs. The potential for new pathways and products upon feedstock blending becomes a compounding level of complexity when unlocking emergent chemistries. Here, food and green waste streams were evaluated under HTL conditions (300 °C, 1 h) to understand the effect of feed molecular composition on product distributions and mechanisms. Thousands of emergent chemical compounds were detected via Fourier transform ion cyclotron resonance mass spectrometry, ultimately leading to the emergence of two dominant outcomes. First, the presence of small amounts of food waste into green waste results in substantial decarboxylation and subsequent polymerization to biocrude than chars. Second, in the other limit, small amounts of green waste promote the capping of oxygenates into the biodiesel range, such as with the emergence of fatty acid methyl esters.

09 BIOMASS FUELS↗
DOE OSTI2013

Certification of alternative aviation fuels and blend components

Aviation turbine engine fuel specifications are governed by ASTM International, formerly known as the American Society for Testing and Materials (ASTM) International, and the British Ministry of Defence (MOD). ASTM D1655 Standard Specification for Aviation Turbine Fuels and MOD Defence Standard 91-91 are the guiding specifications for this fuel throughout most of the world. Both of these documents rely heavily on the vast amount of experience in production and use of turbine engine fuels from conventional sources, such as crude oil, natural gas condensates, heavy oil, shale oil, and oil sands. Turbine engine fuel derived from these resources and meeting the above specifications has properties that are generally considered acceptable for fuels to be used in turbine engines. Alternative and synthetic fuel components are approved for use to blend with conventional turbine engine fuels after considerable testing. ASTM has established a specification for fuels containing synthesized hydrocarbons under D7566, and the MOD has included additional requirements for fuels containing synthetic components under Annex D of DS91-91. New turbine engine fuel additives and blend components need to be evaluated using ASTM D4054, Standard Practice for Qualification and Approval of New Aviation Turbine Fuels and Fuel Additives. This paper discusses these specifications and testing requirements in light of recent literature claiming that some biomass-derived blend components, which have been used to blend in conventional aviation fuel, meet the requirements for aviation turbine fuels as specified by ASTM and the MOD. The 'Table 1' requirements listed in both D1655 and DS91-91 are predicated on the assumption that the feedstocks used to make fuels meeting these requirements are from approved sources. Recent papers have implied that commercial jet fuel can be blended with renewable components that are not hydrocarbons (such as fatty acid methyl esters). These are not allowed blend components for turbine engine fuels as discussed in this paper.

09 BIOMASS FUELS↗
DOE OSTI2024

Chain-End Controlled Depolymerization Selectivity in α,α-Disubstituted Propionate PHAs with Dual Closed-Loop Recycling and Record-High Melting Temperature

In this article, within the large poly(3-hydroxyalkanoate) (PHA) family, C3 propionates are much less studied than C4 butyrates, with the exception of α,α-disubstituted propionate PHAs, particularly poly(3-hydroxy-2,2-dimethylpropionate), P3H(Me) 2 P, due to its high melting temperature (T m ~ 230 °C) and crystallinity (~76%). However, inefficient synthetic routes to its monomer 2,2-dimethylpropiolactone [(Me) 2 PL] and extreme brittleness of P3H(Me) 2 P largely hinder its broad applications. Here, we introduce simple, efficient step-growth polycondensation (SGP) of a hydroxyacid or methyl ester to afford P3H(Me) 2 P with low to medium molar mass, which is then utilized to produce lactones through base-catalyzed depolymerization. The ring-opening polymerization (ROP) of the 4-membered lactone leads to high-molar-mass P3H(Me) 2 P, which can be depolymerized by hydrolysis to the hydroxyacid in 99% yield or methanolysis to the hydroxyester in 91% yield, achieving closed-loop recycling via both SGP and ROP routes. Intriguingly, the chain end of the SGP-P3H(Me) 2 P determines the depolymerization selectivity toward 4- or 12-membered lactone formation, while both can be repolymerized back to P3H(Me) 2 P. Through the formation of copolymers P3H(Me/R) 2 P (R = Et, n Pr), PHAs with high tensile strength and ductility, coupled with high barriers to water vapor and oxygen, have been created. Notably, the PHA structure–property study led to P3H( n Pr) 2 P with a record-high T m of 266 °C within the PHA family.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗